AS352X SOC02:Part03 for U-boot1.1.6
PATCH 1/1 AS352X SOC02:Part03 for U-boot1.1.6
U-Boot1.1.6 for AS352X
Port to U-boot to New ARM base SOC AS352X, support NAND flash Boot. please ref:
http://www.austriamicrosystems.com/03products/products_detail/AS3525/AS3525.htm
Part 3:
Br
Signed-off-by: Thomas Luothomas.luo at austriamicrosystems.com
--------------------------------------------------------------------------------------------------
include/as352x.h 2006-12-05 09:50:51.000000000 +0800 renamed from include/as352x.h 1970-01-01 08:00:00.000000000 +0800 +492 -0
@@ -0,0 +1,492 @@ +/* +* (C) Copyright 2006 +* Copyright (C) 2006 Austriamicrosystems, by thomas.luo +* +* This program is free software; you can redistribute it and/or +* modify it under the terms of the GNU General Public License as +* published by the Free Software Foundation; either version 2 of +* the License, or (at your option) any later version. +* +* This program is distributed in the hope that it will be useful, +* but WITHOUT ANY WARRANTY; without even the implied warranty of +* MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the +* GNU General Public License for more details. +* +* You should have received a copy of the GNU General Public License +* along with this program; if not, write to the Free Software +* Foundation, Inc., 59 Temple Place, Suite 330, Boston, +* MA 02111-1307 USA +*/ +#ifndef __AS352X_H__ +#define __AS352X_H__ + +#define AS352X_UART_CHANNELS 1 + +/* AS352X only supports 512 Byte HW ECC */ +#define AS352X_ECCSIZE 512 +#define AS352X_ECCBYTES 3 + + +/* AS352X device base addresses */ + + +/* ----------------------------------------------------------------- +* AS352X Registers +* ------------------------------------------------------------------ +* +*/ + + +/* AHB */ +#define AS352X_USB_BASE 0xC6000000 +#define AS352X_VIC_BASE 0xC6010000 +#define AS352X_DMAC_BASE 0xC6020000 +#define AS352X_MPMC_BASE 0xC6030000 +#define AS352X_MEMSTICK_BASE 0xC6040000 +#define AS352X_CF_IDE_BASE 0xC6050000 + +/* APB */ +#define AS352X_NAND_FLASH_BASE 0xC8000000 +#define AS352X_BIST_MANAGER_BASE 0xC8010000 +#define AS352X_SD_MCI_BASE 0xC8020000 +#define AS352X_TIMER_BASE 0xC8040000 +#define AS352X_WDT_BASE 0xC8050000 +#define AS352X_I2C_MS_BASE 0xC8060000 +#define AS352X_I2C_AUDIO_BASE 0xC8070000 +#define AS352X_SSP_BASE 0xC8080000 +#define AS352X_I2SIN_BASE 0xC8090000 +#define AS352X_I2SOUT_BASE 0xC80A0000 +#define AS352X_GPIO1_BASE 0xC80B0000 +#define AS352X_GPIO2_BASE 0xC80C0000 +#define AS352X_GPIO3_BASE 0xC80D0000 +#define AS352X_GPIO4_BASE 0xC80E0000 +#define AS352X_CGU_BASE 0xC80F0000 +#define AS352X_CCU_BASE 0xC8100000 +#define AS352X_UART0_BASE 0xC8110000 +#define AS352X_DBOP_BASE 0xC8120000 + + + +/* ------------------------------------------------------------------------ +* AS352X control registers +* ------------------------------------------------------------------------ +*/ + +#define CCU_SRC ( (AS352X_CCU_BASE) + 0x00) +#define CCU_SRL ( (AS352X_CCU_BASE) + 0x04) +#define CCU_MEMMAP ( (AS352X_CCU_BASE) + 0x08) +#define CCU_IO ( (AS352X_CCU_BASE) + 0x0C) +#define CCU_SCON ( (AS352X_CCU_BASE) + 0x10) +#define CCU_VERS ( (AS352X_CCU_BASE) + 0x14) + + +/** +* Reset Control Lines in CCU_SRC register +**/ +#define CCU_SRC_DBOP_EN ( 1 << 24 ) +#define CCU_SRC_SPDIF_EN ( 1 << 22 ) +#define CCU_SRC_TIMER_EN ( 1 << 21 ) +#define CCU_SRC_SSP_EN ( 1 << 20 ) +#define CCU_SRC_WDO_EN ( 1 << 19 ) +#define CCU_SRC_IDE_EN ( 1 << 18 ) +#define CCU_SRC_IDE_AHB_EN ( 1 << 17 ) +#define CCU_SRC_UART0 ( 1 << 16 ) +#define CCU_SRC_NAF_EN ( 1 << 15 ) +#define CCU_SRC_SDMCI_EN ( 1 << 14 ) +#define CCU_SRC_GPIO_EN ( 1 << 13 ) +#define CCU_SRC_I2C_AUDIO_EN ( 1 << 12 ) +#define CCU_SRC_I2C_EN ( 1 << 11 ) +#define CCU_SRC_MST_EN ( 1 << 10 ) +#define CCU_SRC_I2SIN ( 1 << 9 ) +#define CCU_SRC_I2SOUT ( 1 << 8 ) +#define CCU_SRC_USB_AHB_EN ( 1 << 7 ) +#define CCU_SRC_USB_PHY_EN ( 1 << 6 ) +#define CCU_SRC_DMAC_EN ( 1 << 5 ) +#define CCU_SRC_VIC_EN ( 1 << 4 ) + +/** +* Magic number for CCU_SRL for reset. +**/ +#define CCU_SRL_MAGIC_NUMBER 0x1A720212 + +/** +* Chip select lines for NAF. Use these constants to +*select/deselct the CE lines for NAND flashes in Register CCU_IO. +**/ +#define CCU_IO_NAF_CE_LINE_0 ( 0 << 7 ) +#define CCU_IO_NAF_CE_LINE_1 ( 1 << 7 ) +#define CCU_IO_NAF_CE_LINE_2 ( 2 << 7 ) +#define CCU_IO_NAF_CE_LINE_3 ( 3 << 7 ) + +/* CCU IO Select/Deselect IDE */ +#define CCU_IO_IDE ( 1 << 5 ) + +/* CCU IO Select/desect I2C */ +#define CCU_IO_I2C_MASTER_SLAVE ( 1 << 1 ) + +/* CCU IO Select/desect UART */ +#define CCU_IO_UART0 ( 1 << 0 ) + + +#define CCU_RESET_ALL_BUT_MEMORY \ + ( CCU_SRC_DBOP_EN \ + | CCU_SRC_SPDIF_EN \ + | CCU_SRC_TIMER_EN \ + | CCU_SRC_SSP_EN \ + | CCU_SRC_WDO_EN \ + | CCU_SRC_IDE_EN \ + | CCU_SRC_IDE_AHB_EN \ + | CCU_SRC_UART0 \ + | CCU_SRC_NAF_EN \ + | CCU_SRC_SDMCI_EN \ + | CCU_SRC_GPIO_EN \ + | CCU_SRC_I2C_AUDIO_EN \ + | CCU_SRC_I2C_EN \ + | CCU_SRC_MST_EN \ + | CCU_SRC_I2SIN \ + | CCU_SRC_I2SOUT \ + | CCU_SRC_USB_AHB_EN \ + | CCU_SRC_USB_PHY_EN \ + | CCU_SRC_DMAC_EN \ + | CCU_SRC_VIC_EN \ + ) + +/** +* Magic number for CCU_SRL for reset. +**/ +#define CCU_SRL_MAGIC_NUMBER 0x1A720212 + +/** +* Chip select lines for NAF. Use these constants to select/deselct +* the CE lines for NAND flashes in Register CCU_IO. +**/ +#define CCU_IO_NAF_CE_LINE_0 ( 0 << 7 ) +#define CCU_IO_NAF_CE_LINE_1 ( 1 << 7 ) +#define CCU_IO_NAF_CE_LINE_2 ( 2 << 7 ) +#define CCU_IO_NAF_CE_LINE_3 ( 3 << 7 ) + +/* CCU IO Select/Deselect IDE */ +#define CCU_IO_IDE ( 1 << 5 ) + +/* CCU IO Select/desect I2C */ +#define CCU_IO_I2C_MASTER_SLAVE ( 1 << 1 ) + +/* CCU IO Select/desect UART */ +#define CCU_IO_UART ( 1 << 0 ) + + +#define CCU_COUNT_MIN_10_MICROSEC 640 + +/* ------------------------------------------------------------------------ +* AS352X clock control registers +* ------------------------------------------------------------------------ +*/ + +#define CGU_REG_PLLA ( (AS352X_CGU_BASE) + 0x00 ) +#define CGU_REG_PLLB ( (AS352X_CGU_BASE) + 0x04 ) +#define CGU_REG_PLLASUP ( (AS352X_CGU_BASE) + 0x08 ) +#define CGU_REG_PLLBSUP ( (AS352X_CGU_BASE) + 0x0C ) +#define CGU_REG_PROC ( (AS352X_CGU_BASE) + 0x10 ) +#define CGU_REG_PERI ( (AS352X_CGU_BASE) + 0x14 ) +#define CGU_REG_AUDIO ( (AS352X_CGU_BASE) + 0x18 ) +#define CGU_REG_USB ( (AS352X_CGU_BASE) + 0x1C ) +#define CGU_REG_INTCTRL ( (AS352X_CGU_BASE) + 0x20 ) +#define CGU_REG_IRQ ( (AS352X_CGU_BASE) + 0x24 ) +#define CGU_REG_COUNTA ( (AS352X_CGU_BASE) + 0x28 ) +#define CGU_REG_COUNTB ( (AS352X_CGU_BASE) + 0x2C ) +#define CGU_REG_IDE ( (AS352X_CGU_BASE) + 0x30 ) +#define CGU_REG_MEMSTICK ( (AS352X_CGU_BASE) + 0x34 ) +#define CGU_REG_DBOP ( (AS352X_CGU_BASE) + 0x38 ) + + +/* --- are disabled after reset --- */ +/* dma */ +#define CGU_DMA_CLOCK_ENABLE ( 1 << 22 ) +/* usb */ +#define CGU_USB_CLOCK_ENABLE ( 1 << 21 ) +/* i2sout */ +#define CGU_I2SOUT_APB_CLOCK_ENABLE ( 1 << 20 ) +/* i2sin */ +#define CGU_I2SIN_APB_CLOCK_ENABLE ( 1 << 19 ) +/* i2c master/slave */ +#define CGU_I2C_MASTER_SLAVE_CLOCK_ENABLE ( 1 << 18 ) +/* i2c audio master */ +#define CGU_I2C_AUDIO_MASTER_CLOCK_ENABLE ( 1 << 17 ) +/* gpio */ +#define CGU_GPIO_CLOCK_ENABLE ( 1 << 16 ) +/* mmc + sd */ +#define CGU_MCI_CLOCK_ENABLE ( 1 << 15 ) +/* naf */ +#define CGU_NAF_CLOCK_ENABLE ( 1 << 14 ) + /* uart */ +#define CGU_UART_APB_CLOCK_ENABLE ( 1 << 13 ) +/* watchdog counter */ +#define CGU_WDOCNT_CLOCK_ENABLE ( 1 << 12 ) + /* watchdog timer module */ +#define CGU_WDOIF_CLOCK_ENABLE ( 1 << 11 ) +/* ssp */ +#define CGU_SSP_CLOCK_ENABLE ( 1 << 10 ) +/* timer 1 */ +#define CGU_TIMER1_CLOCK_ENABLE ( 1 << 9 ) +/* timer 2 */ +#define CGU_TIMER2_CLOCK_ENABLE ( 1 << 8 ) +/* timer interface */ +#define CGU_TIMERIF_CLOCK_ENABLE ( 1 << 7 ) + +/** ------------------------------------------------------------------ +* Number of cycles to wait before cgu is safely locked. +**/ +#define CGU_LOCK_CNT 0xFF + +/* FIFO depth is 16 for tx and rx fifo */ +#define UART_FIFO_DEPTH 16 + +/* ------------------- UART Line Control Register bit fields ------------- */ + +#define UART_LNCTL_DLSEN (1 << 7) /* Device latch select bit */ + + +/* -------------- UART Interrupt Control Register bit fields ---------- */ + +#define UART_INTR_RXDRDY 0x1 /* Data ready interrupt */ +#define UART_INTR_TXEMT 0x2 /* Transmit data empty interrupt */ +#define UART_INTR_RXLINESTATUS 0x4 /* Receive line status interrupt */ + +/* ------------------- UART Line Status Register bit fields ------------- */ + +#define UART_ERRORBITS 0x1E +#define UART_RX_DATA_READY (1 << 0) +#define UART_TX_HOLD_REG_EMPTY (1 << 5) + +/* ------------------- FIFO