clk: qoriq fixes and new fsl-flexspi driver
Subsystems (3)
v3 cover clk: qoriq fixes and new fsl-flexspi driver
The first two patches fix clock references for the ENETC and the FlexSPI on the LS1028A. These are intended to be picked up by the stable branches.
To circumvent further mistakes, I new device tree constants for the qoriq binding. This should make it far easier for humans to read the clockgen nodes.
The 4th patch convert the LS1028A device tree include to use the new constants.
The last five patches add a clock driver for the FlexSPI controller on layerscape SoCs. There is a single register which can control the divider value. Right now the LS1028A and the LX2160A aren't able to switch the SCK frequency on the FlexSPI interface.
I've included the first four patches in this series, otherwise there would be merge conflicts, because they depend on the new qoriq device tree constants.
Michael Walle (9):
arm64: dts: ls1028a: fix ENETC PTP clock input
arm64: dts: ls1028a: fix FlexSPI clock input
clk: qoriq: provide constants for the type
arm64: dts: ls1028a: use constants in the clockgen phandle
clk: divider: add devm_clk_hw_register_divider_table()
dt-bindings: clock: document the fsl-flexspi-clk driver
clk: fsl-flexspi: new driver
arm64: dts: ls1028a: fix FlexSPI clock
arm64: dts: lx2160a: fix FlexSPI clock
.../bindings/clock/fsl,flexspi-clock.yaml | 55 ++++++ .../arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 174 +++++++++++++----- .../arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 15 +- drivers/clk/Kconfig | 8 + drivers/clk/Makefile | 1 + drivers/clk/clk-divider.c | 34 ++++ drivers/clk/clk-fsl-flexspi.c | 106 +++++++++++ drivers/clk/clk-qoriq.c | 13 +- .../dt-bindings/clock/fsl,qoriq-clockgen.h | 15 ++ include/linux/clk-provider.h | 27 +++ 10 files changed, 393 insertions(+), 55 deletions(-) create mode 100644 Documentation/devicetree/bindings/clock/fsl,flexspi-clock.yaml create mode 100644 drivers/clk/clk-fsl-flexspi.c create mode 100644 include/dt-bindings/clock/fsl,qoriq-clockgen.h
Signature · 1 line
2.20.1
PATCH v3 1/9 arm64: dts: ls1028a: fix ENETC PTP clock input
On the LS1028A the ENETC reference clock is connected to 4th HWA output, see Figure 7 "Clock subsystem block diagram".
The PHC may run with a wrong frequency. ptp_qoriq_auto_config() will read the clock speed of the clock given in the device tree. It is likely that, on the reference board this wasn't noticed because both clocks have the same frequency. But this must not be always the case. Fix it.
---
Changes since v2:
- new patch
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +1 -1
@@ -961,7 +961,7 @@ ethernet@0,4 { compatible = "fsl,enetc-ptp"; reg = <0x000400 0 0 0 0>; - clocks = <&clockgen 4 0>; + clocks = <&clockgen 2 3>; little-endian; fsl,extts-fifo; };
Signature · 1 line
2.20.1
Shawn Guo
AppliedRe: [PATCH v3 1/9] arm64: dts: ls1028a: fix ENETC PTP clock input
Quoted 10 lines · Michael Walle
On the LS1028A the ENETC reference clock is connected to 4th HWA output, see Figure 7 "Clock subsystem block diagram".
The PHC may run with a wrong frequency.
ptp_qoriq_auto_config()will read the clock speed of the clock given in the device tree. It is likely that, on the reference board this wasn't noticed because both clocks have the same frequency. But this must not be always the case. Fix it.Fixes 49401003e260 ("arm64: dts: fsl: ls1028a: add ENETC 1588 timer node")Signed-off-by Michael Walle <[email protected]>
Applied, thanks.
PATCH v3 2/9 arm64: dts: ls1028a: fix FlexSPI clock input
In reply to Michael WalleOn the LS1028A the FlexSPI clock is connected to the first HWA output, see Figure 7 "Clock subsystem block diagram".
---
Changes since v2:
- new patch
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +1 -1
@@ -318,7 +318,7 @@ <0x0 0x20000000 0x0 0x10000000>; reg-names = "fspi_base", "fspi_mmap"; interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clocks = <&clockgen 2 0>, <&clockgen 2 0>; clock-names = "fspi_en", "fspi"; status = "disabled"; };
Signature · 1 line
2.20.1
Shawn Guo
AppliedRe: [PATCH v3 2/9] arm64: dts: ls1028a: fix FlexSPI clock input
Quoted 5 lines · Michael Walle
On the LS1028A the FlexSPI clock is connected to the first HWA output, see Figure 7 "Clock subsystem block diagram".
Fixes c77fae5ba09a ("arm64: dts: ls1028a: Add FlexSPI support")Signed-off-by Michael Walle <[email protected]>
Applied, thanks.
PATCH v3 3/9 clk: qoriq: provide constants for the type
In reply to Michael WalleTo avoid future mistakes in the device tree for the clockgen module, add constants for the clockgen subtype as well as a macro for the PLL divider.
---
Changes since v2:
- new patch
drivers/clk/clk-qoriq.c | 13 +++++++------ include/dt-bindings/clock/fsl,qoriq-clockgen.h | 15 +++++++++++++++ 2 files changed, 22 insertions(+), 6 deletions(-) create mode 100644 include/dt-bindings/clock/fsl,qoriq-clockgen.h
drivers/clk/clk-qoriq.c +7 -6
@@ -7,6 +7,7 @@#define pr_fmt (fmt) KBUILD_MODNAME ": " fmt +#include <dt-bindings/clock/fsl,qoriq-clockgen.h> #include <linux/clk.h> #include <linux/clk-provider.h> #include <linux/clkdev.h>
@@ -1368,33 +1369,33 @@ static struct clk *clockgen_clk_get(struct of_phandle_args *clkspec, void *data) idx = clkspec->args[1 ];switch (type) { -case 0 : +case QORIQ_CLK_SYSCLK :if (idx !=0 ) goto bad_args; clk = cg->sysclk;break ; -case 1 : +case QORIQ_CLK_CMUX :if (idx >=ARRAY_SIZE (cg->cmux)) goto bad_args; clk = cg->cmux[idx];break ; -case 2 : +case QORIQ_CLK_HWACCEL :if (idx >=ARRAY_SIZE (cg->hwaccel)) goto bad_args; clk = cg->hwaccel[idx];break ; -case 3 : +case QORIQ_CLK_FMAN :if (idx >=ARRAY_SIZE (cg->fman)) goto bad_args; clk = cg->fman[idx];break ; -case 4 : +case QORIQ_CLK_PLATFORM_PLL : pll = &cg->pll[PLATFORM_PLL ];if (idx >=ARRAY_SIZE (pll->div)) goto bad_args; clk = pll->div[idx].clk;break ; -case 5 : +case QORIQ_CLK_CORECLK :if (idx !=0 ) goto bad_args; clk = cg->coreclk;
include/dt-bindings/clock/fsl,qoriq-clockgen.h new file +15 -0
@@ -0,0 +1,15 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#ifndef DT_CLOCK_FSL_QORIQ_CLOCKGEN_H +#define DT_CLOCK_FSL_QORIQ_CLOCKGEN_H + +#define QORIQ_CLK_SYSCLK 0 +#define QORIQ_CLK_CMUX 1 +#define QORIQ_CLK_HWACCEL 2 +#define QORIQ_CLK_FMAN 3 +#define QORIQ_CLK_PLATFORM_PLL 4 +#define QORIQ_CLK_CORECLK 5 + +#define QORIQ_CLK_PLL_DIV (x) ((x) - 1) + +#endif /* DT_CLOCK_FSL_QORIQ_CLOCKGEN_H */
Signature · 1 line
2.20.1
Rob Herring
maintainerRe: [PATCH v3 3/9] clk: qoriq: provide constants for the type
Quoted 75 lines · Michael Walle
To avoid future mistakes in the device tree for the clockgen module, add constants for the clockgen subtype as well as a macro for the PLL divider.
