TC breaking Virtual network connection
Good afternoon,
I am a newbie to lartc. I have read the HOWTO. I set up a CBQ traffic control using the following commands, and it caused my VNC connection to break frequently.
=======================================================================
**CBQ: cbq-1280.My_shaper/sbin/tc qdisc del dev lo root/sbin/tc qdisc add dev lo root handle 1 cbq bandwidth 20Mbps avpkt 1000 cell 8 /sbin/tc class change dev lo root cbq weight 2Mbps allot 1514
/sbin/tc class add dev lo parent 1: classid 1:1280 cbq bandwidth 20Mbps rate 100Kbps weight 10Kbps prio 5 allot 1514 cell 8 maxburst 20 avpkt 1000 bounded /sbin/tc qdisc add dev lo parent 1:1280 handle 1280 tbf rate 100Kbps buffer 10Kb/8 limit 15Kb mtu 1500/sbin/tc filter add dev lo parent 1:0 protocol ip prio 100 u32 match ip dst 192.168.4.0/24 classid 1:1280
========================================================================
I tried deleting the qdisc, but my VNC connection still breaks after i issue this command:
% tc qdisc del dev lo root
What is the correct way to restore to "factory default settings"?
Thanks for reading. Please help me.
Rgds,
Siow Vic
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
hi again,
After i delete the qdisc,
% tc qdisc del dev eth0 root
i display the qdisc status again:
% tc -q qdisc
and nothing is shown. My question is : what is the qdisc algorithm in use if the output is empty.
thanks.
victor
----- Original Message -----
From: Victor Yeo
To: [email protected]
Sent: Thursday, May 05, 2005 2:08 PM
Subject: [LARTC] TC breaking Virtual network connection
Good afternoon,
I am a newbie to lartc. I have read the HOWTO. I set up a CBQ traffic control using the following commands, and it caused my VNC connection to break frequently.
=======================================================================
**CBQ: cbq-1280.My_shaper
/sbin/tc qdisc del dev lo root
/sbin/tc qdisc add dev lo root handle 1 cbq bandwidth 20Mbps avpkt 1000 cell 8 /sbin/tc class change dev lo root cbq weight 2Mbps allot 1514
/sbin/tc class add dev lo parent 1: classid 1:1280 cbq bandwidth 20Mbps rate 100Kbps weight 10Kbps prio 5 allot 1514 cell 8 maxburst 20 avpkt 1000 bounded /sbin/tc qdisc add dev lo parent 1:1280 handle 1280 tbf rate 100Kbps buffer 10Kb/8 limit 15Kb mtu 1500
/sbin/tc filter add dev lo parent 1:0 protocol ip prio 100 u32 match ip dst 192.168.4.0/24 classid 1:1280
========================================================================
I tried deleting the qdisc, but my VNC connection still breaks after i issue this command:
% tc qdisc del dev lo root
What is the correct way to restore to "factory default settings"?
Thanks for reading. Please help me.
Rgds,
Siow Vic
------------------------------------------------------------------------------
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc
_______________________________________________
LARTC mailing list
[email protected]
http://mailman.ds9a.nl/cgi-bin/mailman/listinfo/lartc