arm: dra7xx: Update bootloader partition size
PATCH 1/1 arm: dra7xx: Update bootloader partition size
The current size of U-Boot is already ~840 KiB.
This patch is to increase bootloader partition size up to 1 MiB and thereby fix flashing error.
Also fix U-Boot environment address on eMMC ("reserved" partition), as it's being shifted by above change.
--- include/configs/dra7xx_evm.h | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)
include/configs/dra7xx_evm.h +4 -3
@@ -13,6 +13,7 @@#define __CONFIG_DRA7XX_EVM_H#include <environment/ti/dfu.h> +#include <linux/sizes.h> #define CONFIG_DRA7XX
@@ -28,8 +29,8 @@/* MMC ENV related defines */ #define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ -#define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_SIZE SZ_128K +#define CONFIG_ENV_OFFSET 0x1A0000/* "reserved" part. */ #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)#define CONFIG_SYS_REDUNDAND_ENVIRONMENT #endif
@@ -56,7 +57,7 @@"partitions_android=" \"uuid_disk=${uuid_gpt_disk};" \"name=xloader,start=128K,size=256K,uuid=${uuid_gpt_xloader};" \ -"name=bootloader,size=768K,uuid=${uuid_gpt_bootloader};" \ +"name=bootloader,size=1M,uuid=${uuid_gpt_bootloader};" \"name=environment,size=128K,uuid=${uuid_gpt_environment};" \"name=misc,size=128K,uuid=${uuid_gpt_misc};" \"name=reserved,size=256K,uuid=${uuid_gpt_reserved};" \
Signature · 1 line
2.11.0
Bajjuri
PATCH 1/1 arm: dra7xx: Update bootloader partition size
Quoted 9 lines · Sam Protsenko
The current size of U-Boot is already ~840 KiB.
This patch is to increase bootloader partition size up to 1 MiB and thereby fix flashing error.
Also fix U-Boot environment address on eMMC ("reserved" partition), as it's being shifted by above change.
Signed-off-by Sam Protsenko <[email protected]>
Verified
Quoted 36 lines
--- include/configs/dra7xx_evm.h | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)include/configs/dra7xx_evm.h +4
-3@@ -13,6 +13,7 @@#define __CONFIG_DRA7XX_EVM_H#include <environment/ti/dfu.h> +#include <linux/sizes.h> #define CONFIG_DRA7XX @@ -28,8 +29,8 @@/* MMC ENV related defines */ #define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ -#define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_SIZE SZ_128K +#define CONFIG_ENV_OFFSET 0x1A0000/* "reserved" part. */ #define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)#define CONFIG_SYS_REDUNDAND_ENVIRONMENT #endif @@ -56,7 +57,7 @@"partitions_android=" \"uuid_disk=${uuid_gpt_disk};" \"name=xloader,start=128K,size=256K,uuid=${uuid_gpt_xloader};" \ -"name=bootloader,size=768K,uuid=${uuid_gpt_bootloader};" \ +"name=bootloader,size=1M,uuid=${uuid_gpt_bootloader};" \"name=environment,size=128K,uuid=${uuid_gpt_environment};" \"name=misc,size=128K,uuid=${uuid_gpt_misc};" \"name=reserved,size=256K,uuid=${uuid_gpt_reserved};" \
PATCH 1/1 arm: dra7xx: Update bootloader partition size
In reply to Sam Protsenko+ jj
Quoted 26 lines · Sam Protsenko
The current size of U-Boot is already ~840 KiB.
This patch is to increase bootloader partition size up to 1 MiB and thereby fix flashing error.
Also fix U-Boot environment address on eMMC ("reserved" partition), as it's being shifted by above change.
Signed-off-by Sam Protsenko <[email protected]>--- include/configs/dra7xx_evm.h | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)include/configs/dra7xx_evm.h +1
-0@@ -13,6 +13,7 @@#define __CONFIG_DRA7XX_EVM_H#include <environment/ti/dfu.h> +#include <linux/sizes.h> #define CONFIG_DRA7XX
include/configs/dra7xx_evm.h line 33
Quoted 7 lines
include/configs/dra7xx_evm.h +2
-2@@ -28,8 +29,8 @@/* MMC ENV related defines */ #define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ -#define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_SIZE SZ_128K +#define CONFIG_ENV_OFFSET 0x1A0000/* "reserved" part. */
There might be lot of side effects with this. Is it verified that this is not overlapping with any other section? Also dfu parameters needs to be updated.
Thanks and regards,
Lokesh
PATCH 1/1 arm: dra7xx: Update bootloader partition size
Quoted 28 lines · Lokesh Vutla
+ jj
Quoted 25 lines · Sam Protsenko
The current size of U-Boot is already ~840 KiB.
This patch is to increase bootloader partition size up to 1 MiB and thereby fix flashing error.
Also fix U-Boot environment address on eMMC ("reserved" partition), as it's being shifted by above change.
Signed-off-by Sam Protsenko <[email protected]>--- include/configs/dra7xx_evm.h | 7 ++++--- 1 file changed, 4 insertions(+), 3 deletions(-)include/configs/dra7xx_evm.h +1
-0@@ -13,6 +13,7 @@#define __CONFIG_DRA7XX_EVM_H#include <environment/ti/dfu.h> +#include <linux/sizes.h> #define CONFIG_DRA7XX
Quoted 11 lines
include/configs/dra7xx_evm.h line 33
Quoted 8 lines
include/configs/dra7xx_evm.h +2
-2@@ -28,8 +29,8 @@/* MMC ENV related defines */ #define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ -#define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_SIZE SZ_128K +#define CONFIG_ENV_OFFSET 0x1A0000/* "reserved" part. */ There might be lot of side effects with this. Is it verified that this is not overlapping with any other section? Also dfu parameters needs to be updated.
It does overlap with other regions used by DFU. I have patch queued for posting that does change the layout of MMC and eMMC to give more room to u-boot, args (dtb) and fixes the overlaps. I'll post it now.
Quoted 3 lines
Thanks and regards,
Lokesh
PATCH 1/1 ARM: ti: Update layout for MMC and eMMC (env and dfu)
The problems with the current DFU layout are:
MMC: The space allocated for u-boot is too small for the latest u-boot
(>750KB). We need to increase it. eMMC uses a much bigger area (2MB).
eMMC: region "u-boot.img.raw" overlaps the environment area and the region
"spl-os-image.raw".
both: region "spl-os-image.raw" is quite small and can't handle android
kernels
Fixing this requires growing some regions and moving others. Care has been taken to leave some room for further growth of "spl-os-args.raw".
Also the "env" now appears in the dfu so that it's apparent that the region is not free space that can be used to grow "u-boot.img.raw". The total space allocated for those raw binaries is 16MB, of which 13+MB are reserved for the kernel image.
---
Sam,
This patch goes a bit further in changing the layout of the MMC than yours. However it doesn't update the GPT partitioning. This would still be needed.
