Remove single NFS client performance bottleneck: Only 4 nfsd active
Subsystems (2)
Hi,
I'm using the kernel NFS client/server and am trying to read as many small files per second as possible from a single NFS client, but seem to run into a bottleneck.
Maybe this is just a tunable that I am missing, because the CPUs on client and server side are mostly idle, the 100Gbit (RoCE) network links between client and server are also mostly idle and the NVMe drives in the server are also mostly idle (and the server has enough RAM to easily fit my test data set in the ext4/xfs page cache, but also a 2nd read of the data set from the RAM cache doesn't change the result much).
This is my test case:
# Create 1.6M 10KB files through 128 mdtest processes in different directories...
$ mpirun -hosts localhost -np 128 /path/to/mdtest -F -d /mnt/nfs/mdtest -i 1 -I 100 -z 1 -b 128 -L -u -w 10240 -e 10240 -C
# Read all the files through 128 mdtest processes (the case that matters primarily for my test)...
$ mpirun -hosts localhost -np 128 /path/to/mdtest -F -d /mnt/nfs/mdtest -i 1 -I 100 -z 1 -b 128 -L -u -w 10240 -e 10240 -E
The result is about 20,000 file reads per sec, so only ~200MB/s network throughput.
I noticed in "top" that only 4 nfsd processes are active, so I'm wondering why the load is not spread across more of my 64 /proc/fs/nfsd/threads, but even the few nfsd processes that are active use less than 50% of their core each. The CPUs are shown as >90% idle in "top" on client and server during the read phase.
I've tried:
* CentOS 7.5 and 7.6 kernels (3.10.0-...) on client and server; and Ubuntu 18 with 4.18 kernel on server side
* TCP & RDMA
* Mounted as NFSv3/v4.1/v4.2
* Increased tcp_slot_table_entries to 1024
...but all that didn't change the fact that only 4 nfsd processes are active on the server and thus I'm getting the same result already if /proc/fs/nfsd/threads is set to only 4 instead of 64.
Any pointer to how I can overcome this limit will be greatly appreciated.
Thanks in advance
Sven
Hi Sven-
Quoted 8 lines · Sven Breuner
Hi,
I'm using the kernel NFS client/server and am trying to read as many small files per second as possible from a single NFS client, but seem to run into a bottleneck.
Maybe this is just a tunable that I am missing, because the CPUs on client and server side are mostly idle, the 100Gbit (RoCE) network links between client and server are also mostly idle and the NVMe drives in the server are also mostly idle (and the server has enough RAM to easily fit my test data set in the ext4/xfs page cache, but also a 2nd read of the data set from the RAM cache doesn't change the result much).
Quoted 8 lines
This is my test case:
# Create 1.6M 10KB files through 128 mdtest processes in different directories...$ mpirun -hosts localhost -np 128 /path/to/mdtest -F -d /mnt/nfs/mdtest -i 1 -I 100 -z 1 -b 128 -L -u -w 10240 -e 10240 -C# Read all the files through 128 mdtest processes (the case that matters primarily for my test)...
$ mpirun -hosts localhost -np 128 /path/to/mdtest -F -d /mnt/nfs/mdtest -i 1 -I 100 -z 1 -b 128 -L -u -w 10240 -e 10240 -EThe result is about 20,000 file reads per sec, so only ~200MB/s network throughput.
What is the typical size of the NFS READ I/Os on the wire?
Are you sure your mpirun workload is generating enough parallelism?
Quoted 8 lines
I noticed in "top" that only 4 nfsd processes are active, so I'm wondering why the load is not spread across more of my 64
/proc/fs/nfsd/threads, but even the few nfsd processes that are active use less than 50% of their core each. The CPUs are shown as >90% idle in "top" on client and server during the read phase.I've tried:
* CentOS 7.5 and 7.6 kernels (3.10.0-...) on client and server; and Ubuntu 18 with 4.18 kernel on server side
* TCP & RDMA
* Mounted as NFSv3/v4.1/v4.2
* Increasedtcp_slot_table_entriesto 1024
Quoted 8 lines
...but all that didn't change the fact that only 4 nfsd processes are active on the server and thus I'm getting the same result already if
/proc/fs/nfsd/threadsis set to only 4 instead of 64.Any pointer to how I can overcome this limit will be greatly appreciated.
Thanks in advance
Sven
--
Chuck Lever
Quoted 18 lines · Chuck Lever
Hi Sven-
Quoted 12 lines · Sven Breuner
Hi,
I'm using the kernel NFS client/server and am trying to read as many small files per second as possible from a single NFS client, but seem to run into a bottleneck.
