usb: dwc3: gadget: Inform system of suspended state
Subsystems (2)
A message that is not in the archive (sent off-list or not yet received): 1b153bce-a66a-45ee-a5c6-963ea6fb1c82.949ef384-8293-46b8-903f-40a477c056ae.c5f44c79-75b2-43c1-a791-806fe8b693cd@emailsignatures365.codetwo.com
PATCH 1/1 usb: dwc3: gadget: Inform system of suspended state
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends DWC3_DEVICE_EVENT_SUSPEND in that case, and not a DWC3_DEVICE_EVENT_DISCONNECT as one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.
Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
---
drivers/usb/dwc3/gadget.c | 1 + 1 file changed, 1 insertion(+)
drivers/usb/dwc3/gadget.c +1 -0
@@ -4343,6 +4343,7 @@ static void dwc3_gadget_suspend_interrupt(struct dwc3 *dwc,if (!dwc->suspended && next ==DWC3_LINK_STATE_U3 ) { dwc->suspended = true;dwc3_suspend_gadget (dwc); +usb_gadget_set_state (dwc->gadget,USB_STATE_SUSPENDED ); } dwc->link_state = next;
Signature · 18 lines
2.34.1 Met vriendelijke groet / kind regards, Mike Looijmans System Expert TOPIC Embedded Products B.V. Materiaalweg 4, 5681 RJ Best The Netherlands T: +31 (0) 499 33 69 69 E: [email protected] W: www.topic.nl Please consider the environment before printing this e-mail
Thinh Nguyen
maintainerHi,
Quoted 10 lines · Mike Looijmans
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends
DWC3_DEVICE_EVENT_SUSPENDin that case, and not aDWC3_DEVICE_EVENT_DISCONNECTas one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
On disconnection, did you see disconnect interrupt? If so, it should transition to USB_STATE_NOATTACHED. This change doesn't seem to directly address your issue. Can you provide the driver tracepoints?
Thanks,
Thinh
Quoted 38 lines
Signed-off-by Mike Looijmans <[email protected]>---
drivers/usb/dwc3/gadget.c | 1 + 1 file changed, 1 insertion(+)drivers/usb/dwc3/gadget.c +1
-0@@ -4343,6 +4343,7 @@ static void dwc3_gadget_suspend_interrupt(struct dwc3 *dwc,if (!dwc->suspended && next ==DWC3_LINK_STATE_U3 ) { dwc->suspended = true;dwc3_suspend_gadget (dwc); +usb_gadget_set_state (dwc->gadget,USB_STATE_SUSPENDED ); } dwc->link_state = next;Signature · 18 lines
2.34.1 Met vriendelijke groet / kind regards, Mike Looijmans System Expert TOPIC Embedded Products B.V. Materiaalweg 4, 5681 RJ Best The Netherlands T: +31 (0) 499 33 69 69 E: [email protected] W: https://urldefense.com/v3/__http://www.topic.nl__;!!A4F2R9G_pg!dXv5bN6_FJRVB7pQogk6ZxPOb97r2m4CJ9R2rvxelfjbfNhJjQ9ilRpqRBgO983Jxof9Hs8f8rY6nX1hyIvD6ZNIwnKmb9c$ Please consider the environment before printing this e-mail
Quoted 10 lines · Thinh Nguyen
Hi,
Quoted 7 lines · Mike Looijmans
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends
DWC3_DEVICE_EVENT_SUSPENDin that case, and not aDWC3_DEVICE_EVENT_DISCONNECTas one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.
Quoted 6 lines
Quoted 3 lines
Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
On disconnection, did you see disconnect interrupt? If so, it should transition to
USB_STATE_NOATTACHED. This change doesn't seem to directly address your issue. Can you provide the driver tracepoints?
The device doesn't issue a disconnect event, I didn't have tracing enabled in the kernel but added some dev_info() calls to determine what was going on. Added this to dwc3_process_event_entry():
dev_info(dwc->dev, "event: 0x%x type=0x%x", event->raw, event->type.type);
When disconnecting the cable from the host, I see this:
[ 50.841411] dwc3 3110000.usb: event: 0x6084 type=0x42 [ 50.841457] dwc3 3110000.usb: event: 0x4086 type=0x43 [ 50.841494] dwc3 3110000.usb: event: 0x6084 type=0x42 [ 50.841534] dwc3 3110000.usb: event: 0x4086 type=0x43 [ 50.841571] dwc3 3110000.usb: event: 0x4086 type=0x43 [ 52.650990] dwc3 3110000.usb: event: 0x30601 type=0x0
The "0x4086" and "0x6084" messages are endpoint events that occur all the time while connected. The last event is the "suspend" one. After that, total silence.
If you need traces, please point me to a description on how to obtain them.
Quoted 29 lines
Thanks,
ThinhQuoted 25 lines
Signed-off-by Mike Looijmans <[email protected]>---
drivers/usb/dwc3/gadget.c | 1 + 1 file changed, 1 insertion(+)drivers/usb/dwc3/gadget.c +1
-0@@ -4343,6 +4343,7 @@ static void dwc3_gadget_suspend_interrupt(struct dwc3 *dwc,if (!dwc->suspended && next ==DWC3_LINK_STATE_U3 ) { dwc->suspended = true;dwc3_suspend_gadget (dwc); +usb_gadget_set_state (dwc->gadget,USB_STATE_SUSPENDED ); } dwc->link_state = next;Signature · 6 lines
2.34.1 Met vriendelijke groet / kind regards, Mike Looijmans
Signature · 10 lines
Mike Looijmans System Expert TOPIC Embedded Products B.V. Materiaalweg 4, 5681 RJ Best The Netherlands T: +31 (0) 499 33 69 69 E: [email protected] W: www.topic.nl
Quoted 31 lines · Mike Looijmans
Quoted 10 lines · Thinh Nguyen
Hi,
Quoted 7 lines · Mike Looijmans
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends
DWC3_DEVICE_EVENT_SUSPENDin that case, and not aDWC3_DEVICE_EVENT_DISCONNECTas one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.Quoted 6 lines
Quoted 3 lines
Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
On disconnection, did you see disconnect interrupt? If so, it should transition to
USB_STATE_NOATTACHED. This change doesn't seem to directly address your issue. Can you provide the driver tracepoints?The device doesn't issue a disconnect event, I didn't have tracing enabled in the kernel but added some
dev_info()calls to determine what was going on. Added this todwc3_process_event_entry():
dev_info(dwc->dev, "event: 0x%x type=0x%x", event->raw, event->type.type);When disconnecting the cable from the host, I see this:
[ 50.841411] dwc3 3110000.usb: event:
0x6084type=0x42 [ 50.841457] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841494] dwc3 3110000.usb: event:0x6084type=0x42 [ 50.841534] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841571] dwc3 3110000.usb: event:0x4086type=0x43 [ 52.650990] dwc3 3110000.usb: event:0x30601type=0x0
Quoted 5 lines
The "
0x4086" and "0x6084" messages are endpoint events that occur all the time while connected. The last event is the "suspend" one. After that, total silence.If you need traces, please point me to a description on how to obtain them.
Hi Mike,
I may be wrong, but can you help understand the mechanism as to how
disconnect interrupt is generated in your targets. For example, on QC SoC's, this happens when HS_PHY_CTRL reg VBUS_VALID bit is cleared and cable is disconnected. This is because the vbus line is not routed to controller. But from my calls with Synopsys previously, I remember that the vbus line is routed to the controller as well for other OEMs. In your SoC, what is the indication to controller that vbus is absent ?
Also, after this happens, do you see the next plug in working ?
Regards,
Krishna,
Quoted 36 lines · Krishna Kurapati PSSNV
Quoted 33 lines · Mike Looijmans
Quoted 10 lines · Thinh Nguyen
Hi,
Quoted 7 lines · Mike Looijmans
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends
DWC3_DEVICE_EVENT_SUSPENDin that case, and not aDWC3_DEVICE_EVENT_DISCONNECTas one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.Quoted 6 lines
Quoted 3 lines
Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
On disconnection, did you see disconnect interrupt? If so, it should transition to
USB_STATE_NOATTACHED. This change doesn't seem to directly address your issue. Can you provide the driver tracepoints?The device doesn't issue a disconnect event, I didn't have tracing enabled in the kernel but added some
dev_info()calls to determine what was going on. Added this todwc3_process_event_entry():
dev_info(dwc->dev, "event: 0x%x type=0x%x", event->raw, event->type.type);When disconnecting the cable from the host, I see this:
[ 50.841411] dwc3 3110000.usb: event:
0x6084type=0x42 [ 50.841457] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841494] dwc3 3110000.usb: event:0x6084type=0x42 [ 50.841534] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841571] dwc3 3110000.usb: event:0x4086type=0x43 [ 52.650990] dwc3 3110000.usb: event:0x30601type=0x0The "
0x4086" and "0x6084" messages are endpoint events that occur all the time while connected. The last event is the "suspend" one. After that, total silence.
Quoted 8 lines
Quoted 3 lines
If you need traces, please point me to a description on how to obtain them.
Hi Mike,
I may be wrong, but can you help understand the mechanism as to how disconnect interrupt is generated in your targets. For example, on QC SoC's, this happens when
HS_PHY_CTRLregVBUS_VALIDbit is cleared and cable is disconnected. This is because the vbus line is not routed to controller. But from my calls with Synopsys previously, I remember that the vbus line is routed to the controller as well for other OEMs. In your SoC, what is the indication to controller that vbus is absent ?
The board I'm testing this on is an LS1028ARDB. Looking at the schematic, VBUS is routed to the chip. There's also an LED attached to it, which turns off when I unplug the cable.
In the devicetree, I can't see any hint of NXP-specific "glue" in the DWC3 entries, so it uses the controller "as is":
compatible = "fsl,ls1028a-dwc3", "snps,dwc3"; reg = <0x0 0x3100000 0x0 0x10000>; snps,dis_rxdet_inp3_quirk; snps,quirk-frame-length-adjustment = <0x20>; snps,incr-burst-type-adjustment = <1>, <4>, <8>, <16>;
The "fsl,ls1028a-dwc3" keyword doesn't actually occur anywhere in the kernel, so it uses plain "snps,dwc3".
Quoted 1 line
Also, after this happens, do you see the next plug in working ?
Next plugin works, because of a "reset" event at that point that makes everything happy again.
The state remains in "configured" while the cable is out. Plugging the cable back in makes it revert to "default" first, then it goes back into "configured".
Signature · 10 lines
Mike Looijmans System Expert TOPIC Embedded Products B.V. Materiaalweg 4, 5681 RJ Best The Netherlands T: +31 (0) 499 33 69 69 E: [email protected] W: www.topic.nl
Quoted 56 lines · Mike Looijmans
Quoted 36 lines · Krishna Kurapati PSSNV
Quoted 33 lines · Mike Looijmans
Quoted 10 lines · Thinh Nguyen
Hi,
Quoted 7 lines · Mike Looijmans
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends
DWC3_DEVICE_EVENT_SUSPENDin that case, and not aDWC3_DEVICE_EVENT_DISCONNECTas one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.Quoted 6 lines
Quoted 3 lines
Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
On disconnection, did you see disconnect interrupt? If so, it should transition to
USB_STATE_NOATTACHED. This change doesn't seem to directly address your issue. Can you provide the driver tracepoints?The device doesn't issue a disconnect event, I didn't have tracing enabled in the kernel but added some
dev_info()calls to determine what was going on. Added this todwc3_process_event_entry():
dev_info(dwc->dev, "event: 0x%x type=0x%x", event->raw, event->type.type);When disconnecting the cable from the host, I see this:
[ 50.841411] dwc3 3110000.usb: event:
0x6084type=0x42 [ 50.841457] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841494] dwc3 3110000.usb: event:0x6084type=0x42 [ 50.841534] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841571] dwc3 3110000.usb: event:0x4086type=0x43 [ 52.650990] dwc3 3110000.usb: event:0x30601type=0x0The "
0x4086" and "0x6084" messages are endpoint events that occur all the time while connected. The last event is the "suspend" one. After that, total silence.Quoted 8 lines
Quoted 3 lines
If you need traces, please point me to a description on how to obtain them.
Hi Mike,
I may be wrong, but can you help understand the mechanism as to how disconnect interrupt is generated in your targets. For example, on QC SoC's, this happens when
HS_PHY_CTRLregVBUS_VALIDbit is cleared and cable is disconnected. This is because the vbus line is not routed to controller. But from my calls with Synopsys previously, I remember that the vbus line is routed to the controller as well for other OEMs. In your SoC, what is the indication to controller that vbus is absent ?The board I'm testing this on is an LS1028ARDB. Looking at the schematic, VBUS is routed to the chip. There's also an LED attached to it, which turns off when I unplug the cable.
In the devicetree, I can't see any hint of NXP-specific "glue" in the DWC3 entries, so it uses the controller "as is":
compatible = "fsl,ls1028a-dwc3", "snps,dwc3"; reg = <
0x00x31000000x00x10000>; snps,dis_rxdet_inp3_quirk; snps,quirk-frame-length-adjustment = <0x20>; snps,incr-burst-type-adjustment = <1>, <4>,
<8>, <16>;
Quoted 6 lines
The "fsl,ls1028a-dwc3" keyword doesn't actually occur anywhere in the kernel, so it uses plain "snps,dwc3".
Quoted 1 line
Also, after this happens, do you see the next plug in working ?
