IXP425 TEXT_BASE
Hi;
I am trying to bring up u-boot-2009-08-rc1 on IXP425 board. May
I know what's the reason that the TEXT_BASE is 0x00f80000 instead of 0 or 0x50000000?
Thanks.
Regards,
KH
Quoted 8 lines · Teh Kok How
Hi;
I am trying to bring up u-boot-2009-08-rc1 on IXP425 board. May
I know what's the reason that theTEXT_BASEis0x00f80000instead of 0 or0x50000000?Thanks.
Hi Teh,
usually TEXT_BASE is offset, which size depends on your requirements for stack size and memory size for malloc. If your DRAM base is 0x0 and TEXT_BASE is 0xf80000, you will have almost 16Mb for stack and malloc and your u-boot code will be linked and loaded to 0xf80000 address. 16Mb is probably too much, or your DRAM base is not 0x0.
It's only my experience with porting u-boot to Gemini arch, and I may be wrong.
regards,
Darius A.
Quoted 15 lines
Regards,
KH
------------------------------------------------------------------------
_______________________________________________
U-Boot mailing list
U-Boot at lists.denx.de
http://lists.denx.de/mailman/listinfo/u-boot
Dear Darius Augulis,
Quoted 2 lines · In message <[email protected]> you wrote:
usually
TEXT_BASEis offset, which size depends on your requirements for
No. TEXT_BASE is an absolute address.
Quoted 4 lines
stack size and memory size for malloc. If your DRAM base is
0x0andTEXT_BASEis0xf80000, you will have almost 16Mb for stack and malloc and your u-boot code will be linked and loaded to0xf80000address. 16Mb is probably too much, or your DRAM base is not0x0.
On architectures like ARM (where the implementation is based on a broken concept of the system memory map) TEXT_BASE should always be chosen to be as high as possible to put the ("relocated") U-Boot code as close as possible to the very end of available RAM. For systems with several RAM size options you have to set this according to the smallest possible RAM size, of course (which is a major PITA).
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Vulcans worship peace above all. -- McCoy, "Return to Tomorrow", stardate 4768.3
Quoted 6 lines · Wolfgang Denk
Dear Darius Augulis,
Quoted 1 line · In message<[email protected]> you wrote:
usually
TEXT_BASEis offset, which size depends on your requirements forNo.
TEXT_BASEis an absolute address.
yes, but depends on the physical RAM base and size.
Quoted 6 lines
Quoted 5 lines
stack size and memory size for malloc. If your DRAM base is
0x0andTEXT_BASEis0xf80000, you will have almost 16Mb for stack and malloc and your u-boot code will be linked and loaded to0xf80000address. 16Mb is probably too much, or your DRAM base is not0x0.
Quoted 6 lines
On architectures like ARM (where the implementation is based on a broken concept of the system memory map)
TEXT_BASEshould always be chosen to be as high as possible to put the ("relocated") U-Boot code as close as possible to the very end of available RAM. For systems with several RAM size options you have to set this according to the smallest possible RAM size, of course (which is a major PITA).
could you please explain more? why to the end of RAM?
for example I have 16MB RAM, base is 0x10000000. TEXT_BASE = 0x10400000. Why is better to set this to 0x10F00000 ? To have more stack and malloc memory? But U-boot will never exceed such limit? Please explain where I am wrong. Thanks!
Darius A.
Quoted 6 lines
Best regards,
Wolfgang Denk
Dear Darius Augulis,
Quoted 4 lines · In message <[email protected]> you wrote:
Quoted 2 lines
No.
TEXT_BASEis an absolute address.yes, but depends on the physical RAM base and size.
Only on ARM (and other architectures that copied it's broken implementation). TEXT_BASE is an absolute address (in the boot flash) on PowerPC.
Quoted 1 line
could you please explain more? why to the end of RAM?
YOu want to have a maximum of contiguous RAM available to load Linux kernel, ramdisk images etc.
Quoted 4 lines
for example I have 16MB RAM, base is
0x10000000.TEXT_BASE=0x10400000. Why is better to set this to0x10F00000? To have more stack and malloc memory? But U-boot will never exceed such limit? Please explain where I am wrong. Thanks!
With RAM from 0x10000000...0x10ffffff you should probably put TEXT_BASE at 0x10f80000 which then would leave you some 15 MB of contiguous RAM for your use.
With your setup you jusy have some 3+ MB below U-Boot and some 11+ MB above it. It makes not much sense to have U-Boot sitting right in the middle of precious RAM like this.
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de The idea of male and female are universal constants. -- Kirk, "Metamorphosis", stardate 3219.8
Hi;
I understand Wolfgang's argument but setting the TEXT_BASE to this
arbitrary high address (DRAM_end - U-boot_size(_end - _start)) does not make sense. I am new to ARM arch but in PowerPC and MIPS, the TEXT_BASE is always set to the reset vector and in ARM, the reset vector is at 0 or 0xFFFF0000. I have tried both values but still failed to boot u-boot on the board....:-(
Regards,
Teh
-----Original Message-----
From: [email protected] [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Wolfgang Denk
Sent: Tuesday, August 04, 2009 11:57 PM
To: Darius Augulis
Cc: u-boot at lists.denx.de
Subject: Re: [U-Boot] IXP425 TEXT_BASE
Dear Darius Augulis,
Quoted 4 lines · In message <[email protected]> you wrote:
Quoted 2 lines
No.