Maybe this is just a tunable that I am missing, because the CPUs on client and server side are mostly idle, the 100Gbit (RoCE) network links between client and server are also mostly idle and the NVMe drives in the server are also mostly idle (and the server has enough RAM to easily fit my test data set in the ext4/xfs page cache, but also a 2nd read of the data set from the RAM cache doesn't change the result much).
This is my test case:
# Create 1.6M 10KB files through 128 mdtest processes in different directories...$ mpirun -hosts localhost -np 128 /path/to/mdtest -F -d /mnt/nfs/mdtest -i 1 -I 100 -z 1 -b 128 -L -u -w 10240 -e 10240 -C
Quoted 8 lines
Quoted 4 lines
# Read all the files through 128 mdtest processes (the case that matters primarily for my test)...
$ mpirun -hosts localhost -np 128 /path/to/mdtest -F -d /mnt/nfs/mdtest -i 1 -I 100 -z 1 -b 128 -L -u -w 10240 -e 10240 -EThe result is about 20,000 file reads per sec, so only ~200MB/s network throughput.
What is the typical size of the NFS READ I/Os on the wire?
Are you sure your mpirun workload is generating enough parallelism?
A couple of other thoughts:
What's the client hardware like? NUMA? Fast memory? CPU count? Have you configured device interrupt affinity and used tuned to disable CPU sleep states, etc?
Have you properly configured your 100GbE switch and cards?
I have a Mellanox SN2100 here and two hosts with CX-5 Ethernet. The configuration of the cards and switch is critical to good performance.
Quoted 12 lines
Quoted 12 lines
I noticed in "top" that only 4 nfsd processes are active, so I'm wondering why the load is not spread across more of my 64
/proc/fs/nfsd/threads, but even the few nfsd processes that are active use less than 50% of their core each. The CPUs are shown as >90% idle in "top" on client and server during the read phase.I've tried:
* CentOS 7.5 and 7.6 kernels (3.10.0-...) on client and server; and Ubuntu 18 with 4.18 kernel on server side
* TCP & RDMA
* Mounted as NFSv3/v4.1/v4.2
* Increasedtcp_slot_table_entriesto 1024...but all that didn't change the fact that only 4 nfsd processes are active on the server and thus I'm getting the same result already if
/proc/fs/nfsd/threadsis set to only 4 instead of 64.Any pointer to how I can overcome this limit will be greatly appreciated.
Quoted 7 lines
Quoted 4 lines
Thanks in advance
Sven
--
Chuck Lever
--
Chuck Lever
Hi Chuck,
thanks for looking into this. (Answers inline...)
Chuck Lever wrote on 27.01.2020 15:12:
Quoted 17 lines
Quoted 17 lines · Chuck Lever
Hi Sven-
Quoted 12 lines · Sven Breuner
Hi,
I'm using the kernel NFS client/server and am trying to read as many small files per second as possible from a single NFS client, but seem to run into a bottleneck.
Maybe this is just a tunable that I am missing, because the CPUs on client and server side are mostly idle, the 100Gbit (RoCE) network links between client and server are also mostly idle and the NVMe drives in the server are also mostly idle (and the server has enough RAM to easily fit my test data set in the ext4/xfs page cache, but also a 2nd read of the data set from the RAM cache doesn't change the result much).
This is my test case:
# Create 1.6M 10KB files through 128 mdtest processes in different directories...$ mpirun -hosts localhost -np 128 /path/to/mdtest -F -d /mnt/nfs/mdtest -i 1 -I 100 -z 1 -b 128 -L -u -w 10240 -e 10240 -C
Quoted 5 lines
Quoted 5 lines
Quoted 4 lines
# Read all the files through 128 mdtest processes (the case that matters primarily for my test)...
$ mpirun -hosts localhost -np 128 /path/to/mdtest -F -d /mnt/nfs/mdtest -i 1 -I 100 -z 1 -b 128 -L -u -w 10240 -e 10240 -EThe result is about 20,000 file reads per sec, so only ~200MB/s network throughput.
What is the typical size of the NFS READ I/Os on the wire?
The application is fetching each full 10KB file in a single read op (so "read(fd, buf, 10240)" ) and NFS wsize/rsize is 512KB.
Quoted 1 line
Quoted 1 line
Are you sure your mpirun workload is generating enough parallelism?