Next plugin works, because of a "reset" event at that point that makes everything happy again.
Ahh, got it. Thanks for the info.
I ran into a similar issue before where disconnect isn't generated [1] and was suspecting it could be the case here but it isn't.
[1]: https://patchwork.kernel.org/project/linux-usb/patch/[email protected]/
Regards,
Krishna,
Quoted 3 lines
The state remains in "configured" while the cable is out. Plugging the cable back in makes it revert to "default" first, then it goes back into "configured".
Thinh Nguyen
maintainerHi,
Quoted 33 lines · Mike Looijmans
Quoted 10 lines · Thinh Nguyen
Hi,
Quoted 7 lines · Mike Looijmans
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends
DWC3_DEVICE_EVENT_SUSPENDin that case, and not aDWC3_DEVICE_EVENT_DISCONNECTas one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.Quoted 6 lines
Quoted 3 lines
Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
On disconnection, did you see disconnect interrupt? If so, it should transition to
USB_STATE_NOATTACHED. This change doesn't seem to directly address your issue. Can you provide the driver tracepoints?The device doesn't issue a disconnect event, I didn't have tracing enabled in the kernel but added some
dev_info()calls to determine what was going on. Added this todwc3_process_event_entry():
dev_info(dwc->dev, "event: 0x%x type=0x%x", event->raw, event->type.type);When disconnecting the cable from the host, I see this:
[ 50.841411] dwc3 3110000.usb: event:
0x6084type=0x42 [ 50.841457] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841494] dwc3 3110000.usb: event:0x6084type=0x42 [ 50.841534] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841571] dwc3 3110000.usb: event:0x4086type=0x43 [ 52.650990] dwc3 3110000.usb: event:0x30601type=0x0
Quoted 7 lines
The "
0x4086" and "0x6084" messages are endpoint events that occur all the time while connected. The last event is the "suspend" one. After that, total silence.If you need traces, please point me to a description on how to obtain them.
Let me know if you run into issues following this instructions to capture the tracepoints:
https://docs.kernel.org/driver-api/usb/dwc3.html#required-information
From the patch you provided, you only apply the change for the usb suspend. But did your device go through system suspend? If that's the case, then the dwc3 driver will cause a soft-disconnect. Currently that will not prompt a state change. We need the tracepoint to know more detail.
Until we have the tracepoints, you can experiment with this test patch. If my suspiction is correct, then this may resolve your issue:
drivers/usb/dwc3/gadget.c +2 -0
@@ -2682,6 +2682,8 @@ static int dwc3_gadget_soft_disconnect(struct dwc3 *dwc)*/ ret =dwc3_gadget_run_stop (dwc, false); +usb_gadget_set_state (dwc->gadget,USB_STATE_NOTATTACHED ); +/* * Stop the gadget after controller is halted, so that if needed, the * events to update EP0 state can still occur while the run/stop
--
Thanks,
Thinh
Quoted 39 lines · Thinh Nguyen
Hi,
Quoted 36 lines · Mike Looijmans
Quoted 10 lines · Thinh Nguyen
Hi,
Quoted 7 lines · Mike Looijmans
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends
DWC3_DEVICE_EVENT_SUSPENDin that case, and not aDWC3_DEVICE_EVENT_DISCONNECTas one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.Quoted 6 lines
Quoted 3 lines
Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
On disconnection, did you see disconnect interrupt? If so, it should transition to
USB_STATE_NOATTACHED. This change doesn't seem to directly address your issue. Can you provide the driver tracepoints?The device doesn't issue a disconnect event, I didn't have tracing enabled in the kernel but added some
dev_info()calls to determine what was going on. Added this todwc3_process_event_entry():
dev_info(dwc->dev, "event: 0x%x type=0x%x", event->raw, event->type.type);When disconnecting the cable from the host, I see this:
[ 50.841411] dwc3 3110000.usb: event:
0x6084type=0x42 [ 50.841457] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841494] dwc3 3110000.usb: event:0x6084type=0x42 [ 50.841534] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841571] dwc3 3110000.usb: event:0x4086type=0x43 [ 52.650990] dwc3 3110000.usb: event:0x30601type=0x0The "
0x4086" and "0x6084" messages are endpoint events that occur all the time while connected. The last event is the "suspend" one. After that, total silence.
Quoted 6 lines
Quoted 3 lines
If you need traces, please point me to a description on how to obtain them.
Let me know if you run into issues following this instructions to capture the tracepoints:
https://docs.kernel.org/driver-api/usb/dwc3.html#required-information
I've attached the traces as a tarball. Hope it survives.
At the start, the USB is up and running (and doing ethernet+mass storage). I saved the trace after pulling the USB cable.
Signature · 10 lines
Mike Looijmans System Expert TOPIC Embedded Products B.V. Materiaalweg 4, 5681 RJ Best The Netherlands T: +31 (0) 499 33 69 69 E: [email protected] W: www.topic.nl
Thinh Nguyen
maintainerQuoted 40 lines · Mike Looijmans
Quoted 39 lines · Thinh Nguyen
Hi,
Quoted 36 lines · Mike Looijmans
Quoted 10 lines · Thinh Nguyen
Hi,
Quoted 7 lines · Mike Looijmans
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends
DWC3_DEVICE_EVENT_SUSPENDin that case, and not aDWC3_DEVICE_EVENT_DISCONNECTas one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.Quoted 6 lines
Quoted 3 lines
Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
On disconnection, did you see disconnect interrupt? If so, it should transition to
USB_STATE_NOATTACHED. This change doesn't seem to directly address your issue. Can you provide the driver tracepoints?The device doesn't issue a disconnect event, I didn't have tracing enabled in the kernel but added some
dev_info()calls to determine what was going on. Added this todwc3_process_event_entry():
dev_info(dwc->dev, "event: 0x%x type=0x%x", event->raw, event->type.type);When disconnecting the cable from the host, I see this:
[ 50.841411] dwc3 3110000.usb: event:
0x6084type=0x42 [ 50.841457] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841494] dwc3 3110000.usb: event:0x6084type=0x42 [ 50.841534] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841571] dwc3 3110000.usb: event:0x4086type=0x43 [ 52.650990] dwc3 3110000.usb: event:0x30601type=0x0The "
0x4086" and "0x6084" messages are endpoint events that occur all the time while connected. The last event is the "suspend" one. After that, total silence.
Quoted 7 lines
Quoted 6 lines
Quoted 3 lines
If you need traces, please point me to a description on how to obtain them.
Let me know if you run into issues following this instructions to capture the tracepoints:
https://urldefense.com/v3/__https://docs.kernel.org/driver-api/usb/dwc3.html*required-information__;Iw!!A4F2R9G_pg!bahfjil5HEUq-fOHAwDfusutLJCLognfyLHTFLiSlVuZotpr99XBGg7nB0zRRnNF_M1pqEKcVa4KxNJwh3_F2dZWwVKTkUY$I've attached the traces as a tarball. Hope it survives.
Got them. Thanks.
Quoted 4 lines
At the start, the USB is up and running (and doing ethernet+mass storage). I saved the trace after pulling the USB cable.
From the capture, we can see that there's no system suspend, so there's no soft-disconnect.
Base on the suspend event, you're running in usb2 speed (ignore the incorrect U3 state, should be L2):
irq/94-dwc3-631 [000] D..1. 149.139290: dwc3_event: event (00030601): Suspend [U3]
The DSTS from the regdump indicated that you're still in L2 despite disconnected. Looks like the phy was unable to detect and wakeup from the disconnection to notify the controller.
Can you experiment with setting "snps,dis_u2_susphy_quirk" to disable usb2 phy suspend.
Does your device support SuperSpeed? If so, do you observe the same behavior while operating in SuperSpeed?
Thanks,
Thinh
Quoted 62 lines · Thinh Nguyen
Quoted 40 lines · Mike Looijmans
Quoted 39 lines · Thinh Nguyen
Hi,
Quoted 36 lines · Mike Looijmans
Quoted 10 lines · Thinh Nguyen
Hi,
Quoted 7 lines · Mike Looijmans
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends
DWC3_DEVICE_EVENT_SUSPENDin that case, and not aDWC3_DEVICE_EVENT_DISCONNECTas one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.Quoted 6 lines
Quoted 3 lines
Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
On disconnection, did you see disconnect interrupt? If so, it should transition to
USB_STATE_NOATTACHED. This change doesn't seem to directly address your issue. Can you provide the driver tracepoints?The device doesn't issue a disconnect event, I didn't have tracing enabled in the kernel but added some
dev_info()calls to determine what was going on. Added this todwc3_process_event_entry():
dev_info(dwc->dev, "event: 0x%x type=0x%x", event->raw, event->type.type);When disconnecting the cable from the host, I see this:
[ 50.841411] dwc3 3110000.usb: event:
0x6084type=0x42 [ 50.841457] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841494] dwc3 3110000.usb: event:0x6084type=0x42 [ 50.841534] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841571] dwc3 3110000.usb: event:0x4086type=0x43 [ 52.650990] dwc3 3110000.usb: event:0x30601type=0x0The "
0x4086" and "0x6084" messages are endpoint events that occur all the time while connected. The last event is the "suspend" one. After that, total silence.Quoted 7 lines
Quoted 6 lines
Quoted 3 lines
If you need traces, please point me to a description on how to obtain them.
Let me know if you run into issues following this instructions to capture the tracepoints:
https://urldefense.com/v3/__https://docs.kernel.org/driver-api/usb/dwc3.html*required-information__;Iw!!A4F2R9G_pg!bahfjil5HEUq-fOHAwDfusutLJCLognfyLHTFLiSlVuZotpr99XBGg7nB0zRRnNF_M1pqEKcVa4KxNJwh3_F2dZWwVKTkUY$I've attached the traces as a tarball. Hope it survives.
Got them. Thanks.
Quoted 4 lines
At the start, the USB is up and running (and doing ethernet+mass storage). I saved the trace after pulling the USB cable.
From the capture, we can see that there's no system suspend, so there's
no soft-disconnect.Base on the suspend event, you're running in usb2 speed (ignore the incorrect U3 state, should be L2):
Quoted 8 lines
irq/94-dwc3-631 [000] D..1. 149.139290: dwc3_event: event (00030601): Suspend [U3]The DSTS from the regdump indicated that you're still in L2 despite disconnected. Looks like the phy was unable to detect and wakeup from the disconnection to notify the controller.
Can you experiment with setting "snps,dis_u2_susphy_quirk" to disable usb2 phy suspend.
Will do.
Quoted 3 lines
Does your device support SuperSpeed? If so, do you observe the same behavior while operating in SuperSpeed?
It does, and it does.
The setup is SuperSpeed capable, and usually connects at this speed, but I didn't explicitly check if it set up a SS link for this particular trace. The behavior is always the same, regardless of whether it's in super or just high speed.
Signature · 1 line
Mike Looijmans
Quoted 59 lines · Thinh Nguyen
Quoted 40 lines · Mike Looijmans
Quoted 39 lines · Thinh Nguyen
Hi,
Quoted 36 lines · Mike Looijmans
Quoted 10 lines · Thinh Nguyen
Hi,
Quoted 7 lines · Mike Looijmans
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends
DWC3_DEVICE_EVENT_SUSPENDin that case, and not aDWC3_DEVICE_EVENT_DISCONNECTas one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.Quoted 6 lines
Quoted 3 lines
Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
On disconnection, did you see disconnect interrupt? If so, it should transition to
USB_STATE_NOATTACHED. This change doesn't seem to directly address your issue. Can you provide the driver tracepoints?The device doesn't issue a disconnect event, I didn't have tracing enabled in the kernel but added some
dev_info()calls to determine what was going on. Added this todwc3_process_event_entry():
dev_info(dwc->dev, "event: 0x%x type=0x%x", event->raw, event->type.type);When disconnecting the cable from the host, I see this:
[ 50.841411] dwc3 3110000.usb: event:
0x6084type=0x42 [ 50.841457] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841494] dwc3 3110000.usb: event:0x6084type=0x42 [ 50.841534] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841571] dwc3 3110000.usb: event:0x4086type=0x43 [ 52.650990] dwc3 3110000.usb: event:0x30601type=0x0The "
0x4086" and "0x6084" messages are endpoint events that occur all the time while connected. The last event is the "suspend" one. After that, total silence.Quoted 7 lines
Quoted 6 lines
Quoted 3 lines
If you need traces, please point me to a description on how to obtain them.
Let me know if you run into issues following this instructions to capture the tracepoints:
https://urldefense.com/v3/__https://docs.kernel.org/driver-api/usb/dwc3.html*required-information__;Iw!!A4F2R9G_pg!bahfjil5HEUq-fOHAwDfusutLJCLognfyLHTFLiSlVuZotpr99XBGg7nB0zRRnNF_M1pqEKcVa4KxNJwh3_F2dZWwVKTkUY$I've attached the traces as a tarball. Hope it survives.
Got them. Thanks.
Quoted 3 lines
At the start, the USB is up and running (and doing ethernet+mass storage). I saved the trace after pulling the USB cable.
From the capture, we can see that there's no system suspend, so there's
no soft-disconnect.Base on the suspend event, you're running in usb2 speed (ignore the incorrect U3 state, should be L2):
Quoted 8 lines
irq/94-dwc3-631 [000] D..1. 149.139290: dwc3_event: event (00030601): Suspend [U3]The DSTS from the regdump indicated that you're still in L2 despite disconnected. Looks like the phy was unable to detect and wakeup from the disconnection to notify the controller.
