Fix Adaptive Sync SDP for PR with Link ON + Auxless ALPM
Subsystems (3)
cover Fix Adaptive Sync SDP for PR with Link ON + Auxless ALPM
Enable Adaptive Sync SDP for Panel replay + auxless ALPM. First few patches are fixes in existing AS SDP enablement. Later patches add the support to send AS SDP for Panel replay with Link ON and with auxless ALPM (Link-Off).
This series is in continuation from discussions in [1] [2] and more recent [3]:
Apart from few patches from [3] new changes include:
- Some clean up in drm/dp Macros
- Add new DPCD bit to get FAVT PAYLOAD FIELDS PARSING SUPPORT.
- Add AS SDP version and PR and VRR specific bits in drm_dp.h.
- Modify AS SDP compute config to accomodate PR with Link On and Link Off.
- Program Downspread Ctrl DPCD bits.
- Make way for T1 and T2 AS SDP transmission timing/position.
[1] https://lore.kernel.org/all/[email protected]/
[2] https://lore.kernel.org/all/[email protected]/
[3] https://lore.kernel.org/intel-gfx/[email protected]/T/#m6e8beab2cc3b6ff9d61f740f107d83a2f4e08114
Rev2:
- Drop the redundant version member for AS SDP, and use the member revision
- Drop member to store AS SDP transmission time, use simple helper instead.
- Use Burst mode to write Panel Replay config DPCDs.
- Split AS SDP configuration in compute_config() and compute_config_late() phase.
- Always enable AS SDP whenever supported by source + sink.
Rev3:
- Use ASYNC_VIDEO_TIMING_NOT_SUPPORTED_IN_PR bit also to determine AS SDP v2 support.
- Drop patch to make provision to send AS SDP v1.
- Add patch to include all relevant AS SDP fields in comparison.
- Other refactor improvements suggested by Ville.
Ankit Nautiyal (19):
drm/dp: Rename and relocate AS SDP payload field masks drm/dp: Clean up DPRX feature enumeration macros
drm/dp: Add bits for AS SDP FAVT Payload Fields Parsing support drm/dp: Add DPCD for configuring AS SDP for PR + VRR drm/i915/dp: Fix readback for target_rr in Adaptive Sync SDP drm/i915/vrr: Avoid vrr for PCON with HDMI2.1 sink drm/i915/dp: Account for AS_SDP guardband only when enabled drm/i915/dp: Add a helper to decide if AS SDP can be used drm/i915/dp: Skip AS SDP for DP branch devices drm/i915/dp: Use revision field of AS SDP data structure drm/i915/dp: Include all relevant AS SDP fields in comparison drm/i915/dp: Add member to intel_dp to store AS SDP v2 support drm/i915/psr: Write the PR config DPCDs in burst mode drm/i915/display: Add helper for AS SDP transmission time selection drm/i915/psr: Program Panel Replay CONFIG3 using AS SDP transmission
time
drm/i915/dp: Set relevant Downspread Ctrl DPCD bits for PR + Auxless
ALPM
drm/i915/dp: Program AS SDP DB[1:0] for PR with Link off drm/i915/dp: Split AS SDP computation between compute_config and
compute_config_late
drm/i915/dp: Always enable AS SDP if supported by source + sink
drivers/gpu/drm/i915/display/intel_alpm.c | 20 ++- drivers/gpu/drm/i915/display/intel_display.c | 6 +- .../drm/i915/display/intel_display_types.h | 1 + drivers/gpu/drm/i915/display/intel_dp.c | 147 ++++++++++++++---- drivers/gpu/drm/i915/display/intel_dp.h | 2 + .../drm/i915/display/intel_dp_link_training.c | 10 +- .../drm/i915/display/intel_dp_link_training.h | 3 +- drivers/gpu/drm/i915/display/intel_dp_mst.c | 2 +- drivers/gpu/drm/i915/display/intel_psr.c | 30 ++-- drivers/gpu/drm/i915/display/intel_vrr.c | 10 ++ include/drm/display/drm_dp.h | 19 ++- 11 files changed, 194 insertions(+), 56 deletions(-)
Signature · 1 line
2.45.2
PATCH 1/19 drm/dp: Rename and relocate AS SDP payload field masks
The AS SDP payload field masks were misnamed and placed under the DPRX feature enumeration list. These are not DPRX capability bits, but are payload field masks for the Adaptive Sync SDP.
Relocate both masks next to the AS SDP definitions. Update users to the corrected names. No functional change.
--- drivers/gpu/drm/i915/display/intel_dp.c | 4 ++-- include/drm/display/drm_dp.h | 5 +++-- 2 files changed, 5 insertions(+), 4 deletions(-)
drivers/gpu/drm/i915/display/intel_dp.c +2 -2
@@ -5295,8 +5295,8 @@ int intel_dp_as_sdp_unpack(struct drm_dp_as_sdp *as_sdp,if ((sdp->sdp_header.HB3 &0x3F ) !=9 )return -EINVAL ; - as_sdp->length = sdp->sdp_header.HB3 &DP_ADAPTIVE_SYNC_SDP_LENGTH ; - as_sdp->mode = sdp->db[0 ] &DP_ADAPTIVE_SYNC_SDP_OPERATION_MODE ; + as_sdp->length = sdp->sdp_header.HB3 &DP_AS_SDP_LENGTH_MASK ; + as_sdp->mode = sdp->db[0 ] &DP_AS_SDP_OPERATION_MODE_MASK ; as_sdp->vtotal = (sdp->db[2 ] <<8 ) | sdp->db[1 ]; as_sdp->target_rr = (u64 )sdp->db[3 ] | ((u64 )sdp->db[4 ] &0x3 ); as_sdp->target_rr_divider = sdp->db[4 ] &0x20 ? true : false;
include/drm/display/drm_dp.h +3 -2
@@ -1204,8 +1204,6 @@#define DP_DPRX_FEATURE_ENUMERATION_LIST_CONT_1 0x2214/* 2.0 E11 */ # define DP_ADAPTIVE_SYNC_SDP_SUPPORTED (1 << 0) -# define DP_ADAPTIVE_SYNC_SDP_OPERATION_MODE GENMASK(1, 0) -# define DP_ADAPTIVE_SYNC_SDP_LENGTH GENMASK(5, 0)# define DP_AS_SDP_FIRST_HALF_LINE_OR_3840_PIXEL_CYCLE_WINDOW_NOT_SUPPORTED (1 << 1)# define DP_VSC_EXT_SDP_FRAMEWORK_VERSION_1_SUPPORTED (1 << 4)
@@ -1870,4 +1868,7 @@ enum operation_mode {DP_AS_SDP_FAVT_TRR_REACHED =0x03 }; +#define DP_AS_SDP_OPERATION_MODE_MASK GENMASK(1, 0) +#define DP_AS_SDP_LENGTH_MASK GENMASK(5, 0) +#endif /* _DRM_DP_H_ */
Signature · 1 line
2.45.2
PATCH 2/19 drm/dp: Clean up DPRX feature enumeration macros
In reply to Ankit NautiyalAlign the DP_DPRX feature enumeration macros for better readability and consistency, and use the BIT() macro instead of open-coded shifts.
--- include/drm/display/drm_dp.h | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
include/drm/display/drm_dp.h +4 -4
@@ -1202,10 +1202,10 @@# define DP_DPRX_SLEEP_WAKE_TIMEOUT_PERIOD_80_MS 0x04# define DP_DPRX_SLEEP_WAKE_TIMEOUT_PERIOD_100_MS 0x05 -#define DP_DPRX_FEATURE_ENUMERATION_LIST_CONT_1 0x2214/* 2.0 E11 */ -# define DP_ADAPTIVE_SYNC_SDP_SUPPORTED (1 << 0) -# define DP_AS_SDP_FIRST_HALF_LINE_OR_3840_PIXEL_CYCLE_WINDOW_NOT_SUPPORTED (1 << 1) -# define DP_VSC_EXT_SDP_FRAMEWORK_VERSION_1_SUPPORTED (1 << 4) +#define DP_DPRX_FEATURE_ENUMERATION_LIST_CONT_1 0x2214/* 2.0 E11 */ +# define DP_ADAPTIVE_SYNC_SDP_SUPPORTED BIT(0) +# define DP_AS_SDP_FIRST_HALF_LINE_OR_3840_PIXEL_CYCLE_WINDOW_NOT_SUPPORTED BIT(1) +# define DP_VSC_EXT_SDP_FRAMEWORK_VERSION_1_SUPPORTED BIT(4)#define DP_128B132B_SUPPORTED_LINK_RATES 0x2215/* 2.0 */ # define DP_UHBR10 (1 << 0)
Signature · 1 line
2.45.2
PATCH 3/19 drm/dp: Add bits for AS SDP FAVT Payload Fields Parsing support
In reply to Ankit NautiyalDP v2.1 introduced support for sending AS SDP payload bytes for FAVT. Add the relavant bits for the same.
--- include/drm/display/drm_dp.h | 1 + 1 file changed, 1 insertion(+)
include/drm/display/drm_dp.h +1 -0
@@ -1205,6 +1205,7 @@#define DP_DPRX_FEATURE_ENUMERATION_LIST_CONT_1 0x2214/* 2.0 E11 */ # define DP_ADAPTIVE_SYNC_SDP_SUPPORTED BIT(0)# define DP_AS_SDP_FIRST_HALF_LINE_OR_3840_PIXEL_CYCLE_WINDOW_NOT_SUPPORTED BIT(1) +# define DP_AS_SDP_FAVT_PAYLOAD_FIELDS_PARSING_SUPPORTED BIT(2)/* 2.1 */ # define DP_VSC_EXT_SDP_FRAMEWORK_VERSION_1_SUPPORTED BIT(4)#define DP_128B132B_SUPPORTED_LINK_RATES 0x2215/* 2.0 */
Signature · 1 line
2.45.2
PATCH 4/19 drm/dp: Add DPCD for configuring AS SDP for PR + VRR
In reply to Ankit NautiyalAdd additional DPCDs required to be configured to support VRR with Panel Replay. These DPCDs are specifically required for configuring Adaptive Sync SDP and are introduced in DP v2.1.
v2:
- Correct the shift for the bits. (Ville)
- Add DP_PR_ prefix for the PR-related fields.
v3:
- Use macro values in their shifted form to match the convention (Ville)
--- include/drm/display/drm_dp.h | 5 +++++ 1 file changed, 5 insertions(+)
include/drm/display/drm_dp.h +5 -0
@@ -775,6 +775,11 @@# define DP_PANEL_REPLAY_SU_Y_GRANULARITY_EXTENDED_VAL_SEL_MASK (0xf << 3)# define DP_PANEL_REPLAY_SU_REGION_SCANLINE_CAPTURE (1 << 7) +#define PANEL_REPLAY_CONFIG3 0x11a/* DP 2.1 */ +# define DP_PR_AS_SDP_SETUP_TIME_T1 (0 << 6) +# define DP_PR_AS_SDP_SETUP_TIME_DYNAMIC (1 << 6)/* DP 2.1 Table 2-227 */ +# define DP_PR_AS_SDP_SETUP_TIME_T2 (2 << 6) +#define DP_PAYLOAD_ALLOCATE_SET 0x1c0#define DP_PAYLOAD_ALLOCATE_START_TIME_SLOT 0x1c1#define DP_PAYLOAD_ALLOCATE_TIME_SLOT_COUNT 0x1c2
Signature · 1 line
2.45.2
Re: [PATCH 04/19] drm/dp: Add DPCD for configuring AS SDP for PR + VRR
Quoted 20 lines · Ankit Nautiyal
Add additional DPCDs required to be configured to support VRR with Panel Replay. These DPCDs are specifically required for configuring Adaptive Sync SDP and are introduced in DP v2.1.
v2:
- Correct the shift for the bits. (Ville)
- AddDP_PR_prefix for the PR-related fields.
v3:
- Use macro values in their shifted form to match the convention (Ville)Signed-off-by Ankit Nautiyal <[email protected]>--- include/drm/display/drm_dp.h | 5 +++++ 1 file changed, 5 insertions(+)include/drm/display/drm_dp.h +0
-0
include/drm/display/drm_dp.h line 778
Quoted 4 lines
include/drm/display/drm_dp.h +1
-0@@ -775,6 +775,11 @@# define DP_PANEL_REPLAY_SU_Y_GRANULARITY_EXTENDED_VAL_SEL_MASK (0xf << 3)# define DP_PANEL_REPLAY_SU_REGION_SCANLINE_CAPTURE (1 << 7) +#define PANEL_REPLAY_CONFIG3 0x11a/* DP 2.1 */
I would still define a DP_PR_AS_SDP_SETUP_TIME_MASK here, to make it clear which bits are part of this.
With that
Quoted 9 lines
include/drm/display/drm_dp.h +4
-0+# define DP_PR_AS_SDP_SETUP_TIME_T1 (0 << 6) +# define DP_PR_AS_SDP_SETUP_TIME_DYNAMIC (1 << 6)/* DP 2.1 Table 2-227 */ +# define DP_PR_AS_SDP_SETUP_TIME_T2 (2 << 6) +#define DP_PAYLOAD_ALLOCATE_SET 0x1c0#define DP_PAYLOAD_ALLOCATE_START_TIME_SLOT 0x1c1#define DP_PAYLOAD_ALLOCATE_TIME_SLOT_COUNT 0x1c2Signature · 1 line
2.45.2
Signature · 2 lines
Ville Syrjälä Intel
Re: [PATCH 04/19] drm/dp: Add DPCD for configuring AS SDP for PR + VRR
Quoted 24 lines · Ville Syrjälä
Quoted 23 lines · Ankit Nautiyal
Add additional DPCDs required to be configured to support VRR with Panel Replay. These DPCDs are specifically required for configuring Adaptive Sync SDP and are introduced in DP v2.1.
v2:
- Correct the shift for the bits. (Ville)
- AddDP_PR_prefix for the PR-related fields.
v3:
- Use macro values in their shifted form to match the convention (Ville)Signed-off-by Ankit Nautiyal <[email protected]>--- include/drm/display/drm_dp.h | 5 +++++ 1 file changed, 5 insertions(+)include/drm/display/drm_dp.h +0
-0@@ -775,6 +775,11 @@# define DP_PANEL_REPLAY_SU_Y_GRANULARITY_EXTENDED_VAL_SEL_MASK (0xf << 3)# define DP_PANEL_REPLAY_SU_REGION_SCANLINE_CAPTURE (1 << 7)
Quoted 3 lines
include/drm/display/drm_dp.h line 778
Quoted 1 line
include/drm/display/drm_dp.h +1
-0+#define PANEL_REPLAY_CONFIG3 0x11a/* DP 2.1 */ I would still define a
DP_PR_AS_SDP_SETUP_TIME_MASKhere, to make it clear which bits are part of this.
I think I added that in previous implementation, but dropped in this. I will add it again.
