exynos: arch: add support for exynos5260 SoC
Subsystems (5)
v8 cover exynos: arch: add support for exynos5260 SoC
From: Rahul Sharma <[email protected]>
v8:
1) Removed exynos5260 compatible from mach/exynos5.c
2) Added generic "exynos5" compatible in board and soc dts file.
v7:
1) Renamed board file
V6:
1) Renamed mmc nodes.
2) Removed PHY clocks from DT and put them inside clock driver.
3) Added clock-cells property for all fixed clocks.
4) Removed spdif_ext_clk fixed rate clock.
V5:
1) Removed SYSRAM related code.
2) Fixed mct clocks.
3) Add SoC and Board specifc fixed-rate clocks in respective files.
V4:
1) Removed duplicate MMC Soc property from Board file.
V3:
1) Addressed review comments from Tomasz figa.
V2:
1) Split up DT patch into SoC and Board patch.
This series is based on Kukjin's for-next branch at
http://git.kernel.org/?p=linux/kernel/git/kgene/linux-samsung.git
Pankaj Dubey (1):
ARM: EXYNOS: initial board support for exynos5260 SoC
Rahul Sharma (2):
ARM: dts: add dts files for exynos5260 SoC
ARM: dts: add dts files for xyref5260 board
arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/exynos5260-pinctrl.dtsi | 574 ++++++++++++++++++++++++++++ arch/arm/boot/dts/exynos5260-xyref5260.dts | 103 +++++ arch/arm/boot/dts/exynos5260.dtsi | 304 +++++++++++++++ arch/arm/mach-exynos/Kconfig | 5 + 5 files changed, 987 insertions(+) create mode 100644 arch/arm/boot/dts/exynos5260-pinctrl.dtsi create mode 100644 arch/arm/boot/dts/exynos5260-xyref5260.dts create mode 100644 arch/arm/boot/dts/exynos5260.dtsi
Signature · 1 line
1.7.9.5
PATCH v8 1/3 ARM: EXYNOS: initial board support for exynos5260 SoC
From: Pankaj Dubey <[email protected]>
This patch add basic arch side support for exynos5260 SoC.
Signed-off-by Pankaj Dubey <[email protected]>
Signed-off-by Rahul Sharma <[email protected]>
Reviewed-by Tomasz Figa <[email protected]>
--- arch/arm/mach-exynos/Kconfig | 5 +++++ 1 file changed, 5 insertions(+)
arch/arm/mach-exynos/Kconfig +5 -0
@@ -84,6 +84,11 @@ config SOC_EXYNOS5250 help Enable EXYNOS5250 SoC support +config SOC_EXYNOS5260 + bool "SAMSUNG EXYNOS5260" + default y + depends on ARCH_EXYNOS5 + config SOC_EXYNOS5420 bool "SAMSUNG EXYNOS5420" default y
Signature · 1 line
1.7.9.5
PATCH v8 1/3 ARM: EXYNOS: initial board support for exynos5260 SoC
Hi Rahul,
Quoted 18 lines · Rahul Sharma
From: Pankaj Dubey <[email protected]>
This patch add basic arch side support for exynos5260 SoC.
Signed-off-by Pankaj Dubey <[email protected]>Signed-off-by Rahul Sharma <[email protected]>Reviewed-by Tomasz Figa <[email protected]>--- arch/arm/mach-exynos/Kconfig | 5 +++++ 1 file changed, 5 insertions(+)arch/arm/mach-exynos/Kconfig +0
-0@@ -84,6 +84,11 @@ config SOC_EXYNOS5250 help
arch/arm/mach-exynos/Kconfig config SOC_EXYNOS5250 · line 94
Quoted 10 lines
arch/arm/mach-exynos/Kconfig +5
-0Enable EXYNOS5250 SoC support +config SOC_EXYNOS5260 + bool "SAMSUNG EXYNOS5260" + default y + depends on ARCH_EXYNOS5 + config SOC_EXYNOS5420 bool "SAMSUNG EXYNOS5420" default y
Is this patch necessary now? After Sachin's consolidation series there are no per SoC entries anymore.
Best regards,
Tomasz
PATCH v8 1/3 ARM: EXYNOS: initial board support for exynos5260 SoC
Hi Tomasz,
Quoted 24 lines · Tomasz Figa
Hi Rahul,
Quoted 20 lines · Rahul Sharma
From: Pankaj Dubey <[email protected]>
This patch add basic arch side support for exynos5260 SoC.
Signed-off-by Pankaj Dubey <[email protected]>Signed-off-by Rahul Sharma <[email protected]>Reviewed-by Tomasz Figa <[email protected]>--- arch/arm/mach-exynos/Kconfig | 5 +++++ 1 file changed, 5 insertions(+)arch/arm/mach-exynos/Kconfig +0
-0@@ -84,6 +84,11 @@ config SOC_EXYNOS5250 help Enable EXYNOS5250 SoC support
Quoted 12 lines
arch/arm/mach-exynos/Kconfig config SOC_EXYNOS5250 · line 94
Quoted 9 lines
arch/arm/mach-exynos/Kconfig +5
-0+config SOC_EXYNOS5260 + bool "SAMSUNG EXYNOS5260" + default y + depends on ARCH_EXYNOS5 + config SOC_EXYNOS5420 bool "SAMSUNG EXYNOS5420" default yIs this patch necessary now? After Sachin's consolidation series there are no per SoC entries anymore.
Kukjin still wanted individual SoCs to be selectable. Please refer [1].
[1] http://www.spinics.net/lists/devicetree/msg27040.html
Signature · 2 lines
With warm regards, Sachin
PATCH v8 1/3 ARM: EXYNOS: initial board support for exynos5260 SoC
Quoted 40 lines · Sachin Kamat
Hi Tomasz,
Quoted 24 lines · Tomasz Figa
Hi Rahul,
Quoted 20 lines · Rahul Sharma
From: Pankaj Dubey <[email protected]>
This patch add basic arch side support for exynos5260 SoC.
