Skip to contentSkip to conversation

ARM: imx: imx8m: Introduce and use UART_BASE_ADDR(n)

PATCH In review Marek Vasut 4 participants 17 messages Apr 24, 2022 – May 20, 2022

Subsystems (2)
lore
Share & tools
lore
#0 lore raw

PATCH 1/4 ARM: imx: imx8m: Introduce and use UART_BASE_ADDR(n)

Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base address. Convert all board configurations to this new macro. This is the first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a clean up, no functional change.

The new macro contains compile-time test to verify N is in suitable range. The test works such that it multiplies constant N by constant double-negation of size of a non-empty structure, i.e. it multiplies constant N by constant 1 in each successful compilation case.

The non-empty structure may contain C11 _Static_assert(), make use of this and place the kernel variant of static assert in there, so that it performs the compile-time check for N in the correct range. Note that it is not possible to directly use static_assert in compound statements, hence this convoluted construct.

Cc Fabio Estevam <[email protected]>
Cc Peng Fan <[email protected]>
Cc Stefano Babic <[email protected]>
---
 arch/arm/include/asm/arch-imx8m/imx-regs.h | 10 ++++++++++
 include/configs/imx8mm-cl-iot-gate.h       |  2 +-
 include/configs/imx8mm_beacon.h            |  2 +-
 include/configs/imx8mm_evk.h               |  2 +-
 include/configs/imx8mm_icore_mx8mm.h       |  2 +-
 include/configs/imx8mm_venice.h            |  2 +-
 include/configs/imx8mn_beacon.h            |  2 +-
 include/configs/imx8mn_evk.h               |  2 +-
 include/configs/imx8mn_var_som.h           |  2 +-
 include/configs/imx8mn_venice.h            |  2 +-
 include/configs/imx8mp_evk.h               |  2 +-
 include/configs/imx8mp_rsb3720.h           |  2 +-
 include/configs/imx8mq_cm.h                |  2 +-
 include/configs/imx8mq_evk.h               |  2 +-
 include/configs/imx8mq_phanbell.h          |  2 +-
 include/configs/kontron-sl-mx8mm.h         |  2 +-
 include/configs/kontron_pitx_imx8m.h       |  2 +-
 include/configs/phycore_imx8mm.h           |  2 +-
 include/configs/phycore_imx8mp.h           |  2 +-
 include/configs/pico-imx8mq.h              |  2 +-
 include/configs/verdin-imx8mm.h            |  2 +-
 include/configs/verdin-imx8mp.h            |  2 +-
 22 files changed, 31 insertions(+), 21 deletions(-)
arch/arm/include/asm/arch-imx8m/imx-regs.h +10 -0
index b2a8ad77ae1..1da75528d46 100644
@@ -48,6 +48,16 @@
 #ifdef CONFIG_IMX8MM
 #define USDHC3_BASE_ADDR	0x30B60000
 #endif
+#define UART_BASE_ADDR(n)	(			\
+	!!sizeof(struct {				\
+		static_assert((n) >= 1 && (n) <= 4);	\
+		int pad;				\
+		}) * (					\
+	(n) == 1 ? UART1_BASE_ADDR :			\
+	(n) == 2 ? UART2_BASE_ADDR :			\
+	(n) == 3 ? UART3_BASE_ADDR :			\
+	UART4_BASE_ADDR)				\
+	)
 
 #define TZASC_BASE_ADDR		0x32F80000
 
include/configs/imx8mm-cl-iot-gate.h +1 -1
index c20c32b6951..60746588b73 100644
@@ -145,7 +145,7 @@
 #define PHYS_SDRAM			0x40000000
 #define PHYS_SDRAM_SIZE			0x80000000 /* 2GB DDR */
 
-#define CONFIG_MXC_UART_BASE		UART3_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(3)
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		2048
include/configs/imx8mm_beacon.h +1 -1
index 7c17f14964f..573ddaf2952 100644
@@ -91,7 +91,7 @@
 #define PHYS_SDRAM			0x40000000
 #define PHYS_SDRAM_SIZE		0x80000000 /* 2GB DDR */
 
-#define CONFIG_MXC_UART_BASE		UART2_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(2)
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		2048
include/configs/imx8mm_evk.h +1 -1
index 42b78485cfc..bd10406d79d 100644
@@ -68,7 +68,7 @@
 #define PHYS_SDRAM                      0x40000000
 #define PHYS_SDRAM_SIZE			0x80000000 /* 2GB DDR */
 
-#define CONFIG_MXC_UART_BASE		UART2_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(2)
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		2048
include/configs/imx8mm_icore_mx8mm.h +1 -1
index f521add5b04..b9b24a8c51d 100644
@@ -66,7 +66,7 @@
 #define CONFIG_SYS_BOOTM_LEN		SZ_256M
 
 /* UART */
-#define CONFIG_MXC_UART_BASE		UART2_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(2)
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		2048
include/configs/imx8mm_venice.h +1 -1
index 1b26e0280e1..f3dad256100 100644
@@ -102,7 +102,7 @@
 #define CONFIG_SYS_BOOTM_LEN		SZ_256M
 
 /* UART */
-#define CONFIG_MXC_UART_BASE		UART2_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(2)
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		SZ_2K
include/configs/imx8mn_beacon.h +1 -1
index 41ce3c1c8ce..79c6b1076ff 100644
@@ -107,7 +107,7 @@
 #define PHYS_SDRAM_SIZE		0x40000000 /* 1GB DDR */
 #endif
 
-#define CONFIG_MXC_UART_BASE		UART2_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(2)
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE              2048
include/configs/imx8mn_evk.h +1 -1
index 034132225c6..805ae2a7518 100644
@@ -75,7 +75,7 @@
 #define PHYS_SDRAM                      0x40000000
 #define PHYS_SDRAM_SIZE			0x80000000 /* 2GB DDR */
 
-#define CONFIG_MXC_UART_BASE		UART2_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(2)
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		2048
include/configs/imx8mn_var_som.h +1 -1
index 318289b76bc..00358892b28 100644
@@ -64,7 +64,7 @@
 #define PHYS_SDRAM			0x40000000
 #define PHYS_SDRAM_SIZE			SZ_1G /* 1GB DDR */
 
-#define CONFIG_MXC_UART_BASE		UART4_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(4)
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		SZ_2K
include/configs/imx8mn_venice.h +1 -1
index a4826779022..dcb5baf6eb4 100644
@@ -98,7 +98,7 @@
 #define CONFIG_SYS_BOOTM_LEN		SZ_256M
 
 /* UART */
-#define CONFIG_MXC_UART_BASE		UART2_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(2)
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		SZ_2K
include/configs/imx8mp_evk.h +1 -1
index cc8d65cb54e..908ed76f39e 100644
@@ -80,7 +80,7 @@
 #define PHYS_SDRAM_2			0x100000000
 #define PHYS_SDRAM_2_SIZE		0xC0000000	/* 3 GB */
 
-#define CONFIG_MXC_UART_BASE		UART2_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(2)
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		2048
include/configs/imx8mp_rsb3720.h +1 -1
index c5dd545471e..c0f2824fd4c 100644
@@ -169,7 +169,7 @@
 #define PHYS_SDRAM_2_SIZE		0x80000000	/* 2 GB */
 #endif
 
-#define CONFIG_MXC_UART_BASE		UART3_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(3)
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		2048
include/configs/imx8mq_cm.h +1 -1
index 989486aa6dc..6eecfc813a4 100644
@@ -71,7 +71,7 @@
 #define PHYS_SDRAM                      0x40000000
 #define PHYS_SDRAM_SIZE					0x40000000 /* 1 GB DDR */
 
-#define CONFIG_MXC_UART_BASE		UART1_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(1)
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		1024
include/configs/imx8mq_evk.h +1 -1
index f7929e5867e..8596d999257 100644
@@ -78,7 +78,7 @@
 #define PHYS_SDRAM                      0x40000000
 #define PHYS_SDRAM_SIZE			0xC0000000 /* 3GB DDR */
 
-#define CONFIG_MXC_UART_BASE		UART1_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(1)
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		1024
include/configs/imx8mq_phanbell.h +1 -1
index f6410114b76..9cf779b0752 100644
@@ -106,7 +106,7 @@
 #define PHYS_SDRAM                      0x40000000
 #define PHYS_SDRAM_SIZE			0x40000000 /* 1GB DDR */
 
-#define CONFIG_MXC_UART_BASE		UART1_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(1)
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		1024
include/configs/kontron-sl-mx8mm.h +1 -1
index 1b429f7dbe2..8b2a10dda1f 100644
@@ -28,7 +28,7 @@
 	(CONFIG_SYS_INIT_RAM_ADDR + CONFIG_SYS_INIT_SP_OFFSET)
 
 /* Board and environment settings */
-#define CONFIG_MXC_UART_BASE		UART3_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(3)
 #define CONFIG_HOSTNAME			"kontron-mx8mm"
 
 #ifdef CONFIG_USB_EHCI_HCD
include/configs/kontron_pitx_imx8m.h +1 -1
index e8e92920dcb..182ee590318 100644
@@ -84,7 +84,7 @@
 #define PHYS_SDRAM                      0x40000000
 #define PHYS_SDRAM_SIZE			0xC0000000 /* 3GB DDR */
 
-#define CONFIG_MXC_UART_BASE		UART3_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(3)
 