Yes, MPI is only used to start the 128 processes and aggregate the performance results in the end. For the actual file read phase, all 128 processes run completely independent without any communication/synchronization. Each process is working in its own subdir with its own set of 10KB files. (Running the same test directly on the local xfs of the NFS server box results in ~350,000 10KB file reads per sec after cache drop and >1 mio 10KB file reads per sec from page cache. Just mentioning this for the sake of completeness to show that this is not hitting a limit on the server side.)
Quoted 3 lines
A couple of other thoughts:
What's the client hardware like? NUMA? Fast memory? CPU count?
Client and server are dual socket Intel Xeon E5-2690 v4 @ 2.60GHz (14 cores per socket plus hyper threading), all 4 memory channels per socket populated with fastest possible DIMMs (DDR4 2400).
Also tried pool_mode auto/global/pernode on server side.
Quoted 2 lines
Have you configured device interrupt affinity and used tuned to disable CPU sleep states, etc?
Yes, CPU power saving (frequency scaling) disabled. Tried tuned profiles latency-performance and and throughput-performance. Also tried irqbalance and mlnx_affinity.
All without any significant effect unfortunately.
Quoted 5 lines
Have you properly configured your 100GbE switch and cards?
I have a Mellanox SN2100 here and two hosts with CX-5 Ethernet. The configuration of the cards and switch is critical to good performance.
Yes, I can absolutely confirm that having this part of the config correct is critical for great performance :-) All configured with PFC and ECN and double-checked for packets to be tagged correctly and lossless in the RoCE case. The topology is simple: Client and server connected to same Mellanox switch, nothing else happening on the switch.
Quoted 25 lines
Quoted 12 lines
Quoted 12 lines
I noticed in "top" that only 4 nfsd processes are active, so I'm wondering why the load is not spread across more of my 64
/proc/fs/nfsd/threads, but even the few nfsd processes that are active use less than 50% of their core each. The CPUs are shown as >90% idle in "top" on client and server during the read phase.I've tried:
* CentOS 7.5 and 7.6 kernels (3.10.0-...) on client and server; and Ubuntu 18 with 4.18 kernel on server side
* TCP & RDMA
* Mounted as NFSv3/v4.1/v4.2
* Increasedtcp_slot_table_entriesto 1024...but all that didn't change the fact that only 4 nfsd processes are active on the server and thus I'm getting the same result already if
/proc/fs/nfsd/threadsis set to only 4 instead of 64.Quoted 8 lines
Quoted 6 lines
Any pointer to how I can overcome this limit will be greatly appreciated.
Thanks in advance
Sven
--
Chuck Lever--
Chuck Lever
Quoted 26 lines · Sven Breuner
Hi Chuck,
thanks for looking into this. (Answers inline...)
Chuck Lever wrote on 27.01.2020 15:12:
Quoted 17 lines
Quoted 17 lines · Chuck Lever
Hi Sven-
Quoted 12 lines · Sven Breuner
Hi,
I'm using the kernel NFS client/server and am trying to read as many small files per second as possible from a single NFS client, but seem to run into a bottleneck.
Maybe this is just a tunable that I am missing, because the CPUs on client and server side are mostly idle, the 100Gbit (RoCE) network links between client and server are also mostly idle and the NVMe drives in the server are also mostly idle (and the server has enough RAM to easily fit my test data set in the ext4/xfs page cache, but also a 2nd read of the data set from the RAM cache doesn't change the result much).
This is my test case:
# Create 1.6M 10KB files through 128 mdtest processes in different directories...$ mpirun -hosts localhost -np 128 /path/to/mdtest -F -d /mnt/nfs/mdtest -i 1 -I 100 -z 1 -b 128 -L -u -w 10240 -e 10240 -C
Quoted 6 lines
Quoted 5 lines
Quoted 5 lines
Quoted 4 lines
# Read all the files through 128 mdtest processes (the case that matters primarily for my test)...
$ mpirun -hosts localhost -np 128 /path/to/mdtest -F -d /mnt/nfs/mdtest -i 1 -I 100 -z 1 -b 128 -L -u -w 10240 -e 10240 -EThe result is about 20,000 file reads per sec, so only ~200MB/s network throughput.
What is the typical size of the NFS READ I/Os on the wire?
The application is fetching each full 10KB file in a single read op (so "
read(fd, buf, 10240)" ) and NFS wsize/rsize is 512KB.
512KB is not going to matter if every file contains only 10KB. This means 10KB READs. The I/O size is going to limit data throughput. 20KIOPS seems low for RDMA, but is about right for TCP.
If you see wire operations, then the client's page cache is not being used at all?
Quoted 8 lines
Quoted 1 line
Quoted 1 line
Are you sure your mpirun workload is generating enough parallelism?
