Skip to contentSkip to conversation

Class ID limits

LARTC Adam Towarnyckyj 3 participants 5 messages Jun 16, 2004 – Jun 17, 2004

lore
Share & tools
lore
#0 lore raw

Hey everyone,
I had a question about the class id's using the TC command. I'm
using a command that looks something like this:

tc class add dev eth1 parent 10: classid 10:$variable cbq bandwidth 200Mbit rate 512Kbit allot 1514 prio 5 maxburst 20 avpkt 1000 bounded

That's just an example. My problem is I'm guessing the $variable is not allowed to be anything over 9999. I'm getting an error when I run that command with anything over 4 digits as a $variable. The error is:

RTNETLINK answers: Invalid argument

I've also tried just entering that in at the command prompt and using 10000 as the variable and that error shows up.

I actually have a few questions. First, am I right in assuming this or is the reason something totally different? And, if I'm right, is there any way around the limit other than creating a new qdisc? I'm trying to use a number we have set up in our database and sometimes it goes into the 5 digit range. Any help would be greatly appreciated. Thanks!

Adam Towarnyckyj
Network Operations
CommSpeed AZ, LLC
http://www.commspeed.net/
Phone: 928-772-1111 x131

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#1 lore raw
Quoted 9 lines

tc class add dev eth1 parent 10: classid 10:$variable cbq bandwidth 200Mbit rate 512Kbit allot 1514 prio 5 maxburst 20 avpkt 1000 bounded

That's just an example. My problem is I'm guessing the $variable is not allowed to be anything over 9999. I'm getting an error when I run that command with anything over 4 digits as a $variable. The error is:

RTNETLINK answers: Invalid argument

Quoted 8 lines

I've also tried just entering that in at the command prompt and using 10000 as the variable and that error shows up.

I actually have a few questions. First, am I right in assuming this or is the reason something totally different? And, if I'm right, is there any way around the limit other than creating a new qdisc? I'm trying to use a number we have set up in our database and sometimes it goes into the 5 digit range. Any help would be greatly appreciated. Thanks!

Class parameters to tc are hexa numbers so you can use from x:1 to x:ffff, meaning 65535 classes.

Quoted 10 lines

Adam Towarnyckyj
Network Operations
CommSpeed AZ, LLC
http://www.commspeed.net/
Phone: 928-772-1111 x131

Quoted 4 lines

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

---
Catalin(ux aka Dino) BOIE
catab at deuroconsult.ro
http://kernel.umbrella.ro/
_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#2 lore raw
In reply to Adam Towarnyckyj
Quoted 9 lines
Quoted 5 lines

I actually have a few questions. First, am I right in assuming this or is the reason something totally different? And, if I'm right, is there any way around the limit other than creating a new qdisc? I'm trying to use a number we have set up in our database and sometimes it goes into the 5 digit range. Any help would be greatly appreciated. Thanks!

Class parameters to tc are hexa numbers so you can use from x:1 to x:ffff, meaning 65535 classes.

And note that you must supply the classid in hex. Try searching google for a small tool like dec2hex, which converts decimal numbers to hex.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

#4 lore raw
In reply to Adam Towarnyckyj

Thank you very much for your help. I couldn't seem to find that anywhere in the documentation. Maybe I wasn't looking in the right place. Anyways, thanks again.

Adam

-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of Nikolay Datchev
Sent: Thursday, June 17, 2004 12:54 AM
To: Catalin BOIE
Cc: Adam Towarnyckyj; [email protected]
Subject: Re: [LARTC] Class ID limits

Quoted 1 line
Quoted 1 line

I actually have a few questions. First, am I right in assuming this

or

Quoted 1 line
Quoted 1 line

is the reason something totally different? And, if I'm right, is

there

Quoted 1 line
Quoted 1 line

any way around the limit other than creating a new qdisc? I'm trying

to

Quoted 1 line
Quoted 1 line

use a number we have set up in our database and sometimes it goes

into

Quoted 3 lines
Quoted 1 line

the 5 digit range. Any help would be greatly appreciated. Thanks!

Class parameters to tc are hexa numbers so you can use from x:1 to

x:ffff,

Quoted 2 lines

meaning 65535 classes.

And note that you must supply the classid in hex. Try searching google for
a small tool like dec2hex, which converts decimal numbers to hex.

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/

_______________________________________________
LARTC mailing list / [email protected]
http://mailman.ds9a.nl/mailman/listinfo/lartc HOWTO: http://lartc.org/