TEXT_BASEis an absolute address.yes, but depends on the physical RAM base and size.
Only on ARM (and other architectures that copied it's broken implementation). TEXT_BASE is an absolute address (in the boot flash) on PowerPC.
Quoted 1 line
could you please explain more? why to the end of RAM?
YOu want to have a maximum of contiguous RAM available to load Linux kernel, ramdisk images etc.
Quoted 4 lines
for example I have 16MB RAM, base is
0x10000000.TEXT_BASE=0x10400000. Why is better to set this to0x10F00000? To have more stack and malloc memory? But U-boot will never exceed such limit? Please explain where I am wrong. Thanks!
With RAM from 0x10000000...0x10ffffff you should probably put TEXT_BASE at 0x10f80000 which then would leave you some 15 MB of contiguous RAM for your use.
With your setup you jusy have some 3+ MB below U-Boot and some 11+ MB above it. It makes not much sense to have U-Boot sitting right in the middle of precious RAM like this.
Best regards,
Wolfgang Denk
Signature · 9 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de The idea of male and female are universal constants. -- Kirk, "Metamorphosis", stardate 3219.8 _______________________________________________ U-Boot mailing list U-Boot at lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
Hmmm...I can answer myself now. The flash programmer programs the content from TEXT_BASE to end of the u-boot image into flash start location 0x5000_0000. When u-boot boots, it relocates itself from flash to DRAM location @TEXT_BASE. I still haven't managed to bring up the board. Guess there are some GPIO pins which I have not initialized properly.
-----Original Message-----
From: [email protected] [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Teh Kok How
Sent: Wednesday, August 05, 2009 11:22 AM
To: 'Wolfgang Denk'; 'Darius Augulis'
Cc: u-boot at lists.denx.de
Subject: Re: [U-Boot] IXP425 TEXT_BASE
Hi;
I understand Wolfgang's argument but setting the TEXT_BASE to this
arbitrary high address (DRAM_end - U-boot_size(_end - _start)) does not make sense. I am new to ARM arch but in PowerPC and MIPS, the TEXT_BASE is always set to the reset vector and in ARM, the reset vector is at 0 or 0xFFFF0000. I have tried both values but still failed to boot u-boot on the board....:-(
Regards,
Teh
-----Original Message-----
From: [email protected] [mailto:u-boot-bounces at lists.denx.de] On Behalf Of Wolfgang Denk
Sent: Tuesday, August 04, 2009 11:57 PM
To: Darius Augulis
Cc: u-boot at lists.denx.de
Subject: Re: [U-Boot] IXP425 TEXT_BASE
Dear Darius Augulis,
Quoted 4 lines · In message <[email protected]> you wrote:
Quoted 2 lines
No.
TEXT_BASEis an absolute address.yes, but depends on the physical RAM base and size.
Only on ARM (and other architectures that copied it's broken implementation). TEXT_BASE is an absolute address (in the boot flash) on PowerPC.
Quoted 1 line
could you please explain more? why to the end of RAM?
YOu want to have a maximum of contiguous RAM available to load Linux kernel, ramdisk images etc.
Quoted 4 lines
for example I have 16MB RAM, base is
0x10000000.TEXT_BASE=0x10400000. Why is better to set this to0x10F00000? To have more stack and malloc memory? But U-boot will never exceed such limit? Please explain where I am wrong. Thanks!
With RAM from 0x10000000...0x10ffffff you should probably put TEXT_BASE at 0x10f80000 which then would leave you some 15 MB of contiguous RAM for your use.
With your setup you jusy have some 3+ MB below U-Boot and some 11+ MB above it. It makes not much sense to have U-Boot sitting right in the middle of precious RAM like this.
Best regards,
Wolfgang Denk
Signature · 14 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de The idea of male and female are universal constants. -- Kirk, "Metamorphosis", stardate 3219.8 _______________________________________________ U-Boot mailing list U-Boot at lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot _______________________________________________ U-Boot mailing list U-Boot at lists.denx.de http://lists.denx.de/mailman/listinfo/u-boot
Dear "Teh Kok How",
Quoted 4 lines · In message <[email protected]> you wrote:
I understand Wolfgang's argument but setting the
TEXT_BASEto this
arbitrary high address (DRAM_end- U-boot_size(_end -_start)) does not make sense. ...
Maybe it makes little (or even no sense) to you. But you should not generalize such a statement.
Quoted 2 lines
... I am new to ARM arch but in PowerPC and MIPS, the
TEXT_BASEis always
set to the reset vector ...
This is plain wrong.
See for example:
"board/tqc/tqm8xx/config.mk":
TEXT_BASE = 0x40000000 These are low-booting MPC8xx systems, i. e. the reset vector is 0x100.
"board/amcc/canyonlands/config.mk":
TEXT_BASE = 0xFFFA0000 This is a PPC460EX based system, i. e. the reset vector is 0xFFFFFFFC
Quoted 2 lines
... and in ARM, the reset vector is at 0 or 0xFFFF0000.I have tried both values but still failed to boot u-boot on the board....:-(
No big surprise since your changes are based on misunderstandings.
Best regards,
Wolfgang Denk
Signature · 5 lines
DENX Software Engineering GmbH, MD: Wolfgang Denk & Detlev Zundel HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de Fascinating is a word I use for the unexpected. -- Spock, "The Squire of Gothos", stardate 2124.5