Signed-off-by Pankaj Dubey <[email protected]>Signed-off-by Rahul Sharma <[email protected]>Reviewed-by Tomasz Figa <[email protected]>--- arch/arm/mach-exynos/Kconfig | 5 +++++ 1 file changed, 5 insertions(+)arch/arm/mach-exynos/Kconfig +0
-0@@ -84,6 +84,11 @@ config SOC_EXYNOS5250 help Enable EXYNOS5250 SoC supportQuoted 12 lines
arch/arm/mach-exynos/Kconfig config SOC_EXYNOS5250 · line 94
Quoted 9 lines
arch/arm/mach-exynos/Kconfig +5
-0+config SOC_EXYNOS5260 + bool "SAMSUNG EXYNOS5260" + default y + depends on ARCH_EXYNOS5 + config SOC_EXYNOS5420 bool "SAMSUNG EXYNOS5420" default yIs this patch necessary now? After Sachin's consolidation series there are no per SoC entries anymore.
Quoted 3 lines
Kukjin still wanted individual SoCs to be selectable. Please refer [1].
I don't think any valid reason was presented there. Features in code should not be selected using #ifdef CONFIG_ anymore, so I don't really see any reason to not proceed with this consolidation. Olof, Arnd?
Best regards,
Tomasz
PATCH v8 1/3 ARM: EXYNOS: initial board support for exynos5260 SoC
Quoted 44 lines · Tomasz Figa
Quoted 12 lines · Sachin Kamat
Hi Tomasz,
Quoted 9 lines · Tomasz Figa
Hi Rahul,
Quoted 5 lines · Rahul Sharma
From: Pankaj Dubey <[email protected]>
This patch add basic arch side support for exynos5260 SoC.
Quoted 8 lines
Quoted 8 lines
arch/arm/mach-
Quoted 8 lines
Signed-off-by Pankaj Dubey <[email protected]>Signed-off-by Rahul Sharma <[email protected]>Reviewed-by Tomasz Figa <[email protected]>--- arch/arm/mach-exynos/Kconfig | 5 +++++ 1 file changed, 5 insertions(+)arch/arm/mach- renamed from arch/arm/mach-exynos/Kconfig +0
-0exynos/Kconfig
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
index fc8bf18..bf4ed87 100644
arch/arm/mach-exynos/Kconfig +0
-0@@ -84,6 +84,11 @@ config SOC_EXYNOS5250 help Enable EXYNOS5250 SoC supportQuoted 11 lines
Quoted 11 lines
arch/arm/mach-exynos/Kconfig config SOC_EXYNOS5250 · line 94
Quoted 9 lines
arch/arm/mach-exynos/Kconfig +5
-0+config SOC_EXYNOS5260 + bool "SAMSUNG EXYNOS5260" + default y + depends on ARCH_EXYNOS5 + config SOC_EXYNOS5420 bool "SAMSUNG EXYNOS5420" default yIs this patch necessary now? After Sachin's consolidation series there
are
Quoted 2 lines
Quoted 1 line
no per SoC entries anymore.
Quoted 8 lines
Quoted 3 lines
Kukjin still wanted individual SoCs to be selectable. Please refer [1].
I don't think any valid reason was presented there. Features in code should not be selected using #ifdef
CONFIG_anymore, so I don't really see any reason to not proceed with this consolidation. Olof, Arnd?
Hi,
Yeah, in this case, nothing happened with adding SOC_EXYNOS5260. So I don't have any idea why this is required.
- Kukjin
PATCH v8 1/3 ARM: EXYNOS: initial board support for exynos5260 SoC
Hi Kukjin,
Need this macro to enable build for clock driver.
Regards,
Rahul Sharma.
Quoted 59 lines · Kukjin Kim
Quoted 44 lines · Tomasz Figa
Quoted 12 lines · Sachin Kamat
Hi Tomasz,
Quoted 9 lines · Tomasz Figa
Hi Rahul,
Quoted 5 lines · Rahul Sharma
From: Pankaj Dubey <[email protected]>
This patch add basic arch side support for exynos5260 SoC.
Quoted 8 lines
Quoted 8 lines
arch/arm/mach-
Quoted 8 lines
Signed-off-by Pankaj Dubey <[email protected]>Signed-off-by Rahul Sharma <[email protected]>Reviewed-by Tomasz Figa <[email protected]>--- arch/arm/mach-exynos/Kconfig | 5 +++++ 1 file changed, 5 insertions(+)arch/arm/mach- renamed from arch/arm/mach-exynos/Kconfig +0
-0exynos/Kconfig
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
index fc8bf18..bf4ed87 100644
arch/arm/mach-exynos/Kconfig +0
-0@@ -84,6 +84,11 @@ config SOC_EXYNOS5250 help Enable EXYNOS5250 SoC supportQuoted 11 lines
Quoted 11 lines
arch/arm/mach-exynos/Kconfig config SOC_EXYNOS5250 · line 94
Quoted 9 lines
arch/arm/mach-exynos/Kconfig +5
-0+config SOC_EXYNOS5260 + bool "SAMSUNG EXYNOS5260" + default y + depends on ARCH_EXYNOS5 + config SOC_EXYNOS5420 bool "SAMSUNG EXYNOS5420" default yIs this patch necessary now? After Sachin's consolidation series there
are
Quoted 2 lines
Quoted 1 line
no per SoC entries anymore.
Quoted 8 lines
Quoted 3 lines
Kukjin still wanted individual SoCs to be selectable. Please refer [1].