Signed-off-by Michael Walle <[email protected]>---
Changes since v2:
- new patchdrivers/clk/clk-qoriq.c | 13 +++++++------ include/dt-bindings/clock/fsl,qoriq-clockgen.h | 15 +++++++++++++++ 2 files changed, 22 insertions(+), 6 deletions(-) create mode 100644 include/dt-bindings/clock/fsl,qoriq-clockgen.hdrivers/clk/clk-qoriq.c +7
-6@@ -7,6 +7,7 @@#define pr_fmt (fmt) KBUILD_MODNAME ": " fmt +#include <dt-bindings/clock/fsl,qoriq-clockgen.h> #include <linux/clk.h> #include <linux/clk-provider.h> #include <linux/clkdev.h> @@ -1368,33 +1369,33 @@ static struct clk *clockgen_clk_get(struct of_phandle_args *clkspec, void *data) idx = clkspec->args[1 ];switch (type) { -case 0 : +case QORIQ_CLK_SYSCLK :if (idx !=0 ) goto bad_args; clk = cg->sysclk;break ; -case 1 : +case QORIQ_CLK_CMUX :if (idx >=ARRAY_SIZE (cg->cmux)) goto bad_args; clk = cg->cmux[idx];break ; -case 2 : +case QORIQ_CLK_HWACCEL :if (idx >=ARRAY_SIZE (cg->hwaccel)) goto bad_args; clk = cg->hwaccel[idx];break ; -case 3 : +case QORIQ_CLK_FMAN :if (idx >=ARRAY_SIZE (cg->fman)) goto bad_args; clk = cg->fman[idx];break ; -case 4 : +case QORIQ_CLK_PLATFORM_PLL : pll = &cg->pll[PLATFORM_PLL ];if (idx >=ARRAY_SIZE (pll->div)) goto bad_args; clk = pll->div[idx].clk;break ; -case 5 : +case QORIQ_CLK_CORECLK :if (idx !=0 ) goto bad_args; clk = cg->coreclk;include/dt-bindings/clock/fsl,qoriq-clockgen.h new file +3
-0@@ -0,0 +1,15 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#ifndef DT_CLOCK_FSL_QORIQ_CLOCKGEN_H
include/dt-bindings/clock/fsl,qoriq-clockgen.h line 13
Quoted 10 lines
include/dt-bindings/clock/fsl,qoriq-clockgen.h new file +10
-0+#define DT_CLOCK_FSL_QORIQ_CLOCKGEN_H + +#define QORIQ_CLK_SYSCLK 0 +#define QORIQ_CLK_CMUX 1 +#define QORIQ_CLK_HWACCEL 2 +#define QORIQ_CLK_FMAN 3 +#define QORIQ_CLK_PLATFORM_PLL 4 +#define QORIQ_CLK_CORECLK 5 + +#define QORIQ_CLK_PLL_DIV (x) ((x) - 1)
This is not used and doesn't seem like part of the ABI (shared with dts files).
Quoted 5 lines
include/dt-bindings/clock/fsl,qoriq-clockgen.h new file +2
-0+ +#endif /* DT_CLOCK_FSL_QORIQ_CLOCKGEN_H */ Signature · 1 line
2.20.1
Re: [PATCH v3 3/9] clk: qoriq: provide constants for the type
Am 2020-11-09 23:05, schrieb Rob Herring:
Quoted 82 lines · Michael Walle
Quoted 81 lines
To avoid future mistakes in the device tree for the clockgen module, add constants for the clockgen subtype as well as a macro for the PLL divider.
Signed-off-by Michael Walle <[email protected]>---
Changes since v2:
- new patchdrivers/clk/clk-qoriq.c | 13 +++++++------ include/dt-bindings/clock/fsl,qoriq-clockgen.h | 15 +++++++++++++++ 2 files changed, 22 insertions(+), 6 deletions(-) create mode 100644 include/dt-bindings/clock/fsl,qoriq-clockgen.hdrivers/clk/clk-qoriq.c +7
-6@@ -7,6 +7,7 @@#define pr_fmt (fmt) KBUILD_MODNAME ": " fmt +#include <dt-bindings/clock/fsl,qoriq-clockgen.h> #include <linux/clk.h> #include <linux/clk-provider.h> #include <linux/clkdev.h> @@ -1368,33 +1369,33 @@ static struct clk *clockgen_clk_get(struct of_phandle_args *clkspec, void *data) idx = clkspec->args[1 ];switch (type) { -case 0 : +case QORIQ_CLK_SYSCLK :if (idx !=0 ) goto bad_args; clk = cg->sysclk;break ; -case 1 : +case QORIQ_CLK_CMUX :if (idx >=ARRAY_SIZE (cg->cmux)) goto bad_args; clk = cg->cmux[idx];break ; -case 2 : +case QORIQ_CLK_HWACCEL :if (idx >=ARRAY_SIZE (cg->hwaccel)) goto bad_args; clk = cg->hwaccel[idx];break ; -case 3 : +case QORIQ_CLK_FMAN :if (idx >=ARRAY_SIZE (cg->fman)) goto bad_args; clk = cg->fman[idx];break ; -case 4 : +case QORIQ_CLK_PLATFORM_PLL : pll = &cg->pll[PLATFORM_PLL ];if (idx >=ARRAY_SIZE (pll->div)) goto bad_args; clk = pll->div[idx].clk;break ; -case 5 : +case QORIQ_CLK_CORECLK :if (idx !=0 ) goto bad_args;drivers/clk/clk-qoriq.c +0
-0clk = cg->coreclk;include/dt-bindings/clock/fsl,qoriq-clockgen.h new file +8
-0@@ -0,0 +1,15 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#ifndef DT_CLOCK_FSL_QORIQ_CLOCKGEN_H +#define DT_CLOCK_FSL_QORIQ_CLOCKGEN_H + +#define QORIQ_CLK_SYSCLK 0 +#define QORIQ_CLK_CMUX 1 +#define QORIQ_CLK_HWACCEL 2
Quoted 8 lines
include/dt-bindings/clock/fsl,qoriq-clockgen.h line 13
Quoted 5 lines
include/dt-bindings/clock/fsl,qoriq-clockgen.h new file +5
-0+#define QORIQ_CLK_FMAN 3 +#define QORIQ_CLK_PLATFORM_PLL 4 +#define QORIQ_CLK_CORECLK 5 + +#define QORIQ_CLK_PLL_DIV (x) ((x) - 1)This is not used and doesn't seem like part of the ABI (shared with dts files).
TBH I haven't found a nice way to integrate this macro into the clock driver. It is used in the device tree for the type PLATFORM_PLL.
Previously, you had "<&clockgen 4 1>", where 4 is the PLATFORM_PLL and 1 is actually "div-by-2". Thus I replaced it by <&clockgen QORIQ_CLK_PLATFORM_PLL QORIQ_CLK_PLL_DIV(2)>. (I just realized that QORIQ_CLK_PLL_DIV_BY(2) might be a better name.)
I already figured, that this might be a problem, if that macro isn't used in the driver.