Can you experiment with setting "snps,dis_u2_susphy_quirk" to disable usb2 phy suspend.
Adding snps,dis_u2_susphy_quirk doesn't make a difference, behavior is identical.
Quoted 3 lines
Does your device support SuperSpeed? If so, do you observe the same behavior while operating in SuperSpeed?
Just checked, still connects with superspeed. What led you to think it was only high speed?
Do you want me to send new traces?
Signature · 10 lines
Mike Looijmans System Expert TOPIC Embedded Products B.V. Materiaalweg 4, 5681 RJ Best The Netherlands T: +31 (0) 499 33 69 69 E: [email protected] W: www.topic.nl
Thinh Nguyen
maintainerQuoted 74 lines · Mike Looijmans
Quoted 59 lines · Thinh Nguyen
Quoted 40 lines · Mike Looijmans
Quoted 39 lines · Thinh Nguyen
Hi,
Quoted 36 lines · Mike Looijmans
Quoted 10 lines · Thinh Nguyen
Hi,
Quoted 7 lines · Mike Looijmans
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends
DWC3_DEVICE_EVENT_SUSPENDin that case, and not aDWC3_DEVICE_EVENT_DISCONNECTas one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.Quoted 6 lines
Quoted 3 lines
Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
On disconnection, did you see disconnect interrupt? If so, it should transition to
USB_STATE_NOATTACHED. This change doesn't seem to directly address your issue. Can you provide the driver tracepoints?The device doesn't issue a disconnect event, I didn't have tracing enabled in the kernel but added some
dev_info()calls to determine what was going on. Added this todwc3_process_event_entry():
dev_info(dwc->dev, "event: 0x%x type=0x%x", event->raw, event->type.type);When disconnecting the cable from the host, I see this:
[ 50.841411] dwc3 3110000.usb: event:
0x6084type=0x42 [ 50.841457] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841494] dwc3 3110000.usb: event:0x6084type=0x42 [ 50.841534] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841571] dwc3 3110000.usb: event:0x4086type=0x43 [ 52.650990] dwc3 3110000.usb: event:0x30601type=0x0The "
0x4086" and "0x6084" messages are endpoint events that occur all the time while connected. The last event is the "suspend" one. After that, total silence.Quoted 7 lines
Quoted 6 lines
Quoted 3 lines
If you need traces, please point me to a description on how to obtain them.
Let me know if you run into issues following this instructions to capture the tracepoints:
https://urldefense.com/v3/__https://docs.kernel.org/driver-api/usb/dwc3.html*required-information__;Iw!!A4F2R9G_pg!bahfjil5HEUq-fOHAwDfusutLJCLognfyLHTFLiSlVuZotpr99XBGg7nB0zRRnNF_M1pqEKcVa4KxNJwh3_F2dZWwVKTkUY$I've attached the traces as a tarball. Hope it survives.
Got them. Thanks.
Quoted 3 lines
At the start, the USB is up and running (and doing ethernet+mass storage). I saved the trace after pulling the USB cable.
From the capture, we can see that there's no system suspend, so there's
no soft-disconnect.Base on the suspend event, you're running in usb2 speed (ignore the incorrect U3 state, should be L2):
Quoted 8 lines
irq/94-dwc3-631 [000] D..1. 149.139290: dwc3_event: event (00030601): Suspend [U3]The DSTS from the regdump indicated that you're still in L2 despite disconnected. Looks like the phy was unable to detect and wakeup from the disconnection to notify the controller.
Can you experiment with setting "snps,dis_u2_susphy_quirk" to disable usb2 phy suspend.
Adding snps,dis_u2_susphy_quirk doesn't make a difference, behavior is identical.
Quoted 1 line
Quoted 6 lines
Quoted 2 lines
Does your device support SuperSpeed? If so, do you observe the same behavior while operating in SuperSpeed?
Just checked, still connects with superspeed. What led you to think it was only high speed?
Bit(4) of event info (0003) from device event value (00030601) indicates usb2 speed.
Register DSTS field 2:0 indicates fullspeed. Even though this was captured after disconnection, the linkstate did not change, which led me to think that the connected speed did not change to Es.Disable either.
Quoted 2 lines
Do you want me to send new traces?
Can you also try to disable usb3 phy suspend with "snps,dis_u3_susphy_quirk" if you think it's connected in SuperSpeed?
Please capture the traces again if it's operating in SuperSpeed.
Thanks,
Thinh
Quoted 81 lines · Thinh Nguyen
Quoted 68 lines · Mike Looijmans
Quoted 59 lines · Thinh Nguyen
Quoted 40 lines · Mike Looijmans
Quoted 39 lines · Thinh Nguyen
Hi,
Quoted 36 lines · Mike Looijmans
Quoted 10 lines · Thinh Nguyen
Hi,
Quoted 7 lines · Mike Looijmans
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends
DWC3_DEVICE_EVENT_SUSPENDin that case, and not aDWC3_DEVICE_EVENT_DISCONNECTas one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.Quoted 6 lines
Quoted 3 lines
Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
On disconnection, did you see disconnect interrupt? If so, it should transition to
USB_STATE_NOATTACHED. This change doesn't seem to directly address your issue. Can you provide the driver tracepoints?The device doesn't issue a disconnect event, I didn't have tracing enabled in the kernel but added some
dev_info()calls to determine what was going on. Added this todwc3_process_event_entry():
dev_info(dwc->dev, "event: 0x%x type=0x%x", event->raw, event->type.type);When disconnecting the cable from the host, I see this:
[ 50.841411] dwc3 3110000.usb: event:
0x6084type=0x42 [ 50.841457] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841494] dwc3 3110000.usb: event:0x6084type=0x42 [ 50.841534] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841571] dwc3 3110000.usb: event:0x4086type=0x43 [ 52.650990] dwc3 3110000.usb: event:0x30601type=0x0The "
0x4086" and "0x6084" messages are endpoint events that occur all the time while connected. The last event is the "suspend" one. After that, total silence.Quoted 7 lines
Quoted 6 lines
Quoted 3 lines
If you need traces, please point me to a description on how to obtain them.
Let me know if you run into issues following this instructions to capture the tracepoints:
https://urldefense.com/v3/__https://docs.kernel.org/driver-api/usb/dwc3.html*required-information__;Iw!!A4F2R9G_pg!bahfjil5HEUq-fOHAwDfusutLJCLognfyLHTFLiSlVuZotpr99XBGg7nB0zRRnNF_M1pqEKcVa4KxNJwh3_F2dZWwVKTkUY$I've attached the traces as a tarball. Hope it survives.
Got them. Thanks.
Quoted 3 lines
At the start, the USB is up and running (and doing ethernet+mass storage). I saved the trace after pulling the USB cable.
From the capture, we can see that there's no system suspend, so there's
no soft-disconnect.Base on the suspend event, you're running in usb2 speed (ignore the incorrect U3 state, should be L2):
Quoted 8 lines
irq/94-dwc3-631 [000] D..1. 149.139290: dwc3_event: event (00030601): Suspend [U3]The DSTS from the regdump indicated that you're still in L2 despite disconnected. Looks like the phy was unable to detect and wakeup from the disconnection to notify the controller.
Can you experiment with setting "snps,dis_u2_susphy_quirk" to disable usb2 phy suspend.
Quoted 9 lines
Adding snps,dis_u2_susphy_quirk doesn't make a difference, behavior is identical.
Quoted 2 lines
Does your device support SuperSpeed? If so, do you observe the same behavior while operating in SuperSpeed?
Just checked, still connects with superspeed. What led you to think it was only high speed?
Bit(4) of event info (0003) from device event value (00030601) indicates usb2 speed.
Quoted 8 lines
Register DSTS field 2:0 indicates fullspeed. Even though this was captured after disconnection, the linkstate did not change, which led me to think that the connected speed did not change to Es.Disable either.
Quoted 2 lines
Do you want me to send new traces?
Can you also try to disable usb3 phy suspend with "snps,dis_u3_susphy_quirk" if you think it's connected in SuperSpeed?
Added this to the devicetree, but also no change in behavior.
Quoted 1 line
Please capture the traces again if it's operating in SuperSpeed.
I've attached new traces. Connected at superspeed (host reports "superspeed" in its dmesg log, and the real data transfer speed is way above highspeed)
I added register dumps before and after the disconnect.
Signature · 1 line
Mike Looijmans
Thinh Nguyen
maintainerQuoted 94 lines · Mike Looijmans
Quoted 81 lines · Thinh Nguyen
Quoted 68 lines · Mike Looijmans
Quoted 59 lines · Thinh Nguyen
Quoted 40 lines · Mike Looijmans
Quoted 39 lines · Thinh Nguyen
Hi,
Quoted 36 lines · Mike Looijmans
Quoted 10 lines · Thinh Nguyen
Hi,
Quoted 7 lines · Mike Looijmans
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends
DWC3_DEVICE_EVENT_SUSPENDin that case, and not aDWC3_DEVICE_EVENT_DISCONNECTas one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.Quoted 6 lines
Quoted 3 lines
Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
On disconnection, did you see disconnect interrupt? If so, it should transition to
USB_STATE_NOATTACHED. This change doesn't seem to directly address your issue. Can you provide the driver tracepoints?The device doesn't issue a disconnect event, I didn't have tracing enabled in the kernel but added some
dev_info()calls to determine what was going on. Added this todwc3_process_event_entry():
dev_info(dwc->dev, "event: 0x%x type=0x%x", event->raw, event->type.type);When disconnecting the cable from the host, I see this:
[ 50.841411] dwc3 3110000.usb: event:
0x6084type=0x42 [ 50.841457] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841494] dwc3 3110000.usb: event:0x6084type=0x42 [ 50.841534] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841571] dwc3 3110000.usb: event:0x4086type=0x43 [ 52.650990] dwc3 3110000.usb: event:0x30601type=0x0The "
0x4086" and "0x6084" messages are endpoint events that occur all the time while connected. The last event is the "suspend" one. After that, total silence.Quoted 7 lines
Quoted 6 lines
Quoted 3 lines
If you need traces, please point me to a description on how to obtain them.
Let me know if you run into issues following this instructions to capture the tracepoints:
https://urldefense.com/v3/__https://docs.kernel.org/driver-api/usb/dwc3.html*required-information__;Iw!!A4F2R9G_pg!bahfjil5HEUq-fOHAwDfusutLJCLognfyLHTFLiSlVuZotpr99XBGg7nB0zRRnNF_M1pqEKcVa4KxNJwh3_F2dZWwVKTkUY$I've attached the traces as a tarball. Hope it survives.
Got them. Thanks.
Quoted 3 lines
At the start, the USB is up and running (and doing ethernet+mass storage). I saved the trace after pulling the USB cable.
From the capture, we can see that there's no system suspend, so there's
no soft-disconnect.Base on the suspend event, you're running in usb2 speed (ignore the incorrect U3 state, should be L2):
Quoted 8 lines
irq/94-dwc3-631 [000] D..1. 149.139290: dwc3_event: event (00030601): Suspend [U3]The DSTS from the regdump indicated that you're still in L2 despite disconnected. Looks like the phy was unable to detect and wakeup from the disconnection to notify the controller.
Can you experiment with setting "snps,dis_u2_susphy_quirk" to disable usb2 phy suspend.
Quoted 9 lines
Adding snps,dis_u2_susphy_quirk doesn't make a difference, behavior is identical.
Quoted 2 lines
Does your device support SuperSpeed? If so, do you observe the same behavior while operating in SuperSpeed?
Just checked, still connects with superspeed. What led you to think it was only high speed?
Bit(4) of event info (0003) from device event value (00030601) indicates usb2 speed.
Quoted 8 lines
Register DSTS field 2:0 indicates fullspeed. Even though this was captured after disconnection, the linkstate did not change, which led me to think that the connected speed did not change to Es.Disable either.
Quoted 2 lines
Do you want me to send new traces?
Can you also try to disable usb3 phy suspend with "snps,dis_u3_susphy_quirk" if you think it's connected in SuperSpeed?
Added this to the devicetree, but also no change in behavior.
Quoted 7 lines
Quoted 1 line
Please capture the traces again if it's operating in SuperSpeed.
I've attached new traces. Connected at superspeed (host reports "superspeed" in its dmesg log, and the real data transfer speed is way above highspeed)
I added register dumps before and after the disconnect.
Thanks for the trace. It's indeed operating in SuperSpeed in the connected regdump. However, the GUSB3PIPECTL.SUSPENDENABLE is still set. Can you double check if you properly set the "snps,dis_u3_susphy_quirk"?