Yes, MPI is only used to start the 128 processes and aggregate the performance results in the end. For the actual file read phase, all 128 processes run completely independent without any communication/synchronization. Each process is working in its own subdir with its own set of 10KB files. (Running the same test directly on the local xfs of the NFS server box results in ~350,000 10KB file reads per sec after cache drop and >1 mio 10KB file reads per sec from page cache. Just mentioning this for the sake of completeness to show that this is not hitting a limit on the server side.)
Quoted 3 lines
A couple of other thoughts:
What's the client hardware like? NUMA? Fast memory? CPU count?
Client and server are dual socket Intel Xeon E5-2690 v4 @ 2.60GHz (14 cores per socket plus hyper threading), all 4 memory channels per socket populated with fastest possible DIMMs (DDR4 2400).
One recommendation: Disable HT in the BIOS.
Quoted 1 line
Also tried
pool_modeauto/global/pernode on server side.
NUMA seems to matter more on the client than on the server.
Quoted 6 lines
Quoted 2 lines
Have you configured device interrupt affinity and used tuned to disable CPU sleep states, etc?
Yes, CPU power saving (frequency scaling) disabled. Tried tuned profiles latency-performance and and throughput-performance. Also tried irqbalance and
mlnx_affinity.All without any significant effect unfortunately.
And lspci -vvv confirms you are getting the right PCIe link settings on both systems?
Quoted 28 lines
Quoted 5 lines
Have you properly configured your 100GbE switch and cards?
I have a Mellanox SN2100 here and two hosts with CX-5 Ethernet. The configuration of the cards and switch is critical to good performance.
Yes, I can absolutely confirm that having this part of the config correct is critical for great performance :-) All configured with PFC and ECN and double-checked for packets to be tagged correctly and lossless in the RoCE case. The topology is simple: Client and server connected to same Mellanox switch, nothing else happening on the switch.
Quoted 22 lines
Quoted 12 lines
Quoted 12 lines
I noticed in "top" that only 4 nfsd processes are active, so I'm wondering why the load is not spread across more of my 64
/proc/fs/nfsd/threads, but even the few nfsd processes that are active use less than 50% of their core each. The CPUs are shown as >90% idle in "top" on client and server during the read phase.I've tried:
* CentOS 7.5 and 7.6 kernels (3.10.0-...) on client and server; and Ubuntu 18 with 4.18 kernel on server side
* TCP & RDMA
* Mounted as NFSv3/v4.1/v4.2
* Increasedtcp_slot_table_entriesto 1024...but all that didn't change the fact that only 4 nfsd processes are active on the server and thus I'm getting the same result already if
/proc/fs/nfsd/threadsis set to only 4 instead of 64.Quoted 8 lines
Quoted 6 lines
Any pointer to how I can overcome this limit will be greatly appreciated.
Thanks in advance
Sven
--
Chuck Lever--
Chuck Lever
--
Chuck Lever
Chuck Lever wrote on 27.01.2020 18:45:
Quoted 27 lines
Quoted 27 lines · Sven Breuner
Hi Chuck,
thanks for looking into this. (Answers inline...)
Chuck Lever wrote on 27.01.2020 15:12:
Quoted 19 lines
Quoted 19 lines · Chuck Lever
Hi Sven-
Quoted 15 lines · Sven Breuner
Hi,
I'm using the kernel NFS client/server and am trying to read as many small files per second as possible from a single NFS client, but seem to run into a bottleneck.
Maybe this is just a tunable that I am missing, because the CPUs on client and server side are mostly idle, the 100Gbit (RoCE) network links between client and server are also mostly idle and the NVMe drives in the server are also mostly idle (and the server has enough RAM to easily fit my test data set in the ext4/xfs page cache, but also a 2nd read of the data set from the RAM cache doesn't change the result much).
This is my test case:
# Create 1.6M 10KB files through 128 mdtest processes in different directories...$ mpirun -hosts localhost -np 128 /path/to/mdtest -F -d /mnt/nfs/mdtest -i 1 -I 100 -z 1 -b 128 -L -u -w 10240 -e 10240 -C# Read all the files through 128 mdtest processes (the case that matters primarily for my test)...
$ mpirun -hosts localhost -np 128 /path/to/mdtest -F -d /mnt/nfs/mdtest -i 1 -I 100 -z 1 -b 128 -L -u -w 10240 -e 10240 -E
Quoted 7 lines
Quoted 3 lines
Quoted 2 lines
Quoted 2 lines
Quoted 1 line
The result is about 20,000 file reads per sec, so only ~200MB/s network throughput.