 #define CONFIG_SYS_FSL_USDHC_NUM	2
 #define CONFIG_SYS_FSL_ESDHC_ADDR       0
include/configs/phycore_imx8mm.h +1 -1
index 71f0c42ec0c..46fadd56106 100644
@@ -84,7 +84,7 @@
 #define PHYS_SDRAM_SIZE                 SZ_2G /* 2GB DDR */
 
 /* UART */
-#define CONFIG_MXC_UART_BASE		UART3_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(3)
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		SZ_2K
include/configs/phycore_imx8mp.h +1 -1
index 0c963b62b3b..eb92c423392 100644
@@ -84,7 +84,7 @@
 #define PHYS_SDRAM_SIZE			0x80000000
 
 /* UART */
-#define CONFIG_MXC_UART_BASE		UART1_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(1)
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		SZ_2K
include/configs/pico-imx8mq.h +1 -1
index 95845276e7b..567b06c4f5d 100644
@@ -85,7 +85,7 @@
 #define PHYS_SDRAM			0x40000000
 #define PHYS_SDRAM_SIZE			0x80000000	/* 2 GiB DDR */
 
-#define CONFIG_MXC_UART_BASE		UART1_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(1)
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		1024
include/configs/verdin-imx8mm.h +1 -1
index da3dc95f9ee..130a1ed54d1 100644
@@ -84,7 +84,7 @@
 #define PHYS_SDRAM_SIZE			SZ_2G /* 2GB DDR */
 
 /* UART */
-#define CONFIG_MXC_UART_BASE		UART1_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(1)
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		SZ_2K
include/configs/verdin-imx8mp.h +1 -1
index 7b7407752c1..33cfd3d2d73 100644
@@ -101,7 +101,7 @@
 #define PHYS_SDRAM_2_SIZE		(SZ_4G + SZ_1G)
 
 /* UART */
-#define CONFIG_MXC_UART_BASE		UART3_BASE_ADDR
+#define CONFIG_MXC_UART_BASE		UART_BASE_ADDR(3)
 
 /* Monitor Command Prompt */
 #define CONFIG_SYS_CBSIZE		SZ_2K
Signature · 1 line
2.35.1
#1 lore raw

PATCH 2/4 ARM: imx: imx27: Introduce and use UART_BASE_ADDR(n)

Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base address. Convert all board configurations to this new macro. This is the first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a clean up, no functional change.

The new macro contains compile-time test to verify N is in suitable range. The test works such that it multiplies constant N by constant double-negation of size of a non-empty structure, i.e. it multiplies constant N by constant 1 in each successful compilation case.

The non-empty structure may contain C11 _Static_assert(), make use of this and place the kernel variant of static assert in there, so that it performs the compile-time check for N in the correct range. Note that it is not possible to directly use static_assert in compound statements, hence this convoluted construct.

Cc Fabio Estevam <[email protected]>
Cc Peng Fan <[email protected]>
Cc Stefano Babic <[email protected]>
---
 arch/arm/include/asm/arch-mx27/imx-regs.h | 24 +++++++++++++++++------
 include/configs/imx27lite-common.h        |  2 +-
 2 files changed, 19 insertions(+), 7 deletions(-)
arch/arm/include/asm/arch-mx27/imx-regs.h +18 -6
index d39f6b03508..77794d7d03d 100644
@@ -179,16 +179,16 @@ struct fuse_bank0_regs {
 #define IMX_TIM2_BASE		(0x04000 + IMX_IO_BASE)
 #define IMX_TIM3_BASE		(0x05000 + IMX_IO_BASE)
 #define IMX_RTC_BASE		(0x07000 + IMX_IO_BASE)
-#define UART1_BASE		(0x0a000 + IMX_IO_BASE)
-#define UART2_BASE		(0x0b000 + IMX_IO_BASE)
-#define UART3_BASE		(0x0c000 + IMX_IO_BASE)
-#define UART4_BASE		(0x0d000 + IMX_IO_BASE)
+#define UART1_BASE_ADDR		(0x0a000 + IMX_IO_BASE)
+#define UART2_BASE_ADDR		(0x0b000 + IMX_IO_BASE)
+#define UART3_BASE_ADDR		(0x0c000 + IMX_IO_BASE)
+#define UART4_BASE_ADDR		(0x0d000 + IMX_IO_BASE)
 #define I2C1_BASE_ADDR		(0x12000 + IMX_IO_BASE)
 #define IMX_GPIO_BASE		(0x15000 + IMX_IO_BASE)
 #define IMX_TIM4_BASE		(0x19000 + IMX_IO_BASE)
 #define IMX_TIM5_BASE		(0x1a000 + IMX_IO_BASE)
-#define IMX_UART5_BASE		(0x1b000 + IMX_IO_BASE)
-#define IMX_UART6_BASE		(0x1c000 + IMX_IO_BASE)
+#define UART5_BASE_ADDR		(0x1b000 + IMX_IO_BASE)
+#define UART6_BASE_ADDR		(0x1c000 + IMX_IO_BASE)
 #define I2C2_BASE_ADDR		(0x1D000 + IMX_IO_BASE)
 #define IMX_TIM6_BASE		(0x1f000 + IMX_IO_BASE)
 #define IMX_AIPI2_BASE		(0x20000 + IMX_IO_BASE)
@@ -204,6 +204,18 @@ struct fuse_bank0_regs {
 
