Skip to contentSkip to conversation

Help with PRIO qdisc and filters

LARTC Pavan Kumar 2 participants 2 messages May 10, 2005 – May 11, 2005

lore
Share & tools
lore
#0 lore raw

Hi,
Sorry to bother you all. I have a typical problem sharing DSL upstream bandwidth with users. I have 3 types of traffic high-priority, medium-priority and low priority. My upstream rate is 960kbits. Traffic (any priority) can vary in bandwidth from 0 to 960kbits. I have a test setup where I can pump 600kbit of high priority sustained and I have 400kbit of low priority traffic sustained. I expect after the 600kbit high-priority traffic, the remaining 360kbit should be allocated to the medium and low priority. Since I do not have medium-priority everything should go to low-priority traffic. However, I do not see that behavior with the following tc script I have

----------- Begin Script -------------

# delete any existing qdiscs
tc qdisc del dev ppp0 root
# setup PRIO qdisc with 3 bands
tc qdisc add dev ppp0 root handle 1: prio band 3 priomap 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0
# filter traffic for high priority based on TOS field
tc filter add dev ppp0 parent 1:0 prio 1 protocol ip u32 match ip tos 0x28
0xff flowid 1:1
tc filter add dev ppp0 parent 1:0 prio 1 protocol ip u32 match ip tos 0x48
0xff flowid 1:2
tc filter add dev ppp0 parent 1:0 prio 1 protocol ip u32 match ip tos 0x58
0xff  flowid 1:3
# use ebtables to set the TOS field. First flush the rules
ebtables -t broute -F
ebtables -t broute -I BROUTING 1 -j ftos --set-ftos 0x28 -p IPv4 --ip-src
192.168.1.151/32
ebtables -t broute -I BROUTING 2 -j ftos --set-ftos 0x48 -p IPv4 --ip-src
192.168.1.152/32
ebtables -t broute -I BROUTING 3 -j ftos --set-ftos 0x58 -p IPv4 --ip-src
192.168.1.153/32

----------- End Script ------------------

What I see is the high priority traffic is leaving at 600kbits as I measure it on my test equipment. However, I do not see any low-priority or medium-priority traffic coming out of the box. I would appreciate if you folks can please give me a hint as to what is happening and also any possible solutions. I need hard PRIO but the unused bandwidth should be shared by the other traffic. I am using Linux kernel 2.6.8.1 and iproute2 (iproute2-2.6.8-ss040730.tar.gz).

Regards,
Pavan Kumar

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc

#1 lore raw
Quoted 37 lines · Pavan Kumar

Hi,
Sorry to bother you all. I have a typical problem sharing DSL upstream bandwidth with users. I have 3 types of traffic high-priority, medium-priority and low priority. My upstream rate is 960kbits. Traffic (any priority) can vary in bandwidth from 0 to 960kbits. I have a test setup where I can pump 600kbit of high priority sustained and I have 400kbit of low priority traffic sustained. I expect after the 600kbit high-priority traffic, the remaining 360kbit should be allocated to the medium and low priority. Since I do not have medium-priority everything should go to low-priority traffic. However, I do not see that behavior with the following tc script I have

----------- Begin Script -------------

# delete any existing qdiscs
tc qdisc del dev ppp0 root
# setup PRIO qdisc with 3 bands
tc qdisc add dev ppp0 root handle 1: prio band 3 priomap 0 0 0 0 0 0 0 0 0 0
0 0 0 0 0 0
# filter traffic for high priority based on TOS field
tc filter add dev ppp0 parent 1:0 prio 1 protocol ip u32 match ip tos 0x28
0xff flowid 1:1
tc filter add dev ppp0 parent 1:0 prio 1 protocol ip u32 match ip tos 0x48
0xff flowid 1:2
tc filter add dev ppp0 parent 1:0 prio 1 protocol ip u32 match ip tos 0x58
0xff  flowid 1:3
# use ebtables to set the TOS field. First flush the rules
ebtables -t broute -F
ebtables -t broute -I BROUTING 1 -j ftos --set-ftos 0x28 -p IPv4 --ip-src
192.168.1.151/32
ebtables -t broute -I BROUTING 2 -j ftos --set-ftos 0x48 -p IPv4 --ip-src
192.168.1.152/32
ebtables -t broute -I BROUTING 3 -j ftos --set-ftos 0x58 -p IPv4 --ip-src
192.168.1.153/32

----------- End Script ------------------

Quoted 7 lines

What I see is the high priority traffic is leaving at 600kbits as I measure it on my test equipment. However, I do not see any low-priority or medium-priority traffic coming out of the box. I would appreciate if you folks can please give me a hint as to what is happening and also any possible solutions. I need hard PRIO but the unused bandwidth should be shared by the other traffic. I am using Linux kernel 2.6.8.1 and iproute2 (iproute2-2.6.8-ss040730.tar.gz).

You need to have prio as an htb class as it doesn't rate limit otherwise .

You'll also need to back off from your dsl rate to allow for overheads as they can be significant especially with lots of small packets.

Andy.

_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc