Skip to contentSkip to conversation

sdhci: fix SDMA boundary bug

PATCH In review Tao Ding 3 participants 8 messages Jul 15 – Sep 3

Subsystems (2)
lore
Share & tools
lore

Tao Ding

author
#0 lore raw

v7 cover sdhci: fix SDMA boundary bug

Hi all,

This series fixes an SDMA multi-block transfer bug in the generic SDHCI controller.

The previous series was posted here:
https://lore.kernel.org/qemu-devel/[email protected]/

Thanks

Changes in v6->v7:
* patch 1/2. The addition of pre_load and post_load methods to handling of migration from older versions.
* patch 2/2 is unchanged. keep Reviewed-by Bin Meng.

Tao Ding (2):
hw/sd: sdhci: Fix SDMA boundary bug
qtest: add xilinx-zynq SDHCI sdma test

 hw/sd/sdhci.c                        |  54 +++++++-
 include/hw/sd/sdhci.h                |   2 +
 tests/qtest/meson.build              |   1 +
 tests/qtest/xilinx-zynq-sdhci-test.c | 178 +++++++++++++++++++++++++++
 4 files changed, 234 insertions(+), 1 deletion(-)
 create mode 100644 tests/qtest/xilinx-zynq-sdhci-test.c

base-commit: 608ad9307d5b4797d2254ee3a4bad2bc8c8bcbae

Signature · 1 line
2.43.0
author
#1 lore raw

PATCH v7 1/2 hw/sd: sdhci: Fix SDMA boundary bug

During SDMA transfers, the controller raises an interrupt at buffer boundaries to request a system address update. The host driver will rewrite the SDHC_SYSAD register. (according to PartA2_SD_Host_Controller_Simplified_Specification_Ver2.00.pdf section 2.2.1) However, the current code will ignore write operations to SDHC_SYSAD.

To fix this bug, when SDMA encounters a boundary, a state is set to record it.
In this state, SDHC_SYSAD can be written. In other cases, it is still protected by TRANSFERRING_DATA.

Meanwhile, a subsection has been added for migration.

---
This bug may be encountered when using uboot with SDMA functionality, and can be reproduced by following the steps below. Uboot test:
1. Prepare zImage, uboot and rootfs.cpio.gz, make sure uboot config (MMC_SDHCI_SDMA=y).
for more detail, can obtained "https://lore.kernel.org/qemu-devel/[email protected]/T/#mcdf231e6bd762903f8393bf93253cbcb12ececcf"
2. ./qemu-system-aarch64 -M xilinx-zynq-a9 -machine boot-mode=sd -m 1024 -display none -serial null -serial stdio -monitor none \
-device loader,file=u-boot-dtb.bin,addr=0x04000000,cpu-num=0 \
-drive file=zynq-sd.img,format=raw,if=sd -D qemu.log

After applying the fix, success load sd card:

U-Boot 2026.07-rc4-g1e80ee41441c (Jun 15 2026 - 19:05:05 +0800)

Model: Xilinx ZC702 board
DRAM:  ECC disabled 1 GiB
Core:  33 devices, 21 uclasses, devicetree: board
Flash: 0 Bytes
NAND:  0 MiB
MMC:   mmc@e0100000: 0

Loading Environment from FAT... *** Error - No Valid Environment Area found *** Warning - bad env area, using default environment

In:    serial@e0001000
Out:   serial@e0001000
Err:   serial@e0001000

Net:
ZYNQ GEM: e000b000, mdio bus e000b000, phyaddr 7, interface rgmii-id

Warning: ethernet@e000b000 (eth0) using random MAC address - 4a:63:5a:a4:d3:6b
eth0: ethernet@e000b000
Hit any key to stop autoboot: 0
Zynq> fatload mmc 0 ${kernel_addr_r} zImage
10838528 bytes read in 4316 ms (2.4 MiB/s)
Zynq> fatload mmc 0 ${ramdisk_addr_r} rootfs-arm32.cpio.gz
406531 bytes read in 199 ms (1.9 MiB/s)
Zynq> setenv ramdisk_size ${filesize}
Zynq> fatload mmc 0 ${fdt_addr_r} zynq-zc702.dtb
15754 bytes read in 21 ms (732.4 KiB/s)
Zynq> setenv bootargs console=ttyPS0,115200 earlycon ignore_loglevel rdinit=/init Zynq> bootz ${kernel_addr_r} ${ramdisk_addr_r}:${ramdisk_size} ${fdt_addr_r} Kernel image @ 0x2000000 [ 0x000000 - 0xa56200 ]
## Flattened Device Tree blob at 01f00000
Booting using the fdt blob at 0x1f00000
Working FDT set to 1f00000
Loading Ramdisk to 2ff9c000, end 2ffff403 ... OK
Loading Device Tree to 2ff95000, end 2ff9bd89 ... OK
Working FDT set to 2ff95000