 #define NFC_BASE_ADDR		IMX_NFC_BASE
 
+#define UART_BASE_ADDR(n)	(			\
+	!!sizeof(struct {				\
+		static_assert((n) >= 1 && (n) <= 6);	\
+		int pad;				\
+		}) * (					\
+	(n) == 1 ? UART1_BASE_ADDR :			\
+	(n) == 2 ? UART2_BASE_ADDR :			\
+	(n) == 3 ? UART3_BASE_ADDR :			\
+	(n) == 4 ? UART4_BASE_ADDR :			\
+	(n) == 5 ? UART5_BASE_ADDR :			\
+	UART6_BASE_ADDR)				\
+	)
 
 /* FMCR System Control bit definition*/
 #define UART4_RXD_CTL	(1 << 25)
include/configs/imx27lite-common.h +1 -1
index bb53a33a542..6790053bb8d 100644
@@ -70,7 +70,7 @@
 /*
  * Serial Driver info
  */
-#define CONFIG_MXC_UART_BASE	UART1_BASE
+#define CONFIG_MXC_UART_BASE	UART_BASE_ADDR(1)
 
 /*
  * Flash & Environment
Signature · 1 line
2.35.1
#2 lore raw

PATCH 2/4 ARM: imx: imx27: Introduce and use UART_BASE_ADDR(n)

Quoted 13 lines

Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base address. Convert all board configurations to this new macro. This is the first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a clean up, no functional change.
The new macro contains compile-time test to verify N is in suitable range. The test works such that it multiplies constant N by constant double-negation of size of a non-empty structure, i.e. it multiplies constant N by constant 1 in each successful compilation case. The non-empty structure may contain C11 _Static_assert(), make use of this and place the kernel variant of static assert in there, so that it performs the compile-time check for N in the correct range. Note that it is not possible to directly use static_assert in compound statements, hence this convoluted construct.

Quoted 4 lines
Cc Fabio Estevam <[email protected]>
Cc Peng Fan <[email protected]>
Cc Stefano Babic <[email protected]>

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
#3 lore raw

PATCH 3/4 ARM: imx: imx31: Introduce and use UART_BASE_ADDR(n)

In reply to Marek Vasut

Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base address. Convert all board configurations to this new macro. This is the first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a clean up, no functional change.

The new macro contains compile-time test to verify N is in suitable range. The test works such that it multiplies constant N by constant double-negation of size of a non-empty structure, i.e. it multiplies constant N by constant 1 in each successful compilation case.

The non-empty structure may contain C11 _Static_assert(), make use of this and place the kernel variant of static assert in there, so that it performs the compile-time check for N in the correct range. Note that it is not possible to directly use static_assert in compound statements, hence this convoluted construct.

Cc Fabio Estevam <[email protected]>
Cc Peng Fan <[email protected]>
Cc Stefano Babic <[email protected]>
---
 arch/arm/include/asm/arch-mx31/imx-regs.h | 12 ++++++++++++
 1 file changed, 12 insertions(+)
arch/arm/include/asm/arch-mx31/imx-regs.h +12 -0
index 566db549ec6..d5c0ed8e6c2 100644
@@ -598,6 +598,18 @@ struct esdc_regs {
 #define UART4_BASE	0x43FB0000
 #define UART5_BASE	0x43FB4000
 
+#define UART_BASE_ADDR(n)	(			\
+	!!sizeof(struct {				\
+		static_assert((n) >= 1 && (n) <= 5);	\
+		int pad;				\
+		}) * (					\
+	(n) == 1 ? UART1_BASE :				\
+	(n) == 2 ? UART2_BASE :				\
+	(n) == 3 ? UART3_BASE :				\
+	(n) == 4 ? UART4_BASE :				\
+	UART5_BASE_ADDR)				\
+	)
+
 #define I2C1_BASE_ADDR          0x43f80000
 #define I2C1_CLK_OFFSET		26
 #define I2C2_BASE_ADDR          0x43F98000
Signature · 1 line
2.35.1
#4 lore raw

PATCH 3/4 ARM: imx: imx31: Introduce and use UART_BASE_ADDR(n)

Quoted 13 lines

Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base address. Convert all board configurations to this new macro. This is the first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a clean up, no functional change.
The new macro contains compile-time test to verify N is in suitable range. The test works such that it multiplies constant N by constant double-negation of size of a non-empty structure, i.e. it multiplies constant N by constant 1 in each successful compilation case. The non-empty structure may contain C11 _Static_assert(), make use of this and place the kernel variant of static assert in there, so that it performs the compile-time check for N in the correct range. Note that it is not possible to directly use static_assert in compound statements, hence this convoluted construct.