Regards,
Ankit
Quoted 13 lines
With that
Reviewed-by Ville Syrjälä <[email protected]>Quoted 9 lines
include/drm/display/drm_dp.h +4
-0+# define DP_PR_AS_SDP_SETUP_TIME_T1 (0 << 6) +# define DP_PR_AS_SDP_SETUP_TIME_DYNAMIC (1 << 6)/* DP 2.1 Table 2-227 */ +# define DP_PR_AS_SDP_SETUP_TIME_T2 (2 << 6) +#define DP_PAYLOAD_ALLOCATE_SET 0x1c0#define DP_PAYLOAD_ALLOCATE_START_TIME_SLOT 0x1c1#define DP_PAYLOAD_ALLOCATE_TIME_SLOT_COUNT 0x1c2Signature · 1 line
2.45.2
PATCH 5/19 drm/i915/dp: Fix readback for target_rr in Adaptive Sync SDP
In reply to Ankit NautiyalCorrect the bit-shift logic to properly readback the 10 bit target_rr from DB3 and DB4.
v2: Align the style with readback for vtotal. (Ville)
--- drivers/gpu/drm/i915/display/intel_dp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/i915/display/intel_dp.c +1 -1
@@ -5298,7 +5298,7 @@ int intel_dp_as_sdp_unpack(struct drm_dp_as_sdp *as_sdp, as_sdp->length = sdp->sdp_header.HB3 &DP_AS_SDP_LENGTH_MASK ; as_sdp->mode = sdp->db[0 ] &DP_AS_SDP_OPERATION_MODE_MASK ; as_sdp->vtotal = (sdp->db[2 ] <<8 ) | sdp->db[1 ]; - as_sdp->target_rr = (u64 )sdp->db[3 ] | ((u64 )sdp->db[4 ] &0x3 ); + as_sdp->target_rr = ((sdp->db[4 ] &0x3 ) <<8 ) | sdp->db[3 ]; as_sdp->target_rr_divider = sdp->db[4 ] &0x20 ? true : false;return 0 ;
Signature · 1 line
2.45.2
PATCH 6/19 drm/i915/vrr: Avoid vrr for PCON with HDMI2.1 sink
In reply to Ankit NautiyalCurrently we do not support VRR with HDMI so skip vrr compute config step for all DP branch devices.
v2: Restrict VRR on all DP branch devices instead for checking only for
HDMI. (Ville)
--- drivers/gpu/drm/i915/display/intel_vrr.c | 10 ++++++++++ 1 file changed, 10 insertions(+)
drivers/gpu/drm/i915/display/intel_vrr.c +10 -0
@@ -55,6 +55,16 @@ bool intel_vrr_is_capable(struct intel_connector *connector)if (connector->mst.dp)return false; intel_dp =intel_attached_dp (connector); +/* +* Among non-MST DP branch devices, only an HDMI 2.1 sink connected +* via a PCON could support VRR. However, supporting VRR through a +* PCON requires non-trivial changes that are not implemented yet. +* Until that support exists, avoid VRR on all DP branch devices. +* +* TODO: Add support for VRR for DP->HDMI 2.1 PCON. +*/ +if (drm_dp_is_branch (intel_dp->dpcd)) +return false;if (!drm_dp_sink_can_do_video_without_timing_msa (intel_dp->dpcd))return false;
Signature · 1 line
2.45.2
PATCH 7/19 drm/i915/dp: Account for AS_SDP guardband only when enabled
In reply to Ankit NautiyalCurrently the intel_dp_sdp_min_guardband() accounts for AS_SDP for all platforms that support adaptive sync SDP even for configurations where it cannot be enabled. Instead account for adaptive sync SDP guardband only when it is enabled.
--- drivers/gpu/drm/i915/display/intel_dp.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-)
drivers/gpu/drm/i915/display/intel_dp.c +2 -3
@@ -7374,7 +7374,6 @@ int intel_dp_get_lines_for_sdp(const struct intel_crtc_state *crtc_state, u32 tyint intel_dp_sdp_min_guardband (const struct intel_crtc_state *crtc_state,bool assume_all_enabled) { -struct intel_display *display =to_intel_display (crtc_state);int sdp_guardband =0 ; if (assume_all_enabled ||
@@ -7389,8 +7388,8 @@ int intel_dp_sdp_min_guardband(const struct intel_crtc_state *crtc_state, sdp_guardband =max (sdp_guardband,intel_dp_get_lines_for_sdp (crtc_state,DP_SDP_PPS )); -if ((assume_all_enabled &&HAS_AS_SDP (display)) || - crtc_state->infoframes.enable &intel_hdmi_infoframe_enable (DP_SDP_ADAPTIVE_SYNC )) +if (crtc_state->infoframes.enable & +intel_hdmi_infoframe_enable (DP_SDP_ADAPTIVE_SYNC )) sdp_guardband =max (sdp_guardband,intel_dp_get_lines_for_sdp (crtc_state,DP_SDP_ADAPTIVE_SYNC ));
Signature · 1 line
2.45.2
Re: [PATCH 07/19] drm/i915/dp: Account for AS_SDP guardband only when enabled
Quoted 6 lines · Ankit Nautiyal
Currently the
intel_dp_sdp_min_guardband()accounts forAS_SDPfor all platforms that support adaptive sync SDP even for configurations where it cannot be enabled. Instead account for adaptive sync SDP guardband only when it is enabled.Signed-off-by Ankit Nautiyal <[email protected]>
Quoted 29 lines
--- drivers/gpu/drm/i915/display/intel_dp.c | 5 ++--- 1 file changed, 2 insertions(+), 3 deletions(-)drivers/gpu/drm/i915/display/intel_dp.c +2
-3@@ -7374,7 +7374,6 @@ int intel_dp_get_lines_for_sdp(const struct intel_crtc_state *crtc_state, u32 tyint intel_dp_sdp_min_guardband (const struct intel_crtc_state *crtc_state,bool assume_all_enabled) { -struct intel_display *display =to_intel_display (crtc_state);int sdp_guardband =0 ; if (assume_all_enabled ||@@ -7389,8 +7388,8 @@ int intel_dp_sdp_min_guardband(const struct intel_crtc_state *crtc_state, sdp_guardband =max (sdp_guardband,intel_dp_get_lines_for_sdp (crtc_state,DP_SDP_PPS )); -if ((assume_all_enabled &&HAS_AS_SDP (display)) || - crtc_state->infoframes.enable &intel_hdmi_infoframe_enable (DP_SDP_ADAPTIVE_SYNC )) +if (crtc_state->infoframes.enable & +intel_hdmi_infoframe_enable (DP_SDP_ADAPTIVE_SYNC )) sdp_guardband =max (sdp_guardband,intel_dp_get_lines_for_sdp (crtc_state,DP_SDP_ADAPTIVE_SYNC ));Signature · 1 line
2.45.2
Signature · 2 lines
Ville Syrjälä Intel
PATCH 8/19 drm/i915/dp: Add a helper to decide if AS SDP can be used
In reply to Ankit NautiyalAdd a helper that determines whether AS SDP can be used for the current DP configuration. For now this is true only when the sink supports AS SDP and VRR is enabled, but more conditions may be added later.
--- drivers/gpu/drm/i915/display/intel_dp.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-)
drivers/gpu/drm/i915/display/intel_dp.c +10 -1
@@ -3124,6 +3124,15 @@ static void intel_dp_compute_vsc_colorimetry(const struct intel_crtc_state *crtc vsc->content_type =DP_CONTENT_TYPE_NOT_DEFINED ; } +static bool intel_dp_can_use_as_sdp (struct intel_dp *intel_dp, +struct intel_crtc_state *crtc_state) +{ +if (!intel_dp->as_sdp_supported) +return false; + +return crtc_state->vrr.enable; +} +static void intel_dp_compute_as_sdp (struct intel_dp *intel_dp,struct intel_crtc_state *crtc_state) {
@@ -3131,7 +3140,7 @@ static void intel_dp_compute_as_sdp(struct intel_dp *intel_dp,const struct drm_display_mode *adjusted_mode = &crtc_state->hw.adjusted_mode; -if (!crtc_state->vrr.enable || !intel_dp->as_sdp_supported) +if (!intel_dp_can_use_as_sdp (intel_dp, crtc_state))return ; crtc_state->infoframes.enable |=intel_hdmi_infoframe_enable (DP_SDP_ADAPTIVE_SYNC );
Signature · 1 line
2.45.2
Re: [PATCH 08/19] drm/i915/dp: Add a helper to decide if AS SDP can be used
Quoted 15 lines · Ankit Nautiyal
Add a helper that determines whether AS SDP can be used for the current DP configuration. For now this is true only when the sink supports AS SDP and VRR is enabled, but more conditions may be added later.
Signed-off-by Ankit Nautiyal <[email protected]>--- drivers/gpu/drm/i915/display/intel_dp.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/display/intel_dp.c +0
-0
drivers/gpu/drm/i915/display/intel_dp.c static void intel_dp_compute_vsc_colorimetry(const struct intel_crtc_state *crtc · line 3132
Quoted 9 lines
drivers/gpu/drm/i915/display/intel_dp.c +6
-0@@ -3124,6 +3124,15 @@ static void intel_dp_compute_vsc_colorimetry(const struct intel_crtc_state *crtc vsc->content_type =DP_CONTENT_TYPE_NOT_DEFINED ; } +static bool intel_dp_can_use_as_sdp (struct intel_dp *intel_dp, +struct intel_crtc_state *crtc_state) +{ +if (!intel_dp->as_sdp_supported) +return false; +
Could have a FIXME here about fastset being borked with this. Didn't read far enough in the series yet to see if you did anything about that.
Either way
Quoted 17 lines
drivers/gpu/drm/i915/display/intel_dp.c +4
-1+return crtc_state->vrr.enable; +} +static void intel_dp_compute_as_sdp (struct intel_dp *intel_dp,struct intel_crtc_state *crtc_state) {@@ -3131,7 +3140,7 @@ static void intel_dp_compute_as_sdp(struct intel_dp *intel_dp,const struct drm_display_mode *adjusted_mode = &crtc_state->hw.adjusted_mode; -if (!crtc_state->vrr.enable || !intel_dp->as_sdp_supported) +if (!intel_dp_can_use_as_sdp (intel_dp, crtc_state))return ; crtc_state->infoframes.enable |=intel_hdmi_infoframe_enable (DP_SDP_ADAPTIVE_SYNC );Signature · 1 line
2.45.2
Signature · 2 lines
Ville Syrjälä Intel
Re: [PATCH 08/19] drm/i915/dp: Add a helper to decide if AS SDP can be used
Quoted 19 lines · Ville Syrjälä
Quoted 18 lines · Ankit Nautiyal
Add a helper that determines whether AS SDP can be used for the current DP configuration. For now this is true only when the sink supports AS SDP and VRR is enabled, but more conditions may be added later.
Signed-off-by Ankit Nautiyal <[email protected]>--- drivers/gpu/drm/i915/display/intel_dp.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/display/intel_dp.c +0
-0@@ -3124,6 +3124,15 @@ static void intel_dp_compute_vsc_colorimetry(const struct intel_crtc_state *crtc vsc->content_type =DP_CONTENT_TYPE_NOT_DEFINED ; }
Quoted 2 lines
drivers/gpu/drm/i915/display/intel_dp.c static void intel_dp_compute_vsc_colorimetry(const struct intel_crtc_state *crtc · line 3128
Quoted 2 lines
drivers/gpu/drm/i915/display/intel_dp.c +2
-0+static bool intel_dp_can_use_as_sdp (struct intel_dp *intel_dp, +struct intel_crtc_state *crtc_state)
Hmm. Maybe the name should be .._need_as_sdp() or something like that instead. I can imagine many cases when we could use the AS SDP but don't have to.
Quoted 32 lines
drivers/gpu/drm/i915/display/intel_dp.c static void intel_dp_compute_vsc_colorimetry(const struct intel_crtc_state *crtc · line 3132
Quoted 4 lines
drivers/gpu/drm/i915/display/intel_dp.c +4
-0+{ +if (!intel_dp->as_sdp_supported) +return false; +Could have a FIXME here about fastset being borked with this. Didn't read far enough in the series yet to see if you did anything about that.
Either way
Reviewed-by Ville Syrjälä <[email protected]>Quoted 17 lines
drivers/gpu/drm/i915/display/intel_dp.c +4
-1+return crtc_state->vrr.enable; +} +static void intel_dp_compute_as_sdp (struct intel_dp *intel_dp,struct intel_crtc_state *crtc_state) {@@ -3131,7 +3140,7 @@ static void intel_dp_compute_as_sdp(struct intel_dp *intel_dp,const struct drm_display_mode *adjusted_mode = &crtc_state->hw.adjusted_mode; -if (!crtc_state->vrr.enable || !intel_dp->as_sdp_supported) +if (!intel_dp_can_use_as_sdp (intel_dp, crtc_state))return ; crtc_state->infoframes.enable |=intel_hdmi_infoframe_enable (DP_SDP_ADAPTIVE_SYNC );Signature · 1 line
2.45.2Signature · 2 lines
Ville Syrjälä Intel
Signature · 2 lines
Ville Syrjälä Intel
Re: [PATCH 08/19] drm/i915/dp: Add a helper to decide if AS SDP can be used
Quoted 20 lines · Ville Syrjälä
Quoted 19 lines · Ville Syrjälä
Quoted 18 lines · Ankit Nautiyal
Add a helper that determines whether AS SDP can be used for the current DP configuration. For now this is true only when the sink supports AS SDP and VRR is enabled, but more conditions may be added later.
Signed-off-by Ankit Nautiyal <[email protected]>--- drivers/gpu/drm/i915/display/intel_dp.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/display/intel_dp.c +0
-0@@ -3124,6 +3124,15 @@ static void intel_dp_compute_vsc_colorimetry(const struct intel_crtc_state *crtc vsc->content_type =DP_CONTENT_TYPE_NOT_DEFINED ; }
Quoted 5 lines
Quoted 2 lines
drivers/gpu/drm/i915/display/intel_dp.c static void intel_dp_compute_vsc_colorimetry(const struct intel_crtc_state *crtc · line 3128
Quoted 2 lines
drivers/gpu/drm/i915/display/intel_dp.c +2
-0+static bool intel_dp_can_use_as_sdp (struct intel_dp *intel_dp, +struct intel_crtc_state *crtc_state)Hmm. Maybe the name should be .._need_as_sdp() or something like that instead. I can imagine many cases when we could use the AS SDP but don't have to.
Roger that. Will rename this to ..._needs_as_sdp().
Regards,
Ankit
Quoted 31 lines
Quoted 31 lines
drivers/gpu/drm/i915/display/intel_dp.c static void intel_dp_compute_vsc_colorimetry(const struct intel_crtc_state *crtc · line 3132
Quoted 5 lines
drivers/gpu/drm/i915/display/intel_dp.c +4
-0+{ +if (!intel_dp->as_sdp_supported) +return false; +Could have a FIXME here about fastset being borked with this. Didn't read far enough in the series yet to see if you did anything about that.
Either way
Reviewed-by Ville Syrjälä <[email protected]>Quoted 17 lines
drivers/gpu/drm/i915/display/intel_dp.c +4
-1+return crtc_state->vrr.enable; +} +static void intel_dp_compute_as_sdp (struct intel_dp *intel_dp,struct intel_crtc_state *crtc_state) {@@ -3131,7 +3140,7 @@ static void intel_dp_compute_as_sdp(struct intel_dp *intel_dp,const struct drm_display_mode *adjusted_mode = &crtc_state->hw.adjusted_mode; -if (!crtc_state->vrr.enable || !intel_dp->as_sdp_supported) +if (!intel_dp_can_use_as_sdp (intel_dp, crtc_state))return ; crtc_state->infoframes.enable |=intel_hdmi_infoframe_enable (DP_SDP_ADAPTIVE_SYNC );Signature · 1 line
2.45.2Signature · 2 lines
Ville Syrjälä Intel
Re: [PATCH 08/19] drm/i915/dp: Add a helper to decide if AS SDP can be used
In reply to Ville SyrjäläQuoted 19 lines · Ville Syrjälä
Quoted 18 lines · Ankit Nautiyal
Add a helper that determines whether AS SDP can be used for the current DP configuration. For now this is true only when the sink supports AS SDP and VRR is enabled, but more conditions may be added later.
Signed-off-by Ankit Nautiyal <[email protected]>--- drivers/gpu/drm/i915/display/intel_dp.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/display/intel_dp.c +0
-0@@ -3124,6 +3124,15 @@ static void intel_dp_compute_vsc_colorimetry(const struct intel_crtc_state *crtc vsc->content_type =DP_CONTENT_TYPE_NOT_DEFINED ; }
Quoted 8 lines
drivers/gpu/drm/i915/display/intel_dp.c static void intel_dp_compute_vsc_colorimetry(const struct intel_crtc_state *crtc · line 3132
Quoted 6 lines
drivers/gpu/drm/i915/display/intel_dp.c +6
-0+static bool intel_dp_can_use_as_sdp (struct intel_dp *intel_dp, +struct intel_crtc_state *crtc_state) +{ +if (!intel_dp->as_sdp_supported) +return false; +Could have a FIXME here about fastset being borked with this. Didn't read far enough in the series yet to see if you did anything about that.