What is the typical size of the NFS READ I/Os on the wire?
The application is fetching each full 10KB file in a single read op (so "
read(fd, buf, 10240)" ) and NFS wsize/rsize is 512KB.512KB is not going to matter if every file contains only 10KB. This means 10KB READs. The I/O size is going to limit data throughput. 20KIOPS seems low for RDMA, but is about right for TCP.
RDMA is about 30% faster (26K file reads per sec), but I'm more hoping for an order of magnitude increase.
By the way: Is there an NFSoRDMA equivalent for tcp_slot_table_entries to increase or is there no such limit in case of RDMA transport?
Quoted 2 lines
If you see wire operations, then the client's page cache is not being used at all?
I'm usually benchmarking after fresh client mount or "echo 3 > /proc/sys/vm/drop_caches", because the actual production data set will have many more files (multiple Terabytes) and thus won't fit in RAM.
Quoted 10 lines
Quoted 9 lines
Quoted 3 lines
Quoted 3 lines
Are you sure your mpirun workload is generating enough parallelism?
Yes, MPI is only used to start the 128 processes and aggregate the performance results in the end. For the actual file read phase, all 128 processes run completely independent without any communication/synchronization. Each process is working in its own subdir with its own set of 10KB files. (Running the same test directly on the local xfs of the NFS server box results in ~350,000 10KB file reads per sec after cache drop and >1 mio 10KB file reads per sec from page cache. Just mentioning this for the sake of completeness to show that this is not hitting a limit on the server side.)
Quoted 3 lines
A couple of other thoughts:
What's the client hardware like? NUMA? Fast memory? CPU count?
Client and server are dual socket Intel Xeon E5-2690 v4 @ 2.60GHz (14 cores per socket plus hyper threading), all 4 memory channels per socket populated with fastest possible DIMMs (DDR4 2400).
One recommendation: Disable HT in the BIOS.
Thanks for the recommendation. Tried, but no significant difference.
Quoted 2 lines
Quoted 1 line
Also tried
pool_modeauto/global/pernode on server side.NUMA seems to matter more on the client than on the server.
mpirun can also bind the mdtest processes to NUMA zones, but also no significant difference for that.
Quoted 9 lines
Quoted 7 lines
Quoted 4 lines
Have you configured device interrupt affinity and used tuned to disable CPU sleep states, etc?
Yes, CPU power saving (frequency scaling) disabled. Tried tuned profiles latency-performance and and throughput-performance. Also tried irqbalance and
mlnx_affinity.All without any significant effect unfortunately.
And lspci -vvv confirms you are getting the right PCIe link settings on both systems?
Yes. I can also see >11GB/s network throughput between client and server through e.g. ib_send_bw.
Actually, the client and server each have two 100Gbit RoCE NICs, but it seems like there isn't a way currently to get the NFS client to spread the communication across two RDMA interfaces for a single mountpoint.
Assuming the hardware is not the limit, is there any software limit for parallelism in the NFS client? So if an application on an NFS client can generates 128 concurrent open/read/close (from 128 threads) to 128 different files in the NFS mountpoint, will the NFS client then actually send 128 concurrent open/read/close over the wire or will it e.g. limit for some reason to only 4 or 8 concurrent requests and the rest will be queued until one of the first 4/8/... requests has received a reply - e.g. because there is only 1 pending reply allowed per connection and a client does not establish more than 4/8/... connections to the same server? And same question on the NFS server side: If a client sends 128 concurrent reads over the wire and the knfsd has 128 threads, will it actually work on all those 128 reads in parallel or is there a limit in the server that e.g. maps requests from the same client to a maximum of 4/8/... threads, no matter how many more threads the knfsd has available?
Thanks a lot for your help
Sven
Quoted 34 lines
Quoted 29 lines
Quoted 7 lines
Have you properly configured your 100GbE switch and cards?
I have a Mellanox SN2100 here and two hosts with CX-5 Ethernet. The configuration of the cards and switch is critical to good performance.
Yes, I can absolutely confirm that having this part of the config correct is critical for great performance :-) All configured with PFC and ECN and double-checked for packets to be tagged correctly and lossless in the RoCE case. The topology is simple: Client and server connected to same Mellanox switch, nothing else happening on the switch.