Quoted 4 lines
Cc Fabio Estevam <[email protected]>
Cc Peng Fan <[email protected]>
Cc Stefano Babic <[email protected]>

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
#5 lore raw

PATCH 4/4 ARM: imx: imx5: Introduce and use UART_BASE_ADDR(n)

In reply to Marek Vasut

Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base address. Convert all board configurations to this new macro. This is the first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a clean up, no functional change.

The new macro contains compile-time test to verify N is in suitable range. The test works such that it multiplies constant N by constant double-negation of size of a non-empty structure, i.e. it multiplies constant N by constant 1 in each successful compilation case.

The non-empty structure may contain C11 _Static_assert(), make use of this and place the kernel variant of static assert in there, so that it performs the compile-time check for N in the correct range. Note that it is not possible to directly use static_assert in compound statements, hence this convoluted construct.

Cc Fabio Estevam <[email protected]>
Cc Peng Fan <[email protected]>
Cc Stefano Babic <[email protected]>
---
 arch/arm/include/asm/arch-mx5/imx-regs.h | 23 +++++++++++++++++++++++
 include/configs/mx51evk.h                |  2 +-
 include/configs/mx53cx9020.h             |  2 +-
 include/configs/mx53loco.h               |  2 +-
 include/configs/usbarmory.h              |  2 +-
 5 files changed, 27 insertions(+), 4 deletions(-)
arch/arm/include/asm/arch-mx5/imx-regs.h +23 -0
index f763749b03c..856bc07e8ae 100644
@@ -125,6 +125,29 @@
 
 #if defined(CONFIG_MX53)
 #define UART5_BASE_ADDR         (AIPS2_BASE_ADDR + 0x00090000)
+
+#define UART_BASE_ADDR(n)	(			\
+	!!sizeof(struct {				\
+		static_assert((n) >= 1 && (n) <= 5);	\
+		int pad;				\
+		}) * (					\
+	(n) == 1 ? UART1_BASE :				\
+	(n) == 2 ? UART2_BASE :				\
+	(n) == 3 ? UART3_BASE :				\
+	(n) == 4 ? UART4_BASE_ADDR :			\
+	UART5_BASE_ADDR)				\
+	)
+#else	/* i.MX51 */
+#define UART_BASE_ADDR(n)	(			\
+	!!sizeof(struct {				\
+		static_assert((n) >= 1 && (n) <= 4);	\
+		int pad;				\
+		}) * (					\
+	(n) == 1 ? UART1_BASE :				\
+	(n) == 2 ? UART2_BASE :				\
+	(n) == 3 ? UART3_BASE :				\
+	UART4_BASE_ADDR)				\
+	)
 #endif
 
 /*
include/configs/mx51evk.h +1 -1
index ccfe292f6c6..814202e48d0 100644
@@ -19,7 +19,7 @@
  */
 #define CONFIG_FSL_IIM
 
-#define CONFIG_MXC_UART_BASE	UART1_BASE
+#define CONFIG_MXC_UART_BASE	UART_BASE_ADDR(1)
 
 /* PMIC Controller */
 #define CONFIG_POWER_SPI
include/configs/mx53cx9020.h +1 -1
index fafc5f1adcb..9f2259d2981 100644
@@ -14,7 +14,7 @@
 
 #include <asm/arch/imx-regs.h>
 
-#define CONFIG_MXC_UART_BASE UART2_BASE
+#define CONFIG_MXC_UART_BASE UART_BASE_ADDR(2)
 
 #define CONFIG_FPGA_COUNT 1
 
include/configs/mx53loco.h +1 -1
index 8b9f0a29017..9851f64ee9f 100644
@@ -11,7 +11,7 @@
 
 #include <asm/arch/imx-regs.h>
 
-#define CONFIG_MXC_UART_BASE	UART1_BASE
+#define CONFIG_MXC_UART_BASE	UART_BASE_ADDR(1)
 
 /* MMC Configs */
 #define CONFIG_SYS_FSL_ESDHC_ADDR	0
include/configs/usbarmory.h +1 -1
index 0faa656bc63..98b289e7ff1 100644
@@ -18,7 +18,7 @@
 #define CONFIG_SYS_CBSIZE	512
 
 /* UART */
-#define CONFIG_MXC_UART_BASE	UART1_BASE
+#define CONFIG_MXC_UART_BASE	UART_BASE_ADDR(1)
 
 /* SD/MMC */
 #define CONFIG_SYS_FSL_ESDHC_ADDR	0
Signature · 1 line
2.35.1
#6 lore raw

Re: [PATCH 4/4] ARM: imx: imx5: Introduce and use UART_BASE_ADDR(n)

Hi Marek,

Quoted 16 lines · Marek Vasut

Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base address. Convert all board configurations to this new macro. This is the first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a clean up, no functional change.