I don't think any valid reason was presented there. Features in code should not be selected using #ifdef
CONFIG_anymore, so I don't really see any reason to not proceed with this consolidation. Olof, Arnd?Hi,
Yeah, in this case, nothing happened with adding
SOC_EXYNOS5260. So I don't have any idea why this is required.- Kukjin
PATCH v8 1/3 ARM: EXYNOS: initial board support for exynos5260 SoC
Quoted 3 lines · Rahul Sharma
Hi Kukjin,
Hi,
Quoted 2 lines
Need this macro to enable build for clock driver.
I found it in your patch, "clk/exynos5260: add clock file for exynos5260". For consistency, I'm fine on this, if Tomasz has no objection me to pick this into samsung tree for the 5260 clock stuff "drivers/clk/samsung/Makefile".
Thanks,
Kukjin
Quoted 67 lines
Regards,
Rahul Sharma.Quoted 31 lines · Kukjin Kim
Quoted 30 lines · Tomasz Figa
Quoted 12 lines · Sachin Kamat
Hi Tomasz,
Quoted 9 lines · Tomasz Figa
Hi Rahul,
Quoted 5 lines · Rahul Sharma
From: Pankaj Dubey <[email protected]>
This patch add basic arch side support for exynos5260 SoC.
Quoted 8 lines
Quoted 8 lines
arch/arm/mach-
Quoted 8 lines
Signed-off-by Pankaj Dubey <[email protected]>Signed-off-by Rahul Sharma <[email protected]>Reviewed-by Tomasz Figa <[email protected]>--- arch/arm/mach-exynos/Kconfig | 5 +++++ 1 file changed, 5 insertions(+)arch/arm/mach- renamed from arch/arm/mach-exynos/Kconfig +0
-0exynos/Kconfig
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
index fc8bf18..bf4ed87 100644
arch/arm/mach-exynos/Kconfig +0
-0@@ -84,6 +84,11 @@ config SOC_EXYNOS5250 help Enable EXYNOS5250 SoC supportQuoted 11 lines
Quoted 11 lines
Quoted 11 lines
Quoted 11 lines
arch/arm/mach-exynos/Kconfig config SOC_EXYNOS5250 · line 94
Quoted 9 lines
arch/arm/mach-exynos/Kconfig +5
-0+config SOC_EXYNOS5260 + bool "SAMSUNG EXYNOS5260" + default y + depends on ARCH_EXYNOS5 + config SOC_EXYNOS5420 bool "SAMSUNG EXYNOS5420" default yIs this patch necessary now? After Sachin's consolidation series
there
Quoted 4 lines
Quoted 4 lines
are
Quoted 3 lines
Quoted 1 line
no per SoC entries anymore.
Kukjin still wanted individual SoCs to be selectable. Please refer
[1].
Quoted 10 lines
Quoted 7 lines
Quoted 2 lines
I don't think any valid reason was presented there. Features in code should not be selected using #ifdef
CONFIG_anymore, so I don't really see any reason to not proceed with this consolidation. Olof, Arnd?Hi,
Yeah, in this case, nothing happened with adding
SOC_EXYNOS5260. So Idon't have any idea why this is required.
Quoted 3 lines
- Kukjin
PATCH v8 1/3 ARM: EXYNOS: initial board support for exynos5260 SoC
Hi Tomasz,
Please share your opinion.
Regards,
Rahul Sharma
Quoted 84 lines · Kukjin Kim
Quoted 3 lines · Rahul Sharma
Hi Kukjin,
Hi,
Quoted 2 lines
Need this macro to enable build for clock driver.
I found it in your patch, "clk/exynos5260: add clock file for exynos5260". For consistency, I'm fine on this, if Tomasz has no objection me to pick this into samsung tree for the 5260 clock stuff "
drivers/clk/samsung/Makefile".Thanks,
KukjinQuoted 67 lines
Regards,
Rahul Sharma.Quoted 31 lines · Kukjin Kim
Quoted 30 lines · Tomasz Figa
Quoted 12 lines · Sachin Kamat
Hi Tomasz,
Quoted 9 lines · Tomasz Figa
Hi Rahul,
Quoted 5 lines · Rahul Sharma
From: Pankaj Dubey <[email protected]>
This patch add basic arch side support for exynos5260 SoC.
Quoted 8 lines
Quoted 8 lines
arch/arm/mach-
Quoted 8 lines
Signed-off-by Pankaj Dubey <[email protected]>Signed-off-by Rahul Sharma <[email protected]>Reviewed-by Tomasz Figa <[email protected]>--- arch/arm/mach-exynos/Kconfig | 5 +++++ 1 file changed, 5 insertions(+)arch/arm/mach- renamed from arch/arm/mach-exynos/Kconfig +0
-0exynos/Kconfig
Quoted 7 lines
Quoted 7 lines
Quoted 7 lines
index fc8bf18..bf4ed87 100644
arch/arm/mach-exynos/Kconfig +0
-0@@ -84,6 +84,11 @@ config SOC_EXYNOS5250 help Enable EXYNOS5250 SoC supportQuoted 11 lines
Quoted 11 lines
Quoted 11 lines
Quoted 11 lines
arch/arm/mach-exynos/Kconfig config SOC_EXYNOS5250 · line 94
Quoted 9 lines
arch/arm/mach-exynos/Kconfig +5
-0+config SOC_EXYNOS5260 + bool "SAMSUNG EXYNOS5260" + default y + depends on ARCH_EXYNOS5 + config SOC_EXYNOS5420 bool "SAMSUNG EXYNOS5420" default yIs this patch necessary now? After Sachin's consolidation series
there
Quoted 4 lines
Quoted 4 lines
are
Quoted 3 lines
Quoted 1 line
no per SoC entries anymore.
Kukjin still wanted individual SoCs to be selectable. Please refer
[1].
