Kconfig restyle part 2
Subsystems (46)
cover Kconfig restyle part 2
The Kconfig menu attribute '---help---' is deprecated. If we change to "help" the text has to indent. This again has to align with other attributes, so we have to restyle them as well.
And as there's a script then change all Kconfig files excluding 'arch' and 'board' directories from part 1.
Restyle all Kconfigs:
Menu entries : no space left
Menu attributes: 1 TAB
Help text : 1 TAB + 2 spaces
Replace '---help---' by 'help'
Problems:
People creating indents in help texts.
The script doesn't care. It puts everything left aligned.
Help texts with empty lines. It stops aligning as help test.
Other fixes:
While using checkpatch.pl or the script some issues showed up, so fix them as well.
Johan Jonker (18):
Kconfig: boot: restyle
Kconfig: cmd: restyle
Kconfig: common: restyle
Kconfig: disk: restyle
Kconfig: dts: restyle
Kconfig: fs: restyle
Kconfig: lib: restyle
Kconfig: net: restyle
Kconfig: i2c: restyle
Kconfig: mtd: restyle
Kconfig: net: restyle
Kconfig: pinctrl: restyle
Kconfig: power: restyle
Kconfig: usb: restyle
Kconfig: video: restyle
Kconfig: gpio: add empty line
Kconfig: drivers: restyle remaining
Kconfig: restyle
Kconfig | 14 +- boot/Kconfig | 10 +- cmd/Kconfig | 74 +++--- cmd/ti/Kconfig | 18 +- common/Kconfig | 8 +- common/spl/Kconfig | 34 +-- disk/Kconfig | 6 +- drivers/adc/Kconfig | 2 +- drivers/block/Kconfig | 8 +- drivers/bootcount/Kconfig | 4 +- drivers/clk/Kconfig | 4 +- drivers/clk/owl/Kconfig | 8 +- drivers/clk/renesas/Kconfig | 8 +- drivers/crypto/aspeed/Kconfig | 4 +- drivers/crypto/fsl/Kconfig | 10 +- drivers/ddr/fsl/Kconfig | 4 +- drivers/dma/ti/Kconfig | 16 +- drivers/gpio/Kconfig | 49 ++-- drivers/i2c/Kconfig | 140 +++++------ drivers/i2c/muxes/Kconfig | 2 +- drivers/led/Kconfig | 2 +- drivers/memory/Kconfig | 16 +- drivers/mfd/Kconfig | 6 +- drivers/misc/Kconfig | 8 +- drivers/mmc/Kconfig | 8 +- drivers/mtd/Kconfig | 20 +- drivers/mtd/nand/raw/Kconfig | 70 +++--- drivers/mtd/spi/Kconfig | 54 ++--- drivers/mtd/ubi/Kconfig | 4 +- drivers/mux/Kconfig | 12 +- drivers/net/Kconfig | 48 ++-- drivers/net/phy/Kconfig | 18 +- drivers/net/ti/Kconfig | 4 +- drivers/pci/Kconfig | 16 +- drivers/pci_endpoint/Kconfig | 8 +- drivers/phy/Kconfig | 14 +- drivers/phy/qcom/Kconfig | 2 +- drivers/pinctrl/broadcom/Kconfig | 8 +- drivers/pinctrl/mediatek/Kconfig | 2 +- drivers/pinctrl/mscc/Kconfig | 20 +- drivers/pinctrl/mvebu/Kconfig | 12 +- drivers/pinctrl/qcom/Kconfig | 10 +- drivers/power/Kconfig | 364 ++++++++++++++-------------- drivers/power/domain/Kconfig | 8 +- drivers/power/pmic/Kconfig | 348 +++++++++++++-------------- drivers/power/regulator/Kconfig | 398 +++++++++++++++---------------- drivers/ram/aspeed/Kconfig | 10 +- drivers/ram/octeon/Kconfig | 6 +- drivers/ram/stm32mp1/Kconfig | 36 +-- drivers/reboot-mode/Kconfig | 18 +- drivers/rtc/Kconfig | 4 +- drivers/serial/Kconfig | 16 +- drivers/smem/Kconfig | 30 +-- drivers/soc/ti/Kconfig | 4 +- drivers/spi/Kconfig | 28 +-- drivers/spmi/Kconfig | 8 +- drivers/thermal/Kconfig | 32 +-- drivers/ufs/Kconfig | 4 +- drivers/usb/Kconfig | 16 +- drivers/usb/eth/Kconfig | 16 +- drivers/usb/gadget/Kconfig | 22 +- drivers/usb/host/Kconfig | 44 ++-- drivers/usb/musb-new/Kconfig | 14 +- drivers/video/Kconfig | 178 +++++++------- drivers/video/bridge/Kconfig | 4 +- drivers/video/imx/Kconfig | 2 +- drivers/video/rockchip/Kconfig | 4 +- drivers/video/tegra/Kconfig | 42 ++-- drivers/video/ti/Kconfig | 2 +- drivers/video/zynqmp/Kconfig | 6 +- drivers/watchdog/Kconfig | 8 +- dts/Kconfig | 26 +- fs/fat/Kconfig | 2 +- lib/rsa/Kconfig | 8 +- net/Kconfig | 20 +- net/lwip/Kconfig | 2 +- 76 files changed, 1258 insertions(+), 1257 deletions(-)
--
2.39.5
PATCH 1/18 Kconfig: boot: restyle
Restyle all Kconfigs for "boot":
Menu entries : no space left
Menu attributes: 1 TAB
Help text : 1 TAB + 2 spaces
Replace '---help---' by 'help'
--- boot/Kconfig | 10 +++++----- 1 file changed, 5 insertions(+), 5 deletions(-)
boot/Kconfig +5 -5
@@ -653,9 +653,9 @@ config BOOTMETH_QFW depends on QFW default y help - Use QEMU parameters -kernel, -initrd, -append to determine the kernel, - initial RAM disk, and kernel command line parameters to boot an - operating system. U-Boot's control device-tree is passed to the kernel. + Use QEMU parameters -kernel, -initrd, -append to determine the kernel, + initial RAM disk, and kernel command line parameters to boot an + operating system. U-Boot's control device-tree is passed to the kernel. config BOOTMETH_VBE bool "Bootdev support for Verified Boot for Embedded"