Hmm... let me check if I understand your concern correctly.
When VRR state changes through the fastset path, intel_dp_as_sdp_compute_config_late() will compute different AS SDP fields.
We do write the new values to the SDP DIP registers during update_pipe, but since AS SDP comparison is skipped during fastset,
we have no way to verify through state readback that the hardware actually latched the new values correctly.
Is that what you had in mind?
I'll add a FIXME about this.
Thanks,
Ankit
Quoted 21 lines
Either way
Reviewed-by Ville Syrjälä <[email protected]>Quoted 17 lines
drivers/gpu/drm/i915/display/intel_dp.c +4
-1+return crtc_state->vrr.enable; +} +static void intel_dp_compute_as_sdp (struct intel_dp *intel_dp,struct intel_crtc_state *crtc_state) {@@ -3131,7 +3140,7 @@ static void intel_dp_compute_as_sdp(struct intel_dp *intel_dp,const struct drm_display_mode *adjusted_mode = &crtc_state->hw.adjusted_mode; -if (!crtc_state->vrr.enable || !intel_dp->as_sdp_supported) +if (!intel_dp_can_use_as_sdp (intel_dp, crtc_state))return ; crtc_state->infoframes.enable |=intel_hdmi_infoframe_enable (DP_SDP_ADAPTIVE_SYNC );Signature · 1 line
2.45.2
Re: [PATCH 08/19] drm/i915/dp: Add a helper to decide if AS SDP can be used
Quoted 30 lines · Ankit K
Quoted 19 lines · Ville Syrjälä
Quoted 18 lines · Ankit Nautiyal
Add a helper that determines whether AS SDP can be used for the current DP configuration. For now this is true only when the sink supports AS SDP and VRR is enabled, but more conditions may be added later.
Signed-off-by Ankit Nautiyal <[email protected]>--- drivers/gpu/drm/i915/display/intel_dp.c | 11 ++++++++++- 1 file changed, 10 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/display/intel_dp.c +0
-0@@ -3124,6 +3124,15 @@ static void intel_dp_compute_vsc_colorimetry(const struct intel_crtc_state *crtc vsc->content_type =DP_CONTENT_TYPE_NOT_DEFINED ; }Quoted 8 lines
drivers/gpu/drm/i915/display/intel_dp.c static void intel_dp_compute_vsc_colorimetry(const struct intel_crtc_state *crtc · line 3132
Quoted 6 lines
drivers/gpu/drm/i915/display/intel_dp.c +6
-0+static bool intel_dp_can_use_as_sdp (struct intel_dp *intel_dp, +struct intel_crtc_state *crtc_state) +{ +if (!intel_dp->as_sdp_supported) +return false; +Could have a FIXME here about fastset being borked with this. Didn't read far enough in the series yet to see if you did anything about that.
Quoted 7 lines
Hmm... let me check if I understand your concern correctly.
When VRR state changes through the fastset path,
intel_dp_as_sdp_compute_config_late()will compute different AS SDP fields.We do write the new values to the SDP DIP registers during
update_pipe, but since AS SDP comparison is skipped during fastset,
Oh, I thought we didn't have that. If it's there then I guess it's fine-ish. Although we don't do the infoframe/SDP updates in the truly proper atomic fashion, nor do we handle the new cdclk->tc clock crossing thing correctly. So I suspect we might end up sending a corrupted packet if the update happens to straddle the transmission line.
Quoted 33 lines
we have no way to verify through state readback that the hardware actually latched the new values correctly.
Is that what you had in mind?
I'll add a FIXME about this.
Thanks,
Ankit
Quoted 21 lines
Either way
Reviewed-by Ville Syrjälä <[email protected]>Quoted 17 lines
drivers/gpu/drm/i915/display/intel_dp.c +4
-1+return crtc_state->vrr.enable; +} +static void intel_dp_compute_as_sdp (struct intel_dp *intel_dp,struct intel_crtc_state *crtc_state) {@@ -3131,7 +3140,7 @@ static void intel_dp_compute_as_sdp(struct intel_dp *intel_dp,const struct drm_display_mode *adjusted_mode = &crtc_state->hw.adjusted_mode; -if (!crtc_state->vrr.enable || !intel_dp->as_sdp_supported) +if (!intel_dp_can_use_as_sdp (intel_dp, crtc_state))return ; crtc_state->infoframes.enable |=intel_hdmi_infoframe_enable (DP_SDP_ADAPTIVE_SYNC );Signature · 1 line
2.45.2
Signature · 2 lines
Ville Syrjälä Intel
PATCH 9/19 drm/i915/dp: Skip AS SDP for DP branch devices
In reply to Ankit NautiyalCurrently, VRR is not implmented for DP branch devices. So skip sending AS SDP for them.
--- drivers/gpu/drm/i915/display/intel_dp.c | 6 ++++++ 1 file changed, 6 insertions(+)
drivers/gpu/drm/i915/display/intel_dp.c +6 -0
@@ -3130,6 +3130,12 @@ static bool intel_dp_can_use_as_sdp(struct intel_dp *intel_dp,if (!intel_dp->as_sdp_supported)return false; +/* +* #TODO Implement AS SDP for DP branch device. +*/ +if (drm_dp_is_branch (intel_dp->dpcd)) +return false; +return crtc_state->vrr.enable; }
Signature · 1 line
2.45.2
Re: [PATCH 09/19] drm/i915/dp: Skip AS SDP for DP branch devices
Quoted 2 lines · Ankit Nautiyal
Currently, VRR is not implmented for DP branch devices. So skip sending AS SDP for them.
Sure why not.
Quoted 25 lines
Signed-off-by Ankit Nautiyal <[email protected]>--- drivers/gpu/drm/i915/display/intel_dp.c | 6 ++++++ 1 file changed, 6 insertions(+)drivers/gpu/drm/i915/display/intel_dp.c +6
-0@@ -3130,6 +3130,12 @@ static bool intel_dp_can_use_as_sdp(struct intel_dp *intel_dp,if (!intel_dp->as_sdp_supported)return false; +/* +* #TODO Implement AS SDP for DP branch device. +*/ +if (drm_dp_is_branch (intel_dp->dpcd)) +return false; +return crtc_state->vrr.enable; }Signature · 1 line
2.45.2
Signature · 2 lines
Ville Syrjälä Intel
PATCH 10/19 drm/i915/dp: Use revision field of AS SDP data structure
In reply to Ankit NautiyalUse the revision field of struct drm_dp_as_sdp instead of current hardcoding for the AS SDP revisions.
--- drivers/gpu/drm/i915/display/intel_display.c | 3 ++- drivers/gpu/drm/i915/display/intel_dp.c | 7 +++---- 2 files changed, 5 insertions(+), 5 deletions(-)
drivers/gpu/drm/i915/display/intel_display.c +2 -1
@@ -4906,7 +4906,8 @@ static bool intel_compare_dp_as_sdp(const struct drm_dp_as_sdp *a, const struct drm_dp_as_sdp *b) { - return a->vtotal == b->vtotal && + return a->revision == b->revision && + a->vtotal == b->vtotal && a->target_rr == b->target_rr && a->duration_incr_ms == b->duration_incr_ms && a->duration_decr_ms == b->duration_decr_ms &&
drivers/gpu/drm/i915/display/intel_dp.c +3 -4
@@ -3154,6 +3154,7 @@ static void intel_dp_compute_as_sdp(struct intel_dp *intel_dp, as_sdp->sdp_type =DP_SDP_ADAPTIVE_SYNC ; as_sdp->length =0x9 ; as_sdp->duration_incr_ms =0 ; + as_sdp->revision =0x2 ; as_sdp->vtotal =intel_vrr_vmin_vtotal (crtc_state);if (crtc_state->cmrr.enable) {
@@ -5117,7 +5118,7 @@ static ssize_t intel_dp_as_sdp_pack(const struct drm_dp_as_sdp *as_sdp,/* Prepare AS (Adaptive Sync) SDP Header */ sdp->sdp_header.HB0 =0 ; sdp->sdp_header.HB1 = as_sdp->sdp_type; - sdp->sdp_header.HB2 =0x02 ; + sdp->sdp_header.HB2 = as_sdp->revision; sdp->sdp_header.HB3 = as_sdp->length;/* Fill AS (Adaptive Sync) SDP Payload */
@@ -5304,13 +5305,11 @@ int intel_dp_as_sdp_unpack(struct drm_dp_as_sdp *as_sdp,if (sdp->sdp_header.HB1 !=DP_SDP_ADAPTIVE_SYNC )return -EINVAL ; -if (sdp->sdp_header.HB2 !=0x02 ) -return -EINVAL ; -if ((sdp->sdp_header.HB3 &0x3F ) !=9 )return -EINVAL ; as_sdp->length = sdp->sdp_header.HB3 &DP_AS_SDP_LENGTH_MASK ; + as_sdp->revision = sdp->sdp_header.HB2; as_sdp->mode = sdp->db[0 ] &DP_AS_SDP_OPERATION_MODE_MASK ; as_sdp->vtotal = (sdp->db[2 ] <<8 ) | sdp->db[1 ]; as_sdp->target_rr = ((sdp->db[4 ] &0x3 ) <<8 ) | sdp->db[3 ];
Signature · 1 line
2.45.2
PATCH 11/19 drm/i915/dp: Include all relevant AS SDP fields in comparison
In reply to Ankit NautiyalAdd missing drm_dp_as_sdp header fields to intel_compare_dp_as_sdp() comparison.
--- drivers/gpu/drm/i915/display/intel_display.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)
drivers/gpu/drm/i915/display/intel_display.c +4 -1
@@ -4906,11 +4906,14 @@ static bool intel_compare_dp_as_sdp(const struct drm_dp_as_sdp *a, const struct drm_dp_as_sdp *b) { - return a->revision == b->revision && + return a->sdp_type == b->sdp_type && + a->revision == b->revision && + a->length == b->length && a->vtotal == b->vtotal && a->target_rr == b->target_rr && a->duration_incr_ms == b->duration_incr_ms && a->duration_decr_ms == b->duration_decr_ms && + a->target_rr_divider == b->target_rr_divider && a->mode == b->mode; }
Signature · 1 line
2.45.2
Re: [PATCH 11/19] drm/i915/dp: Include all relevant AS SDP fields in comparison
Quoted 16 lines · Ankit Nautiyal
Add missing
drm_dp_as_sdpheader fields tointel_compare_dp_as_sdp()comparison.Signed-off-by Ankit Nautiyal <[email protected]>--- drivers/gpu/drm/i915/display/intel_display.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/display/intel_display.c +0
-0@@ -4906,11 +4906,14 @@ static bool intel_compare_dp_as_sdp(const struct drm_dp_as_sdp *a, const struct drm_dp_as_sdp *b) {
drivers/gpu/drm/i915/display/intel_display.c static bool · line 4917
Quoted 10 lines
drivers/gpu/drm/i915/display/intel_display.c +4
-1-return a->revision == b->revision && +return a->sdp_type == b->sdp_type && + a->revision == b->revision && + a->length == b->length && a->vtotal == b->vtotal && a->target_rr == b->target_rr && a->duration_incr_ms == b->duration_incr_ms && a->duration_decr_ms == b->duration_decr_ms && + a->target_rr_divider == b->target_rr_divider && a->mode == b->mode;
BTW do we know if the hardware actually modifies the AS SDP DIP buffer, or does it just override some of the values as the SDP is being transmitted? If the former then I guess we have to keep in mind that the readout may have to do some sanitizing to avoid mismatches, if we do anything that require the hardware to dynamically adjust the AS SDP.
Quoted 4 lines
drivers/gpu/drm/i915/display/intel_display.c +0
-0}Signature · 1 line
2.45.2
Signature · 2 lines
Ville Syrjälä Intel
Re: [PATCH 11/19] drm/i915/dp: Include all relevant AS SDP fields in comparison
Quoted 25 lines · Ville Syrjälä
Quoted 24 lines · Ankit Nautiyal
Add missing
drm_dp_as_sdpheader fields tointel_compare_dp_as_sdp()comparison.Signed-off-by Ankit Nautiyal <[email protected]>--- drivers/gpu/drm/i915/display/intel_display.c | 5 ++++- 1 file changed, 4 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/display/intel_display.c +3
-1@@ -4906,11 +4906,14 @@ static bool intel_compare_dp_as_sdp(const struct drm_dp_as_sdp *a, const struct drm_dp_as_sdp *b) { - return a->revision == b->revision && + return a->sdp_type == b->sdp_type && + a->revision == b->revision && + a->length == b->length && a->vtotal == b->vtotal && a->target_rr == b->target_rr && a->duration_incr_ms == b->duration_incr_ms && a->duration_decr_ms == b->duration_decr_ms &&
Quoted 8 lines
drivers/gpu/drm/i915/display/intel_display.c static bool · line 4917
Quoted 2 lines
drivers/gpu/drm/i915/display/intel_display.c +1
-0+ a->target_rr_divider == b->target_rr_divider && a->mode == b->mode;BTW do we know if the hardware actually modifies the AS SDP DIP buffer, or does it just override some of the values as the SDP is being transmitted? If the former then I guess we have to keep in mind that the readout may have to do some sanitizing to avoid mismatches, if we do anything that require the hardware to dynamically adjust the AS SDP.
There are some things HW sends on its own like bits 2 and 3 of DB0 :
- Adaptive sync SDP transmission disable Bit 2 and
- Remote frame buffer update Bit 3
I think it overrides those values instead of modifying the SDP DIP buffer. That’s what the spec implies I suppose.
"When PR ALPM is Active (AS SDP Version 2), hardware will automatically drive DB0[3:2]. Software should always program these bits to zero."
Regards,
Ankit
Quoted 7 lines
Reviewed-by Ville Syrjälä <[email protected]>Quoted 4 lines
drivers/gpu/drm/i915/display/intel_display.c +0
-0}Signature · 1 line
2.45.2
PATCH 12/19 drm/i915/dp: Add member to intel_dp to store AS SDP v2 support
In reply to Ankit NautiyalDP v2.1 SCR advertises support for FAVT payload fields parsing in DPCD 0x2214 Bit 2. This indicates the support for Adaptive-Sync SDP version 2 (AS SDP v2), which allows the source to set the version in HB2[4:0] and the payload length in HB3[5:0] of the AS SDP header.
DP v2.1 SCR also adds a bit for Async Video Timing during Panel Replay, in Panel Replay Capability DPCD 0x00b1 (Bit 3). When this bit is cleared, the sink supports asynchronous video timing while in a Panel Replay Active state. The spec mandates that such sinks shall support AS SDP v2.