CNTL Register contants --------------*/ + +#define UART_FIFO_EN (1 << 0) /* Enable the UART FIFO */ +#define UART_TX_FIFO_RST (1 << 1) /* Enable the UART FIFO */ +#define UART_RX_FIFO_RST (1 << 2) +#define UART_RXFIFO_TRIGLVL_1 (0 << 4) /* RX FIFO TRIGGER_LEVEL 1 */ +#define UART_RXFIFO_TRIGLVL_4 0x08 /* RX FIFO TRIGGER_LEVEL 4 */ +#define UART_RXFIFO_TRIGLVL_8 0x10 /* RX FIFO TRIGGER_LEVEL 8 */ +#define UART_RXFIFO_TRIGLVL_14 0x18 /* RX FIFO TRIGGER_LEVEL 14 */ + + +/* ------------------- FIFO status Register contants -----------*/ +#define UART_TX_FIFO_FULL (1 << 0) +#define UART_RX_FIFO_FULL (1 << 1) +#define UART_TX_FIFO_EMPTY (1 << 2) +#define UART_RX_FIFO_EMPTY (1 << 3) + + +/* ----------------------- defines -------------------------------------- */ +/* Data register */ +#define UART_DATA_REG ( (AS352X_UART0_BASE) + 0x00 ) +/* Clock divider(lower byte) register */ +#define UART_DLO_REG ( (AS352X_UART0_BASE) + 0x00 ) +/* Clock divider(higher byte) register */ +#define UART_DHI_REG ( (AS352X_UART0_BASE) + 0x04 ) +/* Interrupt enable register */ +#define UART_INTEN_REG ( (AS352X_UART0_BASE) + 0x04 ) +/* Interrupt status register */ +#define UART_INTSTATUS_REG ( (AS352X_UART0_BASE) + 0x08 ) +/* Fifo control register */ +#define UART_FCTL_REG ( (AS352X_UART0_BASE) + 0x0C ) +/* Fifo status register */ +#define UART_FSTATUS_REG ( (AS352X_UART0_BASE) + 0x0C ) +/* Line control register */ +#define UART_LNCTL_REG ( (AS352X_UART0_BASE) + 0x10 ) +/* Line status register */ +#define UART_LNSTATUS_REG ( (AS352X_UART0_BASE) + 0x14 ) + +/* 32-bit width */ +#define TIMER_LOAD ( (AS352X_TIMER_BASE) + 0x00 ) +/* 32 bit width */ +#define TIMER_VALUE ( (AS352X_TIMER_BASE) + 0x04 ) +/* 8 bit width */ +#define TIMER_CONTROL ( (AS352X_TIMER_BASE) + 0x08 ) +/* clears ir by write access */ +#define TIMER_INTCLR ( (AS352X_TIMER_BASE) + 0x0C ) +/* 1 bit width */ +#define TIMER_RIS ( (AS352X_TIMER_BASE) + 0x10 ) + /* 1 bit width */ +#define TIMER_MIS ( (AS352X_TIMER_BASE) + 0x14 ) + +/** +* Counter/Timer control register bits +**/ +#define TIMER_ENABLE 0x80 +#define TIMER_PERIODIC 0x40 +#define TIMER_INT_ENABLE 0x20 +#define TIMER_32_BIT 0x02 +#define TIMER_ONE_SHOT 0x01 +#define TIMER_PRESCALE_1 0x00 +#define TIMER_PRESCALE_16 0x04 +#define TIMER_PRESCALE_256 0x08 + + + +#define NAF_CONFIG ( (AS352X_NAND_FLASH_BASE) + 0x00 ) +#define NAF_CONTROL ( (AS352X_NAND_FLASH_BASE) + 0x04 ) +#define NAF_ECC ( (AS352X_NAND_FLASH_BASE) + 0x08 ) +#define NAF_DATA ( (AS352X_NAND_FLASH_BASE) + 0x0C ) +#define NAF_MODE ( (AS352X_NAND_FLASH_BASE) + 0x10 ) +#define NAF_STATUS ( (AS352X_NAND_FLASH_BASE) + 0x14 ) +#define NAF_MASK ( (AS352X_NAND_FLASH_BASE) + 0x18 ) +#define NAF_FIFODATA ( (AS352X_NAND_FLASH_BASE) + 0x1C ) +#define NAF_WORDS ( (AS352X_NAND_FLASH_BASE) + 0x20 ) +#define NAF_CLEAR ( (AS352X_NAND_FLASH_BASE) + 0x24 ) +#define NAF_TEST ( (AS352X_NAND_FLASH_BASE) + 0x28 ) + +/* Macro introduced to compensate for no support for floating +point division operation in the processor. So to get the correct value, +roundup is peformed to provide accurate results for certain conditions. */ + +#define DIVIDE_AND_ROUND_UP(dividend,divisor) \ + ( ( (dividend) + (divisor) - 1 ) / (divisor) ) + +/* For sake of completness and for easier exchanging of +round-up and round-down divisions provide also a round-down macro */ + +#define DIVIDE_AND_ROUND_DOWN( a , b ) ((a)/(b)) + +/* Macro which evaluates to the absolute value of an integer value*/ +#define ABS(A) (((A)>0)?(A):(-(A))) + + +/* ------------------------defines for Dynamic Mem ----------------- */ +#define AS352X_SDRAM_BASE_ADDR(offset) (0xc6030000 + offset) + +#define AS352X_MPMC_CONTROL AS352X_SDRAM_BASE_ADDR( 0x00 ) +#define AS352X_MPMC_CONFIG AS352X_SDRAM_BASE_ADDR( 0x08 ) +#define AS352X_MPMC_DYRDCFG AS352X_SDRAM_BASE_ADDR( 0x28 ) +#define AS352X_MPMC_DYTRP AS352X_SDRAM_BASE_ADDR( 0x30 ) +#define AS352X_MPMC_DYTRAS AS352X_SDRAM_BASE_ADDR( 0x34 ) +#define AS352X_MPMC_DYTSREX AS352X_SDRAM_BASE_ADDR( 0x38 ) +#define AS352X_MPMC_DYTAPR AS352X_SDRAM_BASE_ADDR( 0x3C ) +#define AS352X_MPMC_DYTDAL AS352X_SDRAM_BASE_ADDR( 0x40 ) +#define AS352X_MPMC_DYTWR AS352X_SDRAM_BASE_ADDR( 0x44 ) +#define AS352X_MPMC_DYTRC AS352X_SDRAM_BASE_ADDR( 0x48 ) +#define AS352X_MPMC_DYTRFC AS352X_SDRAM_BASE_ADDR( 0x4C ) +#define AS352X_MPMC_DYTXSR AS352X_SDRAM_BASE_ADDR( 0x50 ) +#define AS352X_MPMC_DYTRRD AS352X_SDRAM_BASE_ADDR( 0x54 ) +#define AS352X_MPMC_DYTMRD AS352X_SDRAM_BASE_ADDR( 0x58 ) +#define AS352X_MPMC_DYRASCAS0 AS352X_SDRAM_BASE_ADDR( 0x104 ) +#define AS352X_MPMC_DYCONFIG0 AS352X_SDRAM_BASE_ADDR( 0x100 ) +#define AS352X_MPMC_DYCNTL AS352X_SDRAM_BASE_ADDR( 0x20 ) +#define AS352X_MPMC_DYREF AS352X_SDRAM_BASE_ADDR( 0x24 ) + +/* --- MT48LC4M16A2 SDRAM & MT48LC32M16A2 SDRAM ----------------- */ +#define MPMC_DY_TRP_IN_NS 20 +#define MPMC_CLK_IN_MHZ_MIN 20 +#define MPMC_1_CLKCYCLE_IN_NS_MIN 50 + +#define MPMC_CLK_IN_MHZ 66 +#if MPMC_CLK_IN_MHZ == 24 +#define MPMC_1_CLKCYCLE_IN_NS 42 +#elif MPMC_CLK_IN_MHZ == 66 +#define MPMC_1_CLKCYCLE_IN_NS 16 +#else +#define MPMC_1_CLKCYCLE_IN_NS 16 +#endif +#define MPMC_SDRAM_TCK_IN_NS 10 + +#define MPMC_DY_TRAS_MIN_IN_NS 50 +#define MPMC_DY_TRAS_IN_NS MPMC_DY_TRAS_MIN_IN_NS + +/* tAPR not available for micron MT48LC4M16A2 SDRAM */ +#define MPMC_DY_TAPR_INNS 0 + +#define MPMC_DY_TDAL_IN_NS (5 * (MPMC_SDRAM_TCK_IN_NS)) + +/* tWR can be minimum 15ns or 1CLK * 7ns */ +#define MPMC_DY_TWR_IN_NS (MPMC_1_CLKCYCLE_IN_NS + 8) +#define MPMC_DY_TRC_IN_NS 70 + +#define MPMC_DY_TRFC_INNS 70 + +#define MPMC_DY_TXSR_IN_NS 80 + +#define MPMC_DY_TRRD_IN_NS 20 +#define MPMC_DY_TMRD_IN_NS (2 * (MPMC_SDRAM_TCK_IN_NS)) + +#define MPMC_SDRAM_CAS 0x2 +#define MPMC_SDRAM_RAS 0x2 /* hha??? */ + +/* Low Power device bit settings */ +/* Device Type for APP Board 2.0 and 1.0 */ +/* MT48LC32M16A2 - 512Mbit and MT48LC4M16 - 64Mbit -both NOT Low Power */ +#define MPMC_SDRAM_DEVICE_TYPE (0 << 3) + +/*ROW and COLUMN size mapping for mpmc SoC device */ + +/* Addr Mapping for APP Board 2.0 (MT48LC32M16A2 - 512Mbit) */ +#define MPMC_SDRAM_ADDR_MAPPING (0x11 << 7) + +#define MPMC_SDRAM_32BIT_EXTBUS (0 <<14) +#define MPMC_SDRAM_BUFFER_DISABLE (0 <<19) +#define MPMC_SDRAM_BUFFER_ENABLE (1 <<19) +#define MPMC_SDRAM_WP_ENABLE (0 <<20) + +#define MPMC_SDRAM_DYN_CONFIG ((MPMC_SDRAM_DEVICE_TYPE) | \ + (MPMC_SDRAM_ADDR_MAPPING) | \ + (MPMC_SDRAM_32BIT_EXTBUS) | \ + (MPMC_SDRAM_BUFFER_DISABLE) | \ + (MPMC_SDRAM_WP_ENABLE)) + +#define MPMC_SDRAM_START_2_REF_CYCLES 2 +/* TREF for APP Board 2.0 (MT48LC32M16A2 - 512Mbit) */ +/*64ms divided by 8192 */ +#define MPMC_SDRAM_tREF_inNs 7812 + + +#define MPMC_SDRAM_DYNAMIC_REF ((MPMC_SDRAM_tREF_inNs) \ + / (MPMC_1_CLKCYCLE_IN_NS_MIN)) + +/* CAS Latency for APP Board 2.0 (MT48LC32M16A2 - 512Mbit) */ +#if MPMC_SDRAM_CAS == 2 +#define MPMC_SDRAM_MODEVALUE (0x23 << 13) +#else +#define MPMC_SDRAM_MODEVALUE (0x33 << 13) +#endif +/* Quarter Strength*/ +#define MPMC_SDRAM_EXMODEVALUE ((0x40 << 12) | (0x1 << 11)) + +#define set_reg_bits32( registerAddress, value ) \ + ( *( (volatile u32 *)(registerAddress) ) |= ( (u32)(value) ) ) + + +#define clr_reg_bits32( registerAddress, value ) \ + ( *( (volatile u32 *)(registerAddress) ) &= ( ~( (u32)(value) ) ) ) + +#define read_reg32( registerAddress ) \ + ( *( ( const volatile u32 * )( registerAddress ) ) ) + +#define write_reg32( registerAddress, value ) \ + ( *( (volatile u32 *)(registerAddress) ) = ( (u32)(value) ) ) + + + +#define read_reg16( registerAddress ) \ + ( *( ( const volatile u16 * )( registerAddress ) ) ) + +#define write_reg16( registerAddress, value ) \ + ( *( (volatile u16 *)(registerAddress) ) = ( (u16)(value) ) ) + +#define set_reg_bits16( registerAddress, value ) \ + ( *( (volatile u16 *)(registerAddress) ) |= ( (u16)(value) ) ) + +#define clr_reg_bits16( registerAddress, value ) \ + ( *( (volatile u16 *)(registerAddress) ) &= ( ~( (u16)(value) ) ) ) + + +#define read_reg8( registerAddress ) \ + ( *( ( const volatile u8 * )( registerAddress ) ) ) + +#define write_reg8( registerAddress, value ) \ + ( *( (volatile u8 *)(registerAddress) ) = ( (u8)(value) ) ) + +#define set_reg_bits8( registerAddress, value ) \ + ( *( (volatile u8 *)(registerAddress) ) |= ( (u8)(value) ) ) + +#define clr_reg_bits8( registerAddress, value ) \ + ( *( (volatile u8 *)(registerAddress) ) &= ( ~( (u8)(value) ) ) ) +/* Wait until rINTPND is changed for the case that the ISR is very short. */ +#endif /*__AS352X_H__*/
include/asm-arm/mach-types.h 2006-12-01 18:01:45.000000000 +0800 renamed from include/asm-arm/mach-types.h 2006-12-01 17:49:35.000000000 +0800 +14 -1