Quoted 10 lines
Quoted 7 lines
Quoted 2 lines
I don't think any valid reason was presented there. Features in code should not be selected using #ifdef
CONFIG_anymore, so I don't really see any reason to not proceed with this consolidation. Olof, Arnd?Hi,
Yeah, in this case, nothing happened with adding
SOC_EXYNOS5260. So Idon't have any idea why this is required.
Quoted 3 lines
- Kukjin
PATCH v8 1/3 ARM: EXYNOS: initial board support for exynos5260 SoC
In reply to Kukjin KimHi Kukjin,
Quoted 4 lines · Kukjin Kim
Quoted 3 lines · Rahul Sharma
Hi Kukjin,
Quoted 8 lines
Hi,
Quoted 2 lines
Need this macro to enable build for clock driver.
I found it in your patch, "clk/exynos5260: add clock file for exynos5260". For consistency, I'm fine on this, if Tomasz has no objection me to pick this into samsung tree for the 5260 clock stuff "
drivers/clk/samsung/Makefile".
Yes, this should go through Samsung tree, but let me prepare a branch for you to pull from with all the necessary dependencies.
Best regards,
Tomasz
PATCH v8 2/3 ARM: dts: add dts files for exynos5260 SoC
In reply to Rahul SharmaThe patch adds the dts files for exynos5260.
Signed-off-by Pankaj Dubey <[email protected]>
Signed-off-by Rahul Sharma <[email protected]>
Signed-off-by Arun Kumar K <[email protected]>
Reviewed-by Tomasz Figa <[email protected]>
--- arch/arm/boot/dts/exynos5260-pinctrl.dtsi | 574 +++++++++++++++++++++++++++++ arch/arm/boot/dts/exynos5260.dtsi | 304 +++++++++++++++ 2 files changed, 878 insertions(+) create mode 100644 arch/arm/boot/dts/exynos5260-pinctrl.dtsi create mode 100644 arch/arm/boot/dts/exynos5260.dtsi
arch/arm/boot/dts/exynos5260-pinctrl.dtsi new file +574 -0
@@ -0,0 +1,574 @@ +/* + * Samsung's Exynos5260 SoC pin-mux and pin-config device tree source + * + * Copyright (c) 2013 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * Samsung's Exynos5260 SoC pin-mux and pin-config options are listed as device + * tree nodes are listed in this file. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#define PIN_PULL_NONE 0 +#define PIN_PULL_DOWN 1 +#define PIN_PULL_UP 3 + +&pinctrl_0 { + gpa0: gpa0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpa1: gpa1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpa2: gpa2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb0: gpb0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb1: gpb1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb2: gpb2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb3: gpb3 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb4: gpb4 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb5: gpb5 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpd0: gpd0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpd1: gpd1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpd2: gpd2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpe0: gpe0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpe1: gpe1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpf0: gpf0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpf1: gpf1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpk0: gpk0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpx0: gpx0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpx1: gpx1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpx2: gpx2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpx3: gpx3 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + uart0_data: uart0-data { + samsung,pins = "gpa0-0", "gpa0-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + uart0_fctl: uart0-fctl { + samsung,pins = "gpa0-2", "gpa0-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + uart1_data: uart1-data { + samsung,pins = "gpa1-0", "gpa1-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + uart1_fctl: uart1-fctl { + samsung,pins = "gpa1-2", "gpa1-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + uart2_data: uart2-data { + samsung,pins = "gpa1-4", "gpa1-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + spi0_bus: spi0-bus { + samsung,pins = "gpa2-0", "gpa2-2", "gpa2-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + spi1_bus: spi1-bus { + samsung,pins = "gpa2-4", "gpa2-6", "gpa2-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + usb3_vbus0_en: usb3-vbus0-en { + samsung,pins = "gpa2-4"; + samsung,pin-function = <1>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + i2s1_bus: i2s1-bus { + samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3", + "gpb0-4"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + pcm1_bus: pcm1-bus { + samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3", + "gpb0-4"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + spdif1_bus: spdif1-bus { + samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2"; + samsung,pin-function = <4>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + spi2_bus: spi2-bus { + samsung,pins = "gpb1-0", "gpb1-2", "gpb1-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c0_hs_bus: i2c0-hs-bus { + samsung,pins = "gpb3-0", "gpb3-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c1_hs_bus: i2c1-hs-bus { + samsung,pins = "gpb3-2", "gpb3-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c2_hs_bus: i2c2-hs-bus { + samsung,pins = "gpb3-4", "gpb3-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c3_hs_bus: i2c3-hs-bus { + samsung,pins = "gpb3-6", "gpb3-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c4_bus: i2c4-bus { + samsung,pins = "gpb4-0", "gpb4-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c5_bus: i2c5-bus { + samsung,pins = "gpb4-2", "gpb4-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c6_bus: i2c6-bus { + samsung,pins = "gpb4-4", "gpb4-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c7_bus: i2c7-bus { + samsung,pins = "gpb4-6", "gpb4-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c8_bus: i2c8-bus { + samsung,pins = "gpb5-0", "gpb5-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c9_bus: i2c9-bus { + samsung,pins = "gpb5-2", "gpb5-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c10_bus: i2c10-bus { + samsung,pins = "gpb5-4", "gpb5-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c11_bus: i2c11-bus { + samsung,pins = "gpb5-6", "gpb5-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + cam_gpio_a: cam-gpio-a { + samsung,pins = "gpe0-0", "gpe0-1", "gpe0-2", "gpe0-3", + "gpe0-4", "gpe0-5", "gpe0-6", "gpe0-7", + "gpe1-0", "gpe1-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + cam_gpio_b: cam-gpio-b { + samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3", + "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + cam_i2c1_bus: cam-i2c1-bus { + samsung,pins = "gpf0-2", "gpf0-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + cam_i2c0_bus: cam-i2c0-bus { + samsung,pins = "gpf0-0", "gpf0-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + cam_spi0_bus: cam-spi0-bus { + samsung,pins = "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + cam_spi1_bus: cam-spi1-bus { + samsung,pins = "gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; +}; + +&pinctrl_1 { + gpc0: gpc0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpc1: gpc1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpc2: gpc2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpc3: gpc3 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpc4: gpc4 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + sd0_clk: sd0-clk { + samsung,pins = "gpc0-0"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd0_cmd: sd0-cmd { + samsung,pins = "gpc0-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd0_bus1: sd0-bus-width1 { + samsung,pins = "gpc0-2"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd0_bus4: sd0-bus-width4 { + samsung,pins = "gpc0-3", "gpc0-4", "gpc0-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd0_bus8: sd0-bus-width8 { + samsung,pins = "gpc3-0", "gpc3-1", "gpc3-2", "gpc3-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd0_rdqs: sd0-rdqs { + samsung,pins = "gpc0-6"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd1_clk: sd1-clk { + samsung,pins = "gpc1-0"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd1_cmd: sd1-cmd { + samsung,pins = "gpc1-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd1_bus1: sd1-bus-width1 { + samsung,pins = "gpc1-2"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd1_bus4: sd1-bus-width4 { + samsung,pins = "gpc1-3", "gpc1-4", "gpc1-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd1_bus8: sd1-bus-width8 { + samsung,pins = "gpc4-0", "gpc4-1", "gpc4-2", "gpc4-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd2_clk: sd2-clk { + samsung,pins = "gpc2-0"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd2_cmd: sd2-cmd { + samsung,pins = "gpc2-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd2_cd: sd2-cd { + samsung,pins = "gpc2-2"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd2_bus1: sd2-bus-width1 { + samsung,pins = "gpc2-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd2_bus4: sd2-bus-width4 { + samsung,pins = "gpc2-4", "gpc2-5", "gpc2-6"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; +}; + +&pinctrl_2 { + gpz0: gpz0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpz1: gpz1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; +};
arch/arm/boot/dts/exynos5260.dtsi new file +304 -0
304 lines not on this page · raw message
Signature · 1 line
1.7.9.5
PATCH v8 2/3 ARM: dts: add dts files for exynos5260 SoC
Quoted 7 lines · Rahul Sharma
The patch adds the dts files for exynos5260.
Signed-off-by Pankaj Dubey <[email protected]>Signed-off-by Rahul Sharma <[email protected]>Signed-off-by Arun Kumar K <[email protected]>Reviewed-by Tomasz Figa <[email protected]>
Looks good to me. I will queue this 5260 SoC dtsi and 3rd xyref5260 board dt for 3.6 and I hope I can send this series with other multi-platform for exynos in this time ;-)
Thanks,
Kukjin
Quoted 745 lines
--- arch/arm/boot/dts/exynos5260-pinctrl.dtsi | 574 +++++++++++++++++++++++++++++ arch/arm/boot/dts/exynos5260.dtsi | 304 +++++++++++++++ 2 files changed, 878 insertions(+) create mode 100644 arch/arm/boot/dts/exynos5260-pinctrl.dtsi create mode 100644 arch/arm/boot/dts/exynos5260.dtsiarch/arm/boot/dts/exynos5260-pinctrl.dtsi new file +7
-0@@ -0,0 +1,574 @@ +/* + * Samsung's Exynos5260 SoC pin-mux and pin-config device tree source + * + * Copyright (c) 2013 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * Samsung's Exynos5260 SoC pin-mux and pin-config options are listed asdevice
+ * tree nodes are listed in this file.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.arch/arm/boot/dts/exynos5260-pinctrl.dtsi new file +562