tested on DRA7. DFU updates ok for MMC and eMMC
Jean-Jacques
include/configs/dra7xx_evm.h | 2 +- include/configs/omap5_uevm.h | 2 +- include/configs/ti_armv7_common.h | 7 ++++--- include/environment/ti/dfu.h | 14 ++++++++------ 4 files changed, 14 insertions(+), 11 deletions(-)
include/configs/dra7xx_evm.h +1 -1
@@ -28,7 +28,7 @@#define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ #define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_OFFSET 0x220000#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)#define CONFIG_SYS_REDUNDAND_ENVIRONMENT #endif
include/configs/omap5_uevm.h +1 -1
@@ -38,7 +38,7 @@#define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ #define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_OFFSET 0x220000#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)#define CONFIG_SYS_REDUNDAND_ENVIRONMENT
include/configs/ti_armv7_common.h +4 -3
@@ -282,9 +282,10 @@#define CONFIG_SPL_FS_LOAD_ARGS_NAME "args"/* RAW SD card / eMMC */ -#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900/* address 0x120000 */ -#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80/* address 0x10000 */ -#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80/* 64KiB */ +#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1500/* address 0x2A0000 */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x1300/* address 0x260000 */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x100/* 128KiB */ +/* spl export command */ #define CONFIG_CMD_SPL
include/environment/ti/dfu.h +8 -6
@@ -12,9 +12,10 @@"rootfs part 0 2;" \"MLO fat 0 1;" \"MLO.raw raw 0x100 0x100;" \ -"u-boot.img.raw raw 0x300 0x400;" \ -"spl-os-args.raw raw 0x80 0x80;" \ -"spl-os-image.raw raw 0x900 0x2000;" \ +"u-boot.img.raw raw 0x300 0xE00;" \ +"u-env.raw raw 0x1100 0x200;" \ +"spl-os-args.raw raw 0x1300 0x100;" \ +"spl-os-image.raw raw 0x1500 0x6B00;" \"spl-os-args fat 0 1;" \"spl-os-image fat 0 1;" \"u-boot.img fat 0 1;" \
@@ -27,9 +28,10 @@"rootfs part 1 2;" \"MLO fat 1 1;" \"MLO.raw raw 0x100 0x100;" \ -"u-boot.img.raw raw 0x300 0x1000;" \ -"spl-os-args.raw raw 0x80 0x80;" \ -"spl-os-image.raw raw 0x900 0x2000;" \ +"u-boot.img.raw raw 0x300 0xE00;" \ +"u-env.raw raw 0x1100 0x200;" \ +"spl-os-args.raw raw 0x1300 0x100;" \ +"spl-os-image.raw raw 0x1500 0x6B00;" \"spl-os-args fat 1 1;" \"spl-os-image fat 1 1;" \"u-boot.img fat 1 1;" \
Signature · 1 line
1.9.1
PATCH 1/1 ARM: ti: Update layout for MMC and eMMC (env and dfu)
Quoted 16 lines · Jean-Jacques Hiblot
The problems with the current DFU layout are:
MMC: The space allocated for u-boot is too small for the latest u-boot
(>750KB). We need to increase it. eMMC uses a much bigger area (2MB).
eMMC: region "u-boot.img.raw" overlaps the environment area and the region"spl-os-image.raw".both: region "spl-os-image.raw" is quite small and can't handle android
kernelsFixing this requires growing some regions and moving others. Care has been taken to leave some room for further growth of "spl-os-args.raw".
Also the "env" now appears in the dfu so that it's apparent that the region is not free space that can be used to grow "u-boot.img.raw". The total space allocated for those raw binaries is 16MB, of which 13+MB are reserved for the kernel image.
Quoted 8 lines
Signed-off-by Jean-Jacques Hiblot <[email protected]>---
Sam,
This patch goes a bit further in changing the layout of the MMC than yours. However it doesn't update the GPT partitioning. This would still be needed.
Hi Jean-Jacques,
Got a couple of questions about this change and my patch (changing eMMC partitions table), about how to make them play nice together.
1. How DFU table is connected to eMMC partition table? And why my patch was interfering with DFU table?
2. Can I change CONFIG_ENV_OFFSET? Because my changes is going to move "reserved" partition on eMMC, where U-Boot environment is stored. Or it should be in sync with DFU table somehow? If yes -- we should work together to find solution that works best for both cases.
3. What about my similar patch for AM57x EVM (see [1])? Is it fine, or it affects DFU table as well?
Thanks.
[1] https://patchwork.ozlabs.org/patch/730736/
Quoted 89 lines
tested on DRA7. DFU updates ok for MMC and eMMC
Jean-Jacques
include/configs/dra7xx_evm.h | 2 +- include/configs/omap5_uevm.h | 2 +- include/configs/ti_armv7_common.h | 7 ++++--- include/environment/ti/dfu.h | 14 ++++++++------ 4 files changed, 14 insertions(+), 11 deletions(-)include/configs/dra7xx_evm.h +1
-1@@ -28,7 +28,7 @@#define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ #define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_OFFSET 0x220000#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)#define CONFIG_SYS_REDUNDAND_ENVIRONMENT #endif include/configs/omap5_uevm.h +1
-1@@ -38,7 +38,7 @@#define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ #define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_OFFSET 0x220000#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)#define CONFIG_SYS_REDUNDAND_ENVIRONMENT include/configs/ti_armv7_common.h +4
-3@@ -282,9 +282,10 @@#define CONFIG_SPL_FS_LOAD_ARGS_NAME "args"/* RAW SD card / eMMC */ -#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900/* address 0x120000 */ -#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80/* address 0x10000 */ -#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80/* 64KiB */ +#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1500/* address 0x2A0000 */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x1300/* address 0x260000 */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x100/* 128KiB */ +/* spl export command */ #define CONFIG_CMD_SPL include/environment/ti/dfu.h +8
-7@@ -12,9 +12,10 @@"rootfs part 0 2;" \"MLO fat 0 1;" \"MLO.raw raw 0x100 0x100;" \ -"u-boot.img.raw raw 0x300 0x400;" \ -"spl-os-args.raw raw 0x80 0x80;" \ -"spl-os-image.raw raw 0x900 0x2000;" \ +"u-boot.img.raw raw 0x300 0xE00;" \ +"u-env.raw raw 0x1100 0x200;" \ +"spl-os-args.raw raw 0x1300 0x100;" \ +"spl-os-image.raw raw 0x1500 0x6B00;" \"spl-os-args fat 0 1;" \"spl-os-image fat 0 1;" \"u-boot.img fat 0 1;" \@@ -27,9 +28,10 @@"rootfs part 1 2;" \"MLO fat 1 1;" \"MLO.raw raw 0x100 0x100;" \ -"u-boot.img.raw raw 0x300 0x1000;" \ -"spl-os-args.raw raw 0x80 0x80;" \ -"spl-os-image.raw raw 0x900 0x2000;" \ +"u-boot.img.raw raw 0x300 0xE00;" \ +"u-env.raw raw 0x1100 0x200;" \ +"spl-os-args.raw raw 0x1300 0x100;" \ +"spl-os-image.raw raw 0x1500 0x6B00;" \"spl-os-args fat 1 1;" \"spl-os-image fat 1 1;" \"u-boot.img fat 1 1;" \ --1.9.1
PATCH 1/1 ARM: ti: Update layout for MMC and eMMC (env and dfu)
Quoted 25 lines · Sam Protsenko
Quoted 16 lines · Jean-Jacques Hiblot
The problems with the current DFU layout are:
MMC: The space allocated for u-boot is too small for the latest u-boot
(>750KB). We need to increase it. eMMC uses a much bigger area (2MB).
eMMC: region "u-boot.img.raw" overlaps the environment area and the region"spl-os-image.raw".both: region "spl-os-image.raw" is quite small and can't handle android
kernelsFixing this requires growing some regions and moving others. Care has been taken to leave some room for further growth of "spl-os-args.raw".
Also the "env" now appears in the dfu so that it's apparent that the region is not free space that can be used to grow "u-boot.img.raw". The total space allocated for those raw binaries is 16MB, of which 13+MB are reserved for the kernel image.Quoted 8 lines
Signed-off-by Jean-Jacques Hiblot <[email protected]>---
Sam,
This patch goes a bit further in changing the layout of the MMC than yours. However it doesn't update the GPT partitioning. This would still be needed.
Quoted 7 lines
Hi Jean-Jacques,
Got a couple of questions about this change and my patch (changing eMMC partitions table), about how to make them play nice together.
1. How DFU table is connected to eMMC partition table? And why my patch was interfering with DFU table?
AFAIK DFU is not related to GPT. I never used the GPT so I can't for sure how it fits together.
My guess is that env_mmc.c has no idea that GPT even exists and uses raw access to the eMMC. In this case CONFIG_ENV_OFFSET must be defined to point at the beginning of your env partition and must be adapted when the GPT is updated. The same goes for the DFU. Ideally GPT and DFU should use the same layout (at least for MLO, u-boot, kernel and args).
Quoted 4 lines
2. Can I change
CONFIG_ENV_OFFSET? Because my changes is going to move "reserved" partition on eMMC, where U-Boot environment is stored. Or it should be in sync with DFU table somehow? If yes -- we should work together to find solution that works best for both cases.
CONFIG_ENV_OFFSET is loosely related to DFU: we don't update the environment through DFU. However we must make sure that the area used to store the env doesn't overlap a another region (MLO, u-boot, kernel, args). The dfu doesn't define those regions, it's done with #defines like CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR. But DFU exposes them for "remote" upgrade.
Quoted 2 lines
3. What about my similar patch for AM57x EVM (see [1])? Is it fine, or it affects DFU table as well?
I guess it's OK because the env is stored in a FAT partition:CONFIG_ENV_OFFSET is not used
Quoted 94 lines
Thanks.
