Skip to contentSkip to conversation

Timedia MultiFunction Card Support

DISCUSSION Robert Currey 1 participant 1 message Sep 18, 2003

lore
Share & tools
lore
#0 lore raw

Hi all,

I'm trying to ready a patch (off of 2.6.0-test5) to 8250_pci.c, parport_pc.c, and parport_serial.c to cleanup and support the Timedia based serial, parallel, and serial/parallel combo cards. It appears some cleanup is in order here, and I'd appreciate opinions on how I should proceed. This is the first time I've prepared a patch for submission, so prepare for some noobness ....

My goal is to get a Timedia 4089 (2 serial/2 parallel multi-function card) to be recognized. What I've found is ...

1) Insmodding 8250_pci alone gets the driver to probe and find the serial ports. It then proceeds to init them wrong (at least for multi-function cards).
2) Insmodding parport_pc alone gets the driver to recognize the parallel ports and config them correctly.
3) Once either 8250_pci or parport_pc inits, the other doesn't get a chance to setup the card (hence the need for parport_serial).
4) Insmodding parport_serial is a problem since either parport_pc or 8250_pci get to the card first.

So, It seems to me that 8250_pci and parport_pc should *not* be trying to init these mutifunction cards (that's the job of parport_serial).

Currently I have things working where the pci_timedia_init() returns an error for multiport cards (which keeps the 8250_pci from initting the card). In parport_pc, I can remove the 18 table entries corresponding to the multifunction cards.

The last task is to fix this ...

        /* Timedia/SUNIX uses a mixture of BARs and offsets */
        /* Ugh, this is ugly as all hell --- TYT */
        if(dev->vendor == PCI_VENDOR_ID_TIMEDIA )  /* 0x1409 */
                switch(idx) {
                        case 0: base_idx=0;
                                break;
                        case 1: base_idx=0; offset=8;
                                break;
                        case 2: base_idx=1;
                                break;
                        case 3: base_idx=1; offset=8;
                                break;
                        case 4: /* BAR 2*/
                        case 5: /* BAR 3 */
                        case 6: /* BAR 4*/
                        case 7: base_idx=idx-2; /* BAR 5*/
                }

Yup, ugly as hell, and broken for multifunction cards. I only have my one 2s/2p card, so figuring the correct algorithm may be tricky. I'm guessing that this works for the pure serial cards, and can be left alone in 8250_pci.c. For parport_serial, this is simply wrong (unless I'm really missing something).

Now for the questions ...

1) Should I put in ifdef CONFIG_PARPORT_SERIAL to keep the definitions of multifunction cards out of 8250_pci and parport_pc, or just whack them completely? The ifdef seems nicer, but retains broken cruft.

2) Any insight on the best means to patch the multifunction cards from getting recognized by the 8250_pci? Having pci_timedia_init() return an error keeps the patch small, but a purist may prefer just filling out the table entries.

3) Anyone have Timedia PCI cards (serial only, parallel only, multifunction), that I could gather some info for?

Thanks for reading through this. Since I'm doing this, I'd rather get it "right".

Rob Currey
avalonforest @ centurytel.net

Just FYI ... (and future googlers)

00:09.0 Serial controller: Timedia Technology Co Ltd PCI2S550 (Dual 16550 UART) (rev 01) (prog-if 02 [16550])
Subsystem: Timedia Technology Co Ltd: Unknown device 4089
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping+ SERR- FastB2B-
Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-

        Interrupt: pin A routed to IRQ 17
        Region 0: I/O ports at 9400 [size=32]
        Region 2: I/O ports at 9000 [size=8]              <==== Parallel
port (external)
        Region 3: I/O ports at 8800 [size=8]              <==== Serial port
(external)
        Region 4: I/O ports at 8400 [size=8]              <==== Parallel
port (internal)
        Region 5: I/O ports at 8000 [size=8]              <==== Serial port

(internal)