-michael
Re: [PATCH v3 3/9] clk: qoriq: provide constants for the type
Quoted 95 lines · Michael Walle
Am 2020-11-09 23:05, schrieb Rob Herring:
Quoted 84 lines · Michael Walle
Quoted 83 lines
To avoid future mistakes in the device tree for the clockgen module, add
constants for the clockgen subtype as well as a macro for the PLL divider.Signed-off-by Michael Walle <[email protected]>---
Changes since v2:
- new patchdrivers/clk/clk-qoriq.c | 13 +++++++------ include/dt-bindings/clock/fsl,qoriq-clockgen.h | 15 +++++++++++++++ 2 files changed, 22 insertions(+), 6 deletions(-) create mode 100644 include/dt-bindings/clock/fsl,qoriq-clockgen.hdrivers/clk/clk-qoriq.c +7
-6@@ -7,6 +7,7 @@#define pr_fmt (fmt) KBUILD_MODNAME ": " fmt +#include <dt-bindings/clock/fsl,qoriq-clockgen.h> #include <linux/clk.h> #include <linux/clk-provider.h> #include <linux/clkdev.h> @@ -1368,33 +1369,33 @@ static struct clk *clockgen_clk_get(struct of_phandle_args *clkspec, void *data) idx = clkspec->args[1 ];switch (type) { -case 0 : +case QORIQ_CLK_SYSCLK :if (idx !=0 ) goto bad_args; clk = cg->sysclk;break ; -case 1 : +case QORIQ_CLK_CMUX :if (idx >=ARRAY_SIZE (cg->cmux)) goto bad_args; clk = cg->cmux[idx];break ; -case 2 : +case QORIQ_CLK_HWACCEL :if (idx >=ARRAY_SIZE (cg->hwaccel)) goto bad_args; clk = cg->hwaccel[idx];break ; -case 3 : +case QORIQ_CLK_FMAN :if (idx >=ARRAY_SIZE (cg->fman)) goto bad_args; clk = cg->fman[idx];break ; -case 4 : +case QORIQ_CLK_PLATFORM_PLL : pll = &cg->pll[PLATFORM_PLL ];if (idx >=ARRAY_SIZE (pll->div)) goto bad_args; clk = pll->div[idx].clk;break ; -case 5 : +case QORIQ_CLK_CORECLK :if (idx !=0 ) goto bad_args;clk = cg->coreclk;include/dt-bindings/clock/fsl,qoriq-clockgen.h new file +8
-0@@ -0,0 +1,15 @@ +/* SPDX-License-Identifier: GPL-2.0-only */ + +#ifndef DT_CLOCK_FSL_QORIQ_CLOCKGEN_H +#define DT_CLOCK_FSL_QORIQ_CLOCKGEN_H + +#define QORIQ_CLK_SYSCLK 0 +#define QORIQ_CLK_CMUX 1 +#define QORIQ_CLK_HWACCEL 2Quoted 8 lines
include/dt-bindings/clock/fsl,qoriq-clockgen.h line 13
Quoted 5 lines
include/dt-bindings/clock/fsl,qoriq-clockgen.h new file +5
-0+#define QORIQ_CLK_FMAN 3 +#define QORIQ_CLK_PLATFORM_PLL 4 +#define QORIQ_CLK_CORECLK 5 + +#define QORIQ_CLK_PLL_DIV (x) ((x) - 1)This is not used and doesn't seem like part of the ABI (shared with dts files).
Quoted 6 lines
TBH I haven't found a nice way to integrate this macro into the clock driver. It is used in the device tree for the type
PLATFORM_PLL. Previously, you had "<&clockgen 4 1>", where 4 is thePLATFORM_PLLand 1 is actually "div-by-2". Thus I replaced it by <&clockgenQORIQ_CLK_PLATFORM_PLLQORIQ_CLK_PLL_DIV(2)>. (I just realized thatQORIQ_CLK_PLL_DIV_BY(2)might be a better name.)
Ah okay. I guess this is fine.
Rob
Re: [PATCH v3 3/9] clk: qoriq: provide constants for the type
In reply to Michael WalleQuoting Michael Walle (2020-11-08 10:51:07)
Quoted 6 lines
To avoid future mistakes in the device tree for the clockgen module, add constants for the clockgen subtype as well as a macro for the PLL divider.
Signed-off-by Michael Walle <[email protected]>---
Applied to clk-next
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v3 4/9 arm64: dts: ls1028a: use constants in the clockgen phandle
In reply to Michael WalleNow that we have constants, use them. This is just a mechanical change.
---
Changes since v2:
- new patch
.../arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 162 +++++++++++++----- 1 file changed, 116 insertions(+), 46 deletions(-)
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +116 -46
@@ -8,6 +8,7 @@ * */ +#include <dt-bindings/clock/fsl,qoriq-clockgen.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/thermal/thermal.h>
@@ -32,7 +33,7 @@ compatible = "arm,cortex-a72"; reg = <0x0>; enable-method = "psci"; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; next-level-cache = <&l2>; cpu-idle-states = <&CPU_PW20>; #cooling-cells = <2>;
@@ -43,7 +44,7 @@ compatible = "arm,cortex-a72"; reg = <0x1>; enable-method = "psci"; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; next-level-cache = <&l2>; cpu-idle-states = <&CPU_PW20>; #cooling-cells = <2>;
@@ -236,7 +237,8 @@ #size-cells = <0>; reg = <0x0 0x2000000 0x0 0x10000>; interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };
@@ -246,7 +248,8 @@ #size-cells = <0>; reg = <0x0 0x2010000 0x0 0x10000>; interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };
@@ -256,7 +259,8 @@ #size-cells = <0>; reg = <0x0 0x2020000 0x0 0x10000>; interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };
@@ -266,7 +270,8 @@ #size-cells = <0>; reg = <0x0 0x2030000 0x0 0x10000>; interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };
@@ -276,7 +281,8 @@ #size-cells = <0>; reg = <0x0 0x2040000 0x0 0x10000>; interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };
@@ -286,7 +292,8 @@ #size-cells = <0>; reg = <0x0 0x2050000 0x0 0x10000>; interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };
@@ -296,7 +303,8 @@ #size-cells = <0>; reg = <0x0 0x2060000 0x0 0x10000>; interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };
@@ -306,7 +314,8 @@ #size-cells = <0>; reg = <0x0 0x2070000 0x0 0x10000>; interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };
@@ -318,7 +327,8 @@ <0x0 0x20000000 0x0 0x10000000>; reg-names = "fspi_base", "fspi_mmap"; interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 2 0>, <&clockgen 2 0>; + clocks = <&clockgen QORIQ_CLK_HWACCEL 0>, + <&clockgen QORIQ_CLK_HWACCEL 0>; clock-names = "fspi_en", "fspi"; status = "disabled"; };
@@ -330,7 +340,8 @@ reg = <0x0 0x2100000 0x0 0x10000>; interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; clock-names = "dspi"; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; dmas = <&edma0 0 62>, <&edma0 0 60>; dma-names = "tx", "rx"; spi-num-chipselects = <4>;
@@ -345,7 +356,8 @@ reg = <0x0 0x2110000 0x0 0x10000>; interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; clock-names = "dspi"; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; dmas = <&edma0 0 58>, <&edma0 0 56>; dma-names = "tx", "rx"; spi-num-chipselects = <4>;
@@ -360,7 +372,8 @@ reg = <0x0 0x2120000 0x0 0x10000>; interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; clock-names = "dspi"; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; dmas = <&edma0 0 54>, <&edma0 0 2>; dma-names = "tx", "rx"; spi-num-chipselects = <3>;
@@ -373,7 +386,7 @@ reg = <0x0 0x2140000 0x0 0x10000>; interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <0>; /* fixed up by bootloader */ - clocks = <&clockgen 2 1>; + clocks = <&clockgen QORIQ_CLK_HWACCEL 1>; voltage-ranges = <1800 1800 3300 3300>; sdhci,auto-cmd12; little-endian;