[1] https://patchwork.ozlabs.org/patch/730736/
Quoted 89 lines
tested on DRA7. DFU updates ok for MMC and eMMC
Jean-Jacques
include/configs/dra7xx_evm.h | 2 +- include/configs/omap5_uevm.h | 2 +- include/configs/ti_armv7_common.h | 7 ++++--- include/environment/ti/dfu.h | 14 ++++++++------ 4 files changed, 14 insertions(+), 11 deletions(-)include/configs/dra7xx_evm.h +1
-1@@ -28,7 +28,7 @@#define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ #define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_OFFSET 0x220000#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)#define CONFIG_SYS_REDUNDAND_ENVIRONMENT #endif include/configs/omap5_uevm.h +1
-1@@ -38,7 +38,7 @@#define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ #define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_OFFSET 0x220000#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)#define CONFIG_SYS_REDUNDAND_ENVIRONMENT include/configs/ti_armv7_common.h +4
-3@@ -282,9 +282,10 @@#define CONFIG_SPL_FS_LOAD_ARGS_NAME "args"/* RAW SD card / eMMC */ -#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900/* address 0x120000 */ -#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x80/* address 0x10000 */ -#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80/* 64KiB */ +#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1500/* address 0x2A0000 */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR 0x1300/* address 0x260000 */ +#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x100/* 128KiB */ +/* spl export command */ #define CONFIG_CMD_SPL include/environment/ti/dfu.h +8
-7@@ -12,9 +12,10 @@"rootfs part 0 2;" \"MLO fat 0 1;" \"MLO.raw raw 0x100 0x100;" \ -"u-boot.img.raw raw 0x300 0x400;" \ -"spl-os-args.raw raw 0x80 0x80;" \ -"spl-os-image.raw raw 0x900 0x2000;" \ +"u-boot.img.raw raw 0x300 0xE00;" \ +"u-env.raw raw 0x1100 0x200;" \ +"spl-os-args.raw raw 0x1300 0x100;" \ +"spl-os-image.raw raw 0x1500 0x6B00;" \"spl-os-args fat 0 1;" \"spl-os-image fat 0 1;" \"u-boot.img fat 0 1;" \@@ -27,9 +28,10 @@"rootfs part 1 2;" \"MLO fat 1 1;" \"MLO.raw raw 0x100 0x100;" \ -"u-boot.img.raw raw 0x300 0x1000;" \ -"spl-os-args.raw raw 0x80 0x80;" \ -"spl-os-image.raw raw 0x900 0x2000;" \ +"u-boot.img.raw raw 0x300 0xE00;" \ +"u-env.raw raw 0x1100 0x200;" \ +"spl-os-args.raw raw 0x1300 0x100;" \ +"spl-os-image.raw raw 0x1500 0x6B00;" \"spl-os-args fat 1 1;" \"spl-os-image fat 1 1;" \"u-boot.img fat 1 1;" \ --1.9.1
PATCH 1/1 ARM: ti: Update layout for MMC and eMMC (env and dfu)
Quoted 55 lines · Jean-Jacques Hiblot
Quoted 31 lines · Sam Protsenko
Quoted 19 lines · Jean-Jacques Hiblot
The problems with the current DFU layout are:
MMC: The space allocated for u-boot is too small for the latest u-boot
(>750KB). We need to increase it. eMMC uses a much bigger area
(2MB).
eMMC: region "u-boot.img.raw" overlaps the environment area and the region"spl-os-image.raw".both: region "spl-os-image.raw" is quite small and can't handle android
kernelsFixing this requires growing some regions and moving others. Care has been taken to leave some room for further growth of "spl-os-args.raw".
Also the "env" now appears in the dfu so that it's apparent that the region is not free space that can be used to grow "u-boot.img.raw". The total space allocated for those raw binaries is 16MB, of which 13+MB are reserved for the kernel image.Quoted 9 lines
Signed-off-by Jean-Jacques Hiblot <[email protected]>---
Sam,
This patch goes a bit further in changing the layout of the MMC than yours. However
it doesn't update the GPT partitioning. This would still be needed.Quoted 7 lines
Hi Jean-Jacques,
Got a couple of questions about this change and my patch (changing eMMC partitions table), about how to make them play nice together.
1. How DFU table is connected to eMMC partition table? And why my patch was interfering with DFU table?
AFAIK DFU is not related to GPT. I never used the GPT so I can't for sure how it fits together.
My guess is thatenv_mmc.chas no idea that GPT even exists and uses raw access to the eMMC. In this caseCONFIG_ENV_OFFSETmust be defined to point at the beginning of your env partition and must be adapted when the GPT is updated. The same goes for the DFU. Ideally GPT and DFU should use the same layout (at least for MLO, u-boot, kernel and args).Quoted 4 lines
2. Can I change
CONFIG_ENV_OFFSET? Because my changes is going to move "reserved" partition on eMMC, where U-Boot environment is stored. Or it should be in sync with DFU table somehow? If yes -- we should work together to find solution that works best for both cases.
Quoted 7 lines
CONFIG_ENV_OFFSETis loosely related to DFU: we don't update the environment through DFU. However we must make sure that the area used to store the env doesn't overlap a another region (MLO, u-boot, kernel, args). The dfu doesn't define those regions, it's done with #defines likeCONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR. But DFU exposes them for "remote" upgrade.
So if I change eMMC GPT partition table, it's ok for me to update CONFIG_ENV_OFFSET as well, right? Because in my case CONFIG_ENV_OFFSET is going to be different from the value your patch sets. In case of eMMC table, we're using "reserved" partition to store U-Boot environment, and I want it to be at 1664 KiB, which gives us CONFIG_ENV_OFFSET=0x1A0000. Is it ok if I change it to that value? Or something else must be changed along with it? If yes, then what exactly?
Thanks.
Quoted 109 lines
Quoted 2 lines
3. What about my similar patch for AM57x EVM (see [1])? Is it fine, or it affects DFU table as well?
I guess it's OK because the env is stored in a FAT partition:
CONFIG_ENV_OFFSETis not usedQuoted 101 lines
Thanks.
[1] https://patchwork.ozlabs.org/patch/730736/
Quoted 96 lines
tested on DRA7. DFU updates ok for MMC and eMMC
Jean-Jacques
include/configs/dra7xx_evm.h | 2 +- include/configs/omap5_uevm.h | 2 +- include/configs/ti_armv7_common.h | 7 ++++--- include/environment/ti/dfu.h | 14 ++++++++------ 4 files changed, 14 insertions(+), 11 deletions(-)include/configs/dra7xx_evm.h +1
-1@@ -28,7 +28,7 @@#define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ #define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_OFFSET 0x220000#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)#define CONFIG_SYS_REDUNDAND_ENVIRONMENT #endifinclude/configs/omap5_uevm.h +1
-1@@ -38,7 +38,7 @@#define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ #define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_OFFSET 0x220000#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)#define CONFIG_SYS_REDUNDAND_ENVIRONMENT include/configs/ti_armv7_common.h +0
-1@@ -282,9 +282,10 @@#define CONFIG_SPL_FS_LOAD_ARGS_NAME "args"/* RAW SD card / eMMC */ -#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900/* address
0x120000*/
-#defineCONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR0x80/* address0x10000*/include/configs/ti_armv7_common.h +1
-1-#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80/* 64KiB */ +#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1500/* address
0x2A0000*/
+#defineCONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR0x1300/* address0x260000*/include/configs/ti_armv7_common.h +2
-0+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x100/* 128KiB */ +/* spl export command */ #define CONFIG_CMD_SPL include/environment/ti/dfu.h +8
-7@@ -12,9 +12,10 @@"rootfs part 0 2;" \"MLO fat 0 1;" \"MLO.raw raw 0x100 0x100;" \ -"u-boot.img.raw raw 0x300 0x400;" \ -"spl-os-args.raw raw 0x80 0x80;" \ -"spl-os-image.raw raw 0x900 0x2000;" \ +"u-boot.img.raw raw 0x300 0xE00;" \ +"u-env.raw raw 0x1100 0x200;" \ +"spl-os-args.raw raw 0x1300 0x100;" \ +"spl-os-image.raw raw 0x1500 0x6B00;" \"spl-os-args fat 0 1;" \"spl-os-image fat 0 1;" \"u-boot.img fat 0 1;" \@@ -27,9 +28,10 @@"rootfs part 1 2;" \"MLO fat 1 1;" \"MLO.raw raw 0x100 0x100;" \ -"u-boot.img.raw raw 0x300 0x1000;" \ -"spl-os-args.raw raw 0x80 0x80;" \ -"spl-os-image.raw raw 0x900 0x2000;" \ +"u-boot.img.raw raw 0x300 0xE00;" \ +"u-env.raw raw 0x1100 0x200;" \ +"spl-os-args.raw raw 0x1300 0x100;" \ +"spl-os-image.raw raw 0x1500 0x6B00;" \"spl-os-args fat 1 1;" \"spl-os-image fat 1 1;" \"u-boot.img fat 1 1;" \ --1.9.1
PATCH 1/1 ARM: ti: Update layout for MMC and eMMC (env and dfu)
Quoted 58 lines · Sam Protsenko
Quoted 50 lines · Jean-Jacques Hiblot
Quoted 29 lines · Sam Protsenko
Quoted 18 lines · Jean-Jacques Hiblot
The problems with the current DFU layout are:
MMC: The space allocated for u-boot is too small for the latest u-boot
(>750KB). We need to increase it. eMMC uses a much bigger area
(2MB).