-0+*/ + +#define PIN_PULL_NONE 0 +#define PIN_PULL_DOWN 1 +#define PIN_PULL_UP 3 + +&pinctrl_0 { + gpa0: gpa0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpa1: gpa1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpa2: gpa2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb0: gpb0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb1: gpb1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb2: gpb2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb3: gpb3 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb4: gpb4 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpb5: gpb5 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpd0: gpd0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpd1: gpd1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpd2: gpd2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpe0: gpe0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpe1: gpe1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpf0: gpf0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpf1: gpf1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpk0: gpk0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpx0: gpx0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpx1: gpx1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpx2: gpx2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpx3: gpx3 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + uart0_data: uart0-data { + samsung,pins = "gpa0-0", "gpa0-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + uart0_fctl: uart0-fctl { + samsung,pins = "gpa0-2", "gpa0-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + uart1_data: uart1-data { + samsung,pins = "gpa1-0", "gpa1-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + uart1_fctl: uart1-fctl { + samsung,pins = "gpa1-2", "gpa1-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + uart2_data: uart2-data { + samsung,pins = "gpa1-4", "gpa1-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + spi0_bus: spi0-bus { + samsung,pins = "gpa2-0", "gpa2-2", "gpa2-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + spi1_bus: spi1-bus { + samsung,pins = "gpa2-4", "gpa2-6", "gpa2-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + usb3_vbus0_en: usb3-vbus0-en { + samsung,pins = "gpa2-4"; + samsung,pin-function = <1>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + i2s1_bus: i2s1-bus { + samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3", + "gpb0-4"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + pcm1_bus: pcm1-bus { + samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2", "gpb0-3", + "gpb0-4"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + spdif1_bus: spdif1-bus { + samsung,pins = "gpb0-0", "gpb0-1", "gpb0-2"; + samsung,pin-function = <4>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + spi2_bus: spi2-bus { + samsung,pins = "gpb1-0", "gpb1-2", "gpb1-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c0_hs_bus: i2c0-hs-bus { + samsung,pins = "gpb3-0", "gpb3-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c1_hs_bus: i2c1-hs-bus { + samsung,pins = "gpb3-2", "gpb3-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c2_hs_bus: i2c2-hs-bus { + samsung,pins = "gpb3-4", "gpb3-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c3_hs_bus: i2c3-hs-bus { + samsung,pins = "gpb3-6", "gpb3-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c4_bus: i2c4-bus { + samsung,pins = "gpb4-0", "gpb4-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c5_bus: i2c5-bus { + samsung,pins = "gpb4-2", "gpb4-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c6_bus: i2c6-bus { + samsung,pins = "gpb4-4", "gpb4-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c7_bus: i2c7-bus { + samsung,pins = "gpb4-6", "gpb4-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c8_bus: i2c8-bus { + samsung,pins = "gpb5-0", "gpb5-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c9_bus: i2c9-bus { + samsung,pins = "gpb5-2", "gpb5-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c10_bus: i2c10-bus { + samsung,pins = "gpb5-4", "gpb5-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + i2c11_bus: i2c11-bus { + samsung,pins = "gpb5-6", "gpb5-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + cam_gpio_a: cam-gpio-a { + samsung,pins = "gpe0-0", "gpe0-1", "gpe0-2", "gpe0-3", + "gpe0-4", "gpe0-5", "gpe0-6", "gpe0-7", + "gpe1-0", "gpe1-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + cam_gpio_b: cam-gpio-b { + samsung,pins = "gpf0-0", "gpf0-1", "gpf0-2", "gpf0-3", + "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3"; + samsung,pin-function = <3>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + cam_i2c1_bus: cam-i2c1-bus { + samsung,pins = "gpf0-2", "gpf0-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + cam_i2c0_bus: cam-i2c0-bus { + samsung,pins = "gpf0-0", "gpf0-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <0>; + }; + + cam_spi0_bus: cam-spi0-bus { + samsung,pins = "gpf1-0", "gpf1-1", "gpf1-2", "gpf1-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; + + cam_spi1_bus: cam-spi1-bus { + samsung,pins = "gpf1-4", "gpf1-5", "gpf1-6", "gpf1-7"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <0>; + }; +}; + +&pinctrl_1 { + gpc0: gpc0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpc1: gpc1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpc2: gpc2 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpc3: gpc3 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpc4: gpc4 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + sd0_clk: sd0-clk { + samsung,pins = "gpc0-0"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd0_cmd: sd0-cmd { + samsung,pins = "gpc0-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd0_bus1: sd0-bus-width1 { + samsung,pins = "gpc0-2"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd0_bus4: sd0-bus-width4 { + samsung,pins = "gpc0-3", "gpc0-4", "gpc0-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd0_bus8: sd0-bus-width8 { + samsung,pins = "gpc3-0", "gpc3-1", "gpc3-2", "gpc3-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd0_rdqs: sd0-rdqs { + samsung,pins = "gpc0-6"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd1_clk: sd1-clk { + samsung,pins = "gpc1-0"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd1_cmd: sd1-cmd { + samsung,pins = "gpc1-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd1_bus1: sd1-bus-width1 { + samsung,pins = "gpc1-2"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd1_bus4: sd1-bus-width4 { + samsung,pins = "gpc1-3", "gpc1-4", "gpc1-5"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd1_bus8: sd1-bus-width8 { + samsung,pins = "gpc4-0", "gpc4-1", "gpc4-2", "gpc4-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd2_clk: sd2-clk { + samsung,pins = "gpc2-0"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd2_cmd: sd2-cmd { + samsung,pins = "gpc2-1"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_NONE>; + samsung,pin-drv = <3>; + }; + + sd2_cd: sd2-cd { + samsung,pins = "gpc2-2"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd2_bus1: sd2-bus-width1 { + samsung,pins = "gpc2-3"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; + + sd2_bus4: sd2-bus-width4 { + samsung,pins = "gpc2-4", "gpc2-5", "gpc2-6"; + samsung,pin-function = <2>; + samsung,pin-pud = <PIN_PULL_UP>; + samsung,pin-drv = <3>; + }; +}; + +&pinctrl_2 { + gpz0: gpz0 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpz1: gpz1 { + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; +};arch/arm/boot/dts/exynos5260.dtsi new file +148
-0@@ -0,0 +1,304 @@ +/* + * SAMSUNG EXYNOS5260 SoC device tree source + * + * Copyright (c) 2013 Samsung Electronics Co., Ltd. + * http://www.samsung.com + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. +*/ + +#include "skeleton.dtsi" + +#include <dt-bindings/clock/exynos5260-clk.h> + +/ { + compatible = "samsung,exynos5260", "samsung,exynos5"; + interrupt-parent = <&gic>; + + aliases { + pinctrl0 = &pinctrl_0; + pinctrl1 = &pinctrl_1; + pinctrl2 = &pinctrl_2; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu at 0 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x0>; + cci-control-port = <&cci_control1>; + }; + + cpu at 1 { + device_type = "cpu"; + compatible = "arm,cortex-a15"; + reg = <0x1>; + cci-control-port = <&cci_control1>; + }; + + cpu at 100 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x100>; + cci-control-port = <&cci_control0>; + }; + + cpu at 101 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x101>; + cci-control-port = <&cci_control0>; + }; + + cpu at 102 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x102>; + cci-control-port = <&cci_control0>; + }; + + cpu at 103 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0x103>; + cci-control-port = <&cci_control0>; + }; + }; + + soc: soc { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + clock_top: clock-controller at 10010000 { + compatible = "samsung,exynos5260-clock-top"; + reg = <0x10010000 0x10000>; + #clock-cells = <1>; + }; + + clock_peri: clock-controller at 10200000 { + compatible = "samsung,exynos5260-clock-peri"; + reg = <0x10200000 0x10000>; + #clock-cells = <1>; + }; + + clock_egl: clock-controller at 10600000 { + compatible = "samsung,exynos5260-clock-egl"; + reg = <0x10600000 0x10000>; + #clock-cells = <1>; + }; + + clock_kfc: clock-controller at 10700000 { + compatible = "samsung,exynos5260-clock-kfc"; + reg = <0x10700000 0x10000>; + #clock-cells = <1>; + }; + + clock_g2d: clock-controller at 10A00000 { + compatible = "samsung,exynos5260-clock-g2d"; + reg = <0x10A00000 0x10000>; + #clock-cells = <1>; + }; + + clock_mif: clock-controller at 10CE0000 { + compatible = "samsung,exynos5260-clock-mif"; + reg = <0x10CE0000 0x10000>; + #clock-cells = <1>; + }; + + clock_mfc: clock-controller at 11090000 { + compatible = "samsung,exynos5260-clock-mfc"; + reg = <0x11090000 0x10000>; + #clock-cells = <1>; + }; + + clock_g3d: clock-controller at 11830000 { + compatible = "samsung,exynos5260-clock-g3d"; + reg = <0x11830000 0x10000>; + #clock-cells = <1>; + }; + + clock_fsys: clock-controller at 122E0000 { + compatible = "samsung,exynos5260-clock-fsys"; + reg = <0x122E0000 0x10000>; + #clock-cells = <1>; + }; + + clock_aud: clock-controller at 128C0000 { + compatible = "samsung,exynos5260-clock-aud"; + reg = <0x128C0000 0x10000>; + #clock-cells = <1>; + }; + + clock_isp: clock-controller at 133C0000 { + compatible = "samsung,exynos5260-clock-isp"; + reg = <0x133C0000 0x10000>; + #clock-cells = <1>; + }; + + clock_gscl: clock-controller at 13F00000 { + compatible = "samsung,exynos5260-clock-gscl"; + reg = <0x13F00000 0x10000>; + #clock-cells = <1>;
arch/arm/boot/dts/exynos5260.dtsi line 158
Quoted 10 lines
arch/arm/boot/dts/exynos5260.dtsi new file +10
-0+ }; + + clock_disp: clock-controller at 14550000 { + compatible = "samsung,exynos5260-clock-disp"; + reg = <0x14550000 0x10000>; + #clock-cells = <1>; + }; + + gic: interrupt-controller at 10481000 { + compatible = "arm,cortex-a15-gic",
"arm,cortex-a9-gic";
Quoted 44 lines
arch/arm/boot/dts/exynos5260.dtsi new file +44
-0+ #interrupt-cells = <3>; + #address-cells = <0>; + #size-cells = <0>; + interrupt-controller; + reg = <0x10481000 0x1000>, + <0x10482000 0x1000>, + <0x10484000 0x2000>, + <0x10486000 0x2000>; + interrupts = <1 9 0xf04>; + }; + + chipid: chipid at 10000000 { + compatible = "samsung,exynos4210-chipid"; + reg = <0x10000000 0x100>; + }; + + mct: mct at 100B0000 { + compatible = "samsung,exynos4210-mct"; + reg = <0x100B0000 0x1000>; + clocks = <&fin_pll>, <&clock_peri PERI_CLK_MCT>; + clock-names = "fin_pll", "mct"; + interrupts = <0 104 0>, <0 105 0>, <0 106 0>, + <0 107 0>, <0 122 0>, <0 123 0>, + <0 124 0>, <0 125 0>, <0 126 0>, + <0 127 0>, <0 128 0>, <0 129 0>; + }; + + cci: cci at 10F00000 { + compatible = "arm,cci-400"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x10F00000 0x1000>; + ranges = <0x0 0x10F00000 0x6000>; + + cci_control0: slave-if at 4000 { + compatible = "arm,cci-400-ctrl-if"; + interface-type = "ace"; + reg = <0x4000 0x1000>; + }; + + cci_control1: slave-if at 5000 { + compatible = "arm,cci-400-ctrl-if"; + interface-type = "ace"; + reg = <0x5000 0x1000>;