@@ -386,7 +399,7 @@ reg = <0x0 0x2150000 0x0 0x10000>; interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <0>; /* fixed up by bootloader */ - clocks = <&clockgen 2 1>; + clocks = <&clockgen QORIQ_CLK_HWACCEL 1>; voltage-ranges = <1800 1800 3300 3300>; sdhci,auto-cmd12; broken-cd;
@@ -399,7 +412,8 @@ compatible = "fsl,ls1028ar1-flexcan", "fsl,lx2160ar1-flexcan"; reg = <0x0 0x2180000 0x0 0x10000>; interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&sysclk>, <&clockgen 4 1>; + clocks = <&sysclk>, <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg", "per"; status = "disabled"; };
@@ -408,7 +422,8 @@ compatible = "fsl,ls1028ar1-flexcan", "fsl,lx2160ar1-flexcan"; reg = <0x0 0x2190000 0x0 0x10000>; interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&sysclk>, <&clockgen 4 1>; + clocks = <&sysclk>, <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg", "per"; status = "disabled"; };
@@ -417,7 +432,8 @@ compatible = "fsl,ns16550", "ns16550a"; reg = <0x00 0x21c0500 0x0 0x100>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; status = "disabled"; };
@@ -425,7 +441,8 @@ compatible = "fsl,ns16550", "ns16550a"; reg = <0x00 0x21c0600 0x0 0x100>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; status = "disabled"; };
@@ -434,7 +451,8 @@ compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x2260000 0x0 0x1000>; interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; dma-names = "rx","tx"; dmas = <&edma0 1 32>,
@@ -446,7 +464,8 @@ compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x2270000 0x0 0x1000>; interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; dma-names = "rx","tx"; dmas = <&edma0 1 30>,
@@ -458,7 +477,8 @@ compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x2280000 0x0 0x1000>; interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; dma-names = "rx","tx"; dmas = <&edma0 1 28>,
@@ -470,7 +490,8 @@ compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x2290000 0x0 0x1000>; interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; dma-names = "rx","tx"; dmas = <&edma0 1 26>,
@@ -482,7 +503,8 @@ compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x22a0000 0x0 0x1000>; interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; dma-names = "rx","tx"; dmas = <&edma0 1 24>,
@@ -494,7 +516,8 @@ compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x22b0000 0x0 0x1000>; interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; dma-names = "rx","tx"; dmas = <&edma0 1 22>,
@@ -513,8 +536,10 @@ interrupt-names = "edma-tx", "edma-err"; dma-channels = <32>; clock-names = "dmamux0", "dmamux1"; - clocks = <&clockgen 4 1>, - <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; }; gpio1: gpio@2300000 {
@@ -576,7 +601,8 @@ <0x7 0x100520 0x0 0x4>; reg-names = "ahci", "sata-ecc"; interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; status = "disabled"; };
@@ -748,14 +774,20 @@ cluster1_core0_watchdog: watchdog@c000000 { compatible = "arm,sp805", "arm,primecell"; reg = <0x0 0xc000000 0x0 0x1000>; - clocks = <&clockgen 4 15>, <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; clock-names = "wdog_clk", "apb_pclk"; }; cluster1_core1_watchdog: watchdog@c010000 { compatible = "arm,sp805", "arm,primecell"; reg = <0x0 0xc010000 0x0 0x1000>; - clocks = <&clockgen 4 15>, <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; clock-names = "wdog_clk", "apb_pclk"; };
@@ -764,8 +796,14 @@ compatible = "fsl,vf610-sai"; reg = <0x0 0xf100000 0x0 0x10000>; interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>, <&clockgen 4 1>, - <&clockgen 4 1>, <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 1 4>,
@@ -779,8 +817,14 @@ compatible = "fsl,vf610-sai"; reg = <0x0 0xf110000 0x0 0x10000>; interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>, <&clockgen 4 1>, - <&clockgen 4 1>, <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 1 6>,
@@ -794,8 +838,14 @@ compatible = "fsl,vf610-sai"; reg = <0x0 0xf120000 0x0 0x10000>; interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>, <&clockgen 4 1>, - <&clockgen 4 1>, <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 1 8>,
@@ -809,8 +859,14 @@ compatible = "fsl,vf610-sai"; reg = <0x0 0xf130000 0x0 0x10000>; interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>, <&clockgen 4 1>, - <&clockgen 4 1>, <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 1 10>,
@@ -824,8 +880,14 @@ compatible = "fsl,vf610-sai"; reg = <0x0 0xf140000 0x0 0x10000>; interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>, <&clockgen 4 1>, - <&clockgen 4 1>, <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 1 12>,
@@ -839,8 +901,14 @@ compatible = "fsl,vf610-sai"; reg = <0x0 0xf150000 0x0 0x10000>; interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>, <&clockgen 4 1>, - <&clockgen 4 1>, <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 1 14>,
@@ -961,7 +1029,7 @@ ethernet@0,4 { compatible = "fsl,enetc-ptp"; reg = <0x000400 0 0 0 0>; - clocks = <&clockgen 2 3>; + clocks = <&clockgen QORIQ_CLK_HWACCEL 3>; little-endian; fsl,extts-fifo; };
@@ -1056,8 +1124,10 @@ interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>, <0 223 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "DE", "SE"; - clocks = <&dpclk>, <&clockgen 2 2>, <&clockgen 2 2>, - <&clockgen 2 2>; + clocks = <&dpclk>, + <&clockgen QORIQ_CLK_HWACCEL 2>, + <&clockgen QORIQ_CLK_HWACCEL 2>, + <&clockgen QORIQ_CLK_HWACCEL 2>; clock-names = "pxlclk", "mclk", "aclk", "pclk"; arm,malidp-output-port-lines = /bits/ 8 <8 8 8>; arm,malidp-arqos-value = <0xd000d000>;
Signature · 1 line
2.20.1
RE: [EXT] [PATCH v3 4/9] arm64: dts: ls1028a: use constants in the clockgen phandle
HI Michael,
Quoted 14 lines
-----Original Message-----
From: Michael Walle <[email protected]>
Sent: Monday, November 9, 2020 12:21 AM
To: [email protected]; [email protected]; linux- [email protected]; [email protected]
Cc: Michael Turquette <[email protected]>; Stephen Boyd <[email protected]>; Rob Herring <[email protected]>; Shawn Guo <[email protected]>; Leo Li <[email protected]>; Y.b. Lu <[email protected]>; Xiaowei Bao <[email protected]>; Ashish Kumar <[email protected]>; Vladimir Oltean <[email protected]>; Michael Walle <[email protected]>
Subject: [EXT] [PATCH v3 4/9] arm64: dts: ls1028a: use constants in the clockgen phandle
Quoted 8 lines
Caution: EXT Email
Now that we have constants, use them. This is just a mechanical change.