eMMC: region "u-boot.img.raw" overlaps the environment area and the region"spl-os-image.raw".both: region "spl-os-image.raw" is quite small and can't handle android
kernelsFixing this requires growing some regions and moving others. Care has been taken to leave some room for further growth of "spl-os-args.raw".
Also the "env" now appears in the dfu so that it's apparent that the region is not free space that can be used to grow "u-boot.img.raw". The total space allocated for those raw binaries is 16MB, of which 13+MB are reserved for the kernel image.Quoted 9 lines
Signed-off-by Jean-Jacques Hiblot <[email protected]>---
Sam,
This patch goes a bit further in changing the layout of the MMC than yours. However
it doesn't update the GPT partitioning. This would still be needed.Quoted 7 lines
Hi Jean-Jacques,
Got a couple of questions about this change and my patch (changing eMMC partitions table), about how to make them play nice together.
1. How DFU table is connected to eMMC partition table? And why my patch was interfering with DFU table?
AFAIK DFU is not related to GPT. I never used the GPT so I can't for sure how it fits together.
My guess is thatenv_mmc.chas no idea that GPT even exists and uses raw access to the eMMC. In this caseCONFIG_ENV_OFFSETmust be defined to point at the beginning of your env partition and must be adapted when the GPT is updated. The same goes for the DFU. Ideally GPT and DFU should use the same layout (at least for MLO, u-boot, kernel and args).Quoted 4 lines
2. Can I change
CONFIG_ENV_OFFSET? Because my changes is going to move "reserved" partition on eMMC, where U-Boot environment is stored. Or it should be in sync with DFU table somehow? If yes -- we should work together to find solution that works best for both cases.Quoted 7 lines
CONFIG_ENV_OFFSETis loosely related to DFU: we don't update the environment through DFU. However we must make sure that the area used to store the env doesn't overlap a another region (MLO, u-boot, kernel, args). The dfu doesn't define those regions, it's done with #defines likeCONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR. But DFU exposes them for "remote" upgrade.
Quoted 2 lines
So if I change eMMC GPT partition table, it's ok for me to update
CONFIG_ENV_OFFSETas well, right?
Yes you need to change it
Quoted 7 lines
Because in my case
CONFIG_ENV_OFFSET
is going to be different from the value your patch sets. In case of eMMC table, we're using "reserved" partition to store U-Boot environment, and I want it to be at 1664 KiB, which gives usCONFIG_ENV_OFFSET=0x1A0000. Is it ok if I change it to that value? Or something else must be changed along with it? If yes, then what exactly?
You need to adapt DFU if you plan to use it. Maybe you can define a new layout for DFU, something like dfu_alt_info_emmc_gpt that will reflect your GPT layout
Anyway IMO it would be good to use the same offset/size for GPT and non-GPT case for the following regions:
- MLO
- u-boot
- env
For MLO we already use the same: offset 128kB / size 256kB For u-boot, you increased the size to 1MB, I suggest that we increase it a bit more (1.5MB or 2MB) just to make sure that we don't have to increase its size again next year.
For the env, I suggest that the size is increased to 256kB to take care of redundant env.
Quoted 109 lines
Thanks.
Quoted 106 lines
Quoted 2 lines
3. What about my similar patch for AM57x EVM (see [1])? Is it fine, or it affects DFU table as well?
I guess it's OK because the env is stored in a FAT partition:
CONFIG_ENV_OFFSETis not usedQuoted 100 lines
Thanks.
[1] https://patchwork.ozlabs.org/patch/730736/
Quoted 96 lines
tested on DRA7. DFU updates ok for MMC and eMMC
Jean-Jacques
include/configs/dra7xx_evm.h | 2 +- include/configs/omap5_uevm.h | 2 +- include/configs/ti_armv7_common.h | 7 ++++--- include/environment/ti/dfu.h | 14 ++++++++------ 4 files changed, 14 insertions(+), 11 deletions(-)include/configs/dra7xx_evm.h +1
-1@@ -28,7 +28,7 @@#define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ #define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_OFFSET 0x220000#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)#define CONFIG_SYS_REDUNDAND_ENVIRONMENT #endifinclude/configs/omap5_uevm.h +1
-1@@ -38,7 +38,7 @@#define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ #define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_OFFSET 0x220000#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)#define CONFIG_SYS_REDUNDAND_ENVIRONMENT include/configs/ti_armv7_common.h +0
-1@@ -282,9 +282,10 @@#define CONFIG_SPL_FS_LOAD_ARGS_NAME "args"/* RAW SD card / eMMC */ -#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900/* address
0x120000*/
-#defineCONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR0x80/* address0x10000*/include/configs/ti_armv7_common.h +1
-1-#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80/* 64KiB */ +#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1500/* address
0x2A0000*/
+#defineCONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR0x1300/* address0x260000*/include/configs/ti_armv7_common.h +2
-0+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x100/* 128KiB */ +/* spl export command */ #define CONFIG_CMD_SPL include/environment/ti/dfu.h +8
-7@@ -12,9 +12,10 @@"rootfs part 0 2;" \"MLO fat 0 1;" \"MLO.raw raw 0x100 0x100;" \ -"u-boot.img.raw raw 0x300 0x400;" \ -"spl-os-args.raw raw 0x80 0x80;" \ -"spl-os-image.raw raw 0x900 0x2000;" \ +"u-boot.img.raw raw 0x300 0xE00;" \ +"u-env.raw raw 0x1100 0x200;" \ +"spl-os-args.raw raw 0x1300 0x100;" \ +"spl-os-image.raw raw 0x1500 0x6B00;" \"spl-os-args fat 0 1;" \"spl-os-image fat 0 1;" \"u-boot.img fat 0 1;" \@@ -27,9 +28,10 @@"rootfs part 1 2;" \"MLO fat 1 1;" \"MLO.raw raw 0x100 0x100;" \ -"u-boot.img.raw raw 0x300 0x1000;" \ -"spl-os-args.raw raw 0x80 0x80;" \ -"spl-os-image.raw raw 0x900 0x2000;" \ +"u-boot.img.raw raw 0x300 0xE00;" \ +"u-env.raw raw 0x1100 0x200;" \ +"spl-os-args.raw raw 0x1300 0x100;" \ +"spl-os-image.raw raw 0x1500 0x6B00;" \"spl-os-args fat 1 1;" \"spl-os-image fat 1 1;" \"u-boot.img fat 1 1;" \ --1.9.1
PATCH 1/1 ARM: ti: Update layout for MMC and eMMC (env and dfu)
Quoted 98 lines · Jean-Jacques Hiblot
Quoted 72 lines · Sam Protsenko
Quoted 59 lines · Jean-Jacques Hiblot
Quoted 32 lines · Sam Protsenko
Quoted 20 lines · Jean-Jacques Hiblot
The problems with the current DFU layout are:
MMC: The space allocated for u-boot is too small for the latest u-boot
(>750KB). We need to increase it. eMMC uses a much bigger area
(2MB).
eMMC: region "u-boot.img.raw" overlaps the environment area and the region"spl-os-image.raw".both: region "spl-os-image.raw" is quite small and can't handle android
kernelsFixing this requires growing some regions and moving others. Care has been taken to leave some room for further growth of "spl-os-args.raw".