Starting kernel ...

 hw/sd/sdhci.c         | 54 ++++++++++++++++++++++++++++++++++++++++++-
 include/hw/sd/sdhci.h |  2 ++
 2 files changed, 55 insertions(+), 1 deletion(-)
hw/sd/sdhci.c +53 -1
index c86dfa281f..55a4abdd72 100644
@@ -307,6 +307,7 @@ static void sdhci_reset(SDHCIState *s)
     s->data_count = 0;
     s->stopped_state = sdhc_not_stopped;
     s->pending_insert_state = false;
+    s->sdma_boundary_paused = false;
     if (object_dynamic_cast(OBJECT(s), TYPE_FSL_ESDHC_BE) ||
             object_dynamic_cast(OBJECT(s), TYPE_FSL_ESDHC_LE)) {
         s->norintstsen = 0x013f;
@@ -414,6 +415,7 @@ static void sdhci_end_transfer(SDHCIState *s)
         s->norintsts |= SDHC_NIS_TRSCMP;
     }
 
+    s->sdma_boundary_paused = false;
     sdhci_update_irq(s);
 }
 
@@ -681,6 +683,7 @@ static void sdhci_sdma_transfer_multi_blocks(SDHCIState *s)
     if (s->blkcnt == 0) {
         sdhci_end_transfer(s);
     } else {
+        s->sdma_boundary_paused = true;
         sdhci_update_irq(s);
     }
 }
@@ -717,6 +720,15 @@ static void sdhci_sdma_transfer(SDHCIState *s)
     }
 }
 
+static bool sdhci_sdma_transfer_active(SDHCIState *s)
+{
+    return TRANSFERRING_DATA(s->prnsts) &&
+            (s->trnmod & SDHC_TRNS_DMA) &&
+            s->blkcnt &&
+            (s->blksize & BLOCK_SIZE_MASK) &&
+            SDHC_DMA_TYPE(s->hostctl1) == SDHC_CTRL_SDMA;
+}
+
 typedef struct ADMADescr {
     hwaddr addr;
     uint16_t length;
@@ -1164,6 +1176,7 @@ static inline void sdhci_reset_write(SDHCIState *s, uint8_t value)
                 SDHC_DATA_INHIBIT | SDHC_DAT_LINE_ACTIVE);
         s->blkgap &= ~(SDHC_STOP_AT_GAP_REQ | SDHC_CONTINUE_REQ);
         s->stopped_state = sdhc_not_stopped;
+        s->sdma_boundary_paused = false;
         s->norintsts &= ~(SDHC_NIS_WBUFRDY | SDHC_NIS_RBUFRDY |
                 SDHC_NIS_DMA | SDHC_NIS_TRSCMP | SDHC_NIS_BLKGAP);
         break;
@@ -1185,7 +1198,7 @@ sdhci_write(void *opaque, hwaddr offset, uint64_t val, unsigned size)
 
     switch (offset & ~0x3) {
     case SDHC_SYSAD:
-        if (!TRANSFERRING_DATA(s->prnsts)) {
+        if (!TRANSFERRING_DATA(s->prnsts) || s->sdma_boundary_paused) {
             s->sdmasysad = (s->sdmasysad & mask) | value;
             MASKED_WRITE(s->sdmasysad, mask, value);
             /* Writing to last byte of sdmasysad might trigger transfer */
@@ -1464,6 +1477,31 @@ static bool sdhci_pending_insert_vmstate_needed(void *opaque)
     return s->pending_insert_state;
 }
 