Thanks,
Thinh
Quoted 95 lines · Thinh Nguyen
Quoted 94 lines · Mike Looijmans
Quoted 81 lines · Thinh Nguyen
Quoted 68 lines · Mike Looijmans
Quoted 59 lines · Thinh Nguyen
Quoted 40 lines · Mike Looijmans
Quoted 39 lines · Thinh Nguyen
Hi,
Quoted 36 lines · Mike Looijmans
Quoted 10 lines · Thinh Nguyen
Hi,
Quoted 7 lines · Mike Looijmans
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends
DWC3_DEVICE_EVENT_SUSPENDin that case, and not aDWC3_DEVICE_EVENT_DISCONNECTas one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.Quoted 6 lines
Quoted 3 lines
Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
On disconnection, did you see disconnect interrupt? If so, it should transition to
USB_STATE_NOATTACHED. This change doesn't seem to directly address your issue. Can you provide the driver tracepoints?The device doesn't issue a disconnect event, I didn't have tracing enabled in the kernel but added some
dev_info()calls to determine what was going on. Added this todwc3_process_event_entry():
dev_info(dwc->dev, "event: 0x%x type=0x%x", event->raw, event->type.type);When disconnecting the cable from the host, I see this:
[ 50.841411] dwc3 3110000.usb: event:
0x6084type=0x42 [ 50.841457] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841494] dwc3 3110000.usb: event:0x6084type=0x42 [ 50.841534] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841571] dwc3 3110000.usb: event:0x4086type=0x43 [ 52.650990] dwc3 3110000.usb: event:0x30601type=0x0The "
0x4086" and "0x6084" messages are endpoint events that occur all the time while connected. The last event is the "suspend" one. After that, total silence.Quoted 7 lines
Quoted 6 lines
Quoted 3 lines
If you need traces, please point me to a description on how to obtain them.
Let me know if you run into issues following this instructions to capture the tracepoints:
https://urldefense.com/v3/__https://docs.kernel.org/driver-api/usb/dwc3.html*required-information__;Iw!!A4F2R9G_pg!bahfjil5HEUq-fOHAwDfusutLJCLognfyLHTFLiSlVuZotpr99XBGg7nB0zRRnNF_M1pqEKcVa4KxNJwh3_F2dZWwVKTkUY$I've attached the traces as a tarball. Hope it survives.
Got them. Thanks.
Quoted 3 lines
At the start, the USB is up and running (and doing ethernet+mass storage). I saved the trace after pulling the USB cable.
From the capture, we can see that there's no system suspend, so there's
no soft-disconnect.Base on the suspend event, you're running in usb2 speed (ignore the incorrect U3 state, should be L2):
Quoted 8 lines
irq/94-dwc3-631 [000] D..1. 149.139290: dwc3_event: event (00030601): Suspend [U3]The DSTS from the regdump indicated that you're still in L2 despite disconnected. Looks like the phy was unable to detect and wakeup from the disconnection to notify the controller.
Can you experiment with setting "snps,dis_u2_susphy_quirk" to disable usb2 phy suspend.
Quoted 9 lines
Adding snps,dis_u2_susphy_quirk doesn't make a difference, behavior is identical.
Quoted 2 lines
Does your device support SuperSpeed? If so, do you observe the same behavior while operating in SuperSpeed?
Just checked, still connects with superspeed. What led you to think it was only high speed?
Bit(4) of event info (0003) from device event value (00030601) indicates usb2 speed.
Quoted 8 lines
Register DSTS field 2:0 indicates fullspeed. Even though this was captured after disconnection, the linkstate did not change, which led me to think that the connected speed did not change to Es.Disable either.
Quoted 2 lines
Do you want me to send new traces?
Can you also try to disable usb3 phy suspend with "snps,dis_u3_susphy_quirk" if you think it's connected in SuperSpeed?
Added this to the devicetree, but also no change in behavior.
Quoted 1 line
Please capture the traces again if it's operating in SuperSpeed.
Quoted 8 lines
Quoted 5 lines
I've attached new traces. Connected at superspeed (host reports "superspeed" in its dmesg log, and the real data transfer speed is way above highspeed)
I added register dumps before and after the disconnect.
Thanks for the trace. It's indeed operating in SuperSpeed in the connected regdump. However, the GUSB3PIPECTL.SUSPENDENABLE is still set. Can you double check if you properly set the "snps,dis_u3_susphy_quirk"?
The trace was made before I added the property. It doesn't change the behavior. Should I create a new trace?
Signature · 10 lines
Mike Looijmans System Expert TOPIC Embedded Products B.V. Materiaalweg 4, 5681 RJ Best The Netherlands T: +31 (0) 499 33 69 69 E: [email protected] W: www.topic.nl
Quoted 95 lines · Thinh Nguyen
Quoted 94 lines · Mike Looijmans
Quoted 81 lines · Thinh Nguyen
Quoted 68 lines · Mike Looijmans
Quoted 59 lines · Thinh Nguyen
Quoted 40 lines · Mike Looijmans
Quoted 39 lines · Thinh Nguyen
Hi,
Quoted 36 lines · Mike Looijmans
Quoted 10 lines · Thinh Nguyen
Hi,
Quoted 7 lines · Mike Looijmans
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends
DWC3_DEVICE_EVENT_SUSPENDin that case, and not aDWC3_DEVICE_EVENT_DISCONNECTas one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.Quoted 6 lines
Quoted 3 lines
Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
On disconnection, did you see disconnect interrupt? If so, it should transition to
USB_STATE_NOATTACHED. This change doesn't seem to directly address your issue. Can you provide the driver tracepoints?The device doesn't issue a disconnect event, I didn't have tracing enabled in the kernel but added some
dev_info()calls to determine what was going on. Added this todwc3_process_event_entry():
dev_info(dwc->dev, "event: 0x%x type=0x%x", event->raw, event->type.type);When disconnecting the cable from the host, I see this:
[ 50.841411] dwc3 3110000.usb: event:
0x6084type=0x42 [ 50.841457] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841494] dwc3 3110000.usb: event:0x6084type=0x42 [ 50.841534] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841571] dwc3 3110000.usb: event:0x4086type=0x43 [ 52.650990] dwc3 3110000.usb: event:0x30601type=0x0The "
0x4086" and "0x6084" messages are endpoint events that occur all the time while connected. The last event is the "suspend" one. After that, total silence.Quoted 7 lines
Quoted 6 lines
Quoted 3 lines
If you need traces, please point me to a description on how to obtain them.
Let me know if you run into issues following this instructions to capture the tracepoints:
https://urldefense.com/v3/__https://docs.kernel.org/driver-api/usb/dwc3.html*required-information__;Iw!!A4F2R9G_pg!bahfjil5HEUq-fOHAwDfusutLJCLognfyLHTFLiSlVuZotpr99XBGg7nB0zRRnNF_M1pqEKcVa4KxNJwh3_F2dZWwVKTkUY$I've attached the traces as a tarball. Hope it survives.
Got them. Thanks.
Quoted 3 lines
At the start, the USB is up and running (and doing ethernet+mass storage). I saved the trace after pulling the USB cable.
From the capture, we can see that there's no system suspend, so there's
no soft-disconnect.Base on the suspend event, you're running in usb2 speed (ignore the incorrect U3 state, should be L2):
Quoted 8 lines
irq/94-dwc3-631 [000] D..1. 149.139290: dwc3_event: event (00030601): Suspend [U3]The DSTS from the regdump indicated that you're still in L2 despite disconnected. Looks like the phy was unable to detect and wakeup from the disconnection to notify the controller.
Can you experiment with setting "snps,dis_u2_susphy_quirk" to disable usb2 phy suspend.
Quoted 9 lines
Adding snps,dis_u2_susphy_quirk doesn't make a difference, behavior is identical.
Quoted 2 lines
Does your device support SuperSpeed? If so, do you observe the same behavior while operating in SuperSpeed?
Just checked, still connects with superspeed. What led you to think it was only high speed?
Bit(4) of event info (0003) from device event value (00030601) indicates usb2 speed.
Quoted 8 lines
Register DSTS field 2:0 indicates fullspeed. Even though this was captured after disconnection, the linkstate did not change, which led me to think that the connected speed did not change to Es.Disable either.
Quoted 2 lines
Do you want me to send new traces?
Can you also try to disable usb3 phy suspend with "snps,dis_u3_susphy_quirk" if you think it's connected in SuperSpeed?
Added this to the devicetree, but also no change in behavior.
Quoted 1 line
Please capture the traces again if it's operating in SuperSpeed.
Quoted 9 lines
Quoted 5 lines
I've attached new traces. Connected at superspeed (host reports "superspeed" in its dmesg log, and the real data transfer speed is way above highspeed)
I added register dumps before and after the disconnect.
Thanks for the trace. It's indeed operating in SuperSpeed in the connected regdump. However, the GUSB3PIPECTL.SUSPENDENABLE is still set. Can you double check if you properly set the "snps,dis_u3_susphy_quirk"?
I've attached a trace with both "quirks" in the devicetree:
snps,dis_u2_susphy_quirk; snps,dis_u3_susphy_quirk;
Interestingly, it still goes into "suspended" mode when I remove the cable.
Signature · 10 lines
Mike Looijmans System Expert TOPIC Embedded Products B.V. Materiaalweg 4, 5681 RJ Best The Netherlands T: +31 (0) 499 33 69 69 E: [email protected] W: www.topic.nl
Thinh Nguyen
maintainerQuoted 105 lines · Mike Looijmans
Quoted 95 lines · Thinh Nguyen
Quoted 94 lines · Mike Looijmans
Quoted 81 lines · Thinh Nguyen
Quoted 68 lines · Mike Looijmans
Quoted 59 lines · Thinh Nguyen
Quoted 40 lines · Mike Looijmans
Quoted 39 lines · Thinh Nguyen
Hi,
Quoted 36 lines · Mike Looijmans
Quoted 10 lines · Thinh Nguyen
Hi,
Quoted 7 lines · Mike Looijmans
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends
DWC3_DEVICE_EVENT_SUSPENDin that case, and not aDWC3_DEVICE_EVENT_DISCONNECTas one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.Quoted 6 lines
Quoted 3 lines
Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
On disconnection, did you see disconnect interrupt? If so, it should transition to
USB_STATE_NOATTACHED. This change doesn't seem to directly address your issue. Can you provide the driver tracepoints?The device doesn't issue a disconnect event, I didn't have tracing enabled in the kernel but added some
dev_info()calls to determine what was going on. Added this todwc3_process_event_entry():
dev_info(dwc->dev, "event: 0x%x type=0x%x", event->raw, event->type.type);When disconnecting the cable from the host, I see this:
[ 50.841411] dwc3 3110000.usb: event:
0x6084type=0x42 [ 50.841457] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841494] dwc3 3110000.usb: event:0x6084type=0x42 [ 50.841534] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841571] dwc3 3110000.usb: event:0x4086type=0x43 [ 52.650990] dwc3 3110000.usb: event:0x30601type=0x0The "
0x4086" and "0x6084" messages are endpoint events that occur all the time while connected. The last event is the "suspend" one. After that, total silence.Quoted 7 lines
Quoted 6 lines
Quoted 3 lines
If you need traces, please point me to a description on how to obtain them.
Let me know if you run into issues following this instructions to capture the tracepoints:
https://urldefense.com/v3/__https://docs.kernel.org/driver-api/usb/dwc3.html*required-information__;Iw!!A4F2R9G_pg!bahfjil5HEUq-fOHAwDfusutLJCLognfyLHTFLiSlVuZotpr99XBGg7nB0zRRnNF_M1pqEKcVa4KxNJwh3_F2dZWwVKTkUY$I've attached the traces as a tarball. Hope it survives.
Got them. Thanks.
Quoted 3 lines
At the start, the USB is up and running (and doing ethernet+mass storage). I saved the trace after pulling the USB cable.
From the capture, we can see that there's no system suspend, so there's
no soft-disconnect.Base on the suspend event, you're running in usb2 speed (ignore the incorrect U3 state, should be L2):
Quoted 8 lines
irq/94-dwc3-631 [000] D..1. 149.139290: dwc3_event: event (00030601): Suspend [U3]The DSTS from the regdump indicated that you're still in L2 despite disconnected. Looks like the phy was unable to detect and wakeup from the disconnection to notify the controller.
Can you experiment with setting "snps,dis_u2_susphy_quirk" to disable usb2 phy suspend.
Quoted 9 lines
Adding snps,dis_u2_susphy_quirk doesn't make a difference, behavior is identical.
Quoted 2 lines
Does your device support SuperSpeed? If so, do you observe the same behavior while operating in SuperSpeed?
Just checked, still connects with superspeed. What led you to think it was only high speed?
Bit(4) of event info (0003) from device event value (00030601) indicates usb2 speed.
Quoted 8 lines
Register DSTS field 2:0 indicates fullspeed. Even though this was captured after disconnection, the linkstate did not change, which led me to think that the connected speed did not change to Es.Disable either.
Quoted 2 lines
Do you want me to send new traces?
Can you also try to disable usb3 phy suspend with "snps,dis_u3_susphy_quirk" if you think it's connected in SuperSpeed?
Added this to the devicetree, but also no change in behavior.
Quoted 1 line
Please capture the traces again if it's operating in SuperSpeed.
Quoted 9 lines
Quoted 5 lines
I've attached new traces. Connected at superspeed (host reports "superspeed" in its dmesg log, and the real data transfer speed is way above highspeed)
I added register dumps before and after the disconnect.
Thanks for the trace. It's indeed operating in SuperSpeed in the connected regdump. However, the GUSB3PIPECTL.SUSPENDENABLE is still set. Can you double check if you properly set the "snps,dis_u3_susphy_quirk"?
Quoted 6 lines
I've attached a trace with both "quirks" in the devicetree:
snps,dis_u2_susphy_quirk; snps,dis_u3_susphy_quirk;Interestingly, it still goes into "suspended" mode when I remove the cable.
Wait, I thought the host initiated the usb suspend. Did you trigger usb suspend by putting the host in suspend? Or does the suspend event only come when you perform a disconnect?
Can you confirm if the suspend event was there before you disconnect the device?