The new macro contains compile-time test to verify N is in suitable range. The test works such that it multiplies constant N by constant double-negation of size of a non-empty structure, i.e. it multiplies constant N by constant 1 in each successful compilation case.

The non-empty structure may contain C11 _Static_assert(), make use of this and place the kernel variant of static assert in there, so that it performs the compile-time check for N in the correct range. Note that it is not possible to directly use static_assert in compound statements, hence this convoluted construct.

Quoted 5 lines
Cc Fabio Estevam <[email protected]>
Cc Peng Fan <[email protected]>
Cc Stefano Babic <[email protected]>

---

I have not found the reason, but this breaks MX51:

https://source.denx.de/u-boot/custodians/u-boot-imx/-/jobs/436880

Regards,
Stefano

Quoted 93 lines
  arch/arm/include/asm/arch-mx5/imx-regs.h | 23 +++++++++++++++++++++++
  include/configs/mx51evk.h                |  2 +-
  include/configs/mx53cx9020.h             |  2 +-
  include/configs/mx53loco.h               |  2 +-
  include/configs/usbarmory.h              |  2 +-
  5 files changed, 27 insertions(+), 4 deletions(-)
arch/arm/include/asm/arch-mx5/imx-regs.h +23 -0
index f763749b03c..856bc07e8ae 100644
@@ -125,6 +125,29 @@
 
  #if defined(CONFIG_MX53)
  #define UART5_BASE_ADDR         (AIPS2_BASE_ADDR + 0x00090000)
+
+#define UART_BASE_ADDR(n)	(			\
+	!!sizeof(struct {				\
+		static_assert((n) >= 1 && (n) <= 5);	\
+		int pad;				\
+		}) * (					\
+	(n) == 1 ? UART1_BASE :				\
+	(n) == 2 ? UART2_BASE :				\
+	(n) == 3 ? UART3_BASE :				\
+	(n) == 4 ? UART4_BASE_ADDR :			\
+	UART5_BASE_ADDR)				\
+	)
+#else	/* i.MX51 */
+#define UART_BASE_ADDR(n)	(			\
+	!!sizeof(struct {				\
+		static_assert((n) >= 1 && (n) <= 4);	\
+		int pad;				\
+		}) * (					\
+	(n) == 1 ? UART1_BASE :				\
+	(n) == 2 ? UART2_BASE :				\
+	(n) == 3 ? UART3_BASE :				\
+	UART4_BASE_ADDR)				\
+	)
  #endif
 
  /*
include/configs/mx51evk.h +1 -1
index ccfe292f6c6..814202e48d0 100644
@@ -19,7 +19,7 @@
   */
  #define CONFIG_FSL_IIM
 
-#define CONFIG_MXC_UART_BASE	UART1_BASE
+#define CONFIG_MXC_UART_BASE	UART_BASE_ADDR(1)
 
  /* PMIC Controller */
  #define CONFIG_POWER_SPI
include/configs/mx53cx9020.h +1 -1
index fafc5f1adcb..9f2259d2981 100644
@@ -14,7 +14,7 @@
 
  #include <asm/arch/imx-regs.h>
 
-#define CONFIG_MXC_UART_BASE UART2_BASE
+#define CONFIG_MXC_UART_BASE UART_BASE_ADDR(2)
 
  #define CONFIG_FPGA_COUNT 1
 
include/configs/mx53loco.h +1 -1
index 8b9f0a29017..9851f64ee9f 100644
@@ -11,7 +11,7 @@
 
  #include <asm/arch/imx-regs.h>
 
-#define CONFIG_MXC_UART_BASE	UART1_BASE
+#define CONFIG_MXC_UART_BASE	UART_BASE_ADDR(1)
 
  /* MMC Configs */
  #define CONFIG_SYS_FSL_ESDHC_ADDR	0
include/configs/usbarmory.h +1 -1
index 0faa656bc63..98b289e7ff1 100644
@@ -18,7 +18,7 @@
  #define CONFIG_SYS_CBSIZE	512
 
  /* UART */
-#define CONFIG_MXC_UART_BASE	UART1_BASE
+#define CONFIG_MXC_UART_BASE	UART_BASE_ADDR(1)
 
  /* SD/MMC */
  #define CONFIG_SYS_FSL_ESDHC_ADDR	0
Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
#7 lore raw

Re: [PATCH 4/4] ARM: imx: imx5: Introduce and use UART_BASE_ADDR(n)

Quoted 19 lines · Stefano Babic

Hi Marek,

Quoted 16 lines · Marek Vasut

Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base address. Convert all board configurations to this new macro. This is the first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a clean up, no functional change.