+static bool sdhci_sdma_boundary_paused_vmstate_needed(void *opaque)
+{
+    SDHCIState *s = opaque;
+
+    return s->sdma_boundary_paused;
+}
+
+static int sdhci_pre_load(void *opaque)
+{
+    SDHCIState *s = opaque;
+
+    s->sdma_boundary_paused = false;
+    return 0;
+}
+
+static int sdhci_post_load(void *opaque, int version_id)
+{
+    SDHCIState *s = opaque;
+
+    if (!s->sdma_boundary_paused) {
+        s->sdma_boundary_paused = sdhci_sdma_transfer_active(s);
+    }
+    return 0;
+}
+
 static const VMStateDescription sdhci_pending_insert_vmstate = {
     .name = "sdhci/pending-insert",
     .version_id = 1,
@@ -1475,10 +1513,23 @@ static const VMStateDescription sdhci_pending_insert_vmstate = {
     },
 };
 
+static const VMStateDescription sdhci_sdma_boundary_paused_vmstate = {
+    .name = "sdhci/sdma_boundary_paused",
+    .version_id = 1,
+    .minimum_version_id = 1,
+    .needed = sdhci_sdma_boundary_paused_vmstate_needed,
+    .fields = (const VMStateField[]) {
+        VMSTATE_BOOL(sdma_boundary_paused, SDHCIState),
+        VMSTATE_END_OF_LIST()
+    },
+};
+
 const VMStateDescription sdhci_vmstate = {
     .name = "sdhci",
     .version_id = 1,
     .minimum_version_id = 1,
+    .pre_load = sdhci_pre_load,
+    .post_load = sdhci_post_load,
     .fields = (const VMStateField[]) {
         VMSTATE_UINT32(sdmasysad, SDHCIState),
         VMSTATE_UINT16(blksize, SDHCIState),
@@ -1512,6 +1563,7 @@ const VMStateDescription sdhci_vmstate = {
     },
     .subsections = (const VMStateDescription * const []) {
         &sdhci_pending_insert_vmstate,
+        &sdhci_sdma_boundary_paused_vmstate,
         NULL
     },
 };
include/hw/sd/sdhci.h +2 -0
index a9da6203fc..c485277744 100644
@@ -103,6 +103,8 @@ struct SDHCIState {
      * to be protected. Set wp_inverted to invert the signal.
      */
     bool wp_inverted;
+    /* Indicate that SDMA transfer is paused due to hitting the boundary */
+    bool sdma_boundary_paused;
 };
 typedef struct SDHCIState SDHCIState;
 
Signature · 1 line
2.43.0
Reviewed-by on v7 1/2
#2 lore raw

Re: [PATCH v7 1/2] hw/sd: sdhci: Fix SDMA boundary bug

Quoted 63 lines · Tao Ding

During SDMA transfers, the controller raises an interrupt at buffer boundaries to request a system address update. The host driver will rewrite the SDHC_SYSAD register. (according to PartA2_SD_Host_Controller_Simplified_Specification_Ver2.00.pdf section 2.2.1) However, the current code will ignore write operations to SDHC_SYSAD.

To fix this bug, when SDMA encounters a boundary, a state is set to record it.
In this state, SDHC_SYSAD can be written. In other cases, it is still protected by TRANSFERRING_DATA.

Meanwhile, a subsection has been added for migration.

---
This bug may be encountered when using uboot with SDMA functionality, and can be reproduced by following the steps below. Uboot test:
1. Prepare zImage, uboot and rootfs.cpio.gz, make sure uboot config (MMC_SDHCI_SDMA=y).
for more detail, can obtained "https://lore.kernel.org/qemu-devel/[email protected]/T/#mcdf231e6bd762903f8393bf93253cbcb12ececcf"
2. ./qemu-system-aarch64 -M xilinx-zynq-a9 -machine boot-mode=sd -m 1024 -display none -serial null -serial stdio -monitor none \
-device loader,file=u-boot-dtb.bin,addr=0x04000000,cpu-num=0 \
-drive file=zynq-sd.img,format=raw,if=sd -D qemu.log

After applying the fix, success load sd card:

U-Boot 2026.07-rc4-g1e80ee41441c (Jun 15 2026 - 19:05:05 +0800)

Model: Xilinx ZC702 board
DRAM:  ECC disabled 1 GiB
Core:  33 devices, 21 uclasses, devicetree: board
Flash: 0 Bytes
NAND:  0 MiB
MMC:   mmc@e0100000: 0

Loading Environment from FAT... *** Error - No Valid Environment Area found *** Warning - bad env area, using default environment