Infer AS SDP v2 support from these capabilities and store it in struct intel_dp for use by subsequent feature enablement changes.
v2:
- Include parsing ASYNC_VIDEO_TIMING_NOT_SUPPORTED_IN_PR bit to determine AS SDP v2 support. (Ville)
--- .../drm/i915/display/intel_display_types.h | 1 + drivers/gpu/drm/i915/display/intel_dp.c | 37 +++++++++++++++++++ 2 files changed, 38 insertions(+)
drivers/gpu/drm/i915/display/intel_display_types.h +1 -0
@@ -1870,6 +1870,7 @@ struct intel_dp {/* connector directly attached - won't be use for modeset in mst world */ struct intel_connector *attached_connector;bool as_sdp_supported; +bool as_sdp_v2_supported;struct drm_dp_tunnel *tunnel; bool tunnel_suspended:1;
drivers/gpu/drm/i915/display/intel_dp.c +37 -0
@@ -6301,6 +6301,40 @@ intel_dp_unset_edid(struct intel_dp *intel_dp) false); } +static bool +intel_dp_sink_supports_as_sdp_v2 (struct intel_dp *intel_dp) +{ +u8 rx_features; +u8 pr_caps; + +/* +* The DP spec does not explicitly provide the AS SDP v2 capability. +* So based on the DP v2.1 SCR, we infer it from the following bits: +* +* DP_AS_SDP_FAVT_PAYLOAD_FIELDS_PARSING_SUPPORTED indicates support for +* FAVT, which is explicitly defined to use AS SDP v2. +* +* DP_ASYNC_VIDEO_TIMING_NOT_SUPPORTED_IN_PR cleared indicates support +* for Async Video timing in PR active and the spec mandates that such +* sinks shall support AS SDP v2. +*/ +if (drm_dp_dpcd_read_byte (&intel_dp->aux, +DP_DPRX_FEATURE_ENUMERATION_LIST_CONT_1 , + &rx_features) ==1 ) { +if (rx_features &DP_AS_SDP_FAVT_PAYLOAD_FIELDS_PARSING_SUPPORTED ) +return true; + } + +if (drm_dp_dpcd_read_byte (&intel_dp->aux, +DP_PANEL_REPLAY_CAP_CAPABILITY , + &pr_caps) ==1 ) { +if (!(pr_caps &DP_PANEL_REPLAY_ASYNC_VIDEO_TIMING_NOT_SUPPORTED_IN_PR )) +return true; + } + +return false; +} +static void intel_dp_detect_sdp_caps (struct intel_dp *intel_dp) {
@@ -6308,6 +6342,9 @@ intel_dp_detect_sdp_caps(struct intel_dp *intel_dp) intel_dp->as_sdp_supported =HAS_AS_SDP (display) &&drm_dp_as_sdp_supported (&intel_dp->aux, intel_dp->dpcd); + + intel_dp->as_sdp_v2_supported = intel_dp->as_sdp_supported && +intel_dp_sink_supports_as_sdp_v2 (intel_dp); }static bool intel_dp_needs_dpcd_probe (struct intel_dp *intel_dp,bool force_on_external)
Signature · 1 line
2.45.2
Re: [PATCH 12/19] drm/i915/dp: Add member to intel_dp to store AS SDP v2 support
Quoted 61 lines · Ankit Nautiyal
DP v2.1 SCR advertises support for FAVT payload fields parsing in DPCD
0x2214Bit 2. This indicates the support for Adaptive-Sync SDP version 2 (AS SDP v2), which allows the source to set the version in HB2[4:0] and the payload length in HB3[5:0] of the AS SDP header.DP v2.1 SCR also adds a bit for Async Video Timing during Panel Replay, in Panel Replay Capability DPCD
0x00b1(Bit 3). When this bit is cleared, the sink supports asynchronous video timing while in a Panel Replay Active state. The spec mandates that such sinks shall support AS SDP v2.Infer AS SDP v2 support from these capabilities and store it in struct
intel_dpfor use by subsequent feature enablement changes.v2:
- Include parsingASYNC_VIDEO_TIMING_NOT_SUPPORTED_IN_PRbit to determine AS SDP v2 support. (Ville)Signed-off-by Ankit Nautiyal <[email protected]>--- .../drm/i915/display/intel_display_types.h | 1 + drivers/gpu/drm/i915/display/intel_dp.c | 37 +++++++++++++++++++ 2 files changed, 38 insertions(+)drivers/gpu/drm/i915/display/intel_display_types.h +1
-0@@ -1870,6 +1870,7 @@ struct intel_dp {/* connector directly attached - won't be use for modeset in mst world */ struct intel_connector *attached_connector;bool as_sdp_supported; +bool as_sdp_v2_supported;struct drm_dp_tunnel *tunnel; bool tunnel_suspended:1;drivers/gpu/drm/i915/display/intel_dp.c +18
-0@@ -6301,6 +6301,40 @@ intel_dp_unset_edid(struct intel_dp *intel_dp) false); } +static bool +intel_dp_sink_supports_as_sdp_v2 (struct intel_dp *intel_dp) +{ +u8 rx_features; +u8 pr_caps; + +/* +* The DP spec does not explicitly provide the AS SDP v2 capability. +* So based on the DP v2.1 SCR, we infer it from the following bits: +* +* DP_AS_SDP_FAVT_PAYLOAD_FIELDS_PARSING_SUPPORTED indicates support for +* FAVT, which is explicitly defined to use AS SDP v2. +* +* DP_ASYNC_VIDEO_TIMING_NOT_SUPPORTED_IN_PR cleared indicates support +* for Async Video timing in PR active and the spec mandates that such +* sinks shall support AS SDP v2. +*/ + if (drm_dp_dpcd_read_byte(&intel_dp->aux,
drivers/gpu/drm/i915/display/intel_dp.c intel_dp_unset_edid(struct intel_dp *intel_dp) · line 6331
Quoted 10 lines
drivers/gpu/drm/i915/display/intel_dp.c +10
-0+ DP_DPRX_FEATURE_ENUMERATION_LIST_CONT_1, + &rx_features) == 1) { +if (rx_features &DP_AS_SDP_FAVT_PAYLOAD_FIELDS_PARSING_SUPPORTED ) +return true; + } + +if (drm_dp_dpcd_read_byte (&intel_dp->aux, +DP_PANEL_REPLAY_CAP_CAPABILITY , + &pr_caps) ==1 ) { +if (!(pr_caps &DP_PANEL_REPLAY_ASYNC_VIDEO_TIMING_NOT_SUPPORTED_IN_PR ))
That seems to be backwards. If the sink requires AS SDP then it will set the bit.
Quoted 21 lines
drivers/gpu/drm/i915/display/intel_dp.c +9
-0+return true; + } + +return false; +} +static void intel_dp_detect_sdp_caps (struct intel_dp *intel_dp) {@@ -6308,6 +6342,9 @@ intel_dp_detect_sdp_caps(struct intel_dp *intel_dp) intel_dp->as_sdp_supported =HAS_AS_SDP (display) &&drm_dp_as_sdp_supported (&intel_dp->aux, intel_dp->dpcd); + + intel_dp->as_sdp_v2_supported = intel_dp->as_sdp_supported && +intel_dp_sink_supports_as_sdp_v2 (intel_dp); }static bool intel_dp_needs_dpcd_probe (struct intel_dp *intel_dp,bool force_on_external)Signature · 1 line
2.45.2
Signature · 2 lines
Ville Syrjälä Intel
Re: [PATCH 12/19] drm/i915/dp: Add member to intel_dp to store AS SDP v2 support
Quoted 66 lines · Ville Syrjälä
Quoted 65 lines · Ankit Nautiyal
DP v2.1 SCR advertises support for FAVT payload fields parsing in DPCD
0x2214Bit 2. This indicates the support for Adaptive-Sync SDP version 2 (AS SDP v2), which allows the source to set the version in HB2[4:0] and the payload length in HB3[5:0] of the AS SDP header.DP v2.1 SCR also adds a bit for Async Video Timing during Panel Replay, in Panel Replay Capability DPCD
0x00b1(Bit 3). When this bit is cleared, the sink supports asynchronous video timing while in a Panel Replay Active state. The spec mandates that such sinks shall support AS SDP v2.Infer AS SDP v2 support from these capabilities and store it in struct
intel_dpfor use by subsequent feature enablement changes.v2:
- Include parsingASYNC_VIDEO_TIMING_NOT_SUPPORTED_IN_PRbit to determine AS SDP v2 support. (Ville)Signed-off-by Ankit Nautiyal <[email protected]>--- .../drm/i915/display/intel_display_types.h | 1 + drivers/gpu/drm/i915/display/intel_dp.c | 37 +++++++++++++++++++ 2 files changed, 38 insertions(+)drivers/gpu/drm/i915/display/intel_display_types.h +1
-0@@ -1870,6 +1870,7 @@ struct intel_dp {/* connector directly attached - won't be use for modeset in mst world */ struct intel_connector *attached_connector;bool as_sdp_supported; +bool as_sdp_v2_supported;struct drm_dp_tunnel *tunnel; bool tunnel_suspended:1;drivers/gpu/drm/i915/display/intel_dp.c +22
-0@@ -6301,6 +6301,40 @@ intel_dp_unset_edid(struct intel_dp *intel_dp) false); } +static bool +intel_dp_sink_supports_as_sdp_v2 (struct intel_dp *intel_dp) +{ +u8 rx_features; +u8 pr_caps; + +/* +* The DP spec does not explicitly provide the AS SDP v2 capability. +* So based on the DP v2.1 SCR, we infer it from the following bits: +* +* DP_AS_SDP_FAVT_PAYLOAD_FIELDS_PARSING_SUPPORTED indicates support for +* FAVT, which is explicitly defined to use AS SDP v2. +* +* DP_ASYNC_VIDEO_TIMING_NOT_SUPPORTED_IN_PR cleared indicates support +* for Async Video timing in PR active and the spec mandates that such +* sinks shall support AS SDP v2. +*/ +if (drm_dp_dpcd_read_byte (&intel_dp->aux, +DP_DPRX_FEATURE_ENUMERATION_LIST_CONT_1 , + &rx_features) ==1 ) { +if (rx_features &DP_AS_SDP_FAVT_PAYLOAD_FIELDS_PARSING_SUPPORTED ) +return true;
Quoted 8 lines
drivers/gpu/drm/i915/display/intel_dp.c intel_dp_unset_edid(struct intel_dp *intel_dp) · line 6331
Quoted 6 lines
drivers/gpu/drm/i915/display/intel_dp.c +6
-0+ } + +if (drm_dp_dpcd_read_byte (&intel_dp->aux, +DP_PANEL_REPLAY_CAP_CAPABILITY , + &pr_caps) ==1 ) { +if (!(pr_caps &DP_PANEL_REPLAY_ASYNC_VIDEO_TIMING_NOT_SUPPORTED_IN_PR ))That seems to be backwards. If the sink requires AS SDP then it will set the bit.
Hmm.. I indeed got it backwards, you are right.
If Async Video timing is supported then re-set the bit. But in that case AS SDP is not required.
So reset means AS SDP not required; bit set means it is required.
Thanks, I will correct this in next version.
Regards,
Ankit
Quoted 22 lines
Quoted 22 lines
drivers/gpu/drm/i915/display/intel_dp.c +9
-0+return true; + } + +return false; +} +static void intel_dp_detect_sdp_caps (struct intel_dp *intel_dp) {@@ -6308,6 +6342,9 @@ intel_dp_detect_sdp_caps(struct intel_dp *intel_dp) intel_dp->as_sdp_supported =HAS_AS_SDP (display) &&drm_dp_as_sdp_supported (&intel_dp->aux, intel_dp->dpcd); + + intel_dp->as_sdp_v2_supported = intel_dp->as_sdp_supported && +intel_dp_sink_supports_as_sdp_v2 (intel_dp); }static bool intel_dp_needs_dpcd_probe (struct intel_dp *intel_dp,bool force_on_external)Signature · 1 line
2.45.2
PATCH 13/19 drm/i915/psr: Write the PR config DPCDs in burst mode
In reply to Ankit NautiyalReplace the consecutive single-byte writes to PANEL_REPLAY_CONFIG and CONFIG2 with one drm_dp_dpcd_write() burst starting at PANEL_REPLAY_CONFIG, reducing AUX transactions.
v2: Drop extra conditions, and optimize variables. (Ville)
--- drivers/gpu/drm/i915/display/intel_psr.c | 29 ++++++++++++++---------- 1 file changed, 17 insertions(+), 12 deletions(-)
drivers/gpu/drm/i915/display/intel_psr.c +17 -12
@@ -782,27 +782,32 @@ static bool psr2_su_region_et_valid(struct intel_connector *connector, bool panestatic void _panel_replay_enable_sink (struct intel_dp *intel_dp,const struct intel_crtc_state *crtc_state) { -u8 val =DP_PANEL_REPLAY_ENABLE | -DP_PANEL_REPLAY_VSC_SDP_CRC_EN | -DP_PANEL_REPLAY_UNRECOVERABLE_ERROR_EN | -DP_PANEL_REPLAY_RFB_STORAGE_ERROR_EN | -DP_PANEL_REPLAY_ACTIVE_FRAME_CRC_ERROR_EN ; -u8 panel_replay_config2 =DP_PANEL_REPLAY_CRC_VERIFICATION ; +struct intel_display *display =to_intel_display (intel_dp); +u8 panel_replay_config[2 ]; +int ret; + + panel_replay_config[0 ] =DP_PANEL_REPLAY_ENABLE | +DP_PANEL_REPLAY_VSC_SDP_CRC_EN | +DP_PANEL_REPLAY_UNRECOVERABLE_ERROR_EN | +DP_PANEL_REPLAY_RFB_STORAGE_ERROR_EN | +DP_PANEL_REPLAY_ACTIVE_FRAME_CRC_ERROR_EN ; + panel_replay_config[1 ] =DP_PANEL_REPLAY_CRC_VERIFICATION ;if (crtc_state->has_sel_update) - val |=DP_PANEL_REPLAY_SU_ENABLE ; + panel_replay_config[0 ] |=DP_PANEL_REPLAY_SU_ENABLE ;if (crtc_state->enable_psr2_su_region_et) - val |=DP_PANEL_REPLAY_ENABLE_SU_REGION_ET ; + panel_replay_config[0 ] |=DP_PANEL_REPLAY_ENABLE_SU_REGION_ET ;if (crtc_state->req_psr2_sdp_prior_scanline) - panel_replay_config2 |= + panel_replay_config[1 ] |=DP_PANEL_REPLAY_SU_REGION_SCANLINE_CAPTURE ; -drm_dp_dpcd_writeb (&intel_dp->aux,PANEL_REPLAY_CONFIG , val); + ret =drm_dp_dpcd_write (&intel_dp->aux,PANEL_REPLAY_CONFIG , + panel_replay_config,sizeof (panel_replay_config)); -drm_dp_dpcd_writeb (&intel_dp->aux,PANEL_REPLAY_CONFIG2 , - panel_replay_config2); +if (ret !=sizeof (panel_replay_config)) +drm_dbg_kms (display->drm,"Failed to write Panel Replay Configs\n" ); } static void _psr_enable_sink(struct intel_dp *intel_dp,
Signature · 1 line
2.45.2
Re: [PATCH 13/19] drm/i915/psr: Write the PR config DPCDs in burst mode
Quoted 48 lines · Ankit Nautiyal
Replace the consecutive single-byte writes to
PANEL_REPLAY_CONFIGand CONFIG2 with onedrm_dp_dpcd_write()burst starting atPANEL_REPLAY_CONFIG, reducing AUX transactions.v2: Drop extra conditions, and optimize variables. (Ville)
Suggested-by Ville Syrjälä <[email protected]>Signed-off-by Ankit Nautiyal <[email protected]>--- drivers/gpu/drm/i915/display/intel_psr.c | 29 ++++++++++++++---------- 1 file changed, 17 insertions(+), 12 deletions(-)drivers/gpu/drm/i915/display/intel_psr.c +13
-9@@ -782,27 +782,32 @@ static bool psr2_su_region_et_valid(struct intel_connector *connector, bool panestatic void _panel_replay_enable_sink (struct intel_dp *intel_dp,const struct intel_crtc_state *crtc_state) { -u8 val =DP_PANEL_REPLAY_ENABLE | -DP_PANEL_REPLAY_VSC_SDP_CRC_EN | -DP_PANEL_REPLAY_UNRECOVERABLE_ERROR_EN | -DP_PANEL_REPLAY_RFB_STORAGE_ERROR_EN | -DP_PANEL_REPLAY_ACTIVE_FRAME_CRC_ERROR_EN ; -u8 panel_replay_config2 =DP_PANEL_REPLAY_CRC_VERIFICATION ; +struct intel_display *display =to_intel_display (intel_dp); +u8 panel_replay_config[2 ]; +int ret; + + panel_replay_config[0 ] =DP_PANEL_REPLAY_ENABLE | +DP_PANEL_REPLAY_VSC_SDP_CRC_EN | +DP_PANEL_REPLAY_UNRECOVERABLE_ERROR_EN | +DP_PANEL_REPLAY_RFB_STORAGE_ERROR_EN | +DP_PANEL_REPLAY_ACTIVE_FRAME_CRC_ERROR_EN ; + panel_replay_config[1 ] =DP_PANEL_REPLAY_CRC_VERIFICATION ;if (crtc_state->has_sel_update) - val |=DP_PANEL_REPLAY_SU_ENABLE ; + panel_replay_config[0 ] |=DP_PANEL_REPLAY_SU_ENABLE ;if (crtc_state->enable_psr2_su_region_et) - val |=DP_PANEL_REPLAY_ENABLE_SU_REGION_ET ; + panel_replay_config[0 ] |=DP_PANEL_REPLAY_ENABLE_SU_REGION_ET ;if (crtc_state->req_psr2_sdp_prior_scanline) - panel_replay_config2 |= + panel_replay_config[1] |=
drivers/gpu/drm/i915/display/intel_psr.c static bool psr2_su_region_et_valid(struct intel_connector *connector, bool pane · line 810
Quoted 10 lines
drivers/gpu/drm/i915/display/intel_psr.c +4
-3DP_PANEL_REPLAY_SU_REGION_SCANLINE_CAPTURE ; -drm_dp_dpcd_writeb (&intel_dp->aux,PANEL_REPLAY_CONFIG , val); + ret =drm_dp_dpcd_write (&intel_dp->aux,PANEL_REPLAY_CONFIG , + panel_replay_config,sizeof (panel_replay_config)); -drm_dp_dpcd_writeb (&intel_dp->aux,PANEL_REPLAY_CONFIG2 , - panel_replay_config2); +if (ret !=sizeof (panel_replay_config)) +drm_dbg_kms (display->drm,"Failed to write Panel Replay Configs\n" );
Looks like we don't actually check for errors on any of the other DPCD accesses here. So I'd probably drop it here as well.