Quoted 21 lines
Quoted 11 lines
Quoted 11 lines
I noticed in "top" that only 4 nfsd processes are active, so I'm wondering why the load is not spread across more of my 64
/proc/fs/nfsd/threads, but even the few nfsd processes that are active use less than 50% of their core each. The CPUs are shown as >90% idle in "top" on client and server during the read phase.I've tried:
* CentOS 7.5 and 7.6 kernels (3.10.0-...) on client and server; and Ubuntu 18 with 4.18 kernel on server side
* TCP & RDMA
* Mounted as NFSv3/v4.1/v4.2
* Increasedtcp_slot_table_entriesto 1024...but all that didn't change the fact that only 4 nfsd processes are active on the server and thus I'm getting the same result already if
/proc/fs/nfsd/threadsis set to only 4 instead of 64.Quoted 8 lines
Quoted 6 lines
Any pointer to how I can overcome this limit will be greatly appreciated.
Thanks in advance
Sven
--
Chuck Lever--
Chuck Lever--
Chuck Lever
Quoted 33 lines · Sven Breuner
Chuck Lever wrote on 27.01.2020 18:45:
Quoted 27 lines
Quoted 27 lines · Sven Breuner
Hi Chuck,
thanks for looking into this. (Answers inline...)
Chuck Lever wrote on 27.01.2020 15:12:
Quoted 19 lines
Quoted 19 lines · Chuck Lever
Hi Sven-
Quoted 15 lines · Sven Breuner
Hi,
I'm using the kernel NFS client/server and am trying to read as many small files per second as possible from a single NFS client, but seem to run into a bottleneck.
Maybe this is just a tunable that I am missing, because the CPUs on client and server side are mostly idle, the 100Gbit (RoCE) network links between client and server are also mostly idle and the NVMe drives in the server are also mostly idle (and the server has enough RAM to easily fit my test data set in the ext4/xfs page cache, but also a 2nd read of the data set from the RAM cache doesn't change the result much).
This is my test case:
# Create 1.6M 10KB files through 128 mdtest processes in different directories...$ mpirun -hosts localhost -np 128 /path/to/mdtest -F -d /mnt/nfs/mdtest -i 1 -I 100 -z 1 -b 128 -L -u -w 10240 -e 10240 -C# Read all the files through 128 mdtest processes (the case that matters primarily for my test)...
$ mpirun -hosts localhost -np 128 /path/to/mdtest -F -d /mnt/nfs/mdtest -i 1 -I 100 -z 1 -b 128 -L -u -w 10240 -e 10240 -E
Quoted 8 lines
Quoted 7 lines
Quoted 3 lines
Quoted 2 lines
Quoted 2 lines
Quoted 1 line
The result is about 20,000 file reads per sec, so only ~200MB/s network throughput.
What is the typical size of the NFS READ I/Os on the wire?
The application is fetching each full 10KB file in a single read op (so "
read(fd, buf, 10240)" ) and NFS wsize/rsize is 512KB.512KB is not going to matter if every file contains only 10KB. This means 10KB READs. The I/O size is going to limit data throughput. 20KIOPS seems low for RDMA, but is about right for TCP.
RDMA is about 30% faster (26K file reads per sec), but I'm more hoping for an order of magnitude increase.
Not an unreasonable hope. Here's a simple fio test I ran on my 100GbE systems with NFSv3:
fio-test: (g=0): rw=randread, bs=(R) 4096B-4096B, (W) 4096B-4096B, (T) 4096B-4096B, ioengine=libaio, iodepth=1024
...