@@ -737,6 +737,7 @@ extern unsigned int __machine_arch_type; #define MACH_TYPE_CB3RUFC 726 #define MACH_TYPE_MP2USB 727 #define MACH_TYPE_PDNB3 1002 +#define MACH_TYPE_AS352X 1166 #ifdef CONFIG_ARCH_EBSA110 # ifdef machine_arch_type
@@ -6054,7 +6055,7 @@ extern unsigned int __machine_arch_type; # define machine_is_ess710() (0) #endif -#ifdef CONFIG_MACH_MX3ADS +#ifdef CONFIG_MACH_MX31ADS # ifdef machine_arch_type # undef machine_arch_type # define machine_arch_type __machine_arch_type
@@ -9401,6 +9402,18 @@ extern unsigned int __machine_arch_type; #else # define machine_is_mp2usb() (0) #endif +#ifdef CONFIG_MACH_AS352X +# ifdef machine_arch_type +# undef machine_arch_type +# define machine_arch_type __machine_arch_type +# else +# define machine_arch_type MACH_TYPE_AS352X +# endif +# define machine_is_as352x() (machine_arch_type == MACH_TYPE_AS352X) +#else +# define machine_is_as352x() (0) +#endif + /* * These have not yet been registered
include/configs/as352xpb.h 2006-12-05 16:06:36.000000000 +0800 renamed from include/configs/as352xpb.h 1970-01-01 08:00:00.000000000 +0800 +232 -0
232 lines not on this page · raw message
MAINTAINERS 2006-12-04 10:20:27.000000000 +0800 renamed from MAINTAINERS 2006-12-01 17:49:32.000000000 +0800 +11 -0
@@ -566,6 +566,17 @@ Zachary P. Landau <zachary.landau at labxte Haavard Skinnemoen <[email protected]> ATSTK1000 AT32AP7000 +######################################################################### +# AS352X Systems: # +# # +# Maintainer Name, Email Address # +# Board CPU # +######################################################################### + +Thomas Luo <[email protected]> + + AS352XPB AS352X + ######################################################################### # End of MAINTAINERS list #
MAKEALL 2006-12-04 10:20:27.000000000 +0800 renamed from MAKEALL 2006-12-01 17:49:32.000000000 +0800 +2 -2
@@ -189,13 +189,13 @@ LIST_ARM7=" \ LIST_ARM9=" \ at91rm9200dk cmc_pu2 \ ap920t ap922_XA10 ap926ejs ap946es \ - ap966 cp920t cp922_XA10 cp926ejs \ + ap966 cp920t cp922t cp922_XA10 cp926ejs \ cp946es cp966 lpd7a400 mp2usb \ mx1ads mx1fs2 netstar omap1510inn \ omap1610h2 omap1610inn omap730p2 sbc2410x \ scb9328 smdk2400 smdk2410 trab \ VCMA9 versatile versatileab versatilepb \ - voiceblue \ + voiceblue as3525pb \ " #########################################################################
Makefile 2006-12-04 10:20:27.000000000 +0800 renamed from Makefile 2006-12-01 17:49:33.000000000 +0800 +3 -0
@@ -2253,6 +2253,9 @@ atstk1002_config : unconfig @./mkconfig $(@:_config=) avr32 at32ap atstk1000 atmel at32ap7000 ######################################################################### +as352xpb_config : unconfig + @$(MKCONFIG) $(@:_config=) arm arm922t as352xpb NULL as352x + ######################################################################### #########################################################################