Either way
Quoted 5 lines
drivers/gpu/drm/i915/display/intel_psr.c +0
-0} static void _psr_enable_sink(struct intel_dp *intel_dp,Signature · 1 line
2.45.2
Signature · 2 lines
Ville Syrjälä Intel
Re: [PATCH 13/19] drm/i915/psr: Write the PR config DPCDs in burst mode
Quoted 55 lines · Ville Syrjälä
Quoted 54 lines · Ankit Nautiyal
Replace the consecutive single-byte writes to
PANEL_REPLAY_CONFIGand CONFIG2 with onedrm_dp_dpcd_write()burst starting atPANEL_REPLAY_CONFIG, reducing AUX transactions.v2: Drop extra conditions, and optimize variables. (Ville)
Suggested-by Ville Syrjälä <[email protected]>Signed-off-by Ankit Nautiyal <[email protected]>--- drivers/gpu/drm/i915/display/intel_psr.c | 29 ++++++++++++++---------- 1 file changed, 17 insertions(+), 12 deletions(-)drivers/gpu/drm/i915/display/intel_psr.c +15
-10@@ -782,27 +782,32 @@ static bool psr2_su_region_et_valid(struct intel_connector *connector, bool panestatic void _panel_replay_enable_sink (struct intel_dp *intel_dp,const struct intel_crtc_state *crtc_state) { -u8 val =DP_PANEL_REPLAY_ENABLE | -DP_PANEL_REPLAY_VSC_SDP_CRC_EN | -DP_PANEL_REPLAY_UNRECOVERABLE_ERROR_EN | -DP_PANEL_REPLAY_RFB_STORAGE_ERROR_EN | -DP_PANEL_REPLAY_ACTIVE_FRAME_CRC_ERROR_EN ; -u8 panel_replay_config2 =DP_PANEL_REPLAY_CRC_VERIFICATION ; +struct intel_display *display =to_intel_display (intel_dp); +u8 panel_replay_config[2 ]; +int ret; + + panel_replay_config[0 ] =DP_PANEL_REPLAY_ENABLE | +DP_PANEL_REPLAY_VSC_SDP_CRC_EN | +DP_PANEL_REPLAY_UNRECOVERABLE_ERROR_EN | +DP_PANEL_REPLAY_RFB_STORAGE_ERROR_EN | +DP_PANEL_REPLAY_ACTIVE_FRAME_CRC_ERROR_EN ; + panel_replay_config[1 ] =DP_PANEL_REPLAY_CRC_VERIFICATION ;if (crtc_state->has_sel_update) - val |=DP_PANEL_REPLAY_SU_ENABLE ; + panel_replay_config[0 ] |=DP_PANEL_REPLAY_SU_ENABLE ;if (crtc_state->enable_psr2_su_region_et) - val |=DP_PANEL_REPLAY_ENABLE_SU_REGION_ET ; + panel_replay_config[0 ] |=DP_PANEL_REPLAY_ENABLE_SU_REGION_ET ;if (crtc_state->req_psr2_sdp_prior_scanline) - panel_replay_config2 |= + panel_replay_config[1 ] |=DP_PANEL_REPLAY_SU_REGION_SCANLINE_CAPTURE ; -drm_dp_dpcd_writeb (&intel_dp->aux,PANEL_REPLAY_CONFIG , val); + ret =drm_dp_dpcd_write (&intel_dp->aux,PANEL_REPLAY_CONFIG , + panel_replay_config,sizeof (panel_replay_config));
Quoted 6 lines
drivers/gpu/drm/i915/display/intel_psr.c static bool psr2_su_region_et_valid(struct intel_connector *connector, bool pane · line 810
Quoted 4 lines
drivers/gpu/drm/i915/display/intel_psr.c +2
-2-drm_dp_dpcd_writeb (&intel_dp->aux,PANEL_REPLAY_CONFIG2 , - panel_replay_config2); +if (ret !=sizeof (panel_replay_config)) +drm_dbg_kms (display->drm,"Failed to write Panel Replay Configs\n" );Looks like we don't actually check for errors on any of the other DPCD accesses here. So I'd probably drop it here as well.
Yeah.. will drop the error message.
Thanks,
Ankit
Quoted 9 lines
Either way
Reviewed-by Ville Syrjälä <[email protected]>Quoted 5 lines
drivers/gpu/drm/i915/display/intel_psr.c +0
-0} static void _psr_enable_sink(struct intel_dp *intel_dp,Signature · 1 line
2.45.2
PATCH 14/19 drm/i915/display: Add helper for AS SDP transmission time selection
In reply to Ankit NautiyalAS SDP may be transmitted at T1 or T2 depending on Panel Replay and Adaptive Sync SDP configuration as per DP 2.1. Current we are using T1 only, but future PR/AS SDP modes/features may require T2 or dynamic selection.
Introduce a helper to return the appropriate AS SDP transmission time so that a single value is consistently used for programming PR_ALPM. For now this returns T1.
v2: Avoid adding new member to crtc_state; use a helper. (Ville)
v3: Clarify why AS SDP transmission time is fixed to T1. (Ville)
Bspec: 68920
--- drivers/gpu/drm/i915/display/intel_alpm.c | 20 +++++++++++++++++++- drivers/gpu/drm/i915/display/intel_dp.c | 11 +++++++++++ drivers/gpu/drm/i915/display/intel_dp.h | 2 ++ 3 files changed, 32 insertions(+), 1 deletion(-)
drivers/gpu/drm/i915/display/intel_alpm.c +19 -1
@@ -11,6 +11,7 @@#include "intel_crtc.h" #include "intel_de.h" #include "intel_display_types.h" +#include "intel_display_utils.h" #include "intel_dp.h" #include "intel_dp_aux.h" #include "intel_psr.h"
@@ -359,6 +360,23 @@ void intel_alpm_lobf_compute_config(struct intel_dp *intel_dp, crtc_state->has_lobf = true; } +static u32 get_pr_alpm_as_sdp_transmission_time (const struct intel_crtc_state *crtc_state) +{ +int as_sdp_setup_time =intel_dp_as_sdp_transmission_time (); + +switch (as_sdp_setup_time) { +case DP_PR_AS_SDP_SETUP_TIME_T1 : +return PR_ALPM_CTL_ADAPTIVE_SYNC_SDP_POSITION_T1 ; +case DP_PR_AS_SDP_SETUP_TIME_DYNAMIC : +return PR_ALPM_CTL_ADAPTIVE_SYNC_SDP_POSITION_T1_OR_T2 ; +case DP_PR_AS_SDP_SETUP_TIME_T2 : +return PR_ALPM_CTL_ADAPTIVE_SYNC_SDP_POSITION_T2 ; +default : +MISSING_CASE (as_sdp_setup_time); +return PR_ALPM_CTL_ADAPTIVE_SYNC_SDP_POSITION_T1 ; + } +} +static void lnl_alpm_configure (struct intel_dp *intel_dp,const struct intel_crtc_state *crtc_state) {
@@ -382,7 +400,7 @@ static void lnl_alpm_configure(struct intel_dp *intel_dp,ALPM_CTL_AUX_LESS_WAKE_TIME (crtc_state->alpm_state.aux_less_wake_lines);if (intel_dp->as_sdp_supported) { -u32 pr_alpm_ctl =PR_ALPM_CTL_ADAPTIVE_SYNC_SDP_POSITION_T1 ; +u32 pr_alpm_ctl =get_pr_alpm_as_sdp_transmission_time (crtc_state);if (crtc_state->link_off_after_as_sdp_when_pr_active) pr_alpm_ctl |=PR_ALPM_CTL_ALLOW_LINK_OFF_BETWEEN_AS_SDP_AND_SU ;
drivers/gpu/drm/i915/display/intel_dp.c +11 -0
@@ -7465,3 +7465,14 @@ bool intel_dp_joiner_candidate_valid(struct intel_connector *connector,return true; } + +int intel_dp_as_sdp_transmission_time (void ) +{ +/* +* DP allows AS SDP position to move during PR active in some cases, but +* software-controlled refresh rate changes with DC6v / ALPM require the +* AS SDP to remain at T1. Use T1 unconditionally for now. +*/ + +return DP_PR_AS_SDP_SETUP_TIME_T1 ; +}
drivers/gpu/drm/i915/display/intel_dp.h +2 -0
@@ -238,4 +238,6 @@ bool intel_dp_joiner_candidate_valid(struct intel_connector *connector,for ((__num_joined_pipes) =1 ; (__num_joined_pipes) <= (I915_MAX_PIPES ); (__num_joined_pipes)++) \ for_each_if(intel_dp_joiner_candidate_valid(__connector, (__mode)->hdisplay, __num_joined_pipes)) +int intel_dp_as_sdp_transmission_time (void ); +#endif /* __INTEL_DP_H__ */
Signature · 1 line
2.45.2
Re: [PATCH 14/19] drm/i915/display: Add helper for AS SDP transmission time selection
Quoted 70 lines · Ankit Nautiyal
AS SDP may be transmitted at T1 or T2 depending on Panel Replay and Adaptive Sync SDP configuration as per DP 2.1. Current we are using T1 only, but future PR/AS SDP modes/features may require T2 or dynamic selection.
Introduce a helper to return the appropriate AS SDP transmission time so that a single value is consistently used for programming
PR_ALPM. For now this returns T1.v2: Avoid adding new member to
crtc_state; use a helper. (Ville)
v3: Clarify why AS SDP transmission time is fixed to T1. (Ville)Bspec: 68920
Signed-off-by Ankit Nautiyal <[email protected]>--- drivers/gpu/drm/i915/display/intel_alpm.c | 20 +++++++++++++++++++- drivers/gpu/drm/i915/display/intel_dp.c | 11 +++++++++++ drivers/gpu/drm/i915/display/intel_dp.h | 2 ++ 3 files changed, 32 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/display/intel_alpm.c +19
-1@@ -11,6 +11,7 @@#include "intel_crtc.h" #include "intel_de.h" #include "intel_display_types.h" +#include "intel_display_utils.h" #include "intel_dp.h" #include "intel_dp_aux.h" #include "intel_psr.h" @@ -359,6 +360,23 @@ void intel_alpm_lobf_compute_config(struct intel_dp *intel_dp, crtc_state->has_lobf = true; } +static u32 get_pr_alpm_as_sdp_transmission_time (const struct intel_crtc_state *crtc_state) +{ +int as_sdp_setup_time =intel_dp_as_sdp_transmission_time (); + +switch (as_sdp_setup_time) { +case DP_PR_AS_SDP_SETUP_TIME_T1 : +return PR_ALPM_CTL_ADAPTIVE_SYNC_SDP_POSITION_T1 ; +case DP_PR_AS_SDP_SETUP_TIME_DYNAMIC : +return PR_ALPM_CTL_ADAPTIVE_SYNC_SDP_POSITION_T1_OR_T2 ; +case DP_PR_AS_SDP_SETUP_TIME_T2 : +return PR_ALPM_CTL_ADAPTIVE_SYNC_SDP_POSITION_T2 ; +default : +MISSING_CASE (as_sdp_setup_time); +return PR_ALPM_CTL_ADAPTIVE_SYNC_SDP_POSITION_T1 ; + } +} +static void lnl_alpm_configure (struct intel_dp *intel_dp,const struct intel_crtc_state *crtc_state) {@@ -382,7 +400,7 @@ static void lnl_alpm_configure(struct intel_dp *intel_dp,ALPM_CTL_AUX_LESS_WAKE_TIME (crtc_state->alpm_state.aux_less_wake_lines);if (intel_dp->as_sdp_supported) { -u32 pr_alpm_ctl =PR_ALPM_CTL_ADAPTIVE_SYNC_SDP_POSITION_T1 ; +u32 pr_alpm_ctl =get_pr_alpm_as_sdp_transmission_time (crtc_state);if (crtc_state->link_off_after_as_sdp_when_pr_active) pr_alpm_ctl |=PR_ALPM_CTL_ALLOW_LINK_OFF_BETWEEN_AS_SDP_AND_SU ;drivers/gpu/drm/i915/display/intel_dp.c +0
-0
drivers/gpu/drm/i915/display/intel_dp.c bool intel_dp_joiner_candidate_valid(struct intel_connector *connector, · line 7469
Quoted 5 lines
drivers/gpu/drm/i915/display/intel_dp.c +2
-0@@ -7465,3 +7465,14 @@ bool intel_dp_joiner_candidate_valid(struct intel_connector *connector,return true; } + +int intel_dp_as_sdp_transmission_time (void )
This is a DPCD register value, so u8 would seem like the more appropriate return type.
With that
Quoted 22 lines
drivers/gpu/drm/i915/display/intel_dp.c +9
-0+{ +/* +* DP allows AS SDP position to move during PR active in some cases, but +* software-controlled refresh rate changes with DC6v / ALPM require the +* AS SDP to remain at T1. Use T1 unconditionally for now. +*/ + +return DP_PR_AS_SDP_SETUP_TIME_T1 ; +}drivers/gpu/drm/i915/display/intel_dp.h +2
-0@@ -238,4 +238,6 @@ bool intel_dp_joiner_candidate_valid(struct intel_connector *connector,for ((__num_joined_pipes) =1 ; (__num_joined_pipes) <= (I915_MAX_PIPES ); (__num_joined_pipes)++) \ for_each_if(intel_dp_joiner_candidate_valid(__connector, (__mode)->hdisplay, __num_joined_pipes)) +int intel_dp_as_sdp_transmission_time (void ); +#endif /* __INTEL_DP_H__ */ Signature · 1 line
2.45.2
Signature · 2 lines
Ville Syrjälä Intel
PATCH 15/19 drm/i915/psr: Program Panel Replay CONFIG3 using AS SDP transmission time
In reply to Ankit NautiyalPanel Replay requires the AS SDP transmission time to be written into PANEL_REPLAY_CONFIG3. This field was previously not programmed.
Use the AS SDP transmission-time helper to populate CONFIG3.