fio-3.14
Starting 4 processes
fio-test: Laying out IO file (1 file / 1024MiB)
fio-test: Laying out IO file (1 file / 1024MiB)
fio-test: Laying out IO file (1 file / 1024MiB)
fio-test: Laying out IO file (1 file / 1024MiB)
Jobs: 4 (f=4): [r(4)][100.0%][r=1092MiB/s][r=280k IOPS][eta 00m:00s]
fio-test: (groupid=0, jobs=4): err= 0: pid=3075643: Tue Jan 28 19:27:10 2020
read: IOPS=280k, BW=1094MiB/s (1147MB/s)(32.0GiB/30005msec)
slat (nsec): min=1516, max=83293k, avg=7696.22, stdev=218022.20
clat (usec): min=46, max=143098, avg=14618.22, stdev=11253.38
lat (usec): min=50, max=143105, avg=14626.26, stdev=11256.38
clat percentiles (msec):
| 1.00th=[ 3], 5.00th=[ 4], 10.00th=[ 5], 20.00th=[ 7],
| 30.00th=[ 8], 40.00th=[ 10], 50.00th=[ 12], 60.00th=[ 14],
| 70.00th=[ 17], 80.00th=[ 21], 90.00th=[ 28], 95.00th=[ 36],
| 99.00th=[ 60], 99.50th=[ 71], 99.90th=[ 90], 99.95th=[ 94],
| 99.99th=[ 108]
bw ( MiB/s): min= 728, max= 1795, per=99.96%, avg=1093.10, stdev=55.40, samples=240
iops : min=186436, max=459578, avg=279833.92, stdev=14183.03, samples=240
lat (usec) : 50=0.01%, 100=0.01%, 250=0.03%, 500=0.08%, 750=0.08%
lat (usec) : 1000=0.08%
lat (msec) : 2=0.47%, 4=4.93%, 10=35.53%, 20=38.41%, 50=18.62%
lat (msec) : 100=1.75%, 250=0.03%
cpu : usr=10.66%, sys=17.51%, ctx=1627222, majf=0, minf=4136
IO depths : 1=0.1%, 2=0.1%, 4=0.1%, 8=0.1%, 16=0.1%, 32=0.1%, >=64=100.0%
submit : 0=0.0%, 4=100.0%, 8=0.0%, 16=0.0%, 32=0.0%, 64=0.0%, >=64=0.0%
complete : 0=0.0%, 4=100.0%, 8=0.0%, 16=0.0%, 32=0.0%, 64=0.0%, >=64=0.1%
issued rwts: total=8400192,0,0,0 short=0,0,0,0 dropped=0,0,0,0
latency : target=0, window=0, percentile=100.00%, depth=1024Run status group 0 (all jobs):
READ: bw=1094MiB/s (1147MB/s), 1094MiB/s-1094MiB/s (1147MB/s-1147MB/s), io=32.0GiB (34.4GB), run=30005-30005msec
It achieves better than a quarter-million 4KB read IOPS.
However I do not believe there is an open/close with each I/O in this test; each thread opens one of the test files, and then simply streams reads to it.
Quoted 1 line
By the way: Is there an NFSoRDMA equivalent for
tcp_slot_table_entriesto increase or is there no such limit in case of RDMA transport?
[cel@morisot ~]$ cat /proc/sys/sunrpc/tcp_slot_table_entries 2
[cel@morisot ~]$ cat /proc/sys/sunrpc/tcp_max_slot_table_entries 65536
[cel@morisot ~]$ cat /proc/sys/sunrpc/rdma_slot_table_entries 128
[cel@morisot ~]$
The tcp_slot_table_entries file controls the number of pre-allocated rpc_rqst's per transport. After 2 are in use, the transport uses kmalloc and kfree for the others.
The tcp_max_slot_table_entries file caps the total number of rpc_rqst's allowed per transport. The default setting is already quite large.
The rdma_slot_table_entries file caps the number of RPC-over-RDMA credits the client supports. The Linux server grants at most 32 credits. That number has increased to 64 credits in recent kernels.
The kernel also has a control on the server to set the number of credits it will grant:
[cel@bazille linux]$ cat /proc/sys/sunrpc/svc_rdma/max_requests 64
[cel@bazille linux]$
These two systems will use no more than 64 credits per connection.
Quoted 3 lines
Quoted 2 lines
If you see wire operations, then the client's page cache is not being used at all?
I'm usually benchmarking after fresh client mount or "echo 3 >
/proc/sys/vm/drop_caches", because the actual production data set will have many more files (multiple Terabytes) and thus won't fit in RAM.
In the server's RAM? If that's the case, then your durable storage will be the main bottleneck.
Quoted 5 lines
Quoted 5 lines
Quoted 5 lines
Quoted 1 line
Quoted 1 line
Are you sure your mpirun workload is generating enough parallelism?
Yes, MPI is only used to start the 128 processes and aggregate the performance results in the end. For the actual file read phase, all 128 processes run completely independent without any communication/synchronization. Each process is working in its own subdir with its own set of 10KB files. (Running the same test directly on the local xfs of the NFS server box results in ~350,000 10KB file reads per sec after cache drop and >1 mio 10KB file reads per sec from page cache. Just mentioning this for the sake of completeness to show that this is not hitting a limit on the server side.)
Quoted 2 lines
A couple of other thoughts:
Quoted 7 lines
Quoted 3 lines
Quoted 2 lines
Quoted 1 line
What's the client hardware like? NUMA? Fast memory? CPU count?
Client and server are dual socket Intel Xeon E5-2690 v4 @ 2.60GHz (14 cores per socket plus hyper threading), all 4 memory channels per socket populated with fastest possible DIMMs (DDR4 2400).
One recommendation: Disable HT in the BIOS.
Thanks for the recommendation. Tried, but no significant difference.