Also the "env" now appears in the dfu so that it's apparent that the region is not free space that can be used to grow "u-boot.img.raw". The total space allocated for those raw binaries is 16MB, of which 13+MB
are reserved for the kernel image.Quoted 9 lines
Signed-off-by Jean-Jacques Hiblot <[email protected]>---
Sam,
This patch goes a bit further in changing the layout of the MMC than yours. However
it doesn't update the GPT partitioning. This would still be needed.Quoted 7 lines
Hi Jean-Jacques,
Got a couple of questions about this change and my patch (changing eMMC partitions table), about how to make them play nice together.
1. How DFU table is connected to eMMC partition table? And why my patch was interfering with DFU table?
AFAIK DFU is not related to GPT. I never used the GPT so I can't for sure how it fits together.
My guess is thatenv_mmc.chas no idea that GPT even exists and uses raw access to the eMMC. In this caseCONFIG_ENV_OFFSETmust be defined to point
at the beginning of your env partition and must be adapted when the GPT is
updated. The same goes for the DFU. Ideally GPT and DFU should use the same
layout (at least for MLO, u-boot, kernel and args).Quoted 4 lines
2. Can I change
CONFIG_ENV_OFFSET? Because my changes is going to move "reserved" partition on eMMC, where U-Boot environment is stored. Or it should be in sync with DFU table somehow? If yes -- we should work together to find solution that works best for both cases.Quoted 10 lines
CONFIG_ENV_OFFSETis loosely related to DFU: we don't update the environment
through DFU. However we must make sure that the area used to store the env
doesn't overlap a another region (MLO, u-boot, kernel, args). The dfu doesn't define those regions, it's done with #defines likeCONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR. But DFU exposes them for "remote"
upgrade.Quoted 2 lines
So if I change eMMC GPT partition table, it's ok for me to update
CONFIG_ENV_OFFSETas well, right?Yes you need to change it
Quoted 8 lines
Because in my case
CONFIG_ENV_OFFSET
is going to be different from the value your patch sets. In case of eMMC table, we're using "reserved" partition to store U-Boot environment, and I want it to be at 1664 KiB, which gives usCONFIG_ENV_OFFSET=0x1A0000. Is it ok if I change it to that value? Or something else must be changed along with it? If yes, then what exactly?You need to adapt DFU if you plan to use it. Maybe you can define a new layout for DFU, something like
dfu_alt_info_emmc_gptthat will reflect your GPT layoutAnyway IMO it would be good to use the same offset/size for GPT and non-GPT case for the following regions:
- MLO
- u-boot
- env
Quoted 7 lines
For MLO we already use the same: offset 128kB / size 256kB
For u-boot, you increased the size to 1MB, I suggest that we increase it a bit more (1.5MB or 2MB) just to make sure that we don't have to increase its size again next year.
For the env, I suggest that the size is increased to 256kB to take care of redundant env.
Thank you for detailed explanation. I'm gonna get back to that task in a few weeks, don't have enough time right now. Once I come up with some particular patch, I will add you to reviewers, to be sure that DFU part is correct.
Quoted 116 lines
Quoted 115 lines
Thanks.
Quoted 110 lines
Quoted 2 lines
3. What about my similar patch for AM57x EVM (see [1])? Is it fine, or it affects DFU table as well?
I guess it's OK because the env is stored in a FAT partition:
CONFIG_ENV_OFFSETis not usedQuoted 103 lines
Thanks.
[1] https://patchwork.ozlabs.org/patch/730736/
Quoted 99 lines
tested on DRA7. DFU updates ok for MMC and eMMC
Jean-Jacques
include/configs/dra7xx_evm.h | 2 +- include/configs/omap5_uevm.h | 2 +- include/configs/ti_armv7_common.h | 7 ++++--- include/environment/ti/dfu.h | 14 ++++++++------ 4 files changed, 14 insertions(+), 11 deletions(-)include/configs/dra7xx_evm.h +1
-1@@ -28,7 +28,7 @@#define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ #define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_OFFSET 0x220000#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)#define CONFIG_SYS_REDUNDAND_ENVIRONMENT #endifinclude/configs/omap5_uevm.h +1
-1@@ -38,7 +38,7 @@#define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ #define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_OFFSET 0x220000#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)#define CONFIG_SYS_REDUNDAND_ENVIRONMENT include/configs/ti_armv7_common.h +0
-1@@ -282,9 +282,10 @@#define CONFIG_SPL_FS_LOAD_ARGS_NAME "args"/* RAW SD card / eMMC */ -#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900/* address
0x120000*/
-#defineCONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR0x80/* address0x10000*/include/configs/ti_armv7_common.h +1
-1-#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80/* 64KiB */ +#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1500/* address
0x2A0000*/
+#defineCONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR0x1300/* address0x260000*/include/configs/ti_armv7_common.h +2
-0+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x100/* 128KiB */ +/* spl export command */ #define CONFIG_CMD_SPL include/environment/ti/dfu.h +8
-7@@ -12,9 +12,10 @@"rootfs part 0 2;" \"MLO fat 0 1;" \"MLO.raw raw 0x100 0x100;" \ -"u-boot.img.raw raw 0x300 0x400;" \ -"spl-os-args.raw raw 0x80 0x80;" \ -"spl-os-image.raw raw 0x900 0x2000;" \ +"u-boot.img.raw raw 0x300 0xE00;" \ +"u-env.raw raw 0x1100 0x200;" \ +"spl-os-args.raw raw 0x1300 0x100;" \ +"spl-os-image.raw raw 0x1500 0x6B00;" \"spl-os-args fat 0 1;" \"spl-os-image fat 0 1;" \"u-boot.img fat 0 1;" \@@ -27,9 +28,10 @@"rootfs part 1 2;" \"MLO fat 1 1;" \"MLO.raw raw 0x100 0x100;" \ -"u-boot.img.raw raw 0x300 0x1000;" \ -"spl-os-args.raw raw 0x80 0x80;" \ -"spl-os-image.raw raw 0x900 0x2000;" \ +"u-boot.img.raw raw 0x300 0xE00;" \ +"u-env.raw raw 0x1100 0x200;" \ +"spl-os-args.raw raw 0x1300 0x100;" \ +"spl-os-image.raw raw 0x1500 0x6B00;" \"spl-os-args fat 1 1;" \"spl-os-image fat 1 1;" \"u-boot.img fat 1 1;" \ --1.9.1
PATCH 1/1 ARM: ti: Update layout for MMC and eMMC (env and dfu)
Quoted 96 lines · Sam Protsenko
Quoted 88 lines · Jean-Jacques Hiblot
Quoted 66 lines · Sam Protsenko
Quoted 54 lines · Jean-Jacques Hiblot
Quoted 30 lines · Sam Protsenko
Quoted 19 lines · Jean-Jacques Hiblot
The problems with the current DFU layout are:
MMC: The space allocated for u-boot is too small for the latest u-boot
(>750KB). We need to increase it. eMMC uses a much bigger area
(2MB).
eMMC: region "u-boot.img.raw" overlaps the environment area and the region"spl-os-image.raw".both: region "spl-os-image.raw" is quite small and can't handle android
kernelsFixing this requires growing some regions and moving others. Care has been taken to leave some room for further growth of "spl-os-args.raw".
Also the "env" now appears in the dfu so that it's apparent that the region is not free space that can be used to grow "u-boot.img.raw". The total space allocated for those raw binaries is 16MB, of which 13+MB
are reserved for the kernel image.Quoted 9 lines
Signed-off-by Jean-Jacques Hiblot <[email protected]>---
Sam,
This patch goes a bit further in changing the layout of the MMC than yours. However
it doesn't update the GPT partitioning. This would still be needed.Quoted 7 lines
Hi Jean-Jacques,
Got a couple of questions about this change and my patch (changing eMMC partitions table), about how to make them play nice together.
1. How DFU table is connected to eMMC partition table? And why my patch was interfering with DFU table?
AFAIK DFU is not related to GPT. I never used the GPT so I can't for sure how it fits together.
