Skip to contentSkip to conversation

doc: fix testpmd sample qinq flow rules

PATCH Applied Bernard Iremonger 3 participants 3 messages Jan 19, 2021 – Feb 2, 2021 1 message not in the archive

lore
Share & tools
lore

A message that is not in the archive (sent off-list or not yet received): 1610623187-3631-1

#1 lore raw

PATCH v2 1/1 doc: fix testpmd sample qinq flow rules

In the Testpmd Flow rules management section, correct the TPID values in the Sample QinQ flow rules sub section. Also replace the keyword qinq_strip with extend in the vlan set command.

Fixes bef3bfe7d5f4 ("doc: revise sample testpmd flow commands")
---
 doc/guides/testpmd_app_ug/testpmd_funcs.rst | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
doc/guides/testpmd_app_ug/testpmd_funcs.rst +3 -3
index 9be4500..6a00245 100644
@@ -4426,14 +4426,14 @@ Sample QinQ flow rules
 Before creating QinQ rule(s) the following commands should be issued to enable QinQ::
 
    testpmd> port stop 0
-   testpmd> vlan set qinq_strip on 0
+   testpmd> vlan set extend on 0
 
 The above command sets the inner and outer TPID's to 0x8100.
 
 To change the TPID's the following commands should be used::
 
-   testpmd> vlan set outer tpid 0xa100 0
-   testpmd> vlan set inner tpid 0x9100 0
+   testpmd> vlan set outer tpid 0x88A8 0
+   testpmd> vlan set inner tpid 0x8100 0
    testpmd> port start 0
 
 Validate and create a QinQ rule on port 0 to steer traffic to a VF queue in a VM.
Signature · 1 line
2.7.4
Acked-by on v2 1/1
#2 lore raw
Quoted 44 lines

-----Original Message-----
From: Iremonger, Bernard <[email protected]>
Sent: Tuesday, January 19, 2021 21:01
To: [email protected]; Li, Xiaoyun <[email protected]>
Cc: Iremonger, Bernard <[email protected]>; [email protected]
Subject: [PATCH v2] doc: fix testpmd sample qinq flow rules

In the Testpmd Flow rules management section, correct the TPID values in the Sample QinQ flow rules sub section.
Also replace the keyword qinq_strip with extend in the vlan set command.

Fixes bef3bfe7d5f4 ("doc: revise sample testpmd flow commands")
---
 doc/guides/testpmd_app_ug/testpmd_funcs.rst | 6 +++---
 1 file changed, 3 insertions(+), 3 deletions(-)
doc/guides/testpmd_app_ug/testpmd_funcs.rst +0 -0
index 9be4500..6a00245 100644
@@ -4426,14 +4426,14 @@ Sample QinQ flow rules  Before creating QinQ

rule(s) the following commands should be issued to enable QinQ::

testpmd> port stop 0

doc/guides/testpmd_app_ug/testpmd_funcs.rst +3 -4
-   testpmd> vlan set qinq_strip on 0
+   testpmd> vlan set extend on 0
 
 The above command sets the inner and outer TPID's to 0x8100.
 
 To change the TPID's the following commands should be used::
 
-   testpmd> vlan set outer tpid 0xa100 0
-   testpmd> vlan set inner tpid 0x9100 0
+   testpmd> vlan set outer tpid 0x88A8 0
+   testpmd> vlan set inner tpid 0x8100 0
    testpmd> port start 0
 
 Validate and create a QinQ rule on port 0 to steer traffic to a VF queue in a VM.
--

2.7.4

Applied
#3 lore raw
Quoted 11 lines · Xiaoyun
Quoted 11 lines

-----Original Message-----
From: Iremonger, Bernard <[email protected]>
Sent: Tuesday, January 19, 2021 21:01
To: [email protected]; Li, Xiaoyun <[email protected]>
Cc: Iremonger, Bernard <[email protected]>; [email protected]
Subject: [PATCH v2] doc: fix testpmd sample qinq flow rules

In the Testpmd Flow rules management section, correct the TPID values in the Sample QinQ flow rules sub section.
Also replace the keyword qinq_strip with extend in the vlan set command.

Quoted 7 lines
Quoted 4 lines
Fixes bef3bfe7d5f4 ("doc: revise sample testpmd flow commands")

Applied to dpdk-next-net/main, thanks.