Thanks,
Thinh
Quoted 110 lines · Thinh Nguyen
Quoted 109 lines · Mike Looijmans
Quoted 95 lines · Thinh Nguyen
Quoted 94 lines · Mike Looijmans
Quoted 81 lines · Thinh Nguyen
Quoted 68 lines · Mike Looijmans
Quoted 59 lines · Thinh Nguyen
Quoted 40 lines · Mike Looijmans
Quoted 39 lines · Thinh Nguyen
Hi,
Quoted 36 lines · Mike Looijmans
Quoted 10 lines · Thinh Nguyen
Hi,
Quoted 7 lines · Mike Looijmans
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends
DWC3_DEVICE_EVENT_SUSPENDin that case, and not aDWC3_DEVICE_EVENT_DISCONNECTas one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.Quoted 6 lines
Quoted 3 lines
Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
On disconnection, did you see disconnect interrupt? If so, it should transition to
USB_STATE_NOATTACHED. This change doesn't seem to directly address your issue. Can you provide the driver tracepoints?The device doesn't issue a disconnect event, I didn't have tracing enabled in the kernel but added some
dev_info()calls to determine what was going on. Added this todwc3_process_event_entry():
dev_info(dwc->dev, "event: 0x%x type=0x%x", event->raw, event->type.type);When disconnecting the cable from the host, I see this:
[ 50.841411] dwc3 3110000.usb: event:
0x6084type=0x42 [ 50.841457] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841494] dwc3 3110000.usb: event:0x6084type=0x42 [ 50.841534] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841571] dwc3 3110000.usb: event:0x4086type=0x43 [ 52.650990] dwc3 3110000.usb: event:0x30601type=0x0The "
0x4086" and "0x6084" messages are endpoint events that occur all the time while connected. The last event is the "suspend" one. After that, total silence.Quoted 7 lines
Quoted 6 lines
Quoted 3 lines
If you need traces, please point me to a description on how to obtain them.
Let me know if you run into issues following this instructions to capture the tracepoints:
https://urldefense.com/v3/__https://docs.kernel.org/driver-api/usb/dwc3.html*required-information__;Iw!!A4F2R9G_pg!bahfjil5HEUq-fOHAwDfusutLJCLognfyLHTFLiSlVuZotpr99XBGg7nB0zRRnNF_M1pqEKcVa4KxNJwh3_F2dZWwVKTkUY$I've attached the traces as a tarball. Hope it survives.
Got them. Thanks.
Quoted 3 lines
At the start, the USB is up and running (and doing ethernet+mass storage). I saved the trace after pulling the USB cable.
From the capture, we can see that there's no system suspend, so there's
no soft-disconnect.Base on the suspend event, you're running in usb2 speed (ignore the incorrect U3 state, should be L2):
Quoted 8 lines
irq/94-dwc3-631 [000] D..1. 149.139290: dwc3_event: event (00030601): Suspend [U3]The DSTS from the regdump indicated that you're still in L2 despite disconnected. Looks like the phy was unable to detect and wakeup from the disconnection to notify the controller.
Can you experiment with setting "snps,dis_u2_susphy_quirk" to disable usb2 phy suspend.
Quoted 9 lines
Adding snps,dis_u2_susphy_quirk doesn't make a difference, behavior is identical.
Quoted 2 lines
Does your device support SuperSpeed? If so, do you observe the same behavior while operating in SuperSpeed?
Just checked, still connects with superspeed. What led you to think it was only high speed?
Bit(4) of event info (0003) from device event value (00030601) indicates usb2 speed.
Quoted 8 lines
Register DSTS field 2:0 indicates fullspeed. Even though this was captured after disconnection, the linkstate did not change, which led me to think that the connected speed did not change to Es.Disable either.
Quoted 2 lines
Do you want me to send new traces?
Can you also try to disable usb3 phy suspend with "snps,dis_u3_susphy_quirk" if you think it's connected in SuperSpeed?
Added this to the devicetree, but also no change in behavior.
Quoted 1 line
Please capture the traces again if it's operating in SuperSpeed.
Quoted 9 lines
Quoted 5 lines
I've attached new traces. Connected at superspeed (host reports "superspeed" in its dmesg log, and the real data transfer speed is way above highspeed)
I added register dumps before and after the disconnect.
Thanks for the trace. It's indeed operating in SuperSpeed in the connected regdump. However, the GUSB3PIPECTL.SUSPENDENABLE is still set. Can you double check if you properly set the "snps,dis_u3_susphy_quirk"?
I've attached a trace with both "quirks" in the devicetree:
snps,dis_u2_susphy_quirk; snps,dis_u3_susphy_quirk;
Quoted 6 lines
Quoted 2 lines
Interestingly, it still goes into "suspended" mode when I remove the cable.
Wait, I thought the host initiated the usb suspend. Did you trigger usb suspend by putting the host in suspend? Or does the suspend event only come when you perform a disconnect?
All I do is unplug the cable. The host (PC running Ubuntu 22) doesn't eject or suspend or anything like that.
Quoted 3 lines
Can you confirm if the suspend event was there before you disconnect the device?
Disconnecting the cable is what leads to the "suspend" event.
M.
Thinh Nguyen
maintainerQuoted 8 lines · Mike Looijmans
Quoted 4 lines
Wait, I thought the host initiated the usb suspend. Did you trigger usb suspend by putting the host in suspend? Or does the suspend event only come when you perform a disconnect?
All I do is unplug the cable. The host (PC running Ubuntu 22) doesn't eject or suspend or anything like that.
This is a very typical connect/disconnect flow. I'm surprised that it's not caught on your platform before. What's the compatible string for your platform?
Quoted 7 lines
Quoted 4 lines
Can you confirm if the suspend event was there before you disconnect the device?
Disconnecting the cable is what leads to the "suspend" event.
Can you try this:
It's a simple workaround, but may not catch the issue while operating in Fullspeed.
drivers/usb/dwc3/gadget.c +12 -0
@@ -4339,6 +4339,18 @@ static void dwc3_gadget_suspend_interrupt(struct dwc3 *dwc, {enum dwc3_link_state next = evtinfo &DWC3_LINK_STATE_MASK ; +if (next ==DWC3_LINK_STATE_U3 ) { +u8 speed; +u32 reg; + + reg =dwc3_readl (dwc->regs,DWC3_DSTS ); + speed = reg &DWC3_DSTS_CONNECTSPD ; +if (dwc->speed != speed) { +dwc3_gadget_disconnect_interrupt (dwc); +return ; + } + } +if (!dwc->suspended && next ==DWC3_LINK_STATE_U3 ) { dwc->suspended = true;dwc3_suspend_gadget (dwc);
Otherwise, there's no other SW workaround that I can think of.
BR,
Thinh
Thinh Nguyen
maintainerQuoted 32 lines · Thinh Nguyen
Quoted 8 lines · Mike Looijmans
Quoted 4 lines
Wait, I thought the host initiated the usb suspend. Did you trigger usb suspend by putting the host in suspend? Or does the suspend event only come when you perform a disconnect?
All I do is unplug the cable. The host (PC running Ubuntu 22) doesn't eject or suspend or anything like that.
This is a very typical connect/disconnect flow. I'm surprised that it's not caught on your platform before. What's the compatible string for your platform?
Quoted 7 lines
Quoted 4 lines
Can you confirm if the suspend event was there before you disconnect the device?
Disconnecting the cable is what leads to the "suspend" event.
Can you try this:
It's a simple workaround, but may not catch the issue while operating in Fullspeed.
drivers/usb/dwc3/gadget.c +0
-0
drivers/usb/dwc3/gadget.c static void dwc3_gadget_suspend_interrupt(struct dwc3 *dwc, · line 4348
Quoted 10 lines
drivers/usb/dwc3/gadget.c +7
-0@@ -4339,6 +4339,18 @@ static void dwc3_gadget_suspend_interrupt(struct dwc3 *dwc, {enum dwc3_link_state next = evtinfo &DWC3_LINK_STATE_MASK ; +if (next ==DWC3_LINK_STATE_U3 ) { +u8 speed; +u32 reg; + + reg =dwc3_readl (dwc->regs,DWC3_DSTS ); + speed = reg &DWC3_DSTS_CONNECTSPD ; +if (dwc->speed != speed) {
Minor tweak to this condition to this instead:
if (dwc->gadget->speed != USB_SPEED_UNKNOWN &&
dwc->speed != speed) {Quoted 10 lines
drivers/usb/dwc3/gadget.c +5
-0+dwc3_gadget_disconnect_interrupt (dwc); +return ; + } + } +if (!dwc->suspended && next ==DWC3_LINK_STATE_U3 ) { dwc->suspended = true;dwc3_suspend_gadget (dwc);
Quoted 2 lines
Otherwise, there's no other SW workaround that I can think of.
Thanks,
Thinh
Quoted 60 lines · Thinh Nguyen
Hi,
Quoted 32 lines · Mike Looijmans
Quoted 10 lines · Thinh Nguyen
Hi,
Quoted 7 lines · Mike Looijmans
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends
DWC3_DEVICE_EVENT_SUSPENDin that case, and not aDWC3_DEVICE_EVENT_DISCONNECTas one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.Quoted 6 lines
Quoted 3 lines
Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
On disconnection, did you see disconnect interrupt? If so, it should transition to
USB_STATE_NOATTACHED. This change doesn't seem to directly address your issue. Can you provide the driver tracepoints?The device doesn't issue a disconnect event, I didn't have tracing enabled in the kernel but added some
dev_info()calls to determine what was going on. Added this todwc3_process_event_entry():
dev_info(dwc->dev, "event: 0x%x type=0x%x", event->raw, event->type.type);When disconnecting the cable from the host, I see this:
[ 50.841411] dwc3 3110000.usb: event:
0x6084type=0x42 [ 50.841457] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841494] dwc3 3110000.usb: event:0x6084type=0x42 [ 50.841534] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841571] dwc3 3110000.usb: event:0x4086type=0x43 [ 52.650990] dwc3 3110000.usb: event:0x30601type=0x0Quoted 7 lines
The "
0x4086" and "0x6084" messages are endpoint events that occur all the time while connected. The last event is the "suspend" one. After that, total silence.If you need traces, please point me to a description on how to obtain them.
Let me know if you run into issues following this instructions to capture the tracepoints:
https://docs.kernel.org/driver-api/usb/dwc3.html#required-informationFrom the patch you provided, you only apply the change for the usb
suspend. But did your device go through system suspend? If that's the case, then the dwc3 driver will cause a soft-disconnect. Currently that will not prompt a state change. We need the tracepoint to know more detail.Until we have the tracepoints, you can experiment with this test patch. If my suspiction is correct, then this may resolve your issue:
drivers/usb/dwc3/gadget.c +0
-0
drivers/usb/dwc3/gadget.c static int dwc3_gadget_soft_disconnect(struct dwc3 *dwc) · line 2689
Quoted 8 lines
drivers/usb/dwc3/gadget.c +2
-0@@ -2682,6 +2682,8 @@ static int dwc3_gadget_soft_disconnect(struct dwc3 *dwc)*/ ret =dwc3_gadget_run_stop (dwc, false); +usb_gadget_set_state (dwc->gadget,USB_STATE_NOTATTACHED ); +/* * Stop the gadget after controller is halted, so that if needed, the * events to update EP0 state can still occur while the run/stop
I tried the patch above, but it doesn't work. Apparently dwc3_gadget_soft_disconnect() doesn't get called when I unplug the cable.
Signature · 10 lines
Mike Looijmans System Expert TOPIC Embedded Products B.V. Materiaalweg 4, 5681 RJ Best The Netherlands T: +31 (0) 499 33 69 69 E: [email protected] W: www.topic.nl
Thinh Nguyen
maintainerQuoted 56 lines · Mike Looijmans
Quoted 55 lines · Thinh Nguyen
Hi,
Quoted 32 lines · Mike Looijmans
Quoted 10 lines · Thinh Nguyen
Hi,
Quoted 7 lines · Mike Looijmans
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends
DWC3_DEVICE_EVENT_SUSPENDin that case, and not aDWC3_DEVICE_EVENT_DISCONNECTas one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.Quoted 6 lines
Quoted 3 lines
Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
On disconnection, did you see disconnect interrupt? If so, it should transition to
USB_STATE_NOATTACHED. This change doesn't seem to directly address your issue. Can you provide the driver tracepoints?The device doesn't issue a disconnect event, I didn't have tracing enabled in the kernel but added some
dev_info()calls to determine what was going on. Added this todwc3_process_event_entry():
dev_info(dwc->dev, "event: 0x%x type=0x%x", event->raw, event->type.type);When disconnecting the cable from the host, I see this:
[ 50.841411] dwc3 3110000.usb: event:
0x6084type=0x42 [ 50.841457] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841494] dwc3 3110000.usb: event:0x6084type=0x42 [ 50.841534] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841571] dwc3 3110000.usb: event:0x4086type=0x43 [ 52.650990] dwc3 3110000.usb: event:0x30601type=0x0Quoted 7 lines
The "
0x4086" and "0x6084" messages are endpoint events that occur all the time while connected. The last event is the "suspend" one. After that, total silence.If you need traces, please point me to a description on how to obtain them.