Signed-off-by Michael Walle <[email protected]>---
Changes since v2:
- new patch
I am not able to apply this patch cleanly, does it have any dependency patch that I have missed? My assumption is that this patch series is superset of
Series 1: [1/4] dt-bindings: clock: document the fsl-flexspi-clk driver
And
Series 2: [v2,1/5] clk: divider: add devm_clk_hw_register_divider_table()
Regards
Ashish
Quoted 431 lines
.../arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 162 +++++++++++++----- 1 file changed, 116 insertions(+), 46 deletions(-)arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +2
-1@@ -8,6 +8,7 @@ * */ +#include <dt-bindings/clock/fsl,qoriq-clockgen.h> #include <dt-bindings/interrupt-controller/arm-gic.h> #include <dt-bindings/thermal/thermal.h>@@ -32,7 +33,7 @@ compatible = "arm,cortex-a72"; reg = <0x0>; enable-method = "psci"; - clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; next-level-cache = <&l2>; cpu-idle-states = <&CPU_PW20>; #cooling-cells = <2>; @@ -43,7 +44,7 @@compatible = "arm,cortex-a72"; reg = <0x1>; enable-method = "psci";arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +21
-11- clocks = <&clockgen 1 0>; + clocks = <&clockgen QORIQ_CLK_CMUX 0>; next-level-cache = <&l2>; cpu-idle-states = <&CPU_PW20>; #cooling-cells = <2>; @@ -236,7 +237,8 @@ #size-cells = <0>; reg = <0x0 0x2000000 0x0 0x10000>; interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };@@ -246,7 +248,8 @@ #size-cells = <0>; reg = <0x0 0x2010000 0x0 0x10000>; interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };@@ -256,7 +259,8 @@ #size-cells = <0>; reg = <0x0 0x2020000 0x0 0x10000>; interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };@@ -266,7 +270,8 @@ #size-cells = <0>; reg = <0x0 0x2030000 0x0 0x10000>; interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };@@ -276,7 +281,8 @@ #size-cells = <0>; reg = <0x0 0x2040000 0x0 0x10000>; interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };@@ -286,7 +292,8 @@ #size-cells = <0>; reg = <0x0 0x2050000 0x0 0x10000>; interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };@@ -296,7 +303,8 @@ #size-cells = <0>; reg = <0x0 0x2060000 0x0 0x10000>; interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };@@ -306,7 +314,8 @@ #size-cells = <0>; reg = <0x0 0x2070000 0x0 0x10000>; interrupts = <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(4)>; status = "disabled"; };@@ -318,7 +327,8 @@ <0x0 0x20000000 0x0 0x10000000>; reg-names = "fspi_base", "fspi_mmap"; interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 2 0>, <&clockgen 2 0>; + clocks = <&clockgen QORIQ_CLK_HWACCEL 0>, + <&clockgen QORIQ_CLK_HWACCEL 0>; clock-names = "fspi_en", "fspi"; status = "disabled"; };@@ -330,7 +340,8 @@ reg = <0x0 0x2100000 0x0 0x10000>; interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; clock-names = "dspi"; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; dmas = <&edma0 0 62>, <&edma0 0 60>; dma-names = "tx", "rx"; spi-num-chipselects = <4>; @@ -345,7 +356,8 @@reg = <0x0 0x2110000 0x0 0x10000>; interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; clock-names = "dspi";arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +18
-9- clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; dmas = <&edma0 0 58>, <&edma0 0 56>; dma-names = "tx", "rx"; spi-num-chipselects = <4>; @@ -360,7 +372,8 @@ reg = <0x0 0x2120000 0x0 0x10000>; interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; clock-names = "dspi"; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; dmas = <&edma0 0 54>, <&edma0 0 2>; dma-names = "tx", "rx"; spi-num-chipselects = <3>; @@ -373,7 +386,7 @@ reg = <0x0 0x2140000 0x0 0x10000>; interrupts = <GIC_SPI 28 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <0>; /* fixed up by bootloader */ - clocks = <&clockgen 2 1>; + clocks = <&clockgen QORIQ_CLK_HWACCEL 1>; voltage-ranges = <1800 1800 3300 3300>; sdhci,auto-cmd12; little-endian;@@ -386,7 +399,7 @@ reg = <0x0 0x2150000 0x0 0x10000>; interrupts = <GIC_SPI 63 IRQ_TYPE_LEVEL_HIGH>; clock-frequency = <0>; /* fixed up by bootloader */ - clocks = <&clockgen 2 1>; + clocks = <&clockgen QORIQ_CLK_HWACCEL 1>; voltage-ranges = <1800 1800 3300 3300>; sdhci,auto-cmd12; broken-cd;@@ -399,7 +412,8 @@ compatible = "fsl,ls1028ar1-flexcan", "fsl,lx2160ar1-flexcan"; reg = <0x0 0x2180000 0x0 0x10000>; interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&sysclk>, <&clockgen 4 1>; + clocks = <&sysclk>, <&clockgen QORIQ_CLK_PLATFORM_PLL + + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg", "per"; status = "disabled"; };@@ -408,7 +422,8 @@ compatible = "fsl,ls1028ar1-flexcan", "fsl,lx2160ar1-flexcan"; reg = <0x0 0x2190000 0x0 0x10000>; interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&sysclk>, <&clockgen 4 1>; + clocks = <&sysclk>, <&clockgen QORIQ_CLK_PLATFORM_PLL + + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg", "per"; status = "disabled"; };@@ -417,7 +432,8 @@ compatible = "fsl,ns16550", "ns16550a"; reg = <0x00 0x21c0500 0x0 0x100>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; status = "disabled"; };@@ -425,7 +441,8 @@ compatible = "fsl,ns16550", "ns16550a"; reg = <0x00 0x21c0600 0x0 0x100>; interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; status = "disabled"; };@@ -434,7 +451,8 @@ compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x2260000 0x0 0x1000>; interrupts = <GIC_SPI 232 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; dma-names = "rx","tx"; dmas = <&edma0 1 32>, @@ -446,7 +464,8 @@compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x2270000 0x0 0x1000>; interrupts = <GIC_SPI 233 IRQ_TYPE_LEVEL_HIGH>;arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +32
-12- clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; dma-names = "rx","tx"; dmas = <&edma0 1 30>, @@ -458,7 +477,8 @@ compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x2280000 0x0 0x1000>; interrupts = <GIC_SPI 234 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; dma-names = "rx","tx"; dmas = <&edma0 1 28>, @@ -470,7 +490,8 @@ compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x2290000 0x0 0x1000>; interrupts = <GIC_SPI 235 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; dma-names = "rx","tx"; dmas = <&edma0 1 26>, @@ -482,7 +503,8 @@ compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x22a0000 0x0 0x1000>; interrupts = <GIC_SPI 236 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; dma-names = "rx","tx"; dmas = <&edma0 1 24>, @@ -494,7 +516,8 @@ compatible = "fsl,ls1028a-lpuart"; reg = <0x0 0x22b0000 0x0 0x1000>; interrupts = <GIC_SPI 237 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "ipg"; dma-names = "rx","tx"; dmas = <&edma0 1 22>, @@ -513,8 +536,10 @@ interrupt-names = "edma-tx", "edma-err"; dma-channels = <32>; clock-names = "dmamux0", "dmamux1"; - clocks = <&clockgen 4 1>, - <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; }; gpio1: gpio@2300000 {@@ -576,7 +601,8 @@ <0x7 0x100520 0x0 0x4>; reg-names = "ahci", "sata-ecc"; interrupts = <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; status = "disabled"; };@@ -748,14 +774,20 @@ cluster1_core0_watchdog: watchdog@c000000 { compatible = "arm,sp805", "arm,primecell"; reg = <0x0 0xc000000 0x0 0x1000>; - clocks = <&clockgen 4 15>, <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; clock-names = "wdog_clk", "apb_pclk"; }; cluster1_core1_watchdog: watchdog@c010000 { compatible = "arm,sp805", "arm,primecell"; reg = <0x0 0xc010000 0x0 0x1000>; - clocks = <&clockgen 4 15>, <&clockgen 4 15>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(16)>; clock-names = "wdog_clk", "apb_pclk"; };@@ -764,8 +796,14 @@ compatible = "fsl,vf610-sai"; reg = <0x0 0xf100000 0x0 0x10000>; interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>, <&clockgen 4 1>, - <&clockgen 4 1>, <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 1 4>, @@ -779,8 +817,14 @@compatible = "fsl,vf610-sai"; reg = <0x0 0xf110000 0x0 0x10000>; interrupts = <GIC_SPI 82 IRQ_TYPE_LEVEL_HIGH>;arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +46
-14- clocks = <&clockgen 4 1>, <&clockgen 4 1>, - <&clockgen 4 1>, <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 1 6>, @@ -794,8 +838,14 @@ compatible = "fsl,vf610-sai"; reg = <0x0 0xf120000 0x0 0x10000>; interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>, <&clockgen 4 1>, - <&clockgen 4 1>, <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 1 8>, @@ -809,8 +859,14 @@ compatible = "fsl,vf610-sai"; reg = <0x0 0xf130000 0x0 0x10000>; interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>, <&clockgen 4 1>, - <&clockgen 4 1>, <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 1 10>, @@ -824,8 +880,14 @@ compatible = "fsl,vf610-sai"; reg = <0x0 0xf140000 0x0 0x10000>; interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>, <&clockgen 4 1>, - <&clockgen 4 1>, <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 1 12>, @@ -839,8 +901,14 @@ compatible = "fsl,vf610-sai"; reg = <0x0 0xf150000 0x0 0x10000>; interrupts = <GIC_SPI 84 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 1>, <&clockgen 4 1>, - <&clockgen 4 1>, <&clockgen 4 1>; + clocks = <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>, + <&clockgen QORIQ_CLK_PLATFORM_PLL + QORIQ_CLK_PLL_DIV(2)>; clock-names = "bus", "mclk1", "mclk2", "mclk3"; dma-names = "tx", "rx"; dmas = <&edma0 1 14>, @@ -961,7 +1029,7 @@ ethernet@0,4 { compatible = "fsl,enetc-ptp"; reg = <0x000400 0 0 0 0>; - clocks = <&clockgen 2 3>; + clocks = <&clockgen QORIQ_CLK_HWACCEL + 3>; little-endian; fsl,extts-fifo; };@@ -1056,8 +1124,10 @@ interrupts = <0 222 IRQ_TYPE_LEVEL_HIGH>, <0 223 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "DE", "SE"; - clocks = <&dpclk>, <&clockgen 2 2>, <&clockgen 2 2>, - <&clockgen 2 2>; + clocks = <&dpclk>, + <&clockgen QORIQ_CLK_HWACCEL 2>, + <&clockgen QORIQ_CLK_HWACCEL 2>, + <&clockgen QORIQ_CLK_HWACCEL 2>; clock-names = "pxlclk", "mclk", "aclk", "pclk"; arm,malidp-output-port-lines = /bits/ 8 <8 8 8>; arm,malidp-arqos-value = <0xd000d000>; --2.20.1
Re: [PATCH v3 4/9] arm64: dts: ls1028a: use constants in the clockgen phandle
Hi Ashish,
Am 2020-11-20 10:25, schrieb Ashish Kumar:
Quoted 2 lines
I am not able to apply this patch cleanly, does it have any dependency patch that I have missed?
What is your base? I've just tried to apply this series (stand-alone) onto linux-next and it applied cleanly.
Quoted 4 lines
My assumption is that this patch series is superset of
Series 1: [1/4] dt-bindings: clock: document the fsl-flexspi-clk driver And
Series 2: [v2,1/5] clk: divider: adddevm_clk_hw_register_divider_table()
That is correct.
-michael
RE: [EXT] Re: [PATCH v3 4/9] arm64: dts: ls1028a: use constants in the clockgen phandle
Hi Michelle,
Quoted 15 lines
-----Original Message-----
From: Michael Walle <[email protected]>
Sent: Friday, November 20, 2020 3:09 PM
To: Ashish Kumar <[email protected]>
Cc: [email protected]; [email protected]; linux- [email protected]; [email protected]; Michael Turquette <[email protected]>; Stephen Boyd <[email protected]>; Rob Herring <[email protected]>; Shawn Guo <[email protected]>; Leo Li <[email protected]>; Y.b. Lu <[email protected]>; Xiaowei Bao <[email protected]>; Vladimir Oltean <[email protected]>
Subject: [EXT] Re: [PATCH v3 4/9] arm64: dts: ls1028a: use constants in the clockgen phandleCaution: EXT Email
Quoted 8 lines
Hi Ashish,
Am 2020-11-20 10:25, schrieb Ashish Kumar:
Quoted 2 lines
I am not able to apply this patch cleanly, does it have any dependency patch that I have missed?
What is your base? I've just tried to apply this series (stand-alone) onto linux- next and it applied cleanly.
I used https://github.com/torvalds/linux.git should I try this git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux.git ?
Regards
Ashish
Quoted 9 lines
Quoted 5 lines
My assumption is that this patch series is superset of Series 1: [1/4]
dt-bindings: clock: document the fsl-flexspi-clk driver And Series 2:
[v2,1/5] clk: divider: adddevm_clk_hw_register_divider_table()That is correct.
-michael
Re: [PATCH v3 4/9] arm64: dts: ls1028a: use constants in the clockgen phandle
Hi Ashish,
Am 2020-11-20 10:51, schrieb Ashish Kumar:
Quoted 17 lines
Quoted 17 lines
-----Original Message-----
From: Michael Walle <[email protected]>
Sent: Friday, November 20, 2020 3:09 PM
To: Ashish Kumar <[email protected]>
Cc: [email protected]; [email protected]; linux- [email protected]; [email protected]; Michael Turquette <[email protected]>; Stephen Boyd <[email protected]>; Rob Herring <[email protected]>; Shawn Guo <[email protected]>; Leo Li <[email protected]>; Y.b. Lu <[email protected]>; Xiaowei Bao <[email protected]>; Vladimir Oltean <[email protected]>
Subject: [EXT] Re: [PATCH v3 4/9] arm64: dts: ls1028a: use constants in the clockgen phandleCaution: EXT Email
Hi Ashish,
Quoted 8 lines
Quoted 6 lines
Am 2020-11-20 10:25, schrieb Ashish Kumar:
Quoted 2 lines
I am not able to apply this patch cleanly, does it have any dependency patch that I have missed?
What is your base? I've just tried to apply this series (stand-alone) onto linux- next and it applied cleanly.
I used https://github.com/torvalds/linux.git should I try this
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux.git?
Mh, I just tried clk-next. clk-next is missing some device tree changes. So, parts of this series should go through the soc tree (shawnguo) and some through clk-next (or acked by Stephen Boyd).
If you want to apply it, use the for-next branch of the soc tree:git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux.git
-michael
PATCH v3 5/9 clk: divider: add devm_clk_hw_register_divider_table()
In reply to Michael WalleThis will simplify drivers which would only unregister the clk in their remove() op.