--- drivers/gpu/drm/i915/display/intel_psr.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)
drivers/gpu/drm/i915/display/intel_psr.c +2 -1
@@ -783,7 +783,7 @@ static void _panel_replay_enable_sink(struct intel_dp *intel_dp, const struct intel_crtc_state *crtc_state) {struct intel_display *display =to_intel_display (intel_dp); -u8 panel_replay_config[2 ]; +u8 panel_replay_config[3 ];int ret; panel_replay_config[0] = DP_PANEL_REPLAY_ENABLE |
@@ -792,6 +792,7 @@ static void _panel_replay_enable_sink(struct intel_dp *intel_dp,DP_PANEL_REPLAY_RFB_STORAGE_ERROR_EN |DP_PANEL_REPLAY_ACTIVE_FRAME_CRC_ERROR_EN ; panel_replay_config[1 ] =DP_PANEL_REPLAY_CRC_VERIFICATION ; + panel_replay_config[2 ] =intel_dp_as_sdp_transmission_time ();if (crtc_state->has_sel_update) panel_replay_config[0 ] |=DP_PANEL_REPLAY_SU_ENABLE ;
Signature · 1 line
2.45.2
Re: [PATCH 15/19] drm/i915/psr: Program Panel Replay CONFIG3 using AS SDP transmission time
Quoted 24 lines · Ankit Nautiyal
Panel Replay requires the AS SDP transmission time to be written into
PANEL_REPLAY_CONFIG3. This field was previously not programmed.Use the AS SDP transmission-time helper to populate CONFIG3.
Signed-off-by Ankit Nautiyal <[email protected]>--- drivers/gpu/drm/i915/display/intel_psr.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/display/intel_psr.c +1
-1@@ -783,7 +783,7 @@ static void _panel_replay_enable_sink(struct intel_dp *intel_dp, const struct intel_crtc_state *crtc_state) {struct intel_display *display =to_intel_display (intel_dp); -u8 panel_replay_config[2 ]; +u8 panel_replay_config[3 ];int ret; panel_replay_config[0] = DP_PANEL_REPLAY_ENABLE |
drivers/gpu/drm/i915/display/intel_psr.c static void _panel_replay_enable_sink(struct intel_dp *intel_dp, · line 795
Quoted 4 lines
drivers/gpu/drm/i915/display/intel_psr.c +1
-0@@ -792,6 +792,7 @@ static void _panel_replay_enable_sink(struct intel_dp *intel_dp,DP_PANEL_REPLAY_RFB_STORAGE_ERROR_EN |DP_PANEL_REPLAY_ACTIVE_FRAME_CRC_ERROR_EN ; panel_replay_config[1 ] =DP_PANEL_REPLAY_CRC_VERIFICATION ; + panel_replay_config[2 ] =intel_dp_as_sdp_transmission_time ();
PANEL_REPLAY_CONFIG3 0x11a
...PANEL_REPLAY_CONFIG1 0x1b0PANEL_REPLAY_CONFIG2 0x1b1
So apparently we can't do the burst write for all three :/
Looks like 0x1b2 is not used for anything so don't really understand why it wasn't added there. Oh well.
Quoted 5 lines
drivers/gpu/drm/i915/display/intel_psr.c +0
-0if (crtc_state->has_sel_update) panel_replay_config[0 ] |=DP_PANEL_REPLAY_SU_ENABLE ;Signature · 1 line
2.45.2
Signature · 2 lines
Ville Syrjälä Intel
Re: [PATCH 15/19] drm/i915/psr: Program Panel Replay CONFIG3 using AS SDP transmission time
Quoted 34 lines · Ville Syrjälä
Quoted 24 lines · Ankit Nautiyal
Panel Replay requires the AS SDP transmission time to be written into
PANEL_REPLAY_CONFIG3. This field was previously not programmed.Use the AS SDP transmission-time helper to populate CONFIG3.
Signed-off-by Ankit Nautiyal <[email protected]>--- drivers/gpu/drm/i915/display/intel_psr.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/display/intel_psr.c +1
-1@@ -783,7 +783,7 @@ static void _panel_replay_enable_sink(struct intel_dp *intel_dp, const struct intel_crtc_state *crtc_state) {struct intel_display *display =to_intel_display (intel_dp); -u8 panel_replay_config[2 ]; +u8 panel_replay_config[3 ];int ret; panel_replay_config[0] = DP_PANEL_REPLAY_ENABLE |drivers/gpu/drm/i915/display/intel_psr.c static void _panel_replay_enable_sink(struct intel_dp *intel_dp, · line 795
Quoted 4 lines
drivers/gpu/drm/i915/display/intel_psr.c +1
-0@@ -792,6 +792,7 @@ static void _panel_replay_enable_sink(struct intel_dp *intel_dp,DP_PANEL_REPLAY_RFB_STORAGE_ERROR_EN |DP_PANEL_REPLAY_ACTIVE_FRAME_CRC_ERROR_EN ; panel_replay_config[1 ] =DP_PANEL_REPLAY_CRC_VERIFICATION ; + panel_replay_config[2 ] =intel_dp_as_sdp_transmission_time ();
PANEL_REPLAY_CONFIG30x11a
...PANEL_REPLAY_CONFIG10x1b0PANEL_REPLAY_CONFIG20x1b1
Quoted 4 lines
So apparently we can't do the burst write for all three :/
Looks like
0x1b2is not used for anything so don't really understand why it wasn't added there. Oh well.
Oops! My bad. Thanks for catching this blunder.
I would also move the definition of PANEL_REPLAY_CONFIG3 above the PANEL_REPLAY_CONFIG.
I guess I didn’t pay any attention on the offset at all, and assumed this would follow PANEL_REPLAY_CONFIG2 :(
Will be careful and will not repeat this again.
Thanks,
Ankit
Quoted 6 lines
Quoted 6 lines
drivers/gpu/drm/i915/display/intel_psr.c +0
-0if (crtc_state->has_sel_update) panel_replay_config[0 ] |=DP_PANEL_REPLAY_SU_ENABLE ;Signature · 1 line
2.45.2
Re: [PATCH 15/19] drm/i915/psr: Program Panel Replay CONFIG3 using AS SDP transmission time
Quoted 42 lines · Ankit K
Quoted 34 lines · Ville Syrjälä
Quoted 24 lines · Ankit Nautiyal
Panel Replay requires the AS SDP transmission time to be written into
PANEL_REPLAY_CONFIG3. This field was previously not programmed.Use the AS SDP transmission-time helper to populate CONFIG3.
Signed-off-by Ankit Nautiyal <[email protected]>--- drivers/gpu/drm/i915/display/intel_psr.c | 3 ++- 1 file changed, 2 insertions(+), 1 deletion(-)drivers/gpu/drm/i915/display/intel_psr.c +1
-1@@ -783,7 +783,7 @@ static void _panel_replay_enable_sink(struct intel_dp *intel_dp, const struct intel_crtc_state *crtc_state) {struct intel_display *display =to_intel_display (intel_dp); -u8 panel_replay_config[2 ]; +u8 panel_replay_config[3 ];int ret; panel_replay_config[0] = DP_PANEL_REPLAY_ENABLE |drivers/gpu/drm/i915/display/intel_psr.c static void _panel_replay_enable_sink(struct intel_dp *intel_dp, · line 795
Quoted 4 lines
drivers/gpu/drm/i915/display/intel_psr.c +1
-0@@ -792,6 +792,7 @@ static void _panel_replay_enable_sink(struct intel_dp *intel_dp,DP_PANEL_REPLAY_RFB_STORAGE_ERROR_EN |DP_PANEL_REPLAY_ACTIVE_FRAME_CRC_ERROR_EN ; panel_replay_config[1 ] =DP_PANEL_REPLAY_CRC_VERIFICATION ; + panel_replay_config[2 ] =intel_dp_as_sdp_transmission_time ();
PANEL_REPLAY_CONFIG30x11a
...PANEL_REPLAY_CONFIG10x1b0PANEL_REPLAY_CONFIG20x1b1Quoted 4 lines
So apparently we can't do the burst write for all three :/
Looks like
0x1b2is not used for anything so don't really understand why it wasn't added there. Oh well.
Quoted 7 lines
Oops! My bad. Thanks for catching this blunder.
I would also move the definition of
PANEL_REPLAY_CONFIG3above thePANEL_REPLAY_CONFIG.I guess I didn’t pay any attention on the offset at all, and assumed this would follow
PANEL_REPLAY_CONFIG2:(
Yeah, I did the same mistake when reading the previous version and suggesting the burst write. But at least we can still do the burst write for PANEL_REPLAY_CONFIG1+PANEL_REPLAY_CONFIG2, so my suggestion wasn't entirely wrong :)
Quoted 13 lines
Will be careful and will not repeat this again.
Thanks,
AnkitQuoted 6 lines
Quoted 6 lines
drivers/gpu/drm/i915/display/intel_psr.c +0
-0if (crtc_state->has_sel_update) panel_replay_config[0 ] |=DP_PANEL_REPLAY_SU_ENABLE ;Signature · 1 line
2.45.2
Signature · 2 lines
Ville Syrjälä Intel
PATCH 16/19 drm/i915/dp: Set relevant Downspread Ctrl DPCD bits for PR + Auxless ALPM
In reply to Ankit NautiyalTo support Panel Replay with Auxless-ALPM, the source must transmit Adaptive-Sync SDPs for video timing synchronization while PR is active. As per the DP spec v2.1, this requires setting DPCD 0x0107[6] (FIXED_VTOTAL_AS_SDP_EN_IN_PR_ACTIVE). This applies whether VRR is enabled (AVT/FAVT) or fixed-timing mode is used.
--- drivers/gpu/drm/i915/display/intel_dp_link_training.c | 10 ++++++++-- drivers/gpu/drm/i915/display/intel_dp_link_training.h | 3 ++- drivers/gpu/drm/i915/display/intel_dp_mst.c | 2 +- 3 files changed, 11 insertions(+), 4 deletions(-)
drivers/gpu/drm/i915/display/intel_dp_link_training.c +8 -2
@@ -27,6 +27,7 @@#include <drm/display/drm_dp_helper.h> #include <drm/drm_print.h> +#include "intel_alpm.h" #include "intel_display_core.h" #include "intel_display_jiffies.h" #include "intel_display_types.h"
@@ -710,11 +711,14 @@ static bool intel_dp_link_max_vswing_reached(struct intel_dp *intel_dp,return true; } -void intel_dp_link_training_set_mode (struct intel_dp *intel_dp,int link_rate,bool is_vrr) +void intel_dp_link_training_set_mode (struct intel_dp *intel_dp,int link_rate, +bool is_vrr, +bool is_pr_with_link_off) {u8 link_config[2 ]; link_config[0 ] = is_vrr ?DP_MSA_TIMING_PAR_IGNORE_EN :0 ; + link_config[0 ] |= is_pr_with_link_off ?DP_FIXED_VTOTAL_AS_SDP_EN_IN_PR_ACTIVE :0 ; link_config[1 ] =drm_dp_is_uhbr_rate (link_rate) ?DP_SET_ANSI_128B132B :DP_SET_ANSI_8B10B ;drm_dp_dpcd_write (&intel_dp->aux,DP_DOWNSPREAD_CTRL , link_config,2 );
@@ -737,7 +741,9 @@ static void intel_dp_update_downspread_ctrl(struct intel_dp *intel_dp,* especially on the first real commit when clearing the inherited flag. */ intel_dp_link_training_set_mode (intel_dp, - crtc_state->port_clock, crtc_state->vrr.in_range); + crtc_state->port_clock, + crtc_state->vrr.in_range, +intel_alpm_is_alpm_aux_less (intel_dp, crtc_state)); } void intel_dp_link_training_set_bw(struct intel_dp *intel_dp,
drivers/gpu/drm/i915/display/intel_dp_link_training.h +2 -1
@@ -18,7 +18,8 @@ int intel_dp_init_lttpr_and_dprx_caps(struct intel_dp *intel_dp);bool intel_dp_lttpr_transparent_mode_enabled (struct intel_dp *intel_dp);void intel_dp_link_training_set_mode (struct intel_dp *intel_dp, -int link_rate,bool is_vrr); +int link_rate,bool is_vrr, +bool is_pr_with_link_off);void intel_dp_link_training_set_bw (struct intel_dp *intel_dp,int link_bw,int rate_select,int lane_count,bool enhanced_framing);
drivers/gpu/drm/i915/display/intel_dp_mst.c +1 -1
@@ -2142,7 +2142,7 @@ void intel_dp_mst_prepare_probe(struct intel_dp *intel_dp)intel_dp_compute_rate (intel_dp, link_rate, &link_bw, &rate_select); -intel_dp_link_training_set_mode (intel_dp, link_rate, false); +intel_dp_link_training_set_mode (intel_dp, link_rate, false, false);intel_dp_link_training_set_bw (intel_dp, link_bw, rate_select, lane_count,drm_dp_enhanced_frame_cap (intel_dp->dpcd));
Signature · 1 line
2.45.2
Re: [PATCH 16/19] drm/i915/dp: Set relevant Downspread Ctrl DPCD bits for PR + Auxless ALPM
Quoted 29 lines · Ankit Nautiyal
To support Panel Replay with Auxless-ALPM, the source must transmit Adaptive-Sync SDPs for video timing synchronization while PR is active. As per the DP spec v2.1, this requires setting DPCD 0x0107[6] (
FIXED_VTOTAL_AS_SDP_EN_IN_PR_ACTIVE). This applies whether VRR is enabled (AVT/FAVT) or fixed-timing mode is used.Signed-off-by Ankit Nautiyal <[email protected]>--- drivers/gpu/drm/i915/display/intel_dp_link_training.c | 10 ++++++++-- drivers/gpu/drm/i915/display/intel_dp_link_training.h | 3 ++- drivers/gpu/drm/i915/display/intel_dp_mst.c | 2 +- 3 files changed, 11 insertions(+), 4 deletions(-)drivers/gpu/drm/i915/display/intel_dp_link_training.c +1
-0@@ -27,6 +27,7 @@#include <drm/display/drm_dp_helper.h> #include <drm/drm_print.h> +#include "intel_alpm.h" #include "intel_display_core.h" #include "intel_display_jiffies.h" #include "intel_display_types.h" @@ -710,11 +711,14 @@ static bool intel_dp_link_max_vswing_reached(struct intel_dp *intel_dp,return true; }
drivers/gpu/drm/i915/display/intel_dp_link_training.c static bool intel_dp_link_max_vswing_reached(struct intel_dp *intel_dp, · line 722
Quoted 10 lines
drivers/gpu/drm/i915/display/intel_dp_link_training.c +4
-1-void intel_dp_link_training_set_mode (struct intel_dp *intel_dp,int link_rate,bool is_vrr) +void intel_dp_link_training_set_mode (struct intel_dp *intel_dp,int link_rate, +bool is_vrr, +bool is_pr_with_link_off) {u8 link_config[2 ]; link_config[0 ] = is_vrr ?DP_MSA_TIMING_PAR_IGNORE_EN :0 ; + link_config[0 ] |= is_pr_with_link_off ?DP_FIXED_VTOTAL_AS_SDP_EN_IN_PR_ACTIVE :0 ;
I think we should only set this if we are going to enable the AS SDP.
The bit seems to be perhaps a bit misnamed in the spec because you apparently you have to set it even if you suspend AS SDP transmission during PR active (when you have a sink with DP_PANEL_REPLAY_ASYNC_VIDEO_TIMING_NOT_SUPPORTED_IN_PR == 0). In that case it seems to just mean that the sink will grab the coasting vtotal from the last AS SDP transmitted prior to PR active.