Let me know if you run into issues following this instructions to capture the tracepoints:
https://urldefense.com/v3/__https://docs.kernel.org/driver-api/usb/dwc3.html*required-information__;Iw!!A4F2R9G_pg!epxtPmXHiizMg5_5igEYiKU483OZb1zcYK1M3afqXxIfgsw_cU_kdz9Rlpf1w-30JF0v4UUkxBViJtx4Prv3ZWchjKNHkKE$From the patch you provided, you only apply the change for the usb
suspend. But did your device go through system suspend? If that's the case, then the dwc3 driver will cause a soft-disconnect. Currently that will not prompt a state change. We need the tracepoint to know more detail.Until we have the tracepoints, you can experiment with this test patch. If my suspiction is correct, then this may resolve your issue:
Quoted 16 lines
drivers/usb/dwc3/gadget.c static int dwc3_gadget_soft_disconnect(struct dwc3 *dwc) · line 2688
Quoted 12 lines
drivers/usb/dwc3/gadget.c +2
-0@@ -2682,6 +2682,8 @@ static int dwc3_gadget_soft_disconnect(struct dwc3 *dwc)*/ ret =dwc3_gadget_run_stop (dwc, false); +usb_gadget_set_state (dwc->gadget,USB_STATE_NOTATTACHED ); +/* * Stop the gadget after controller is halted, so that if needed, the * events to update EP0 state can still occur while the run/stop I tried the patch above, but it doesn't work. Apparently
dwc3_gadget_soft_disconnect()doesn't get called when I unplug the cable.
Thanks for testing. There's no system suspend, so that's expected.
BR,
Thinh
Hi.
Sorry to resurrect this old thread but as far as I can see,
this issue was dropped.
As we have the same issue, not receiving a disconnect when cable is disconnected, we altered the patch and this version works for us.
Any thought on the patch?
Regards
/Ravineet
Quoted 74 lines · Thinh Nguyen
Quoted 56 lines · Mike Looijmans
Quoted 55 lines · Thinh Nguyen
Hi,
Quoted 32 lines · Mike Looijmans
Quoted 10 lines · Thinh Nguyen
Hi,
Quoted 7 lines · Mike Looijmans
When disconnecting the USB cable on an LS1028 device, nothing happens in userspace, which keeps thinking everything is still up and running. Turns out that the DWC3 controller only sends
DWC3_DEVICE_EVENT_SUSPENDin that case, and not aDWC3_DEVICE_EVENT_DISCONNECTas one would expect. As a result, sysfs attribute "state" remains "configured" until something resets it.Quoted 6 lines
Quoted 3 lines
Forward the "suspended" state to sysfs, so that the "state" at least changes into "suspended" when one removes the cable, and hence also matches the gadget's state when really suspended.
On disconnection, did you see disconnect interrupt? If so, it should transition to
USB_STATE_NOATTACHED. This change doesn't seem to directly address your issue. Can you provide the driver tracepoints?The device doesn't issue a disconnect event, I didn't have tracing enabled in the kernel but added some
dev_info()calls to determine what was going on. Added this todwc3_process_event_entry():
dev_info(dwc->dev, "event: 0x%x type=0x%x", event->raw, event->type.type);When disconnecting the cable from the host, I see this:
[ 50.841411] dwc3 3110000.usb: event:
0x6084type=0x42 [ 50.841457] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841494] dwc3 3110000.usb: event:0x6084type=0x42 [ 50.841534] dwc3 3110000.usb: event:0x4086type=0x43 [ 50.841571] dwc3 3110000.usb: event:0x4086type=0x43 [ 52.650990] dwc3 3110000.usb: event:0x30601type=0x0Quoted 7 lines
The "
0x4086" and "0x6084" messages are endpoint events that occur all the time while connected. The last event is the "suspend" one. After that, total silence.If you need traces, please point me to a description on how to obtain them.
Let me know if you run into issues following this instructions to capture the tracepoints:
https://urldefense.com/v3/__https://docs.kernel.org/driver-api/usb/dwc3.html*required-information__;Iw!!A4F2R9G_pg!epxtPmXHiizMg5_5igEYiKU483OZb1zcYK1M3afqXxIfgsw_cU_kdz9Rlpf1w-30JF0v4UUkxBViJtx4Prv3ZWchjKNHkKE$From the patch you provided, you only apply the change for the usb
suspend. But did your device go through system suspend? If that's the case, then the dwc3 driver will cause a soft-disconnect. Currently that will not prompt a state change. We need the tracepoint to know more detail.Until we have the tracepoints, you can experiment with this test patch. If my suspiction is correct, then this may resolve your issue:
Quoted 16 lines
drivers/usb/dwc3/gadget.c static int dwc3_gadget_soft_disconnect(struct dwc3 *dwc) · line 2688
Quoted 12 lines
drivers/usb/dwc3/gadget.c +2
-0@@ -2682,6 +2682,8 @@ static int dwc3_gadget_soft_disconnect(struct dwc3 *dwc)*/ ret =dwc3_gadget_run_stop (dwc, false); +usb_gadget_set_state (dwc->gadget,USB_STATE_NOTATTACHED ); +/* * Stop the gadget after controller is halted, so that if needed, the * events to update EP0 state can still occur while the run/stop I tried the patch above, but it doesn't work. Apparently
dwc3_gadget_soft_disconnect()doesn't get called when I unplug the cable.
Quoted 4 lines
Thanks for testing. There's no system suspend, so that's expected.
BR,
Thinh
From a689256e5d6cacdea09299014746522ae928f7c5 Mon Sep 17 00:00:00 2001
From: Ravineet Singh <[email protected]>
Date: Mon, 2 Mar 2026 16:44:46 +0100
Subject: [PATCH] usb: dwc3: gadget: set device in disconnected state when
unplugged
When a USB cable is disconnected on an LS1028 device, the DWC3 controller only sends DWC3_DEVICE_EVENT_SUSPEND and not a DWC3_DEVICE_EVENT_DISCONNECT.
Set device in disconnected state by issuingDWC3_DEVICE_EVENT_DISCONNECT.
--- drivers/usb/dwc3/gadget.c | 19 ++++++++++++++++--- 1 file changed, 16 insertions(+), 3 deletions(-)
drivers/usb/dwc3/gadget.c +16 -3
@@ -4440,9 +4440,22 @@ static void dwc3_gadget_suspend_interrupt(struct dwc3 *dwc, {enum dwc3_link_state next = evtinfo &DWC3_LINK_STATE_MASK ; -if (!dwc->suspended && next ==DWC3_LINK_STATE_U3 ) { - dwc->suspended = true; -dwc3_suspend_gadget (dwc); +if (next ==DWC3_LINK_STATE_U3 ) { +u8 speed; +u32 reg; + + reg =dwc3_readl (dwc->regs,DWC3_DSTS ); + speed = reg &DWC3_DSTS_CONNECTSPD ; +if (dwc->gadget->speed !=USB_SPEED_UNKNOWN && + speed ==USB_SPEED_UNKNOWN ) { +dwc3_gadget_disconnect_interrupt (dwc); +return ; + } + +if (!dwc->suspended) { + dwc->suspended = true; +dwc3_suspend_gadget (dwc); + } } dwc->link_state = next;
Signature · 1 line
2.43.0
Thinh Nguyen
maintainerQuoted 7 lines · Ravineet Singh
Hi.
Sorry to resurrect this old thread but as far as I can see,
this issue was dropped.
As we have the same issue, not receiving a disconnect when cable is disconnected, we altered the patch and this version works for us.
Quoted 6 lines
Any thought on the patch?
Regards
/Ravineet
Please avoid sending patches as attachment so we can keep track of the context. You can send as RFC patch and reference back to this discussion.
Regarding the patch, no it's not right. You're comparing the usb_device_speed enum value to the DSTS register value.
Can you share the regdump after disconnection?
BR,
Thinh
Understood, my bad, will send a RFC patch in the future.
Regdumps (without the patch) are attached.
Regards
/Ravineet
Quoted 18 lines · Thinh Nguyen
Quoted 7 lines · Ravineet Singh
Hi.
Sorry to resurrect this old thread but as far as I can see,
this issue was dropped.
As we have the same issue, not receiving a disconnect when cable is disconnected, we altered the patch and this version works for us.Quoted 6 lines
Any thought on the patch?
Regards
/RavineetPlease avoid sending patches as attachment so we can keep track of the context. You can send as RFC patch and reference back to this discussion.
Quoted 7 lines
Regarding the patch, no it's not right. You're comparing the
usb_device_speedenum value to the DSTS register value.Can you share the regdump after disconnection?
BR,
Thinh
GSBUSCFG0 = 0x22220009
GSBUSCFG1 = 0x00000700
GTXTHRCFG = 0x00000000
GRXTHRCFG = 0x00000000
GCTL = 0x30c12004
GEVTEN = 0x00000000
GSTS = 0x7e800000
GUCTL1 = 0x0104018a
GSNPSID = 0x5533290a
GGPIO = 0x00000000
GUID = 0x0006066c
GUCTL = 0x02008010
GBUSERRADDR0 = 0x00000000
GBUSERRADDR1 = 0x00000000
GPRTBIMAP0 = 0x00000000
GPRTBIMAP1 = 0x00000000
GHWPARAMS0 = 0x4020400a
GHWPARAMS1 = 0x81e0c93b
GHWPARAMS2 = 0x0130290a
GHWPARAMS3 = 0x04108485
GHWPARAMS4 = 0x47822004
GHWPARAMS5 = 0x04204108
GHWPARAMS6 = 0x09049c20
GHWPARAMS7 = 0x0308044d
GDBGFIFOSPACE = 0x00420000
GDBGLTSSM = 0x41090658
GDBGBMU = 0x01300010GPRTBIMAP_HS0 = 0x00000000GPRTBIMAP_HS1 = 0x00000000GPRTBIMAP_FS0 = 0x00000000GPRTBIMAP_FS1 = 0x00000000
GUCTL2 = 0x00000000VER_NUMBER = 0x00000000VER_TYPE = 0x00000000
GUSB2PHYCFG(0) = 0x40102540