The new macro contains compile-time test to verify N is in suitable range. The test works such that it multiplies constant N by constant double-negation of size of a non-empty structure, i.e. it multiplies constant N by constant 1 in each successful compilation case.

The non-empty structure may contain C11 _Static_assert(), make use of this and place the kernel variant of static assert in there, so that it performs the compile-time check for N in the correct range. Note that it is not possible to directly use static_assert in compound statements, hence this convoluted construct.

Quoted 7 lines
Quoted 5 lines
Cc Fabio Estevam <[email protected]>
Cc Peng Fan <[email protected]>
Cc Stefano Babic <[email protected]>

---

I have not found the reason, but this breaks MX51:

All this UART_BASE_ADDR stuff is postponed, just drop for now.

#8 lore raw

Re: [PATCH 4/4] ARM: imx: imx5: Introduce and use UART_BASE_ADDR(n)

Quoted 26 lines · Marek Vasut
Quoted 25 lines · Stefano Babic

Hi Marek,

Quoted 21 lines · Marek Vasut

Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base address. Convert all board configurations to this new macro. This is the first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a clean up, no functional change.

The new macro contains compile-time test to verify N is in suitable range. The test works such that it multiplies constant N by constant double-negation of size of a non-empty structure, i.e. it multiplies constant N by constant 1 in each successful compilation case.

The non-empty structure may contain C11 _Static_assert(), make use of this and place the kernel variant of static assert in there, so that it performs the compile-time check for N in the correct range. Note that it is not possible to directly use static_assert in compound statements, hence this convoluted construct.

Cc Fabio Estevam <[email protected]>
Cc Peng Fan <[email protected]>
Cc Stefano Babic <[email protected]>

---

Quoted 3 lines
Quoted 1 line

I have not found the reason, but this breaks MX51:

All this UART_BASE_ADDR stuff is postponed, just drop for now.

Ok, understood - I remove them.

Best regards,
Stefano

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
#9 lore raw

Re: [PATCH 4/4] ARM: imx: imx5: Introduce and use UART_BASE_ADDR(n)

Quoted 27 lines · Stefano Babic
Quoted 26 lines · Marek Vasut
Quoted 25 lines · Stefano Babic

Hi Marek,

Quoted 21 lines · Marek Vasut

Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base address. Convert all board configurations to this new macro. This is the first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a clean up, no functional change.

The new macro contains compile-time test to verify N is in suitable range. The test works such that it multiplies constant N by constant double-negation of size of a non-empty structure, i.e. it multiplies constant N by constant 1 in each successful compilation case.

The non-empty structure may contain C11 _Static_assert(), make use of this and place the kernel variant of static assert in there, so that it performs the compile-time check for N in the correct range. Note that it is not possible to directly use static_assert in compound statements, hence this convoluted construct.

Cc Fabio Estevam <[email protected]>
Cc Peng Fan <[email protected]>
Cc Stefano Babic <[email protected]>

---

Quoted 6 lines
Quoted 3 lines
Quoted 1 line

I have not found the reason, but this breaks MX51:

All this UART_BASE_ADDR stuff is postponed, just drop for now.

Ok, understood - I remove them.

Well, there is at least one patch depending on this:

http://patchwork.ozlabs.org/project/uboot/patch/[email protected]/

I will first try just to remove the i.MX5 patch, it seems to me that the MX51 is the only architecture that cannot be built.

Regards,
Stefano

Quoted 4 lines

Best regards,
Stefano

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================
#10 lore raw
In reply to Marek Vasut

Hi Marek,

Quoted 4 lines · Marek Vasut

Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base address. Convert all board configurations to this new macro. This is the first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a clean up, no functional change.

As DM_SERIAL is mandatory now, we should get rid of CONFIG_MXC_UART_BASE.

I would prefer a patch that removes CONFIG_MXC_UART_BASE instead.

Regards,

Fabio Estevam

#11 lore raw
Quoted 11 lines · Fabio Estevam

Hi Marek,

Quoted 4 lines · Marek Vasut

Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base address. Convert all board configurations to this new macro. This is the first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a clean up, no functional change.

As DM_SERIAL is mandatory now, we should get rid of CONFIG_MXC_UART_BASE.

I would prefer a patch that removes CONFIG_MXC_UART_BASE instead.

DM is mandatory in SPL too ? I doubt it.

#12 lore raw
Quoted 9 lines · Marek Vasut
Quoted 8 lines · Fabio Estevam

Hi Marek,

Quoted 4 lines · Marek Vasut

Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base address. Convert all board configurations to this new macro. This is the first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a clean up, no functional change.

Quoted 5 lines
Quoted 3 lines

As DM_SERIAL is mandatory now, we should get rid of CONFIG_MXC_UART_BASE.