My guess is thatenv_mmc.chas no idea that GPT even exists and uses raw access to the eMMC. In this caseCONFIG_ENV_OFFSETmust be defined to point
at the beginning of your env partition and must be adapted when the GPT is
updated. The same goes for the DFU. Ideally GPT and DFU should use the same
layout (at least for MLO, u-boot, kernel and args).Quoted 4 lines
2. Can I change
CONFIG_ENV_OFFSET? Because my changes is going to move "reserved" partition on eMMC, where U-Boot environment is stored. Or it should be in sync with DFU table somehow? If yes -- we should work together to find solution that works best for both cases.Quoted 10 lines
CONFIG_ENV_OFFSETis loosely related to DFU: we don't update the environment
through DFU. However we must make sure that the area used to store the env
doesn't overlap a another region (MLO, u-boot, kernel, args). The dfu doesn't define those regions, it's done with #defines likeCONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR. But DFU exposes them for "remote"
upgrade.Quoted 2 lines
So if I change eMMC GPT partition table, it's ok for me to update
CONFIG_ENV_OFFSETas well, right?Yes you need to change it
Quoted 7 lines
Because in my case
CONFIG_ENV_OFFSET
is going to be different from the value your patch sets. In case of eMMC table, we're using "reserved" partition to store U-Boot environment, and I want it to be at 1664 KiB, which gives usCONFIG_ENV_OFFSET=0x1A0000. Is it ok if I change it to that value? Or something else must be changed along with it? If yes, then what exactly?You need to adapt DFU if you plan to use it. Maybe you can define a new layout for DFU, something like
dfu_alt_info_emmc_gptthat will reflect your GPT layoutAnyway IMO it would be good to use the same offset/size for GPT and non-GPT case for the following regions:
- MLO
- u-boot
- envQuoted 7 lines
For MLO we already use the same: offset 128kB / size 256kB
For u-boot, you increased the size to 1MB, I suggest that we increase it a bit more (1.5MB or 2MB) just to make sure that we don't have to increase its size again next year.
For the env, I suggest that the size is increased to 256kB to take care of redundant env.
Quoted 4 lines
Thank you for detailed explanation. I'm gonna get back to that task in a few weeks, don't have enough time right now. Once I come up with some particular patch, I will add you to reviewers, to be sure that DFU part is correct.
Before you switch to another task maybe we can agree on the offset and sizes for MLO, u-boot and env so that I can do the necessary changes on my side (dfu, #defines).
Quoted 113 lines
Quoted 113 lines
Quoted 113 lines
Thanks.
Quoted 109 lines
Quoted 2 lines
3. What about my similar patch for AM57x EVM (see [1])? Is it fine, or it affects DFU table as well?
I guess it's OK because the env is stored in a FAT partition:
CONFIG_ENV_OFFSETis not usedQuoted 103 lines
Thanks.
[1] https://patchwork.ozlabs.org/patch/730736/
Quoted 99 lines
tested on DRA7. DFU updates ok for MMC and eMMC
Jean-Jacques
include/configs/dra7xx_evm.h | 2 +- include/configs/omap5_uevm.h | 2 +- include/configs/ti_armv7_common.h | 7 ++++--- include/environment/ti/dfu.h | 14 ++++++++------ 4 files changed, 14 insertions(+), 11 deletions(-)include/configs/dra7xx_evm.h +1
-1@@ -28,7 +28,7 @@#define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ #define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_OFFSET 0x220000#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)#define CONFIG_SYS_REDUNDAND_ENVIRONMENT #endifinclude/configs/omap5_uevm.h +1
-1@@ -38,7 +38,7 @@#define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ #define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_OFFSET 0x220000#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)#define CONFIG_SYS_REDUNDAND_ENVIRONMENT include/configs/ti_armv7_common.h +0
-1@@ -282,9 +282,10 @@#define CONFIG_SPL_FS_LOAD_ARGS_NAME "args"/* RAW SD card / eMMC */ -#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900/* address
0x120000*/
-#defineCONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR0x80/* address0x10000*/include/configs/ti_armv7_common.h +1
-1-#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80/* 64KiB */ +#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1500/* address
0x2A0000*/
+#defineCONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR0x1300/* address0x260000*/include/configs/ti_armv7_common.h +2
-0+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x100/* 128KiB */ +/* spl export command */ #define CONFIG_CMD_SPL include/environment/ti/dfu.h +8
-7@@ -12,9 +12,10 @@"rootfs part 0 2;" \"MLO fat 0 1;" \"MLO.raw raw 0x100 0x100;" \ -"u-boot.img.raw raw 0x300 0x400;" \ -"spl-os-args.raw raw 0x80 0x80;" \ -"spl-os-image.raw raw 0x900 0x2000;" \ +"u-boot.img.raw raw 0x300 0xE00;" \ +"u-env.raw raw 0x1100 0x200;" \ +"spl-os-args.raw raw 0x1300 0x100;" \ +"spl-os-image.raw raw 0x1500 0x6B00;" \"spl-os-args fat 0 1;" \"spl-os-image fat 0 1;" \"u-boot.img fat 0 1;" \@@ -27,9 +28,10 @@"rootfs part 1 2;" \"MLO fat 1 1;" \"MLO.raw raw 0x100 0x100;" \ -"u-boot.img.raw raw 0x300 0x1000;" \ -"spl-os-args.raw raw 0x80 0x80;" \ -"spl-os-image.raw raw 0x900 0x2000;" \ +"u-boot.img.raw raw 0x300 0xE00;" \ +"u-env.raw raw 0x1100 0x200;" \ +"spl-os-args.raw raw 0x1300 0x100;" \ +"spl-os-image.raw raw 0x1500 0x6B00;" \"spl-os-args fat 1 1;" \"spl-os-image fat 1 1;" \"u-boot.img fat 1 1;" \ --1.9.1
PATCH 1/1 ARM: ti: Update layout for MMC and eMMC (env and dfu)
Quoted 122 lines · Jean-Jacques Hiblot
Quoted 119 lines · Sam Protsenko
Quoted 116 lines · Jean-Jacques Hiblot
Quoted 78 lines · Sam Protsenko
Quoted 65 lines · Jean-Jacques Hiblot
Quoted 36 lines · Sam Protsenko
Quoted 23 lines · Jean-Jacques Hiblot
The problems with the current DFU layout are:
MMC: The space allocated for u-boot is too small for the latest u-boot
(>750KB). We need to increase it. eMMC uses a much bigger
area
(2MB).
eMMC: region "u-boot.img.raw" overlaps the environment area and the region"spl-os-image.raw".both: region "spl-os-image.raw" is quite small and can't handle android
kernelsFixing this requires growing some regions and moving others. Care has been taken to leave some room for further growth of "spl-os-args.raw".
Also the "env" now appears in the dfu so that it's apparent that the region is not free space that can be used to grow "u-boot.img.raw". The total space allocated for those raw binaries is 16MB, of which 13+MB
are reserved for the kernel image.Quoted 9 lines
Signed-off-by Jean-Jacques Hiblot <[email protected]>---
Sam,
This patch goes a bit further in changing the layout of the MMC than yours. However
it doesn't update the GPT partitioning. This would still be needed.Quoted 7 lines
Hi Jean-Jacques,
Got a couple of questions about this change and my patch (changing eMMC partitions table), about how to make them play nice together.
1. How DFU table is connected to eMMC partition table? And why my patch was interfering with DFU table?
AFAIK DFU is not related to GPT. I never used the GPT so I can't for sure
how it fits together.