GUSB2PHYCFG(1) = 0x00000000
GUSB2PHYCFG(2) = 0x00000000
GUSB2PHYCFG(3) = 0x00000000
GUSB2PHYCFG(4) = 0x00000000
GUSB2PHYCFG(5) = 0x00000000
GUSB2PHYCFG(6) = 0x00000000
GUSB2PHYCFG(7) = 0x00000000
GUSB2PHYCFG(8) = 0x00000000
GUSB2PHYCFG(9) = 0x00000000
GUSB2PHYCFG(10) = 0x00000000
GUSB2PHYCFG(11) = 0x00000000
GUSB2PHYCFG(12) = 0x00000000
GUSB2PHYCFG(13) = 0x00000000
GUSB2PHYCFG(14) = 0x00000000
GUSB2PHYCFG(15) = 0x00000000
GUSB2I2CCTL(0) = 0x00000000
GUSB2I2CCTL(1) = 0x00000000
GUSB2I2CCTL(2) = 0x00000000
GUSB2I2CCTL(3) = 0x00000000
GUSB2I2CCTL(4) = 0x00000000
GUSB2I2CCTL(5) = 0x00000000
GUSB2I2CCTL(6) = 0x00000000
GUSB2I2CCTL(7) = 0x00000000
GUSB2I2CCTL(8) = 0x00000000
GUSB2I2CCTL(9) = 0x00000000
GUSB2I2CCTL(10) = 0x00000000
GUSB2I2CCTL(11) = 0x00000000
GUSB2I2CCTL(12) = 0x00000000
GUSB2I2CCTL(13) = 0x00000000
GUSB2I2CCTL(14) = 0x00000000
GUSB2I2CCTL(15) = 0x00000000
GUSB2PHYACC(0) = 0x00000000
GUSB2PHYACC(1) = 0x00000000
GUSB2PHYACC(2) = 0x00000000
GUSB2PHYACC(3) = 0x00000000
GUSB2PHYACC(4) = 0x00000000
GUSB2PHYACC(5) = 0x00000000
GUSB2PHYACC(6) = 0x00000000
GUSB2PHYACC(7) = 0x00000000
GUSB2PHYACC(8) = 0x00000000
GUSB2PHYACC(9) = 0x00000000
GUSB2PHYACC(10) = 0x00000000
GUSB2PHYACC(11) = 0x00000000
GUSB2PHYACC(12) = 0x00000000
GUSB2PHYACC(13) = 0x00000000
GUSB2PHYACC(14) = 0x00000000
GUSB2PHYACC(15) = 0x00000000
GUSB3PIPECTL(0) = 0x110e0002
GUSB3PIPECTL(1) = 0x00000000
GUSB3PIPECTL(2) = 0x00000000
GUSB3PIPECTL(3) = 0x00000000
GUSB3PIPECTL(4) = 0x00000000
GUSB3PIPECTL(5) = 0x00000000
GUSB3PIPECTL(6) = 0x00000000
GUSB3PIPECTL(7) = 0x00000000
GUSB3PIPECTL(8) = 0x00000000
GUSB3PIPECTL(9) = 0x00000000
GUSB3PIPECTL(10) = 0x00000000
GUSB3PIPECTL(11) = 0x00000000
GUSB3PIPECTL(12) = 0x00000000
GUSB3PIPECTL(13) = 0x00000000
GUSB3PIPECTL(14) = 0x00000000
GUSB3PIPECTL(15) = 0x00000000
GTXFIFOSIZ(0) = 0x00000042
GTXFIFOSIZ(1) = 0x00420184
GTXFIFOSIZ(2) = 0x01c60184
GTXFIFOSIZ(3) = 0x034a0103
GTXFIFOSIZ(4) = 0x00000000
GTXFIFOSIZ(5) = 0x00000000
GTXFIFOSIZ(6) = 0x00000000
GTXFIFOSIZ(7) = 0x00000000
GTXFIFOSIZ(8) = 0x00000000
GTXFIFOSIZ(9) = 0x00000000
GTXFIFOSIZ(10) = 0x00000000
GTXFIFOSIZ(11) = 0x00000000
GTXFIFOSIZ(12) = 0x00000000
GTXFIFOSIZ(13) = 0x00000000
GTXFIFOSIZ(14) = 0x00000000
GTXFIFOSIZ(15) = 0x00000000
GTXFIFOSIZ(16) = 0x00000000
GTXFIFOSIZ(17) = 0x00000000
GTXFIFOSIZ(18) = 0x00000000
GTXFIFOSIZ(19) = 0x00000000
GTXFIFOSIZ(20) = 0x00000000
GTXFIFOSIZ(21) = 0x00000000
GTXFIFOSIZ(22) = 0x00000000
GTXFIFOSIZ(23) = 0x00000000
GTXFIFOSIZ(24) = 0x00000000
GTXFIFOSIZ(25) = 0x00000000
GTXFIFOSIZ(26) = 0x00000000
GTXFIFOSIZ(27) = 0x00000000
GTXFIFOSIZ(28) = 0x00000000
GTXFIFOSIZ(29) = 0x00000000
GTXFIFOSIZ(30) = 0x00000000
GTXFIFOSIZ(31) = 0x00000000
GRXFIFOSIZ(0) = 0x00000305
GRXFIFOSIZ(1) = 0x03050000
GRXFIFOSIZ(2) = 0x03050000
GRXFIFOSIZ(3) = 0x00000000
GRXFIFOSIZ(4) = 0x00000000
GRXFIFOSIZ(5) = 0x00000000
GRXFIFOSIZ(6) = 0x00000000
GRXFIFOSIZ(7) = 0x00000000
GRXFIFOSIZ(8) = 0x00000000
GRXFIFOSIZ(9) = 0x00000000
GRXFIFOSIZ(10) = 0x00000000
GRXFIFOSIZ(11) = 0x00000000
GRXFIFOSIZ(12) = 0x00000000
GRXFIFOSIZ(13) = 0x00000000
GRXFIFOSIZ(14) = 0x00000000
GRXFIFOSIZ(15) = 0x00000000
GRXFIFOSIZ(16) = 0x00000000
GRXFIFOSIZ(17) = 0x00000000
GRXFIFOSIZ(18) = 0x00000000
GRXFIFOSIZ(19) = 0x00000000
GRXFIFOSIZ(20) = 0x00000000
GRXFIFOSIZ(21) = 0x00000000
GRXFIFOSIZ(22) = 0x00000000
GRXFIFOSIZ(23) = 0x00000000
GRXFIFOSIZ(24) = 0x00000000
GRXFIFOSIZ(25) = 0x00000000
GRXFIFOSIZ(26) = 0x00000000
GRXFIFOSIZ(27) = 0x00000000
GRXFIFOSIZ(28) = 0x00000000
GRXFIFOSIZ(29) = 0x00000000
GRXFIFOSIZ(30) = 0x00000000
GRXFIFOSIZ(31) = 0x00000000
GEVNTADRLO(0) = 0xfffff000
GEVNTADRHI(0) = 0x0000ffff
GEVNTSIZ(0) = 0x00001000
GEVNTCOUNT(0) = 0x00000000
GHWPARAMS8 = 0x00000904
GUCTL3 = 0x00000000
GFLADJ = 0x000000a0
DCFG = 0x00cc0814
DCTL = 0x8cf00a00
DEVTEN = 0x00000257
DSTS = 0x000eec88
DGCMDPAR = 0x00000000
DGCMD = 0x00000000
DALEPENA = 0x0000002f
DEPCMDPAR2(0) = 0x00000000
DEPCMDPAR1(0) = 0xffffe000
DEPCMDPAR0(0) = 0x0000ffff
DEPCMD(0) = 0x00000006
DEPCMDPAR2(1) = 0x00000000
DEPCMDPAR1(1) = 0xffffe000
DEPCMDPAR0(1) = 0x0000ffff
DEPCMD(1) = 0x00010006
DEPCMDPAR2(2) = 0x00000000
DEPCMDPAR1(2) = 0xffffc000
DEPCMDPAR0(2) = 0x0000ffff
DEPCMD(2) = 0x00040007
DEPCMDPAR2(3) = 0x00000000
DEPCMDPAR1(3) = 0xffffb000
DEPCMDPAR0(3) = 0x0000ffff
DEPCMD(3) = 0x00030007
DEPCMDPAR2(4) = 0x00000000
DEPCMDPAR1(4) = 0x00000000
DEPCMDPAR0(4) = 0x00000000
DEPCMD(4) = 0x00000000
DEPCMDPAR2(5) = 0x00000000
DEPCMDPAR1(5) = 0xffff9000
DEPCMDPAR0(5) = 0x0000ffff
DEPCMD(5) = 0x00020007
DEPCMDPAR2(6) = 0x00000000
DEPCMDPAR1(6) = 0x00000000
DEPCMDPAR0(6) = 0x00000000
DEPCMD(6) = 0x00000000
DEPCMDPAR2(7) = 0x00000000
DEPCMDPAR1(7) = 0x00000000
DEPCMDPAR0(7) = 0x00000000
DEPCMD(7) = 0x00000000
DEPCMDPAR2(8) = 0x00000000
DEPCMDPAR1(8) = 0x00000000
DEPCMDPAR0(8) = 0x00000000
DEPCMD(8) = 0x00000000
DEPCMDPAR2(9) = 0x00000000
DEPCMDPAR1(9) = 0x00000000
DEPCMDPAR0(9) = 0x00000000
DEPCMD(9) = 0x00000000
DEPCMDPAR2(10) = 0x00000000
DEPCMDPAR1(10) = 0x00000000
DEPCMDPAR0(10) = 0x00000000
DEPCMD(10) = 0x00000000
DEPCMDPAR2(11) = 0x00000000
DEPCMDPAR1(11) = 0x00000000
DEPCMDPAR0(11) = 0x00000000
DEPCMD(11) = 0x00000000
DEPCMDPAR2(12) = 0x00000000
DEPCMDPAR1(12) = 0x00000000
DEPCMDPAR0(12) = 0x00000000
DEPCMD(12) = 0x00000000
DEPCMDPAR2(13) = 0x00000000
DEPCMDPAR1(13) = 0x00000000
DEPCMDPAR0(13) = 0x00000000
DEPCMD(13) = 0x00000000
DEPCMDPAR2(14) = 0x00000000
DEPCMDPAR1(14) = 0x00000000
DEPCMDPAR0(14) = 0x00000000
DEPCMD(14) = 0x00000000
DEPCMDPAR2(15) = 0x00000000
DEPCMDPAR1(15) = 0x00000000
DEPCMDPAR0(15) = 0x00000000
DEPCMD(15) = 0x00000000
DEPCMDPAR2(16) = 0x00000000
DEPCMDPAR1(16) = 0x00000000
DEPCMDPAR0(16) = 0x00000000
DEPCMD(16) = 0x00000000
DEPCMDPAR2(17) = 0x00000000
DEPCMDPAR1(17) = 0x00000000
DEPCMDPAR0(17) = 0x00000000
DEPCMD(17) = 0x00000000
DEPCMDPAR2(18) = 0x00000000
DEPCMDPAR1(18) = 0x00000000
DEPCMDPAR0(18) = 0x00000000
DEPCMD(18) = 0x00000000
DEPCMDPAR2(19) = 0x00000000
DEPCMDPAR1(19) = 0x00000000
DEPCMDPAR0(19) = 0x00000000
DEPCMD(19) = 0x00000000
DEPCMDPAR2(20) = 0x00000000
DEPCMDPAR1(20) = 0x00000000
DEPCMDPAR0(20) = 0x00000000
DEPCMD(20) = 0x00000000
DEPCMDPAR2(21) = 0x00000000
DEPCMDPAR1(21) = 0x00000000
DEPCMDPAR0(21) = 0x00000000
DEPCMD(21) = 0x00000000
DEPCMDPAR2(22) = 0x00000000
DEPCMDPAR1(22) = 0x00000000
DEPCMDPAR0(22) = 0x00000000
DEPCMD(22) = 0x00000000
DEPCMDPAR2(23) = 0x00000000
DEPCMDPAR1(23) = 0x00000000
DEPCMDPAR0(23) = 0x00000000
DEPCMD(23) = 0x00000000
DEPCMDPAR2(24) = 0x00000000
DEPCMDPAR1(24) = 0x00000000
DEPCMDPAR0(24) = 0x00000000
DEPCMD(24) = 0x00000000
DEPCMDPAR2(25) = 0x00000000
DEPCMDPAR1(25) = 0x00000000
DEPCMDPAR0(25) = 0x00000000
DEPCMD(25) = 0x00000000
DEPCMDPAR2(26) = 0x00000000
DEPCMDPAR1(26) = 0x00000000
DEPCMDPAR0(26) = 0x00000000
DEPCMD(26) = 0x00000000
DEPCMDPAR2(27) = 0x00000000
DEPCMDPAR1(27) = 0x00000000
DEPCMDPAR0(27) = 0x00000000
DEPCMD(27) = 0x00000000
DEPCMDPAR2(28) = 0x00000000
DEPCMDPAR1(28) = 0x00000000
DEPCMDPAR0(28) = 0x00000000
DEPCMD(28) = 0x00000000
DEPCMDPAR2(29) = 0x00000000
DEPCMDPAR1(29) = 0x00000000
DEPCMDPAR0(29) = 0x00000000
DEPCMD(29) = 0x00000000
DEPCMDPAR2(30) = 0x00000000
DEPCMDPAR1(30) = 0x00000000
DEPCMDPAR0(30) = 0x00000000
DEPCMD(30) = 0x00000000
DEPCMDPAR2(31) = 0x00000000
DEPCMDPAR1(31) = 0x00000000
DEPCMDPAR0(31) = 0x00000000
DEPCMD(31) = 0x00000000
OCFG = 0x00000000
OCTL = 0x00000040
OEVT = 0x80000000
OEVTEN = 0x00000000
OSTS = 0x0000201f
GSBUSCFG0 = 0x22220009
GSBUSCFG1 = 0x00000700
GTXTHRCFG = 0x00000000
GRXTHRCFG = 0x00000000
GCTL = 0x30c12004
GEVTEN = 0x00000000
GSTS = 0x7e800000
GUCTL1 = 0x0104018a
GSNPSID = 0x5533290a
GGPIO = 0x00000000
GUID = 0x0006066c
GUCTL = 0x02008010
GBUSERRADDR0 = 0x00000000
GBUSERRADDR1 = 0x00000000
GPRTBIMAP0 = 0x00000000
GPRTBIMAP1 = 0x00000000
GHWPARAMS0 = 0x4020400a
GHWPARAMS1 = 0x81e0c93b
GHWPARAMS2 = 0x0130290a
GHWPARAMS3 = 0x04108485
GHWPARAMS4 = 0x47822004
GHWPARAMS5 = 0x04204108
GHWPARAMS6 = 0x09049c20
GHWPARAMS7 = 0x0308044d
GDBGFIFOSPACE = 0x00420000
GDBGLTSSM = 0x41090658
GDBGBMU = 0x01300010GPRTBIMAP_HS0 = 0x00000000GPRTBIMAP_HS1 = 0x00000000GPRTBIMAP_FS0 = 0x00000000GPRTBIMAP_FS1 = 0x00000000
GUCTL2 = 0x00000000VER_NUMBER = 0x00000000VER_TYPE = 0x00000000
GUSB2PHYCFG(0) = 0x40102540
GUSB2PHYCFG(1) = 0x00000000
GUSB2PHYCFG(2) = 0x00000000
GUSB2PHYCFG(3) = 0x00000000
GUSB2PHYCFG(4) = 0x00000000
GUSB2PHYCFG(5) = 0x00000000
GUSB2PHYCFG(6) = 0x00000000
GUSB2PHYCFG(7) = 0x00000000
GUSB2PHYCFG(8) = 0x00000000
GUSB2PHYCFG(9) = 0x00000000
GUSB2PHYCFG(10) = 0x00000000
GUSB2PHYCFG(11) = 0x00000000