In:    serial@e0001000
Out:   serial@e0001000
Err:   serial@e0001000

Net:
ZYNQ GEM: e000b000, mdio bus e000b000, phyaddr 7, interface rgmii-id

Warning: ethernet@e000b000 (eth0) using random MAC address - 4a:63:5a:a4:d3:6b
eth0: ethernet@e000b000
Hit any key to stop autoboot: 0
Zynq> fatload mmc 0 ${kernel_addr_r} zImage
10838528 bytes read in 4316 ms (2.4 MiB/s)
Zynq> fatload mmc 0 ${ramdisk_addr_r} rootfs-arm32.cpio.gz
406531 bytes read in 199 ms (1.9 MiB/s)
Zynq> setenv ramdisk_size ${filesize}
Zynq> fatload mmc 0 ${fdt_addr_r} zynq-zc702.dtb
15754 bytes read in 21 ms (732.4 KiB/s)
Zynq> setenv bootargs console=ttyPS0,115200 earlycon ignore_loglevel rdinit=/init Zynq> bootz ${kernel_addr_r} ${ramdisk_addr_r}:${ramdisk_size} ${fdt_addr_r} Kernel image @ 0x2000000 [ 0x000000 - 0xa56200 ]
## Flattened Device Tree blob at 01f00000
Booting using the fdt blob at 0x1f00000
Working FDT set to 1f00000
Loading Ramdisk to 2ff9c000, end 2ffff403 ... OK
Loading Device Tree to 2ff95000, end 2ff9bd89 ... OK
Working FDT set to 2ff95000

Quoted 6 lines

Starting kernel ...

 hw/sd/sdhci.c         | 54 ++++++++++++++++++++++++++++++++++++++++++-
 include/hw/sd/sdhci.h |  2 ++
 2 files changed, 55 insertions(+), 1 deletion(-)
#3 lore raw

Re: [PATCH v7 1/2] hw/sd: sdhci: Fix SDMA boundary bug

In reply to Tao Ding
Quoted 25 lines · Tao Ding

During SDMA transfers, the controller raises an interrupt at buffer boundaries to request a system address update. The host driver will rewrite the SDHC_SYSAD register. (according to PartA2_SD_Host_Controller_Simplified_Specification_Ver2.00.pdf section 2.2.1) However, the current code will ignore write operations to SDHC_SYSAD.

To fix this bug, when SDMA encounters a boundary, a state is set to record it.
In this state, SDHC_SYSAD can be written. In other cases, it is still protected by TRANSFERRING_DATA.

Meanwhile, a subsection has been added for migration.

---

hw/sd/sdhci.c +8 -0
+static bool sdhci_sdma_transfer_active(SDHCIState *s)
+{
+    return TRANSFERRING_DATA(s->prnsts) &&
+            (s->trnmod & SDHC_TRNS_DMA) &&
+            s->blkcnt &&
+            (s->blksize & BLOCK_SIZE_MASK) &&
+            SDHC_DMA_TYPE(s->hostctl1) == SDHC_CTRL_SDMA;
+}

hw/sd/sdhci.c sdhci_write(void *opaque, hwaddr offset, uint64_t val, unsigned size) · line 1204

Quoted 8 lines
hw/sd/sdhci.c +1 -1
@@ -1185,7 +1198,7 @@ sdhci_write(void *opaque, hwaddr offset, uint64_t val, unsigned size)
 
      switch (offset & ~0x3) {
      case SDHC_SYSAD:
-        if (!TRANSFERRING_DATA(s->prnsts)) {
+        if (!TRANSFERRING_DATA(s->prnsts) || s->sdma_boundary_paused) {
              s->sdmasysad = (s->sdmasysad & mask) | value;
              MASKED_WRITE(s->sdmasysad, mask, value);
              /* Writing to last byte of sdmasysad might trigger transfer */

So the SYSAD write-protection guard didn't account for the boundary-pause state, silently dropping the driver's continuation write and stalling SDMA transfers forever once a boundary was crossed, OK.

Series queued!

author
#4 lore raw

PATCH v7 2/2 qtest: add xilinx-zynq SDHCI sdma test

In reply to Tao Ding

Add a standalone qtest for the SDHCI controller on the xilinx-zynq-a9 machine.

The test covers the SDMA boundary continuation case for a multi-block read. After the controller stops at a boundary, software updates SYSAD to continue the transfer. This verifies the generic SDHCI behavior that previously failed when the continuation SYSAD write was ignored and the transfer stalled.

