Skip to contentSkip to conversation

respawning too fast

DISCUSSION Ing.Gianfranco Morandi 2 participants 2 messages Oct 25, 2002 – Oct 26, 2002

lore
Share & tools
lore
#0 lore raw

Finally I have solved the starting problem on my EST8260 board. I have burned the flash with the PPCboot 1.20 and I've been able to load any
kernel: M.V. 2.4.2 and ELDK 2.4.4.
Now I was trying to go ahead with a newer version of kernel (i.e. 2.4.18) and now this is what happens:

BOOTP broadcast 1
ARP broadcast 1
TFTP from server 10.0.0.10; our IP address is 10.0.0.20 Filename '/tftpboot/image'.
Load address: 0x500000
Loading: #################################################################

         ###############################
done
Bytes transferred = 491392 (77f80 hex)
## Booting image at 00500000 ...
   Image Name:   FEC-Linux 2.4.18
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    491328 Bytes = 479.8 kB

Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Memory BAT mapping: BAT2=64Mb, BAT3=0Mb, residual: 0Mb
..................
..................
Sending BOOTP requests . OK
IP-Config: Got BOOTP answer from 10.0.0.10, my address is 10.0.0.20
IP-Config: Complete:

      device=eth0, addr=10.0.0.20, mask=255.0.0.0, gw=255.255.255.255,
     host=10.0.0.20, domain=, nis-domain=(none),
     bootserver=10.0.0.10, rootserver=10.0.0.10, rootpath=/opt/eldk/ppc_82xx

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Looking up port of RPC 100003/2 on 10.0.0.10
Looking up port of RPC 100005/1 on 10.0.0.10
VFS: Mounted root (nfs filesystem).
Freeing unused kernel memory: 52k init
tty_io.c: process 1 (swapper) used obsolete /dev/cua - update software to use /d
ev/ttyS0
tty_io.c: process 1 (init) used obsolete /dev/cua - update software to use /dev/
ttyS0
tty_io.c: process 1 (init) used obsolete /dev/cua - update software to use /dev/
ttyS0
INIT: tty_io.c: process 1 (init) used obsolete /dev/cua - update software to use
/dev/ttyS0
version 2.78 bootingtty_io.c: process 1 (init) used obsolete /dev/cua - update s
oftware to use /dev/ttyS0
Welcome to DENX Embedded Linux Environment
Press 'I' to enter interactive startup.

Mounting proc filesystem:  [  OK  ]
Configuring kernel parameters:  [  OK  ]
Cannot access the Hardware Clock via any known method.
Use the --debug option to see the details of our search for an access
method.
Setting clock : Wed Dec 31 19:00:07 EST 1969 [  OK  ]
Activating swap partitions:  [  OK  ]
Setting hostname 10.0.0.20:  [  OK  ]
Checking filesystems
Checking all file systems.
[  OK  ]
Mounting local filesystems:  [  OK  ]
Enabling swap space:  [  OK  ]
INIT: Entering runlevel: 3

Entering non-interactive startup
Starting system logger: [ OK ]
Starting kernel logger: [ OK ]
Starting xinetd: [ OK ]
INIT: Id "3" respawning too fast: disabled for 5 minutes
INIT: no more processes left in this runlevel

I don't understand the messages related to the /dev/cua (these messages were not present with the ELDK) and why the INIT process doesn't let me get the console prompt.

Any suggestions?

Thanks
Gianfranco

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/

#1 lore raw

Is there a proper define of /dev/console?

-----Original Message-----
From: Ing.Gianfranco Morandi [mailto:[email protected]]
Sent: Friday, October 25, 2002 5:28 PM
To: LinuxPPC
Subject: respawning too fast

Finally I have solved the starting problem on my EST8260 board. I have burned the flash with the PPCboot 1.20 and I've been able to load any
kernel: M.V. 2.4.2 and ELDK 2.4.4.
Now I was trying to go ahead with a newer version of kernel (i.e. 2.4.18) and now this is what happens:

BOOTP broadcast 1
ARP broadcast 1
TFTP from server 10.0.0.10; our IP address is 10.0.0.20 Filename '/tftpboot/image'.
Load address: 0x500000
Loading: #################################################################

         ###############################
done
Bytes transferred = 491392 (77f80 hex)
## Booting image at 00500000 ...
   Image Name:   FEC-Linux 2.4.18
   Image Type:   PowerPC Linux Kernel Image (gzip compressed)
   Data Size:    491328 Bytes = 479.8 kB

Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
Uncompressing Kernel Image ... OK
Memory BAT mapping: BAT2=64Mb, BAT3=0Mb, residual: 0Mb
..................
..................
Sending BOOTP requests . OK
IP-Config: Got BOOTP answer from 10.0.0.10, my address is 10.0.0.20
IP-Config: Complete:

      device=eth0, addr=10.0.0.20, mask=255.0.0.0, gw=255.255.255.255,
     host=10.0.0.20, domain=, nis-domain=(none),
     bootserver=10.0.0.10, rootserver=10.0.0.10, rootpath=/opt/eldk/ppc_82xx

NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Looking up port of RPC 100003/2 on 10.0.0.10
Looking up port of RPC 100005/1 on 10.0.0.10
VFS: Mounted root (nfs filesystem).
Freeing unused kernel memory: 52k init
tty_io.c: process 1 (swapper) used obsolete /dev/cua - update software to use /d
ev/ttyS0
tty_io.c: process 1 (init) used obsolete /dev/cua - update software to use /dev/
ttyS0
tty_io.c: process 1 (init) used obsolete /dev/cua - update software to use /dev/
ttyS0
INIT: tty_io.c: process 1 (init) used obsolete /dev/cua - update software to use
/dev/ttyS0
version 2.78 bootingtty_io.c: process 1 (init) used obsolete /dev/cua - update s
oftware to use /dev/ttyS0
Welcome to DENX Embedded Linux Environment
Press 'I' to enter interactive startup.

Mounting proc filesystem:  [  OK  ]
Configuring kernel parameters:  [  OK  ]
Cannot access the Hardware Clock via any known method.
Use the --debug option to see the details of our search for an access
method.
Setting clock : Wed Dec 31 19:00:07 EST 1969 [  OK  ]
Activating swap partitions:  [  OK  ]
Setting hostname 10.0.0.20:  [  OK  ]
Checking filesystems
Checking all file systems.
[  OK  ]
Mounting local filesystems:  [  OK  ]
Enabling swap space:  [  OK  ]
INIT: Entering runlevel: 3

Entering non-interactive startup
Starting system logger: [ OK ]
Starting kernel logger: [ OK ]
Starting xinetd: [ OK ]
INIT: Id "3" respawning too fast: disabled for 5 minutes
INIT: no more processes left in this runlevel

I don't understand the messages related to the /dev/cua (these messages were not present with the ELDK) and why the INIT process doesn't let me get the console prompt.

Any suggestions?

Thanks
Gianfranco

** Sent via the linuxppc-embedded mail list. See http://lists.linuxppc.org/