My guess is thatenv_mmc.chas no idea that GPT even exists and uses raw
access to the eMMC. In this caseCONFIG_ENV_OFFSETmust be defined to point
at the beginning of your env partition and must be adapted when the GPT is
updated. The same goes for the DFU. Ideally GPT and DFU should use the same
layout (at least for MLO, u-boot, kernel and args).Quoted 4 lines
2. Can I change
CONFIG_ENV_OFFSET? Because my changes is going to move "reserved" partition on eMMC, where U-Boot environment is stored. Or it should be in sync with DFU table somehow? If yes -- we should work together to find solution that works best for both cases.Quoted 10 lines
CONFIG_ENV_OFFSETis loosely related to DFU: we don't update the environment
through DFU. However we must make sure that the area used to store the env
doesn't overlap a another region (MLO, u-boot, kernel, args). The dfu doesn't define those regions, it's done with #defines likeCONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR. But DFU exposes them for "remote"
upgrade.Quoted 2 lines
So if I change eMMC GPT partition table, it's ok for me to update
CONFIG_ENV_OFFSETas well, right?Yes you need to change it
Quoted 8 lines
Because in my case
CONFIG_ENV_OFFSET
is going to be different from the value your patch sets. In case of eMMC table, we're using "reserved" partition to store U-Boot environment, and I want it to be at 1664 KiB, which gives usCONFIG_ENV_OFFSET=0x1A0000. Is it ok if I change it to that value? Or something else must be changed along with it? If yes, then what exactly?You need to adapt DFU if you plan to use it. Maybe you can define a new layout for DFU, something like
dfu_alt_info_emmc_gptthat will reflect your
GPT layoutAnyway IMO it would be good to use the same offset/size for GPT and non-GPT
case for the following regions:
- MLO
- u-boot
- envFor MLO we already use the same: offset 128kB / size 256kB For u-boot, you increased the size to 1MB, I suggest that we increase it a
bit more (1.5MB or 2MB) just to make sure that we don't have to increase its
size again next year.
For the env, I suggest that the size is increased to 256kB to take care of
redundant env.
Quoted 9 lines
Quoted 4 lines
Thank you for detailed explanation. I'm gonna get back to that task in a few weeks, don't have enough time right now. Once I come up with some particular patch, I will add you to reviewers, to be sure that DFU part is correct.
Before you switch to another task maybe we can agree on the offset and sizes for MLO, u-boot and env so that I can do the necessary changes on my side (dfu, #defines).
Sure. I agree with you that we should increase U-Boot partition. I'm gonna do next layout for eMMC table:
MLO: start=128K, size=256K
U-Boot: size=2M
DTB: size=128K
misc: size=128K
U-Boot environment: size=256K
efs: size=16M
crypto: size=16K
recovery: size=10M
boot: size=10M
system: size=768M
cache: size=256M
ipu1: size=1M
ipu2: size=1M
userdata: size=the rest of eMMC spaceIs it ok with you? Also, we should check if it's ok with Praneeth, as he mentioned that some changes to that table may be necessary in the future (from Android side).
Quoted 118 lines
Quoted 117 lines
Quoted 117 lines
Quoted 117 lines
Thanks.
Quoted 112 lines
Quoted 2 lines
3. What about my similar patch for AM57x EVM (see [1])? Is it fine, or it affects DFU table as well?
I guess it's OK because the env is stored in a FAT partition:
CONFIG_ENV_OFFSETis not usedQuoted 105 lines
Thanks.
[1] https://patchwork.ozlabs.org/patch/730736/
Quoted 101 lines
tested on DRA7. DFU updates ok for MMC and eMMC
Jean-Jacques
include/configs/dra7xx_evm.h | 2 +- include/configs/omap5_uevm.h | 2 +- include/configs/ti_armv7_common.h | 7 ++++--- include/environment/ti/dfu.h | 14 ++++++++------ 4 files changed, 14 insertions(+), 11 deletions(-)include/configs/dra7xx_evm.h +1
-1@@ -28,7 +28,7 @@#define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ #define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_OFFSET 0x220000#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)#define CONFIG_SYS_REDUNDAND_ENVIRONMENT #endifinclude/configs/omap5_uevm.h +1
-1@@ -38,7 +38,7 @@#define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ #define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_OFFSET 0x220000#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)#define CONFIG_SYS_REDUNDAND_ENVIRONMENTinclude/configs/ti_armv7_common.h +0
-1@@ -282,9 +282,10 @@#define CONFIG_SPL_FS_LOAD_ARGS_NAME "args"/* RAW SD card / eMMC */ -#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900/* address
0x120000*/
-#defineCONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR0x80/* address0x10000*/include/configs/ti_armv7_common.h +1
-1-#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80/* 64KiB */ +#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1500/* address
0x2A0000*/
+#defineCONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR0x1300/* address0x260000*/include/configs/ti_armv7_common.h +2
-0+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x100/* 128KiB */ +/* spl export command */ #define CONFIG_CMD_SPL include/environment/ti/dfu.h +8
-7@@ -12,9 +12,10 @@"rootfs part 0 2;" \"MLO fat 0 1;" \"MLO.raw raw 0x100 0x100;" \ -"u-boot.img.raw raw 0x300 0x400;" \ -"spl-os-args.raw raw 0x80 0x80;" \ -"spl-os-image.raw raw 0x900 0x2000;" \ +"u-boot.img.raw raw 0x300 0xE00;" \ +"u-env.raw raw 0x1100 0x200;" \ +"spl-os-args.raw raw 0x1300 0x100;" \ +"spl-os-image.raw raw 0x1500 0x6B00;" \"spl-os-args fat 0 1;" \"spl-os-image fat 0 1;" \"u-boot.img fat 0 1;" \@@ -27,9 +28,10 @@"rootfs part 1 2;" \"MLO fat 1 1;" \"MLO.raw raw 0x100 0x100;" \ -"u-boot.img.raw raw 0x300 0x1000;" \ -"spl-os-args.raw raw 0x80 0x80;" \ -"spl-os-image.raw raw 0x900 0x2000;" \ +"u-boot.img.raw raw 0x300 0xE00;" \ +"u-env.raw raw 0x1100 0x200;" \ +"spl-os-args.raw raw 0x1300 0x100;" \ +"spl-os-image.raw raw 0x1500 0x6B00;" \"spl-os-args fat 1 1;" \"spl-os-image fat 1 1;" \"u-boot.img fat 1 1;" \ --1.9.1
PATCH 1/1 ARM: ti: Update layout for MMC and eMMC (env and dfu)
Quoted 119 lines · Sam Protsenko
Quoted 110 lines · Jean-Jacques Hiblot
Quoted 108 lines · Sam Protsenko
Quoted 106 lines · Jean-Jacques Hiblot
Quoted 72 lines · Sam Protsenko
Quoted 60 lines · Jean-Jacques Hiblot
Quoted 34 lines · Sam Protsenko
Quoted 22 lines · Jean-Jacques Hiblot
The problems with the current DFU layout are:
MMC: The space allocated for u-boot is too small for the latest u-boot
(>750KB). We need to increase it. eMMC uses a much bigger
area
(2MB).
eMMC: region "u-boot.img.raw" overlaps the environment area and the region"spl-os-image.raw".both: region "spl-os-image.raw" is quite small and can't handle android
kernelsFixing this requires growing some regions and moving others. Care has been taken to leave some room for further growth of "spl-os-args.raw".
Also the "env" now appears in the dfu so that it's apparent that the region is not free space that can be used to grow "u-boot.img.raw". The total space allocated for those raw binaries is 16MB, of which 13+MB
are reserved for the kernel image.Quoted 9 lines
Signed-off-by Jean-Jacques Hiblot <[email protected]>---
Sam,
This patch goes a bit further in changing the layout of the MMC than yours. However
it doesn't update the GPT partitioning. This would still be needed.Quoted 7 lines
Hi Jean-Jacques,
Got a couple of questions about this change and my patch (changing eMMC partitions table), about how to make them play nice together.
1. How DFU table is connected to eMMC partition table? And why my patch was interfering with DFU table?
AFAIK DFU is not related to GPT. I never used the GPT so I can't for sure
how it fits together.
My guess is thatenv_mmc.chas no idea that GPT even exists and uses raw
access to the eMMC. In this caseCONFIG_ENV_OFFSETmust be defined to point
at the beginning of your env partition and must be adapted when the GPT is
updated. The same goes for the DFU. Ideally GPT and DFU should use the same
layout (at least for MLO, u-boot, kernel and args).Quoted 4 lines
2. Can I change
CONFIG_ENV_OFFSET? Because my changes is going to move "reserved" partition on eMMC, where U-Boot environment is stored. Or it should be in sync with DFU table somehow? If yes -- we should work together to find solution that works best for both cases.Quoted 10 lines
CONFIG_ENV_OFFSETis loosely related to DFU: we don't update the environment
through DFU. However we must make sure that the area used to store the env
doesn't overlap a another region (MLO, u-boot, kernel, args). The dfu doesn't define those regions, it's done with #defines likeCONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR. But DFU exposes them for "remote"
upgrade.Quoted 2 lines
So if I change eMMC GPT partition table, it's ok for me to update
CONFIG_ENV_OFFSETas well, right?Yes you need to change it
Quoted 7 lines
Because in my case
CONFIG_ENV_OFFSET
is going to be different from the value your patch sets. In case of eMMC table, we're using "reserved" partition to store U-Boot environment, and I want it to be at 1664 KiB, which gives usCONFIG_ENV_OFFSET=0x1A0000. Is it ok if I change it to that value? Or something else must be changed along with it? If yes, then what exactly?You need to adapt DFU if you plan to use it. Maybe you can define a new layout for DFU, something like
dfu_alt_info_emmc_gptthat will reflect your
GPT layoutAnyway IMO it would be good to use the same offset/size for GPT and non-GPT
case for the following regions:
- MLO
- u-boot
- envFor MLO we already use the same: offset 128kB / size 256kB For u-boot, you increased the size to 1MB, I suggest that we increase it a
bit more (1.5MB or 2MB) just to make sure that we don't have to increase its
size again next year.