---
Changes since v2:
- none
Changes since v1:
- new patch
drivers/clk/clk-divider.c | 34 ++++++++++++++++++++++++++++++++++ include/linux/clk-provider.h | 27 +++++++++++++++++++++++++++ 2 files changed, 61 insertions(+)
drivers/clk/clk-divider.c +34 -0
@@ -8,6 +8,7 @@*/ #include <linux/clk-provider.h> +#include <linux/device.h> #include <linux/module.h> #include <linux/slab.h> #include <linux/io.h>
@@ -578,3 +579,36 @@ void clk_hw_unregister_divider(struct clk_hw *hw)kfree (div); }EXPORT_SYMBOL_GPL (clk_hw_unregister_divider); + +static void devm_clk_hw_release_divider (struct device *dev,void *res) +{ +clk_hw_unregister_divider (*(struct clk_hw **)res); +} + +struct clk_hw *__devm_clk_hw_register_divider (struct device *dev, +struct device_node *np,const char *name, +const char *parent_name,const struct clk_hw *parent_hw, +const struct clk_parent_data *parent_data,unsigned long flags, +void __iomem *reg,u8 shift,u8 width,u8 clk_divider_flags, +const struct clk_div_table *table,spinlock_t *lock) +{ +struct clk_hw **ptr, *hw; + + ptr =devres_alloc (devm_clk_hw_release_divider,sizeof (*ptr),GFP_KERNEL ); +if (!ptr) +return ERR_PTR (-ENOMEM ); + + hw =__clk_hw_register_divider (dev, np, name, parent_name, parent_hw, + parent_data, flags, reg, shift, width, + clk_divider_flags, table, lock); + +if (!IS_ERR (hw)) { + *ptr = hw; +devres_add (dev, ptr); + }else { +devres_free (ptr); + } + +return hw; +} +EXPORT_SYMBOL_GPL (__devm_clk_hw_register_divider);
include/linux/clk-provider.h +27 -0
@@ -639,6 +639,12 @@ struct clk_hw *__clk_hw_register_divider(struct device *dev, const struct clk_parent_data *parent_data, unsigned long flags, void __iomem *reg, u8 shift, u8 width, u8 clk_divider_flags, const struct clk_div_table *table, spinlock_t *lock); +struct clk_hw *__devm_clk_hw_register_divider (struct device *dev, +struct device_node *np,const char *name, +const char *parent_name,const struct clk_hw *parent_hw, +const struct clk_parent_data *parent_data,unsigned long flags, +void __iomem *reg,u8 shift,u8 width,u8 clk_divider_flags, +const struct clk_div_table *table,spinlock_t *lock); struct clk *clk_register_divider_table(struct device *dev, const char *name, const char *parent_name, unsigned long flags, void __iomem *reg, u8 shift, u8 width,
@@ -779,6 +785,27 @@ struct clk *clk_register_divider_table(struct device *dev, const char *name, (parent_data), (flags), (reg), (shift), \ (width), (clk_divider_flags), (table), \ (lock)) +/** +* devm_clk_hw_register_divider_table - register a table based divider clock +* with the clock framework (devres variant) +* @dev: device registering this clock +* @name: name of this clock +* @parent_name: name of clock's parent +* @flags: framework-specific flags +* @reg: register address to adjust divider +* @shift: number of bits to shift the bitfield +* @width: width of the bitfield +* @clk_divider_flags: divider-specific flags for this clock +* @table: array of divider/value pairs ending with a div set to 0 +* @lock: shared register lock for this clock +*/ +#define devm_clk_hw_register_divider_table (dev, name, parent_name, flags, \ + reg, shift, width, \ + clk_divider_flags, table, lock) \ + __devm_clk_hw_register_divider((dev), NULL, (name), (parent_name), \ + NULL, NULL, (flags), (reg), (shift), \ + (width), (clk_divider_flags), (table), \ + (lock))void clk_unregister_divider (struct clk *clk);void clk_hw_unregister_divider (struct clk_hw *hw);
Signature · 1 line
2.20.1
Re: [PATCH v3 5/9] clk: divider: add devm_clk_hw_register_divider_table()
Quoting Michael Walle (2020-11-08 10:51:09)
Quoted 5 lines
This will simplify drivers which would only unregister the clk in their
remove()op.Signed-off-by Michael Walle <[email protected]>---
Applied to clk-next
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v3 6/9 dt-bindings: clock: document the fsl-flexspi-clk driver
In reply to Michael Walle---
Changes since v2:
- none
Changes since v1:
- new patch
.../bindings/clock/fsl,flexspi-clock.yaml | 55 +++++++++++++++++++ 1 file changed, 55 insertions(+) create mode 100644 Documentation/devicetree/bindings/clock/fsl,flexspi-clock.yaml
Documentation/devicetree/bindings/clock/fsl,flexspi-clock.yaml new file +55 -0
@@ -0,0 +1,55 @@ +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/clock/fsl,flexspi-clock.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Freescale FlexSPI clock driver for Layerscape SoCs + +maintainers: + - Michael Walle <[email protected]> + +description: + The Freescale Layerscape SoCs have a special FlexSPI clock which is + derived from the platform PLL. + +properties: + compatible: + enum: + - fsl,ls1028a-flexspi-clk + - fsl,lx2160a-flexspi-clk + + reg: + maxItems: 1 + + clocks: + maxItems: 1 + + '#clock-cells': + const: 0 + + clock-output-names: + maxItems: 1 + +required: + - compatible + - reg + - clocks + - '#clock-cells' + +additionalProperties: false + +examples: + - | + dcfg { + #address-cells = <1>; + #size-cells = <1>; + + fspi_clk: clock-controller@900 { + compatible = "fsl,ls1028a-flexspi-clk"; + reg = <0x900 0x4>; + #clock-cells = <0>; + clocks = <&parentclk>; + clock-output-names = "fspi_clk"; + }; + };
Signature · 1 line
2.20.1
Re: [PATCH v3 6/9] dt-bindings: clock: document the fsl-flexspi-clk driver
Quoting Michael Walle (2020-11-08 10:51:10)
Quoted 3 lines
Signed-off-by Michael Walle <[email protected]>Reviewed-by Rob Herring <[email protected]>---
Applied to clk-next
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v3 7/9 clk: fsl-flexspi: new driver
In reply to Michael WalleAdd support for the FlexSPI clock on Freescale Layerscape SoCs. The clock is a simple divider based one and is located inside the device configuration space (DCFG).
This will allow switching the SCK frequencies for the FlexSPI interface on the LS1028A and the LX2160A.
---
Changes since v2:
- none
Changes since v1:
- use devm_clk_hw_register_divider_table() and drop remove()
drivers/clk/Kconfig | 8 +++ drivers/clk/Makefile | 1 + drivers/clk/clk-fsl-flexspi.c | 106 ++++++++++++++++++++++++++++++++++ 3 files changed, 115 insertions(+) create mode 100644 drivers/clk/clk-fsl-flexspi.c
drivers/clk/Kconfig +8 -0
@@ -188,6 +188,14 @@ config COMMON_CLK_CS2000_CP help If you say yes here you get support for the CS2000 clock multiplier. +config COMMON_CLK_FSL_FLEXSPI + tristate "Clock driver for FlexSPI on Layerscape SoCs" + depends on ARCH_LAYERSCAPE || COMPILE_TEST + default ARCH_LAYERSCAPE && SPI_NXP_FLEXSPI + help + On Layerscape SoCs there is a special clock for the FlexSPI + interface. + config COMMON_CLK_FSL_SAI bool "Clock driver for BCLK of Freescale SAI cores" depends on ARCH_LAYERSCAPE || COMPILE_TEST
drivers/clk/Makefile +1 -0
@@ -30,6 +30,7 @@ obj-$(CONFIG_COMMON_CLK_CS2000_CP) += clk-cs2000-cp.o obj-$(CONFIG_ARCH_EFM32) += clk-efm32gg.o obj-$(CONFIG_ARCH_SPARX5) += clk-sparx5.o obj-$(CONFIG_COMMON_CLK_FIXED_MMIO) += clk-fixed-mmio.o +obj-$(CONFIG_COMMON_CLK_FSL_FLEXSPI) += clk-fsl-flexspi.o obj-$(CONFIG_COMMON_CLK_FSL_SAI) += clk-fsl-sai.o obj-$(CONFIG_COMMON_CLK_GEMINI) += clk-gemini.o obj-$(CONFIG_COMMON_CLK_ASPEED) += clk-aspeed.o
drivers/clk/clk-fsl-flexspi.c new file +106 -0
106 lines not on this page · raw message
Signature · 1 line
2.20.1
Re: [PATCH v3 7/9] clk: fsl-flexspi: new driver
Quoting Michael Walle (2020-11-08 10:51:11)
Quoted 9 lines
Add support for the FlexSPI clock on Freescale Layerscape SoCs. The clock is a simple divider based one and is located inside the device configuration space (DCFG).