Quoted 2 lines
Quoted 1 line
Also tried
pool_modeauto/global/pernode on server side.NUMA seems to matter more on the client than on the server.
mpirun can also bind the mdtest processes to NUMA zones, but also no significant difference for that.
Keep the processes on the same node as the NIC and its interrupt vectors. Again, not likely to give a 10x boost in IOPS, but it will help once you figure out the main issue.
Quoted 11 lines
Quoted 7 lines
Quoted 5 lines
Quoted 2 lines
Have you configured device interrupt affinity and used tuned to disable CPU sleep states, etc?
Yes, CPU power saving (frequency scaling) disabled. Tried tuned profiles latency-performance and and throughput-performance. Also tried irqbalance and
mlnx_affinity.All without any significant effect unfortunately.
And lspci -vvv confirms you are getting the right PCIe link settings on both systems?
Yes. I can also see >11GB/s network throughput between client and server through e.g.
ib_send_bw.Actually, the client and server each have two 100Gbit RoCE NICs, but it seems like there isn't a way currently to get the NFS client to spread the communication across two RDMA interfaces for a single mountpoint.
That's correct. You might try bonding the two NICs.
However, in general a single RDMA NIC should enable much better throughput than a non-offloaded NIC.
Quoted 1 line
Assuming the hardware is not the limit, is there any software limit for parallelism in the NFS client?
No architected limit that I'm aware of. Lock contention can certainly be a problem, though.
Also, if your kernel builds have Kernel Hacking options enabled, that can have a considerable impact on throughput. Memory, lock, or data structure debugging options will have an effect.
NFSv4.0 open owners maybe? Though you said your test results do not seem to depend on the NFS version.
NFSv3 does not have on-the-wire OPEN and CLOSE, but IIUC it does force a GETATTR operation to check the file's mtime at each open(2) and close(2). I wonder if the "nocto" mount option would help the NFSv3 results?
Quoted 1 line
So if an application on an NFS client can generates 128 concurrent open/read/close (from 128 threads) to 128 different files in the NFS mountpoint, will the NFS client then actually send 128 concurrent open/read/close over the wire or will it e.g. limit for some reason to only 4 or 8 concurrent requests and the rest will be queued until one of the first 4/8/... requests has received a reply - e.g. because there is only 1 pending reply allowed per connection and a client does not establish more than 4/8/... connections to the same server?
A connection can have as many concurrent pending replies as there are outstanding calls.
With TCP, you can use tcpdump to look at wire behavior to see if there are obvious problems.
Quoted 1 line
And same question on the NFS server side: If a client sends 128 concurrent reads over the wire and the knfsd has 128 threads, will it actually work on all those 128 reads in parallel or is there a limit in the server that e.g. maps requests from the same client to a maximum of 4/8/... threads, no matter how many more threads the knfsd has available?
Each nfsd thread handles one RPC. If there are 128 ingress NFS READS and 128 threads, the kernel will try to use all available threads.
Quoted 35 lines
Thanks a lot for your help
Sven
Quoted 31 lines
Quoted 29 lines
Quoted 7 lines
Have you properly configured your 100GbE switch and cards?
I have a Mellanox SN2100 here and two hosts with CX-5 Ethernet. The configuration of the cards and switch is critical to good performance.
Yes, I can absolutely confirm that having this part of the config correct is critical for great performance :-) All configured with PFC and ECN and double-checked for packets to be tagged correctly and lossless in the RoCE case. The topology is simple: Client and server connected to same Mellanox switch, nothing else happening on the switch.
Quoted 21 lines
Quoted 11 lines
Quoted 11 lines
I noticed in "top" that only 4 nfsd processes are active, so I'm wondering why the load is not spread across more of my 64
/proc/fs/nfsd/threads, but even the few nfsd processes that are active use less than 50% of their core each. The CPUs are shown as >90% idle in "top" on client and server during the read phase.I've tried:
* CentOS 7.5 and 7.6 kernels (3.10.0-...) on client and server; and Ubuntu 18 with 4.18 kernel on server side
* TCP & RDMA
* Mounted as NFSv3/v4.1/v4.2
* Increasedtcp_slot_table_entriesto 1024...but all that didn't change the fact that only 4 nfsd processes are active on the server and thus I'm getting the same result already if
/proc/fs/nfsd/threadsis set to only 4 instead of 64.Quoted 8 lines
Quoted 6 lines
Any pointer to how I can overcome this limit will be greatly appreciated.
Thanks in advance
Sven
--
Chuck Lever--
Chuck Lever--
Chuck Lever
--
Chuck Lever