For the env, I suggest that the size is increased to 256kB to take care of
redundant env.Quoted 8 lines
Quoted 4 lines
Thank you for detailed explanation. I'm gonna get back to that task in a few weeks, don't have enough time right now. Once I come up with some particular patch, I will add you to reviewers, to be sure that DFU part is correct.
Before you switch to another task maybe we can agree on the offset and sizes for MLO, u-boot and env so that I can do the necessary changes on my side (dfu, #defines).
Quoted 5 lines
Sure. I agree with you that we should increase U-Boot partition. I'm gonna do next layout for eMMC table:
MLO: start=128K, size=256K U-Boot: size=2M
Sorry I took so long to reply.
I'd re-arrange the following 3 elements and make the dtb area bigger. At the moment DTBs are around 100k but they keep growing.
Quoted 3 lines
DTB: size=128K
misc: size=128K
U-Boot environment: size=256KU-Boot environment: size=256K
DTB: size=256K
misc: size=128K
JJ
Quoted 129 lines
efs: size=16M crypto: size=16K recovery: size=10M boot: size=10M system: size=768M cache: size=256M ipu1: size=1M ipu2: size=1M userdata: size=the rest of eMMC spaceIs it ok with you? Also, we should check if it's ok with Praneeth, as he mentioned that some changes to that table may be necessary in the future (from Android side).
Quoted 113 lines
Quoted 113 lines
Quoted 113 lines
Quoted 113 lines
Thanks.
Quoted 111 lines
Quoted 2 lines
3. What about my similar patch for AM57x EVM (see [1])? Is it fine, or it affects DFU table as well?
I guess it's OK because the env is stored in a FAT partition:
CONFIG_ENV_OFFSETis not usedQuoted 105 lines
Thanks.
[1] https://patchwork.ozlabs.org/patch/730736/
Quoted 101 lines
tested on DRA7. DFU updates ok for MMC and eMMC
Jean-Jacques
include/configs/dra7xx_evm.h | 2 +- include/configs/omap5_uevm.h | 2 +- include/configs/ti_armv7_common.h | 7 ++++--- include/environment/ti/dfu.h | 14 ++++++++------ 4 files changed, 14 insertions(+), 11 deletions(-)include/configs/dra7xx_evm.h +1
-1@@ -28,7 +28,7 @@#define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ #define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_OFFSET 0x220000#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)#define CONFIG_SYS_REDUNDAND_ENVIRONMENT #endifinclude/configs/omap5_uevm.h +1
-1@@ -38,7 +38,7 @@#define CONFIG_ENV_IS_IN_MMC #define CONFIG_SYS_MMC_ENV_DEV 1/* SLOT2: eMMC(1) */ #define CONFIG_ENV_SIZE (128 << 10) -#define CONFIG_ENV_OFFSET 0xE0000 +#define CONFIG_ENV_OFFSET 0x220000#define CONFIG_ENV_OFFSET_REDUND (CONFIG_ENV_OFFSET + CONFIG_ENV_SIZE)#define CONFIG_SYS_REDUNDAND_ENVIRONMENTinclude/configs/ti_armv7_common.h +0
-1@@ -282,9 +282,10 @@#define CONFIG_SPL_FS_LOAD_ARGS_NAME "args"/* RAW SD card / eMMC */ -#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x900/* address
0x120000*/
-#defineCONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR0x80/* address0x10000*/include/configs/ti_armv7_common.h +1
-1-#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x80/* 64KiB */ +#define CONFIG_SYS_MMCSD_RAW_MODE_KERNEL_SECTOR 0x1500/* address
0x2A0000*/
+#defineCONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTOR0x1300/* address0x260000*/include/configs/ti_armv7_common.h +2
-0+#define CONFIG_SYS_MMCSD_RAW_MODE_ARGS_SECTORS 0x100/* 128KiB */ +/* spl export command */ #define CONFIG_CMD_SPL include/environment/ti/dfu.h +8
-7@@ -12,9 +12,10 @@"rootfs part 0 2;" \"MLO fat 0 1;" \"MLO.raw raw 0x100 0x100;" \ -"u-boot.img.raw raw 0x300 0x400;" \ -"spl-os-args.raw raw 0x80 0x80;" \ -"spl-os-image.raw raw 0x900 0x2000;" \ +"u-boot.img.raw raw 0x300 0xE00;" \ +"u-env.raw raw 0x1100 0x200;" \ +"spl-os-args.raw raw 0x1300 0x100;" \ +"spl-os-image.raw raw 0x1500 0x6B00;" \"spl-os-args fat 0 1;" \"spl-os-image fat 0 1;" \"u-boot.img fat 0 1;" \@@ -27,9 +28,10 @@"rootfs part 1 2;" \"MLO fat 1 1;" \"MLO.raw raw 0x100 0x100;" \ -"u-boot.img.raw raw 0x300 0x1000;" \ -"spl-os-args.raw raw 0x80 0x80;" \ -"spl-os-image.raw raw 0x900 0x2000;" \ +"u-boot.img.raw raw 0x300 0xE00;" \ +"u-env.raw raw 0x1100 0x200;" \ +"spl-os-args.raw raw 0x1300 0x100;" \ +"spl-os-image.raw raw 0x1500 0x6B00;" \"spl-os-args fat 1 1;" \"spl-os-image fat 1 1;" \"u-boot.img fat 1 1;" \ --1.9.1
PATCH 1/1 arm: dra7xx: Update bootloader partition size
In reply to Sam ProtsenkoQuoted 9 lines · Sam Protsenko
The current size of U-Boot is already ~840 KiB.
This patch is to increase bootloader partition size up to 1 MiB and thereby fix flashing error.
Also fix U-Boot environment address on eMMC ("reserved" partition), as it's being shifted by above change.
Signed-off-by Sam Protsenko <[email protected]>
I know I'm late chiming in here, but I want to now, all the same. First, we need to explain _why_ things are getting so huge. The answer is that we're including so many (complete, from Linux) device trees. So we should probably update the comments around this area to note why the bootloader partition is so large, and then pick a good, large, and aligned with the underlying erase block size partition.
Signature · 8 lines
Tom -------------- next part -------------- A non-text attachment was scrubbed... Name: signature.asc Type: application/pgp-signature Size: 819 bytes Desc: Digital signature URL: <http://lists.denx.de/pipermail/u-boot/attachments/20170301/057e52d9/attachment.sig>
PATCH 1/1 arm: dra7xx: Update bootloader partition size
Quoted 10 lines · Tom Rini
Quoted 8 lines · Sam Protsenko
The current size of U-Boot is already ~840 KiB.
This patch is to increase bootloader partition size up to 1 MiB and thereby fix flashing error.
Also fix U-Boot environment address on eMMC ("reserved" partition), as it's being shifted by above change.
Quoted 9 lines
Quoted 1 line
Signed-off-by Sam Protsenko <[email protected]>I know I'm late chiming in here, but I want to now, all the same. First, we need to explain _why_ things are getting so huge. The answer is that we're including so many (complete, from Linux) device trees. So we should probably update the comments around this area to note why the bootloader partition is so large, and then pick a good, large, and aligned with the underlying erase block size partition.
Tom,
Your comment is absolutely correct, I was just in a little bit hurry when sending this patch. Please don't merge it yet, I'm gonna get back to it after Linaro Connect. Things you mentioned will be added to commit message, and we are probably going to change that partition size one more time. So let's hold on on this change for now.
Thanks.
Quoted 2 lines
--
Tom