---
Build:
mkdir build
cd build
../configure --target-list="arm-softmmu" --disable-slirp --enable-debug --disable-werror make -j4

Run:
QTEST_QEMU_BINARY=./qemu-system-arm \
tests/qtest/xilinx-zynq-sdhci-test

Before the fix, the test fails with a BLKCNT assertion:
ERROR:../tests/qtest/xilinx-zynq-sdhci-test.c:90:wait_for_block_count:
assertion failed (qtest_readw(qts, XILINX_ZYNQ_MMC_BA + SDHC_BLKCNT) == expected): (1 == 0)

After applying the fix, the test passes:
ok 1 /arm/xilinx-zynq-sdhci/sdma/read-boundary-continue

 tests/qtest/meson.build              |   1 +
 tests/qtest/xilinx-zynq-sdhci-test.c | 178 +++++++++++++++++++++++++++
 2 files changed, 179 insertions(+)
 create mode 100644 tests/qtest/xilinx-zynq-sdhci-test.c
tests/qtest/meson.build +1 -0
index 2ae720156f..c12a35721d 100644
@@ -244,6 +244,7 @@ qtests_arm = \
    config_all_devices.has_key('CONFIG_MUSICPAL') ? ['pflash-cfi02-test'] : []) + \
   (config_all_devices.has_key('CONFIG_ASPEED_SOC') ? qtests_aspeed : []) + \
   (config_all_devices.has_key('CONFIG_NPCM7XX') ? qtests_npcm7xx : []) + \
+  (config_all_devices.has_key('CONFIG_ZYNQ') ? ['xilinx-zynq-sdhci-test'] : []) + \
   (config_all_devices.has_key('CONFIG_GENERIC_LOADER') ? ['hexloader-test'] : []) + \
   (config_all_devices.has_key('CONFIG_TPM_TIS_I2C') ? ['tpm-tis-i2c-test', 'tpm-tis-i2c-swtpm-test'] : []) + \
   (config_all_devices.has_key('CONFIG_VEXPRESS') ? ['test-arm-mptimer'] : []) + \
tests/qtest/xilinx-zynq-sdhci-test.c new file +178 -0

178 lines not on this page · raw message

Signature · 1 line
2.43.0
#5 lore raw

Re: [PATCH v7 2/2] qtest: add xilinx-zynq SDHCI sdma test

Hi Tao,

Quoted 43 lines · Tao Ding

Add a standalone qtest for the SDHCI controller on the xilinx-zynq-a9 machine.

The test covers the SDMA boundary continuation case for a multi-block read. After the controller stops at a boundary, software updates SYSAD to continue the transfer. This verifies the generic SDHCI behavior that previously failed when the continuation SYSAD write was ignored and the transfer stalled.

---
Build:

   mkdir build
   cd build
   ../configure --target-list="arm-softmmu"  --disable-slirp --enable-debug --disable-werror
   make -j4

Run:

   QTEST_QEMU_BINARY=./qemu-system-arm \
   tests/qtest/xilinx-zynq-sdhci-test

Before the fix, the test fails with a BLKCNT assertion:

   ERROR:../tests/qtest/xilinx-zynq-sdhci-test.c:90:wait_for_block_count:
   assertion failed (qtest_readw(qts, XILINX_ZYNQ_MMC_BA + SDHC_BLKCNT) == expected): (1 == 0)

After applying the fix, the test passes:
ok 1 /arm/xilinx-zynq-sdhci/sdma/read-boundary-continue

  tests/qtest/meson.build              |   1 +
  tests/qtest/xilinx-zynq-sdhci-test.c | 178 +++++++++++++++++++++++++++
  2 files changed, 179 insertions(+)

create mode 100644 tests/qtest/xilinx-zynq-sdhci-test.c

(quoted diff) +8 -0
+static void write_pattern_to_image(size_t offset, size_t len)
+{
+    int fd;
+    int ret;
+    uint8_t *buf = g_malloc(len);
+
+    for (size_t i = 0; i < len; i++) {
+        buf[i] = (i * 13 + 7) & 0xff;

Review

Quoted 10 lines
(quoted diff) +10 -0
+    }
+
+    fd = open(sd_path, O_WRONLY);
+    g_assert_cmpint(fd, >=, 0);
+    ret = pwrite(fd, buf, len, offset);
+    close(fd);
+    g_assert_cmpint(ret, ==, len);
+
+    g_free(buf);
+}

pwrite() is POSIX and is not supported on Windows:

../tests/qtest/xilinx-zynq-sdhci-test.c:71:11: error: call to undeclared function 'pwrite'; ISO C99 and later do not support implicit function declarations [-Wimplicit-function-declaration]
71 | ret = pwrite(fd, buf, len, offset);
| ^

I converted this method to GLib which is much cross-OS:

-- >8 --

tests/qtest/xilinx-zynq-sdhci-test.c +15 -8
index 601b9140834..7957358cf5d 100644
@@ -58,19 +58,26 @@ static QTestState *setup_sd_card(void)
 
 static void write_pattern_to_image(size_t offset, size_t len)
 {
-    int fd;
-    int ret;
-    uint8_t *buf = g_malloc(len);
+    gchar *buf = g_malloc(len);
+    GError *err = NULL;
+    gsize bytes_written;
+    GIOChannel *chan;
 
     for (size_t i = 0; i < len; i++) {
         buf[i] = (i * 13 + 7) & 0xff;
     }
 
-    fd = open(sd_path, O_WRONLY);
-    g_assert_cmpint(fd, >=, 0);
-    ret = pwrite(fd, buf, len, offset);
-    close(fd);
-    g_assert_cmpint(ret, ==, len);
+    chan = g_io_channel_new_file(sd_path, "w", &err);
+    g_assert_no_error(err);
+    g_io_channel_set_encoding(chan, NULL, &err);
+    g_assert_no_error(err);
+    g_io_channel_seek_position(chan, offset, G_SEEK_SET, &err);
+    g_assert_no_error(err);
+    g_io_channel_write_chars(chan, buf, len, &bytes_written, &err);
+    g_assert_no_error(err);
+    g_assert_cmpint(bytes_written, ==, len);
+    g_io_channel_shutdown(chan, TRUE, &err);
+    g_assert_no_error(err);
 
     g_free(buf);
 }

---

Regards,

Phil.

#6 lore raw
In reply to Tao Ding

Hi Philippe,

Quoted 28 lines · Tao Ding

Hi all,

This series fixes an SDMA multi-block transfer bug in the generic SDHCI controller.

The previous series was posted here:
https://lore.kernel.org/qemu-devel/[email protected]/

Thanks

Changes in v6->v7:
* patch 1/2. The addition of pre_load and post_load methods to handling of migration from older versions.
* patch 2/2 is unchanged. keep Reviewed-by Bin Meng.

Tao Ding (2):
hw/sd: sdhci: Fix SDMA boundary bug
qtest: add xilinx-zynq SDHCI sdma test

 hw/sd/sdhci.c                        |  54 +++++++-
 include/hw/sd/sdhci.h                |   2 +
 tests/qtest/meson.build              |   1 +
 tests/qtest/xilinx-zynq-sdhci-test.c | 178 +++++++++++++++++++++++++++
 4 files changed, 234 insertions(+), 1 deletion(-)
 create mode 100644 tests/qtest/xilinx-zynq-sdhci-test.c
Quoted 2 lines

base-commit: 608ad9307d5b4797d2254ee3a4bad2bc8c8bcbae --

To make things easier, would you apply this series to your local tree? Some patches in the ML are depending on this series.

Regards,
Bin

#7 lore raw
Quoted 15 lines · Bin Meng

Hi Philippe,

Quoted 12 lines

Tao Ding (2):
hw/sd: sdhci: Fix SDMA boundary bug
qtest: add xilinx-zynq SDHCI sdma test

  hw/sd/sdhci.c                        |  54 +++++++-
  include/hw/sd/sdhci.h                |   2 +
  tests/qtest/meson.build              |   1 +
  tests/qtest/xilinx-zynq-sdhci-test.c | 178 +++++++++++++++++++++++++++
  4 files changed, 234 insertions(+), 1 deletion(-)

create mode 100644 tests/qtest/xilinx-zynq-sdhci-test.c

Quoted 5 lines
Quoted 2 lines

base-commit: 608ad9307d5b4797d2254ee3a4bad2bc8c8bcbae --

To make things easier, would you apply this series to your local tree? Some patches in the ML are depending on this series.

Trying to catch up, I apologize :/ Now queued!