Quoted 43 lines
drivers/gpu/drm/i915/display/intel_dp_link_training.c +0
-0link_config[1 ] =drm_dp_is_uhbr_rate (link_rate) ?DP_SET_ANSI_128B132B :DP_SET_ANSI_8B10B ;drivers/gpu/drm/i915/display/intel_dp_link_training.c +3
-1drm_dp_dpcd_write (&intel_dp->aux,DP_DOWNSPREAD_CTRL , link_config,2 );@@ -737,7 +741,9 @@ static void intel_dp_update_downspread_ctrl(struct intel_dp *intel_dp,* especially on the first real commit when clearing the inherited flag. */ intel_dp_link_training_set_mode (intel_dp, - crtc_state->port_clock, crtc_state->vrr.in_range); + crtc_state->port_clock, + crtc_state->vrr.in_range, +intel_alpm_is_alpm_aux_less (intel_dp, crtc_state)); } void intel_dp_link_training_set_bw(struct intel_dp *intel_dp,drivers/gpu/drm/i915/display/intel_dp_link_training.h +2
-1@@ -18,7 +18,8 @@ int intel_dp_init_lttpr_and_dprx_caps(struct intel_dp *intel_dp);bool intel_dp_lttpr_transparent_mode_enabled (struct intel_dp *intel_dp);void intel_dp_link_training_set_mode (struct intel_dp *intel_dp, -int link_rate,bool is_vrr); +int link_rate,bool is_vrr, +bool is_pr_with_link_off);void intel_dp_link_training_set_bw (struct intel_dp *intel_dp,int link_bw,int rate_select,int lane_count,bool enhanced_framing);drivers/gpu/drm/i915/display/intel_dp_mst.c +1
-1@@ -2142,7 +2142,7 @@ void intel_dp_mst_prepare_probe(struct intel_dp *intel_dp)intel_dp_compute_rate (intel_dp, link_rate, &link_bw, &rate_select); -intel_dp_link_training_set_mode (intel_dp, link_rate, false); +intel_dp_link_training_set_mode (intel_dp, link_rate, false, false);intel_dp_link_training_set_bw (intel_dp, link_bw, rate_select, lane_count,drm_dp_enhanced_frame_cap (intel_dp->dpcd));Signature · 1 line
2.45.2
Signature · 2 lines
Ville Syrjälä Intel
Re: [PATCH 16/19] drm/i915/dp: Set relevant Downspread Ctrl DPCD bits for PR + Auxless ALPM
Quoted 41 lines · Ville Syrjälä
Quoted 28 lines · Ankit Nautiyal
To support Panel Replay with Auxless-ALPM, the source must transmit Adaptive-Sync SDPs for video timing synchronization while PR is active. As per the DP spec v2.1, this requires setting DPCD 0x0107[6] (
FIXED_VTOTAL_AS_SDP_EN_IN_PR_ACTIVE). This applies whether VRR is enabled (AVT/FAVT) or fixed-timing mode is used.Signed-off-by Ankit Nautiyal <[email protected]>--- drivers/gpu/drm/i915/display/intel_dp_link_training.c | 10 ++++++++-- drivers/gpu/drm/i915/display/intel_dp_link_training.h | 3 ++- drivers/gpu/drm/i915/display/intel_dp_mst.c | 2 +- 3 files changed, 11 insertions(+), 4 deletions(-)drivers/gpu/drm/i915/display/intel_dp_link_training.c +1
-0@@ -27,6 +27,7 @@#include <drm/display/drm_dp_helper.h> #include <drm/drm_print.h> +#include "intel_alpm.h" #include "intel_display_core.h" #include "intel_display_jiffies.h" #include "intel_display_types.h" @@ -710,11 +711,14 @@ static bool intel_dp_link_max_vswing_reached(struct intel_dp *intel_dp,return true; }drivers/gpu/drm/i915/display/intel_dp_link_training.c static bool intel_dp_link_max_vswing_reached(struct intel_dp *intel_dp, · line 721
Quoted 10 lines
drivers/gpu/drm/i915/display/intel_dp_link_training.c +4
-1-void intel_dp_link_training_set_mode (struct intel_dp *intel_dp,int link_rate,bool is_vrr) +void intel_dp_link_training_set_mode (struct intel_dp *intel_dp,int link_rate, +bool is_vrr, +bool is_pr_with_link_off) {u8 link_config[2 ]; link_config[0 ] = is_vrr ?DP_MSA_TIMING_PAR_IGNORE_EN :0 ; + link_config[0 ] |= is_pr_with_link_off ?DP_FIXED_VTOTAL_AS_SDP_EN_IN_PR_ACTIVE :0 ;I think we should only set this if we are going to enable the AS SDP.
Quoted 6 lines
The bit seems to be perhaps a bit misnamed in the spec because you apparently you have to set it even if you suspend AS SDP transmission during PR active (when you have a sink with
DP_PANEL_REPLAY_ASYNC_VIDEO_TIMING_NOT_SUPPORTED_IN_PR== 0). In that case it seems to just mean that the sink will grab the coasting vtotal from the last AS SDP transmitted prior to PR active.
Hmm. Ok then I think will use:crtc_state->infoframe_enable & intel_hdmi_infoframe_enable(DP_SDP_ADAPTIVE_SYNC)
Also, I have not yet added fields for coasting vtotal. I am thinking to add that support and fill these for:pr_auxless_alpm && DP_PANEL_REPLAY_ASYNC_VIDEO_TIMING_NOT_SUPPORTED_IN_PR case.
Thanks,
Ankit
Quoted 44 lines
Quoted 44 lines
drivers/gpu/drm/i915/display/intel_dp_link_training.c +3
-1link_config[1 ] =drm_dp_is_uhbr_rate (link_rate) ?DP_SET_ANSI_128B132B :DP_SET_ANSI_8B10B ;drm_dp_dpcd_write (&intel_dp->aux,DP_DOWNSPREAD_CTRL , link_config,2 );@@ -737,7 +741,9 @@ static void intel_dp_update_downspread_ctrl(struct intel_dp *intel_dp,* especially on the first real commit when clearing the inherited flag. */ intel_dp_link_training_set_mode (intel_dp, - crtc_state->port_clock, crtc_state->vrr.in_range); + crtc_state->port_clock, + crtc_state->vrr.in_range, +intel_alpm_is_alpm_aux_less (intel_dp, crtc_state)); } void intel_dp_link_training_set_bw(struct intel_dp *intel_dp,drivers/gpu/drm/i915/display/intel_dp_link_training.h +2
-1@@ -18,7 +18,8 @@ int intel_dp_init_lttpr_and_dprx_caps(struct intel_dp *intel_dp);bool intel_dp_lttpr_transparent_mode_enabled (struct intel_dp *intel_dp);void intel_dp_link_training_set_mode (struct intel_dp *intel_dp, -int link_rate,bool is_vrr); +int link_rate,bool is_vrr, +bool is_pr_with_link_off);void intel_dp_link_training_set_bw (struct intel_dp *intel_dp,int link_bw,int rate_select,int lane_count,bool enhanced_framing);drivers/gpu/drm/i915/display/intel_dp_mst.c +1
-1@@ -2142,7 +2142,7 @@ void intel_dp_mst_prepare_probe(struct intel_dp *intel_dp)intel_dp_compute_rate (intel_dp, link_rate, &link_bw, &rate_select); -intel_dp_link_training_set_mode (intel_dp, link_rate, false); +intel_dp_link_training_set_mode (intel_dp, link_rate, false, false);intel_dp_link_training_set_bw (intel_dp, link_bw, rate_select, lane_count,drm_dp_enhanced_frame_cap (intel_dp->dpcd));Signature · 1 line
2.45.2
PATCH 17/19 drm/i915/dp: Program AS SDP DB[1:0] for PR with Link off
In reply to Ankit NautiyalFor Panel Replay with AUX-less ALPM (link-off PR), the source must send Adaptive-Sync SDP v2. Program DB[1:0] per DP spec v2.1:
- VRR AVT: 00b (variable VTotal)
- VRR FAVT: 10b/11b (TRR not reached/reached)
- Fixed timing with PR link-off (VRR off): 01b (AS disabled; VTotal fixed)
Also, drop the redundant target_rr assignment.
v2: Fix the else case. (Ville)
--- drivers/gpu/drm/i915/display/intel_dp.c | 5 +++-- 1 file changed, 3 insertions(+), 2 deletions(-)
drivers/gpu/drm/i915/display/intel_dp.c +3 -2
@@ -3161,9 +3161,10 @@ static void intel_dp_compute_as_sdp(struct intel_dp *intel_dp, as_sdp->mode =DP_AS_SDP_FAVT_TRR_REACHED ; as_sdp->target_rr =drm_mode_vrefresh (adjusted_mode); as_sdp->target_rr_divider = true; - }else { + }else if (crtc_state->vrr.enable) { as_sdp->mode =DP_AS_SDP_AVT_DYNAMIC_VTOTAL ; - as_sdp->target_rr =0 ; + }else { + as_sdp->mode =DP_AS_SDP_AVT_FIXED_VTOTAL ; } }
Signature · 1 line
2.45.2
PATCH 18/19 drm/i915/dp: Split AS SDP computation between compute_config and compute_config_late
In reply to Ankit NautiyalCurrently we enable AS SDP only when VRR is enabled. As we start using AS SDP for other features, this becomes a problem. The AS SDP configuration can change dynamically based on VRR, CMRR, PR, ALPM, etc. Since these features may be enabled or disabled after the initial configuration, the AS SDP parameters need to be computed later in the pipeline.
However, not all of the AS SDP logic can be moved to the late stage:
the VRR guardband optimization depends on knowing early whether AS SDP can be used. Without this, we would end up accounting for AS SDP on all platforms that support it, even for panels that do not support AS SDP. Therefore we set the infoframe enable bit for AS SDP during compute_config(), before the guardband is computed.
To handle these constraints, split the AS SDP programming into two phases:
- intel_dp_compute_as_sdp()
Runs during compute_config().
Sets only the infoframe enable bit so that the guardband logic can account for AS SDP requirements.
- intel_dp_as_sdp_compute_config_late()
Runs during compute_config_late().
Computes all remaining AS SDP fields based on the features that need it.
The late-stage computation is called from intel_dp_sdp_compute_config_late(), before computing the minimum guardband for SDPs.
This is a preparatory change. A subsequent patch will always enable AS SDP when the source and sink support it.
--- drivers/gpu/drm/i915/display/intel_dp.c | 67 ++++++++++++++++--------- 1 file changed, 44 insertions(+), 23 deletions(-)
drivers/gpu/drm/i915/display/intel_dp.c +44 -23
@@ -3142,30 +3142,17 @@ static bool intel_dp_can_use_as_sdp(struct intel_dp *intel_dp,static void intel_dp_compute_as_sdp (struct intel_dp *intel_dp,struct intel_crtc_state *crtc_state) { -struct drm_dp_as_sdp *as_sdp = &crtc_state->infoframes.as_sdp; -const struct drm_display_mode *adjusted_mode = - &crtc_state->hw.adjusted_mode; -if (!intel_dp_can_use_as_sdp (intel_dp, crtc_state))return ; +/* +* Only set the infoframes.enable flag here. +* The remaining AS SDP fields are programmed in the +* compute_config_late() phase. We need this flag early so that the +* VRR guardband calculation can properly account for AS SDP +* requirements. +*/ crtc_state->infoframes.enable |=intel_hdmi_infoframe_enable (DP_SDP_ADAPTIVE_SYNC ); - - as_sdp->sdp_type =DP_SDP_ADAPTIVE_SYNC ; - as_sdp->length =0x9 ; - as_sdp->duration_incr_ms =0 ; - as_sdp->revision =0x2 ; - as_sdp->vtotal =intel_vrr_vmin_vtotal (crtc_state); - -if (crtc_state->cmrr.enable) { - as_sdp->mode =DP_AS_SDP_FAVT_TRR_REACHED ; - as_sdp->target_rr =drm_mode_vrefresh (adjusted_mode); - as_sdp->target_rr_divider = true; - }else if (crtc_state->vrr.enable) { - as_sdp->mode =DP_AS_SDP_AVT_DYNAMIC_VTOTAL ; - }else { - as_sdp->mode =DP_AS_SDP_AVT_FIXED_VTOTAL ; - } } static void intel_dp_compute_vsc_sdp(struct intel_dp *intel_dp,
@@ -7370,11 +7357,45 @@ void intel_dp_mst_resume(struct intel_display *display) }static -int intel_dp_sdp_compute_config_late (struct intel_crtc_state *crtc_state) +void intel_dp_as_sdp_compute_config_late (struct intel_dp *intel_dp, +struct intel_crtc_state *crtc_state) +{ +struct drm_dp_as_sdp *as_sdp = &crtc_state->infoframes.as_sdp; +const struct drm_display_mode *adjusted_mode = + &crtc_state->hw.adjusted_mode; + +if ((crtc_state->infoframes.enable & +intel_hdmi_infoframe_enable (DP_SDP_ADAPTIVE_SYNC )) ==0 ) +return ; + + as_sdp->sdp_type =DP_SDP_ADAPTIVE_SYNC ; + as_sdp->length =0x9 ; + as_sdp->duration_incr_ms =0 ; + as_sdp->revision =0x2 ; + as_sdp->vtotal =intel_vrr_vmin_vtotal (crtc_state); + +if (crtc_state->cmrr.enable) { + as_sdp->mode =DP_AS_SDP_FAVT_TRR_REACHED ; + as_sdp->target_rr =drm_mode_vrefresh (adjusted_mode); + as_sdp->target_rr_divider = true; + }else if (crtc_state->vrr.enable) { + as_sdp->mode =DP_AS_SDP_AVT_DYNAMIC_VTOTAL ; + }else { + as_sdp->mode =DP_AS_SDP_AVT_FIXED_VTOTAL ; + } +} + +static +int intel_dp_sdp_compute_config_late (struct intel_dp *intel_dp, +struct intel_crtc_state *crtc_state) {struct intel_display *display =to_intel_display (crtc_state);int guardband =intel_crtc_vblank_length (crtc_state); -int min_sdp_guardband =intel_dp_sdp_min_guardband (crtc_state, false); +int min_sdp_guardband; + +intel_dp_as_sdp_compute_config_late (intel_dp, crtc_state); + + min_sdp_guardband =intel_dp_sdp_min_guardband (crtc_state, false);if (guardband < min_sdp_guardband) { drm_dbg_kms(display->drm, "guardband %d < min sdp guardband %d\n",
@@ -7394,7 +7415,7 @@ int intel_dp_compute_config_late(struct intel_encoder *encoder,intel_psr_compute_config_late (intel_dp, crtc_state); - ret =intel_dp_sdp_compute_config_late (crtc_state); + ret =intel_dp_sdp_compute_config_late (intel_dp, crtc_state);if (ret)return ret;
Signature · 1 line
2.45.2
Re: [PATCH 18/19] drm/i915/dp: Split AS SDP computation between compute_config and compute_config_late
Quoted 102 lines · Ankit Nautiyal
Currently we enable AS SDP only when VRR is enabled. As we start using AS SDP for other features, this becomes a problem. The AS SDP configuration can change dynamically based on VRR, CMRR, PR, ALPM, etc. Since these features may be enabled or disabled after the initial configuration, the AS SDP parameters need to be computed later in the pipeline.
However, not all of the AS SDP logic can be moved to the late stage:
the VRR guardband optimization depends on knowing early whether AS SDP can be used. Without this, we would end up accounting for AS SDP on all platforms that support it, even for panels that do not support AS SDP. Therefore we set the infoframe enable bit for AS SDP duringcompute_config(), before the guardband is computed.To handle these constraints, split the AS SDP programming into two phases:
-
intel_dp_compute_as_sdp()
Runs duringcompute_config().
Sets only the infoframe enable bit so that the guardband logic can account for AS SDP requirements.-
intel_dp_as_sdp_compute_config_late()
Runs duringcompute_config_late().
Computes all remaining AS SDP fields based on the features that need it.The late-stage computation is called from
intel_dp_sdp_compute_config_late(), before computing the minimum guardband for SDPs.This is a preparatory change. A subsequent patch will always enable AS SDP when the source and sink support it.