GUSB2PHYCFG(12) = 0x00000000
GUSB2PHYCFG(13) = 0x00000000
GUSB2PHYCFG(14) = 0x00000000
GUSB2PHYCFG(15) = 0x00000000
GUSB2I2CCTL(0) = 0x00000000
GUSB2I2CCTL(1) = 0x00000000
GUSB2I2CCTL(2) = 0x00000000
GUSB2I2CCTL(3) = 0x00000000
GUSB2I2CCTL(4) = 0x00000000
GUSB2I2CCTL(5) = 0x00000000
GUSB2I2CCTL(6) = 0x00000000
GUSB2I2CCTL(7) = 0x00000000
GUSB2I2CCTL(8) = 0x00000000
GUSB2I2CCTL(9) = 0x00000000
GUSB2I2CCTL(10) = 0x00000000
GUSB2I2CCTL(11) = 0x00000000
GUSB2I2CCTL(12) = 0x00000000
GUSB2I2CCTL(13) = 0x00000000
GUSB2I2CCTL(14) = 0x00000000
GUSB2I2CCTL(15) = 0x00000000
GUSB2PHYACC(0) = 0x00000000
GUSB2PHYACC(1) = 0x00000000
GUSB2PHYACC(2) = 0x00000000
GUSB2PHYACC(3) = 0x00000000
GUSB2PHYACC(4) = 0x00000000
GUSB2PHYACC(5) = 0x00000000
GUSB2PHYACC(6) = 0x00000000
GUSB2PHYACC(7) = 0x00000000
GUSB2PHYACC(8) = 0x00000000
GUSB2PHYACC(9) = 0x00000000
GUSB2PHYACC(10) = 0x00000000
GUSB2PHYACC(11) = 0x00000000
GUSB2PHYACC(12) = 0x00000000
GUSB2PHYACC(13) = 0x00000000
GUSB2PHYACC(14) = 0x00000000
GUSB2PHYACC(15) = 0x00000000
GUSB3PIPECTL(0) = 0x110e0002
GUSB3PIPECTL(1) = 0x00000000
GUSB3PIPECTL(2) = 0x00000000
GUSB3PIPECTL(3) = 0x00000000
GUSB3PIPECTL(4) = 0x00000000
GUSB3PIPECTL(5) = 0x00000000
GUSB3PIPECTL(6) = 0x00000000
GUSB3PIPECTL(7) = 0x00000000
GUSB3PIPECTL(8) = 0x00000000
GUSB3PIPECTL(9) = 0x00000000
GUSB3PIPECTL(10) = 0x00000000
GUSB3PIPECTL(11) = 0x00000000
GUSB3PIPECTL(12) = 0x00000000
GUSB3PIPECTL(13) = 0x00000000
GUSB3PIPECTL(14) = 0x00000000
GUSB3PIPECTL(15) = 0x00000000
GTXFIFOSIZ(0) = 0x00000042
GTXFIFOSIZ(1) = 0x00420184
GTXFIFOSIZ(2) = 0x01c60184
GTXFIFOSIZ(3) = 0x034a0103
GTXFIFOSIZ(4) = 0x00000000
GTXFIFOSIZ(5) = 0x00000000
GTXFIFOSIZ(6) = 0x00000000
GTXFIFOSIZ(7) = 0x00000000
GTXFIFOSIZ(8) = 0x00000000
GTXFIFOSIZ(9) = 0x00000000
GTXFIFOSIZ(10) = 0x00000000
GTXFIFOSIZ(11) = 0x00000000
GTXFIFOSIZ(12) = 0x00000000
GTXFIFOSIZ(13) = 0x00000000
GTXFIFOSIZ(14) = 0x00000000
GTXFIFOSIZ(15) = 0x00000000
GTXFIFOSIZ(16) = 0x00000000
GTXFIFOSIZ(17) = 0x00000000
GTXFIFOSIZ(18) = 0x00000000
GTXFIFOSIZ(19) = 0x00000000
GTXFIFOSIZ(20) = 0x00000000
GTXFIFOSIZ(21) = 0x00000000
GTXFIFOSIZ(22) = 0x00000000
GTXFIFOSIZ(23) = 0x00000000
GTXFIFOSIZ(24) = 0x00000000
GTXFIFOSIZ(25) = 0x00000000
GTXFIFOSIZ(26) = 0x00000000
GTXFIFOSIZ(27) = 0x00000000
GTXFIFOSIZ(28) = 0x00000000
GTXFIFOSIZ(29) = 0x00000000
GTXFIFOSIZ(30) = 0x00000000
GTXFIFOSIZ(31) = 0x00000000
GRXFIFOSIZ(0) = 0x00000305
GRXFIFOSIZ(1) = 0x03050000
GRXFIFOSIZ(2) = 0x03050000
GRXFIFOSIZ(3) = 0x00000000
GRXFIFOSIZ(4) = 0x00000000
GRXFIFOSIZ(5) = 0x00000000
GRXFIFOSIZ(6) = 0x00000000
GRXFIFOSIZ(7) = 0x00000000
GRXFIFOSIZ(8) = 0x00000000
GRXFIFOSIZ(9) = 0x00000000
GRXFIFOSIZ(10) = 0x00000000
GRXFIFOSIZ(11) = 0x00000000
GRXFIFOSIZ(12) = 0x00000000
GRXFIFOSIZ(13) = 0x00000000
GRXFIFOSIZ(14) = 0x00000000
GRXFIFOSIZ(15) = 0x00000000
GRXFIFOSIZ(16) = 0x00000000
GRXFIFOSIZ(17) = 0x00000000
GRXFIFOSIZ(18) = 0x00000000
GRXFIFOSIZ(19) = 0x00000000
GRXFIFOSIZ(20) = 0x00000000
GRXFIFOSIZ(21) = 0x00000000
GRXFIFOSIZ(22) = 0x00000000
GRXFIFOSIZ(23) = 0x00000000
GRXFIFOSIZ(24) = 0x00000000
GRXFIFOSIZ(25) = 0x00000000
GRXFIFOSIZ(26) = 0x00000000
GRXFIFOSIZ(27) = 0x00000000
GRXFIFOSIZ(28) = 0x00000000
GRXFIFOSIZ(29) = 0x00000000
GRXFIFOSIZ(30) = 0x00000000
GRXFIFOSIZ(31) = 0x00000000
GEVNTADRLO(0) = 0xfffff000
GEVNTADRHI(0) = 0x0000ffff
GEVNTSIZ(0) = 0x00001000
GEVNTCOUNT(0) = 0x00000000
GHWPARAMS8 = 0x00000904
GUCTL3 = 0x00000000
GFLADJ = 0x000000a0
DCFG = 0x00cc0814
DCTL = 0x8cf00a00
DEVTEN = 0x00000257
DSTS = 0x0002cc40
DGCMDPAR = 0x00000000
DGCMD = 0x00000000
DALEPENA = 0x0000002f
DEPCMDPAR2(0) = 0x00000000
DEPCMDPAR1(0) = 0xffffe000
DEPCMDPAR0(0) = 0x0000ffff
DEPCMD(0) = 0x00000006
DEPCMDPAR2(1) = 0x00000000
DEPCMDPAR1(1) = 0xffffe000
DEPCMDPAR0(1) = 0x0000ffff
DEPCMD(1) = 0x00010006
DEPCMDPAR2(2) = 0x00000000
DEPCMDPAR1(2) = 0xffffc000
DEPCMDPAR0(2) = 0x0000ffff
DEPCMD(2) = 0x00040007
DEPCMDPAR2(3) = 0x00000000
DEPCMDPAR1(3) = 0xffffb000
DEPCMDPAR0(3) = 0x0000ffff
DEPCMD(3) = 0x00030007
DEPCMDPAR2(4) = 0x00000000
DEPCMDPAR1(4) = 0x00000000
DEPCMDPAR0(4) = 0x00000000
DEPCMD(4) = 0x00000000
DEPCMDPAR2(5) = 0x00000000
DEPCMDPAR1(5) = 0xffff9000
DEPCMDPAR0(5) = 0x0000ffff
DEPCMD(5) = 0x00020007
DEPCMDPAR2(6) = 0x00000000
DEPCMDPAR1(6) = 0x00000000
DEPCMDPAR0(6) = 0x00000000
DEPCMD(6) = 0x00000000
DEPCMDPAR2(7) = 0x00000000
DEPCMDPAR1(7) = 0x00000000
DEPCMDPAR0(7) = 0x00000000
DEPCMD(7) = 0x00000000
DEPCMDPAR2(8) = 0x00000000
DEPCMDPAR1(8) = 0x00000000
DEPCMDPAR0(8) = 0x00000000
DEPCMD(8) = 0x00000000
DEPCMDPAR2(9) = 0x00000000
DEPCMDPAR1(9) = 0x00000000
DEPCMDPAR0(9) = 0x00000000
DEPCMD(9) = 0x00000000
DEPCMDPAR2(10) = 0x00000000
DEPCMDPAR1(10) = 0x00000000
DEPCMDPAR0(10) = 0x00000000
DEPCMD(10) = 0x00000000
DEPCMDPAR2(11) = 0x00000000
DEPCMDPAR1(11) = 0x00000000
DEPCMDPAR0(11) = 0x00000000
DEPCMD(11) = 0x00000000
DEPCMDPAR2(12) = 0x00000000
DEPCMDPAR1(12) = 0x00000000
DEPCMDPAR0(12) = 0x00000000
DEPCMD(12) = 0x00000000
DEPCMDPAR2(13) = 0x00000000
DEPCMDPAR1(13) = 0x00000000
DEPCMDPAR0(13) = 0x00000000
DEPCMD(13) = 0x00000000
DEPCMDPAR2(14) = 0x00000000
DEPCMDPAR1(14) = 0x00000000
DEPCMDPAR0(14) = 0x00000000
DEPCMD(14) = 0x00000000
DEPCMDPAR2(15) = 0x00000000
DEPCMDPAR1(15) = 0x00000000
DEPCMDPAR0(15) = 0x00000000
DEPCMD(15) = 0x00000000
DEPCMDPAR2(16) = 0x00000000
DEPCMDPAR1(16) = 0x00000000
DEPCMDPAR0(16) = 0x00000000
DEPCMD(16) = 0x00000000
DEPCMDPAR2(17) = 0x00000000
DEPCMDPAR1(17) = 0x00000000
DEPCMDPAR0(17) = 0x00000000
DEPCMD(17) = 0x00000000
DEPCMDPAR2(18) = 0x00000000
DEPCMDPAR1(18) = 0x00000000
DEPCMDPAR0(18) = 0x00000000
DEPCMD(18) = 0x00000000
DEPCMDPAR2(19) = 0x00000000
DEPCMDPAR1(19) = 0x00000000
DEPCMDPAR0(19) = 0x00000000
DEPCMD(19) = 0x00000000
DEPCMDPAR2(20) = 0x00000000
DEPCMDPAR1(20) = 0x00000000
DEPCMDPAR0(20) = 0x00000000
DEPCMD(20) = 0x00000000
DEPCMDPAR2(21) = 0x00000000
DEPCMDPAR1(21) = 0x00000000
DEPCMDPAR0(21) = 0x00000000
DEPCMD(21) = 0x00000000
DEPCMDPAR2(22) = 0x00000000
DEPCMDPAR1(22) = 0x00000000
DEPCMDPAR0(22) = 0x00000000
DEPCMD(22) = 0x00000000
DEPCMDPAR2(23) = 0x00000000
DEPCMDPAR1(23) = 0x00000000
DEPCMDPAR0(23) = 0x00000000
DEPCMD(23) = 0x00000000
DEPCMDPAR2(24) = 0x00000000
DEPCMDPAR1(24) = 0x00000000
DEPCMDPAR0(24) = 0x00000000
DEPCMD(24) = 0x00000000
DEPCMDPAR2(25) = 0x00000000
DEPCMDPAR1(25) = 0x00000000
DEPCMDPAR0(25) = 0x00000000
DEPCMD(25) = 0x00000000
DEPCMDPAR2(26) = 0x00000000
DEPCMDPAR1(26) = 0x00000000
DEPCMDPAR0(26) = 0x00000000
DEPCMD(26) = 0x00000000
DEPCMDPAR2(27) = 0x00000000
DEPCMDPAR1(27) = 0x00000000
DEPCMDPAR0(27) = 0x00000000
DEPCMD(27) = 0x00000000
DEPCMDPAR2(28) = 0x00000000
DEPCMDPAR1(28) = 0x00000000
DEPCMDPAR0(28) = 0x00000000
DEPCMD(28) = 0x00000000
DEPCMDPAR2(29) = 0x00000000
DEPCMDPAR1(29) = 0x00000000
DEPCMDPAR0(29) = 0x00000000
DEPCMD(29) = 0x00000000
DEPCMDPAR2(30) = 0x00000000
DEPCMDPAR1(30) = 0x00000000
DEPCMDPAR0(30) = 0x00000000
DEPCMD(30) = 0x00000000
DEPCMDPAR2(31) = 0x00000000
DEPCMDPAR1(31) = 0x00000000
DEPCMDPAR0(31) = 0x00000000
DEPCMD(31) = 0x00000000
OCFG = 0x00000000
OCTL = 0x00000040
OEVT = 0x80000000
OEVTEN = 0x00000000
OSTS = 0x0000201f
Thinh Nguyen
maintainerQuoted 3 lines · Ravineet Singh
Understood, my bad, will send a RFC patch in the future.
Regdumps (without the patch) are attached.
Please no top-post.
This looks like an issue with the integration of the controller and the phy/connector. Your phy vbus detection logic needs to properly assert the proper signals (e.g. vbusvalid/powerpresent etc.) on connection/disconnection detection.
It's best to fix it there. Forcing every U3/L2 transition to be treated as if it's a disconnection is problematic. If there's a real U3/L2 state change and then the host resumes, the device and host are out of sync.
I don't see a good workaround for this.
BR,
Thinh
Quoted 12 lines · Thinh Nguyen
Quoted 3 lines · Ravineet Singh
Understood, my bad, will send a RFC patch in the future.
Regdumps (without the patch) are attached.
Please no top-post.
This looks like an issue with the integration of the controller and the phy/connector. Your phy vbus detection logic needs to properly assert the proper signals (e.g. vbusvalid/powerpresent etc.) on connection/disconnection detection.
Quoted 8 lines
It's best to fix it there. Forcing every U3/L2 transition to be treated as if it's a disconnection is problematic. If there's a real U3/L2 state change and then the host resumes, the device and host are out of sync.
I don't see a good workaround for this.
BR,
Thinh
Understood, thanks!
BR
Ravineet