arch/arm/boot/dts/exynos5260.dtsi
Quoted 10 lines
arch/arm/boot/dts/exynos5260.dtsi new file +10
-0+ }; + }; + + pinctrl_0: pinctrl at 11600000 { + compatible = "samsung,exynos5260-pinctrl"; + reg = <0x11600000 0x1000>; + interrupts = <0 79 0>; + + wakeup-interrupt-controller { + compatible =
"samsung,exynos4210-wakeup-eint";
Quoted 101 lines
arch/arm/boot/dts/exynos5260.dtsi new file +22
-0+ interrupt-parent = <&gic>; + interrupts = <0 32 0>; + }; + }; + + pinctrl_1: pinctrl at 12290000 { + compatible = "samsung,exynos5260-pinctrl"; + reg = <0x12290000 0x1000>; + interrupts = <0 157 0>; + }; + + pinctrl_2: pinctrl at 128B0000 { + compatible = "samsung,exynos5260-pinctrl"; + reg = <0x128B0000 0x1000>; + interrupts = <0 243 0>; + }; + + uart0: serial at 12C00000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C00000 0x100>; + interrupts = <0 146 0>; + clocks = <&clock_peri PERI_CLK_UART0>, <&clock_peri
PERI_SCLK_UART0>;arch/arm/boot/dts/exynos5260.dtsi new file +9
-0+ clock-names = "uart", "clk_uart_baud0"; + status = "disabled"; + }; + + uart1: serial at 12C10000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C10000 0x100>; + interrupts = <0 147 0>; + clocks = <&clock_peri PERI_CLK_UART1>, <&clock_peri
PERI_SCLK_UART1>;arch/arm/boot/dts/exynos5260.dtsi new file +9
-0+ clock-names = "uart", "clk_uart_baud0"; + status = "disabled"; + }; + + uart2: serial at 12C20000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12C20000 0x100>; + interrupts = <0 148 0>; + clocks = <&clock_peri PERI_CLK_UART2>, <&clock_peri
PERI_SCLK_UART2>;arch/arm/boot/dts/exynos5260.dtsi new file +9
-0+ clock-names = "uart", "clk_uart_baud0"; + status = "disabled"; + }; + + uart3: serial at 12860000 { + compatible = "samsung,exynos4210-uart"; + reg = <0x12860000 0x100>; + interrupts = <0 145 0>; + clocks = <&clock_aud AUD_CLK_AUD_UART>, <&clock_aud
AUD_SCLK_AUD_UART>;arch/arm/boot/dts/exynos5260.dtsi new file +11
-0+ clock-names = "uart", "clk_uart_baud0"; + status = "disabled"; + }; + + mmc_0: mmc at 12140000 { + compatible = "samsung,exynos5250-dw-mshc"; + reg = <0x12140000 0x2000>; + interrupts = <0 156 0>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clock_fsys FSYS_CLK_MMC0>, <&clock_top
TOP_SCLK_MMC0>;arch/arm/boot/dts/exynos5260.dtsi new file +12
-0+ clock-names = "biu", "ciu"; + fifo-depth = <64>; + status = "disabled"; + }; + + mmc_1: mmc at 12150000 { + compatible = "samsung,exynos5250-dw-mshc"; + reg = <0x12150000 0x2000>; + interrupts = <0 158 0>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clock_fsys FSYS_CLK_MMC1>, <&clock_top
TOP_SCLK_MMC1>;arch/arm/boot/dts/exynos5260.dtsi new file +12
-0+ clock-names = "biu", "ciu"; + fifo-depth = <64>; + status = "disabled"; + }; + + mmc_2: mmc at 12160000 { + compatible = "samsung,exynos5250-dw-mshc"; + reg = <0x12160000 0x2000>; + interrupts = <0 159 0>; + #address-cells = <1>; + #size-cells = <0>; + clocks = <&clock_fsys FSYS_CLK_MMC2>, <&clock_top
TOP_SCLK_MMC2>;arch/arm/boot/dts/exynos5260.dtsi new file +8
-1+ clock-names = "biu", "ciu"; + fifo-depth = <64>; + status = "disabled"; + }; + }; +}; + +#include "exynos5260-pinctrl.dtsi" --1.7.9.5
PATCH v8 3/3 ARM: dts: add dts files for xyref5260 board
In reply to Rahul SharmaThe patch adds the dts files for xyref5260 board which is based on Exynos5260 Evt0 sample.
Signed-off-by Rahul Sharma <[email protected]>
--- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/exynos5260-xyref5260.dts | 103 ++++++++++++++++++++++++++++ 2 files changed, 104 insertions(+) create mode 100644 arch/arm/boot/dts/exynos5260-xyref5260.dts
arch/arm/boot/dts/Makefile +1 -0
@@ -73,6 +73,7 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \ exynos5250-arndale.dtb \ exynos5250-smdk5250.dtb \ exynos5250-snow.dtb \ + exynos5260-xyref5260.dtb \ exynos5420-arndale-octa.dtb \ exynos5420-smdk5420.dtb \ exynos5440-sd5v1.dtb \
arch/arm/boot/dts/exynos5260-xyref5260.dts new file +103 -0
103 lines not on this page · raw message
Signature · 1 line
1.7.9.5
v8 cover exynos: arch: add support for exynos5260 SoC
In reply to Rahul SharmaHi Rahul,
Quoted 39 lines · Rahul Sharma
From: Rahul Sharma <[email protected]>
v8:
1) Removed exynos5260 compatible frommach/exynos5.c
2) Added generic "exynos5" compatible in board and soc dts file.v7:
1) Renamed board fileV6:
1) Renamed mmc nodes.
2) Removed PHY clocks from DT and put them inside clock driver.
3) Added clock-cells property for all fixed clocks.
4) Removedspdif_ext_clkfixed rate clock.V5:
1) Removed SYSRAM related code.
2) Fixed mct clocks.
3) Add SoC and Board specifc fixed-rate clocks in respective files.V4:
1) Removed duplicate MMC Soc property from Board file.V3:
1) Addressed review comments from Tomasz figa.V2:
1) Split up DT patch into SoC and Board patch.This series is based on Kukjin's for-next branch at
http://git.kernel.org/?p=linux/kernel/git/kgene/linux-samsung.gitPankaj Dubey (1):
ARM: EXYNOS: initial board support for exynos5260 SoCRahul Sharma (2):
ARM: dts: add dts files for exynos5260 SoC
ARM: dts: add dts files for xyref5260 board
Quoted 9 lines
arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/exynos5260-pinctrl.dtsi | 574 ++++++++++++++++++++++++++++ arch/arm/boot/dts/exynos5260-xyref5260.dts | 103 +++++ arch/arm/boot/dts/exynos5260.dtsi | 304 +++++++++++++++ arch/arm/mach-exynos/Kconfig | 5 + 5 files changed, 987 insertions(+) create mode 100644 arch/arm/boot/dts/exynos5260-pinctrl.dtsi create mode 100644 arch/arm/boot/dts/exynos5260-xyref5260.dts create mode 100644 arch/arm/boot/dts/exynos5260.dtsi
Series looks good.
Reviewed-by Sachin Kamat <[email protected]>
Signature · 2 lines
With warm regards, Sachin