Signed-off-by Ankit Nautiyal <[email protected]>--- drivers/gpu/drm/i915/display/intel_dp.c | 67 ++++++++++++++++--------- 1 file changed, 44 insertions(+), 23 deletions(-)drivers/gpu/drm/i915/display/intel_dp.c +23
-21@@ -3142,30 +3142,17 @@ static bool intel_dp_can_use_as_sdp(struct intel_dp *intel_dp,static void intel_dp_compute_as_sdp (struct intel_dp *intel_dp,struct intel_crtc_state *crtc_state) { -struct drm_dp_as_sdp *as_sdp = &crtc_state->infoframes.as_sdp; -const struct drm_display_mode *adjusted_mode = - &crtc_state->hw.adjusted_mode; -if (!intel_dp_can_use_as_sdp (intel_dp, crtc_state))return ; +/* +* Only set the infoframes.enable flag here. +* The remaining AS SDP fields are programmed in the +* compute_config_late() phase. We need this flag early so that the +* VRR guardband calculation can properly account for AS SDP +* requirements. +*/ crtc_state->infoframes.enable |=intel_hdmi_infoframe_enable (DP_SDP_ADAPTIVE_SYNC ); - - as_sdp->sdp_type =DP_SDP_ADAPTIVE_SYNC ; - as_sdp->length =0x9 ; - as_sdp->duration_incr_ms =0 ; - as_sdp->revision =0x2 ; - as_sdp->vtotal =intel_vrr_vmin_vtotal (crtc_state); - -if (crtc_state->cmrr.enable) { - as_sdp->mode =DP_AS_SDP_FAVT_TRR_REACHED ; - as_sdp->target_rr =drm_mode_vrefresh (adjusted_mode); - as_sdp->target_rr_divider = true; - }else if (crtc_state->vrr.enable) { - as_sdp->mode =DP_AS_SDP_AVT_DYNAMIC_VTOTAL ; - }else { - as_sdp->mode =DP_AS_SDP_AVT_FIXED_VTOTAL ; - } } static void intel_dp_compute_vsc_sdp(struct intel_dp *intel_dp,@@ -7370,11 +7357,45 @@ void intel_dp_mst_resume(struct intel_display *display) }static -int intel_dp_sdp_compute_config_late (struct intel_crtc_state *crtc_state) +void intel_dp_as_sdp_compute_config_late (struct intel_dp *intel_dp, +struct intel_crtc_state *crtc_state) +{ +struct drm_dp_as_sdp *as_sdp = &crtc_state->infoframes.as_sdp; +const struct drm_display_mode *adjusted_mode = + &crtc_state->hw.adjusted_mode; + +if ((crtc_state->infoframes.enable & +intel_hdmi_infoframe_enable (DP_SDP_ADAPTIVE_SYNC )) ==0 ) +return ; + + as_sdp->sdp_type =DP_SDP_ADAPTIVE_SYNC ; + as_sdp->length =0x9 ; + as_sdp->duration_incr_ms =0 ; + as_sdp->revision =0x2 ; + as_sdp->vtotal =intel_vrr_vmin_vtotal (crtc_state);
drivers/gpu/drm/i915/display/intel_dp.c void intel_dp_mst_resume(struct intel_display *display) · line 7385
Quoted 10 lines
drivers/gpu/drm/i915/display/intel_dp.c +10
-0+ +if (crtc_state->cmrr.enable) { + as_sdp->mode =DP_AS_SDP_FAVT_TRR_REACHED ; + as_sdp->target_rr =drm_mode_vrefresh (adjusted_mode); + as_sdp->target_rr_divider = true; + }else if (crtc_state->vrr.enable) { + as_sdp->mode =DP_AS_SDP_AVT_DYNAMIC_VTOTAL ; + }else { + as_sdp->mode =DP_AS_SDP_AVT_FIXED_VTOTAL ; + }
Nothing in here right now depends on anything but intel_vrr_compute_config(). Was there something specific you will need to consult here that is computed later?
Quoted 28 lines
drivers/gpu/drm/i915/display/intel_dp.c +11
-2+} + +static +int intel_dp_sdp_compute_config_late (struct intel_dp *intel_dp, +struct intel_crtc_state *crtc_state) {struct intel_display *display =to_intel_display (crtc_state);int guardband =intel_crtc_vblank_length (crtc_state); -int min_sdp_guardband =intel_dp_sdp_min_guardband (crtc_state, false); +int min_sdp_guardband; + +intel_dp_as_sdp_compute_config_late (intel_dp, crtc_state); + + min_sdp_guardband =intel_dp_sdp_min_guardband (crtc_state, false);if (guardband < min_sdp_guardband) { drm_dbg_kms(display->drm, "guardband %d < min sdp guardband %d\n",@@ -7394,7 +7415,7 @@ int intel_dp_compute_config_late(struct intel_encoder *encoder,intel_psr_compute_config_late (intel_dp, crtc_state); - ret =intel_dp_sdp_compute_config_late (crtc_state); + ret =intel_dp_sdp_compute_config_late (intel_dp, crtc_state);if (ret)return ret;Signature · 1 line
2.45.2
Signature · 2 lines
Ville Syrjälä Intel
Re: [PATCH 18/19] drm/i915/dp: Split AS SDP computation between compute_config and compute_config_late
Quoted 108 lines · Ville Syrjälä
Quoted 107 lines · Ankit Nautiyal
Currently we enable AS SDP only when VRR is enabled. As we start using AS SDP for other features, this becomes a problem. The AS SDP configuration can change dynamically based on VRR, CMRR, PR, ALPM, etc. Since these features may be enabled or disabled after the initial configuration, the AS SDP parameters need to be computed later in the pipeline.
However, not all of the AS SDP logic can be moved to the late stage:
the VRR guardband optimization depends on knowing early whether AS SDP can be used. Without this, we would end up accounting for AS SDP on all platforms that support it, even for panels that do not support AS SDP. Therefore we set the infoframe enable bit for AS SDP duringcompute_config(), before the guardband is computed.To handle these constraints, split the AS SDP programming into two phases:
-
intel_dp_compute_as_sdp()
Runs duringcompute_config().
Sets only the infoframe enable bit so that the guardband logic can account for AS SDP requirements.-
intel_dp_as_sdp_compute_config_late()
Runs duringcompute_config_late().
Computes all remaining AS SDP fields based on the features that need it.The late-stage computation is called from
intel_dp_sdp_compute_config_late(), before computing the minimum guardband for SDPs.This is a preparatory change. A subsequent patch will always enable AS SDP when the source and sink support it.
Signed-off-by Ankit Nautiyal <[email protected]>--- drivers/gpu/drm/i915/display/intel_dp.c | 67 ++++++++++++++++--------- 1 file changed, 44 insertions(+), 23 deletions(-)drivers/gpu/drm/i915/display/intel_dp.c +28
-21@@ -3142,30 +3142,17 @@ static bool intel_dp_can_use_as_sdp(struct intel_dp *intel_dp,static void intel_dp_compute_as_sdp (struct intel_dp *intel_dp,struct intel_crtc_state *crtc_state) { -struct drm_dp_as_sdp *as_sdp = &crtc_state->infoframes.as_sdp; -const struct drm_display_mode *adjusted_mode = - &crtc_state->hw.adjusted_mode; -if (!intel_dp_can_use_as_sdp (intel_dp, crtc_state))return ; +/* +* Only set the infoframes.enable flag here. +* The remaining AS SDP fields are programmed in the +* compute_config_late() phase. We need this flag early so that the +* VRR guardband calculation can properly account for AS SDP +* requirements. +*/ crtc_state->infoframes.enable |=intel_hdmi_infoframe_enable (DP_SDP_ADAPTIVE_SYNC ); - - as_sdp->sdp_type =DP_SDP_ADAPTIVE_SYNC ; - as_sdp->length =0x9 ; - as_sdp->duration_incr_ms =0 ; - as_sdp->revision =0x2 ; - as_sdp->vtotal =intel_vrr_vmin_vtotal (crtc_state); - -if (crtc_state->cmrr.enable) { - as_sdp->mode =DP_AS_SDP_FAVT_TRR_REACHED ; - as_sdp->target_rr =drm_mode_vrefresh (adjusted_mode); - as_sdp->target_rr_divider = true; - }else if (crtc_state->vrr.enable) { - as_sdp->mode =DP_AS_SDP_AVT_DYNAMIC_VTOTAL ; - }else { - as_sdp->mode =DP_AS_SDP_AVT_FIXED_VTOTAL ; - } } static void intel_dp_compute_vsc_sdp(struct intel_dp *intel_dp,@@ -7370,11 +7357,45 @@ void intel_dp_mst_resume(struct intel_display *display) }static -int intel_dp_sdp_compute_config_late (struct intel_crtc_state *crtc_state) +void intel_dp_as_sdp_compute_config_late (struct intel_dp *intel_dp, +struct intel_crtc_state *crtc_state) +{ +struct drm_dp_as_sdp *as_sdp = &crtc_state->infoframes.as_sdp; +const struct drm_display_mode *adjusted_mode = + &crtc_state->hw.adjusted_mode; + +if ((crtc_state->infoframes.enable & +intel_hdmi_infoframe_enable (DP_SDP_ADAPTIVE_SYNC )) ==0 ) +return ; + + as_sdp->sdp_type =DP_SDP_ADAPTIVE_SYNC ; + as_sdp->length =0x9 ; + as_sdp->duration_incr_ms =0 ; + as_sdp->revision =0x2 ; + as_sdp->vtotal =intel_vrr_vmin_vtotal (crtc_state); + +if (crtc_state->cmrr.enable) { + as_sdp->mode =DP_AS_SDP_FAVT_TRR_REACHED ; + as_sdp->target_rr =drm_mode_vrefresh (adjusted_mode); + as_sdp->target_rr_divider = true;
Quoted 8 lines
drivers/gpu/drm/i915/display/intel_dp.c void intel_dp_mst_resume(struct intel_display *display) · line 7385
Quoted 5 lines
drivers/gpu/drm/i915/display/intel_dp.c +5
-0+ }else if (crtc_state->vrr.enable) { + as_sdp->mode =DP_AS_SDP_AVT_DYNAMIC_VTOTAL ; + }else { + as_sdp->mode =DP_AS_SDP_AVT_FIXED_VTOTAL ; + }Nothing in here right now depends on anything but
intel_vrr_compute_config(). Was there something specific you will need to consult here that is computed later?
This was required when I was trying to send AS SDP revision 1 based on
PR link ON requirement. Now that it has been nuked so we do not need this change yet.
However, when we need to fill coasting Vtotal for Panel replay active case, it will need panel replay stuff that is computed late.
So I guess we will need to compute this during ..compute_config_late().
Thanks,
Ankit
Quoted 29 lines
Quoted 29 lines
drivers/gpu/drm/i915/display/intel_dp.c +11
-2+} + +static +int intel_dp_sdp_compute_config_late (struct intel_dp *intel_dp, +struct intel_crtc_state *crtc_state) {struct intel_display *display =to_intel_display (crtc_state);int guardband =intel_crtc_vblank_length (crtc_state); -int min_sdp_guardband =intel_dp_sdp_min_guardband (crtc_state, false); +int min_sdp_guardband; + +intel_dp_as_sdp_compute_config_late (intel_dp, crtc_state); + + min_sdp_guardband =intel_dp_sdp_min_guardband (crtc_state, false);if (guardband < min_sdp_guardband) { drm_dbg_kms(display->drm, "guardband %d < min sdp guardband %d\n",@@ -7394,7 +7415,7 @@ int intel_dp_compute_config_late(struct intel_encoder *encoder,intel_psr_compute_config_late (intel_dp, crtc_state); - ret =intel_dp_sdp_compute_config_late (crtc_state); + ret =intel_dp_sdp_compute_config_late (intel_dp, crtc_state);if (ret)return ret;Signature · 1 line
2.45.2
PATCH 19/19 drm/i915/dp: Always enable AS SDP if supported by source + sink
In reply to Ankit NautiyalCurrently AS SDP is only configured when VRR is enabled. However, other use cases like CMRR, Panel Replay, etc. also send information to the sink via AS SDPs.
With optimized guardband, we also need to account for wakeup time and other relevant details that depend on the AS SDP position whenever AS SDP is enabled. If a feature enabling AS SDP gets turned on later (after modeset), the guardband might not be sufficient and may need to increase, triggering a full modeset.
To avoid this, always send AS SDP whenever the source and sink both support it.
--- drivers/gpu/drm/i915/display/intel_dp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
drivers/gpu/drm/i915/display/intel_dp.c +1 -1
@@ -3136,7 +3136,7 @@ static bool intel_dp_can_use_as_sdp(struct intel_dp *intel_dp,if (drm_dp_is_branch (intel_dp->dpcd))return false; -return crtc_state->vrr.enable; +return true; } static void intel_dp_compute_as_sdp(struct intel_dp *intel_dp,
Signature · 1 line
2.45.2
Re: [PATCH 19/19] drm/i915/dp: Always enable AS SDP if supported by source + sink
Quoted 23 lines · Ankit Nautiyal
Currently AS SDP is only configured when VRR is enabled. However, other use cases like CMRR, Panel Replay, etc. also send information to the sink via AS SDPs.
With optimized guardband, we also need to account for wakeup time and other relevant details that depend on the AS SDP position whenever AS SDP is enabled. If a feature enabling AS SDP gets turned on later (after modeset), the guardband might not be sufficient and may need to increase, triggering a full modeset.
To avoid this, always send AS SDP whenever the source and sink both support it.
Signed-off-by Ankit Nautiyal <[email protected]>--- drivers/gpu/drm/i915/display/intel_dp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/gpu/drm/i915/display/intel_dp.c +0
-0
drivers/gpu/drm/i915/display/intel_dp.c static bool intel_dp_can_use_as_sdp(struct intel_dp *intel_dp, · line 3139
Quoted 5 lines
drivers/gpu/drm/i915/display/intel_dp.c +1
-1@@ -3136,7 +3136,7 @@ static bool intel_dp_can_use_as_sdp(struct intel_dp *intel_dp,if (drm_dp_is_branch (intel_dp->dpcd))return false; -return crtc_state->vrr.enable; +return true;
I think what we actually want is something like
...
if (pr_auxless_alpm && DP_PANEL_REPLAY_ASYNC_VIDEO_TIMING_NOT_SUPPORTED_IN_PR) return true; return intel_vrr_possible(); }
That way non-VRR PR panels that don't need the AS SDP to maintain the synchronization can avoid the AS SDP, and thus potentially use a smaller guardband.
Quoted 5 lines
drivers/gpu/drm/i915/display/intel_dp.c +0
-0} static void intel_dp_compute_as_sdp(struct intel_dp *intel_dp,Signature · 1 line
2.45.2
Signature · 2 lines
Ville Syrjälä Intel
Re: [PATCH 19/19] drm/i915/dp: Always enable AS SDP if supported by source + sink
Quoted 38 lines · Ville Syrjälä
Quoted 23 lines · Ankit Nautiyal
Currently AS SDP is only configured when VRR is enabled. However, other use cases like CMRR, Panel Replay, etc. also send information to the sink via AS SDPs.
With optimized guardband, we also need to account for wakeup time and other relevant details that depend on the AS SDP position whenever AS SDP is enabled. If a feature enabling AS SDP gets turned on later (after modeset), the guardband might not be sufficient and may need to increase, triggering a full modeset.
To avoid this, always send AS SDP whenever the source and sink both support it.
Signed-off-by Ankit Nautiyal <[email protected]>--- drivers/gpu/drm/i915/display/intel_dp.c | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)drivers/gpu/drm/i915/display/intel_dp.c +0
-0drivers/gpu/drm/i915/display/intel_dp.c static bool intel_dp_can_use_as_sdp(struct intel_dp *intel_dp, · line 3139
Quoted 5 lines
drivers/gpu/drm/i915/display/intel_dp.c +1
-1@@ -3136,7 +3136,7 @@ static bool intel_dp_can_use_as_sdp(struct intel_dp *intel_dp,if (drm_dp_is_branch (intel_dp->dpcd))return false; -return crtc_state->vrr.enable; +return true;I think what we actually want is something like
...
if (pr_auxless_alpm && DP_PANEL_REPLAY_ASYNC_VIDEO_TIMING_NOT_SUPPORTED_IN_PR) return true; return intel_vrr_possible(); }
Quoted 3 lines
That way non-VRR PR panels that don't need the AS SDP to maintain the synchronization can avoid the AS SDP, and thus potentially use a smaller guardband.
Hmm.. makes sense. I will change this as suggested.
Thanks,
Ankit
Quoted 5 lines
Quoted 5 lines
drivers/gpu/drm/i915/display/intel_dp.c +0
-0} static void intel_dp_compute_as_sdp(struct intel_dp *intel_dp,Signature · 1 line
2.45.2