This will allow switching the SCK frequencies for the FlexSPI interface on the LS1028A and the LX2160A.
Signed-off-by Michael Walle <[email protected]>---
Applied to clk-next
_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
PATCH v3 8/9 arm64: dts: ls1028a: fix FlexSPI clock
In reply to Michael WalleNow that we have a proper driver for the FlexSPI interface use it. This will fix SCK frequency switching on Layerscape SoCs.
This was tested on the Kontron sl28 board.
---
Changes since v2:
- use device tree constants for clockgen
- also use &fspi_clk for fspi_en clock
Changes since v1:
- none
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi | 16 +++++++++++++--- 1 file changed, 13 insertions(+), 3 deletions(-)
arch/arm64/boot/dts/freescale/fsl-ls1028a.dtsi +13 -3
@@ -207,9 +207,20 @@ }; dcfg: syscon@1e00000 { - compatible = "fsl,ls1028a-dcfg", "syscon"; + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,ls1028a-dcfg", "syscon", "simple-mfd"; reg = <0x0 0x1e00000 0x0 0x10000>; + ranges = <0x0 0x0 0x1e00000 0x10000>; little-endian; + + fspi_clk: clock-controller@900 { + compatible = "fsl,ls1028a-flexspi-clk"; + reg = <0x900 0x4>; + #clock-cells = <0>; + clocks = <&clockgen QORIQ_CLK_HWACCEL 0>; + clock-output-names = "fspi_clk"; + }; }; rst: syscon@1e60000 {
@@ -327,8 +338,7 @@ <0x0 0x20000000 0x0 0x10000000>; reg-names = "fspi_base", "fspi_mmap"; interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen QORIQ_CLK_HWACCEL 0>, - <&clockgen QORIQ_CLK_HWACCEL 0>; + clocks = <&fspi_clk>, <&fspi_clk>; clock-names = "fspi_en", "fspi"; status = "disabled"; };
Signature · 1 line
2.20.1
RFC PATCH v3 9/9 arm64: dts: lx2160a: fix FlexSPI clock
In reply to Michael WalleNow that we have a proper driver for the FlexSPI interface use it. This will fix SCK frequency switching on Layerscape SoCs.
---
Thanks to Vladimir Oltean, this was partially tested on a LX2160A RDB. But this patch is marked as RFC nonetheless, because there is too much difference in the clock tree between LS1028A and LX2160A. It would be nice if someone could test it and add a Tested-by.
Changes since v2:
- none
Changes since v1:
- none
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi | 15 +++++++++++++-- 1 file changed, 13 insertions(+), 2 deletions(-)
arch/arm64/boot/dts/freescale/fsl-lx2160a.dtsi +13 -2
@@ -661,9 +661,20 @@ }; dcfg: syscon@1e00000 { - compatible = "fsl,lx2160a-dcfg", "syscon"; + #address-cells = <1>; + #size-cells = <1>; + compatible = "fsl,lx2160a-dcfg", "syscon", "simple-mfd"; reg = <0x0 0x1e00000 0x0 0x10000>; + ranges = <0x0 0x0 0x1e00000 0x10000>; little-endian; + + fspi_clk: clock-controller@900 { + compatible = "fsl,lx2160a-flexspi-clk"; + reg = <0x900 0x4>; + #clock-cells = <0>; + clocks = <&clockgen 4 0>; + clock-output-names = "fspi_clk"; + }; }; tmu: tmu@1f80000 {
@@ -778,7 +789,7 @@ <0x0 0x20000000 0x0 0x10000000>; reg-names = "fspi_base", "fspi_mmap"; interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; - clocks = <&clockgen 4 3>, <&clockgen 4 3>; + clocks = <&clockgen 4 3>, <&fspi_clk>; clock-names = "fspi_en", "fspi"; status = "disabled"; };
Signature · 1 line
2.20.1
Re: [RFC PATCH v3 9/9] arm64: dts: lx2160a: fix FlexSPI clock
Quoted 9 lines · Michael Walle
Now that we have a proper driver for the FlexSPI interface use it. This will fix SCK frequency switching on Layerscape SoCs.
Signed-off-by Michael Walle <[email protected]>---
Thanks to Vladimir Oltean, this was partially tested on a LX2160A RDB. But this patch is marked as RFC nonetheless, because there is too much difference in the clock tree between LS1028A and LX2160A. It would be nice if someone could test it and add a Tested-by.
You want someone to probe the SCK frequency? I expect that if frequency switching works on LS1028A, and the lx2160a_flexspi_divs table is correct (which, based on the documentation for FlexSPICR1[FlexSPI_CLK_DIV], it is), then it would work on LX2160A too?
Is there a simple test that can be made in order to trivially determine whether the frequencies are correct?
Re: [RFC PATCH v3 9/9] arm64: dts: lx2160a: fix FlexSPI clock
Am 2020-11-08 22:21, schrieb Vladimir Oltean:
Quoted 12 lines · Michael Walle
Quoted 9 lines
Now that we have a proper driver for the FlexSPI interface use it. This will fix SCK frequency switching on Layerscape SoCs.
Signed-off-by Michael Walle <[email protected]>---
Thanks to Vladimir Oltean, this was partially tested on a LX2160A RDB. But this patch is marked as RFC nonetheless, because there is too much difference in the clock tree between LS1028A and LX2160A. It would be nice if someone could test it and add a Tested-by.You want someone to probe the SCK frequency?
No not really, just a thorough test.
Quoted 4 lines
I expect that if frequency
switching works on LS1028A, and thelx2160a_flexspi_divstable is correct (which, based on the documentation for FlexSPICR1[FlexSPI_CLK_DIV], it is), then it would work on LX2160A too?
The switching should work. Finding out wether it is correct can be checked by reading the raw register value, i.e. 01E0_0900h. But the parent clock is what is bothering me a little. Getting that wrong would lead to a wrong SCK output frequency albeit the divider is set to a correct value.
Quoted 2 lines
Is there a simple test that can be made in order to trivially determine whether the frequencies are correct?
We already found out that there seems to be kind of a saturation with higher frequencies, i.e. octal SPI bus is capable of a much higher throughput but we only achieve 50MB/s. I'd have expected a much higher datarate (I mean it is advertised as high performance and it uses a 8 bit wide databus..). But anyway, it might make sense to go the other way, i.e. find out the max datathroughput at lower frequencies and look if it makes sense. Assuming no DDR, the throughput should be around your frequency. For example, having 4 MHz should result in 4MB/s data throughput.
OTOH we already saw that after linux booted - with the current device tree which has a setting of 50MHz max SCK frequency - the programmed divider by my driver is the same as the former setting (0x13, div-by-32); so this series doesn't change the SCK frequency.
-michael