I would prefer a patch that removes CONFIG_MXC_UART_BASE instead.

DM is mandatory in SPL too ? I doubt it.

It is strongly encouraged, but not mandatory. It is not used on I guess imx27/31/5, but is for all of the imx8 families. So CONFIG_MXC_UART_BASE still needs to be moved out of board.h files (and perhaps out of CONFIG namespace since it's not configurable, it's part of the SoC) and perhaps the path for imx8* is to drop the references since it's all DM?

Signature · 1 line
Tom
#13 lore raw
Quoted 14 lines · Tom Rini
Quoted 13 lines · Marek Vasut
Quoted 11 lines · Fabio Estevam

Hi Marek,

Quoted 4 lines · Marek Vasut

Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base address. Convert all board configurations to this new macro. This is the first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a clean up, no functional change.

As DM_SERIAL is mandatory now, we should get rid of CONFIG_MXC_UART_BASE.

I would prefer a patch that removes CONFIG_MXC_UART_BASE instead.

Quoted 8 lines
Quoted 1 line

DM is mandatory in SPL too ? I doubt it.

It is strongly encouraged, but not mandatory. It is not used on I guess imx27/31/5, but is for all of the imx8 families. So CONFIG_MXC_UART_BASE still needs to be moved out of board.h files (and perhaps out of CONFIG namespace since it's not configurable, it's part of the SoC) and perhaps the path for imx8* is to drop the references since it's all DM?

MX8M SPL is not DM serial either. But I think I will just postpone this cleanup until I have time to finish it.

#14 lore raw
Quoted 24 lines · Marek Vasut
Quoted 14 lines · Tom Rini
Quoted 13 lines · Marek Vasut
Quoted 11 lines · Fabio Estevam

Hi Marek,

Quoted 4 lines · Marek Vasut

Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base address. Convert all board configurations to this new macro. This is the first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a clean up, no functional change.

As DM_SERIAL is mandatory now, we should get rid of CONFIG_MXC_UART_BASE.

I would prefer a patch that removes CONFIG_MXC_UART_BASE instead.

Quoted 8 lines
Quoted 1 line

DM is mandatory in SPL too ? I doubt it.

It is strongly encouraged, but not mandatory. It is not used on I guess imx27/31/5, but is for all of the imx8 families. So CONFIG_MXC_UART_BASE still needs to be moved out of board.h files (and perhaps out of CONFIG namespace since it's not configurable, it's part of the SoC) and perhaps the path for imx8* is to drop the references since it's all DM?

Quoted 2 lines

MX8M SPL is not DM serial either. But I think I will just postpone this cleanup until I have time to finish it.

Right, sorry, I meant DM enabled in SPL to start with.

Signature · 1 line
Tom
#15 lore raw
In reply to Tom Rini
Quoted 8 lines · Tom Rini
Quoted 1 line

DM is mandatory in SPL too ? I doubt it.

It is strongly encouraged, but not mandatory. It is not used on I guess imx27/31/5, but is for all of the imx8 families. So CONFIG_MXC_UART_BASE still needs to be moved out of board.h files (and perhaps out of CONFIG namespace since it's not configurable, it's part of the SoC) and perhaps the path for imx8* is to drop the references since it's all DM?

Correct. In the defconfigs where CONFIG_DM_SERIAL=y and CONFIG_SPL_DM=y are selected the CONFIG_MXC_UART_BASE can be safely dropped.

Regards,

Fabio Estevam

#16 lore raw

PATCH 1/4 ARM: imx: imx8m: Introduce and use UART_BASE_ADDR(n)

In reply to Marek Vasut
Quoted 13 lines

Introduce helper macro UART_BASE_ADDR(n), which returns Nth UART base address. Convert all board configurations to this new macro. This is the first step toward switching CONFIG_MXC_UART_BASE to Kconfig. This is a clean up, no functional change.
The new macro contains compile-time test to verify N is in suitable range. The test works such that it multiplies constant N by constant double-negation of size of a non-empty structure, i.e. it multiplies constant N by constant 1 in each successful compilation case. The non-empty structure may contain C11 _Static_assert(), make use of this and place the kernel variant of static assert in there, so that it performs the compile-time check for N in the correct range. Note that it is not possible to directly use static_assert in compound statements, hence this convoluted construct.

Quoted 4 lines
Cc Fabio Estevam <[email protected]>
Cc Peng Fan <[email protected]>
Cc Stefano Babic <[email protected]>

Applied to u-boot-imx, master, thanks !

Best regards,
Stefano Babic

Signature · 5 lines
=====================================================================
DENX Software Engineering GmbH,      Managing Director: Wolfgang Denk
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany
Phone: +49-8142-66989-53 Fax: +49-8142-66989-80 Email: [email protected]
=====================================================================