@@ -1051,7 +1051,7 @@ config MEASURED_BOOT to use some attestation tools on your system. if MEASURED_BOOT - config MEASURE_DEVICETREE +config MEASURE_DEVICETREE bool "Measure the devicetree image" default y if MEASURED_BOOT help
@@ -1060,7 +1060,7 @@ if MEASURED_BOOT Therefore, it should not be measured into the TPM. In that case, disable the measurement here. - config MEASURE_IGNORE_LOG +config MEASURE_IGNORE_LOG bool "Ignore the existing event log" help On platforms that use an event log memory region that persists
--
2.39.5
PATCH 2/18 Kconfig: cmd: restyle
In reply to Johan JonkerRestyle all Kconfigs for "cmd":
Menu entries : no space left
Menu attributes: 1 TAB
Help text : 1 TAB + 2 spaces
Replace '---help---' by 'help'
--- cmd/Kconfig | 74 +++++++++++++++++++++++++------------------------- cmd/ti/Kconfig | 18 ++++++------ 2 files changed, 46 insertions(+), 46 deletions(-)
cmd/Kconfig +37 -37
@@ -881,12 +881,12 @@ config EEPROM_LAYOUT_VERSIONS via the -l option. config EEPROM_LAYOUT_HELP_STRING - string "Tells user what layout names are supported" - depends on EEPROM_LAYOUT_VERSIONS - default "<not defined>" - help - Help printed with the LAYOUT VERSIONS part of the 'eeprom' - command's help. + string "Tells user what layout names are supported" + depends on EEPROM_LAYOUT_VERSIONS + default "<not defined>" + help + Help printed with the LAYOUT VERSIONS part of the 'eeprom' + command's help. config SYS_I2C_EEPROM_BUS int "I2C bus of the EEPROM device."
@@ -967,14 +967,14 @@ config CMD_MEMORY default y help Memory commands. - md - memory display - mm - memory modify (auto-incrementing address) - nm - memory modify (constant address) - mw - memory write (fill) - cp - memory copy - cmp - memory compare - base - print or set address offset - loop - initialize loop on address range + md - memory display + mm - memory modify (auto-incrementing address) + nm - memory modify (constant address) + mw - memory write (fill) + cp - memory copy + cmp - memory compare + base - print or set address offset + loop - initialize loop on address range config CMD_MEM_SEARCH bool "ms - Memory search"
@@ -1115,9 +1115,9 @@ config CMD_ARMFFA help Provides a test command for the FF-A support supported options: - - Listing the partition(s) info - - Sending a data pattern to the specified partition - - Displaying the arm_ffa device info + - Listing the partition(s) info + - Sending a data pattern to the specified partition + - Displaying the arm_ffa device info config CMD_ARMFLASH bool "armflash"
@@ -1214,9 +1214,9 @@ config CMD_FLASH depends on FLASH_CFI_DRIVER || MTD_NOR_FLASH help NOR flash support. - flinfo - print FLASH memory information - erase - FLASH memory - protect - enable or disable FLASH write protection + flinfo - print FLASH memory information + erase - FLASH memory + protect - enable or disable FLASH write protection config CMD_FPGA bool "fpga"
@@ -1548,7 +1548,7 @@ config CMD_OPTEE bool "Enable OP-TEE commands" depends on OPTEE help - OP-TEE commands support. + OP-TEE commands support. config CMD_MTD bool "mtd"
@@ -1606,7 +1606,7 @@ config CMD_MUX bool "mux" depends on MULTIPLEXER help - List, select, and deselect mux controllers on the fly. + List, select, and deselect mux controllers on the fly. config CMD_NAND bool "nand"
@@ -1814,7 +1814,7 @@ config CMD_UFS depends on UFS help "This provides commands to initialise and configure universal flash - subsystem devices" + subsystem devices" config CMD_USB bool "usb"
@@ -1936,7 +1936,7 @@ config CMD_SETEXPR default y help Evaluate boolean and math expressions and store the result in an env - variable. + variable. Also supports loading the value at a memory location into a variable. If CONFIG_REGEX is enabled, setexpr also supports a gsub function.
@@ -2642,9 +2642,9 @@ config CMD_PSTORE_ECC_SIZE depends on CMD_PSTORE default "0" help - if non-zero, the option enables ECC support and specifies ECC buffer - size in bytes (1 is a special value, means 16 bytes ECC), should be - identical to ramoops.ramoops_ecc parameter used by kernel + if non-zero, the option enables ECC support and specifies ECC buffer + size in bytes (1 is a special value, means 16 bytes ECC), should be + identical to ramoops.ramoops_ecc parameter used by kernel endif
@@ -3156,15 +3156,15 @@ config CMD_AVB help Enables a "avb" command to perform verification of partitions using Android Verified Boot 2.0 functionality. It includes such subcommands: - avb init - initialize avb2 subsystem - avb read_rb - read rollback index - avb write_rb - write rollback index - avb is_unlocked - check device lock state - avb get_uuid - read and print uuid of a partition - avb read_part - read data from partition - avb read_part_hex - read data from partition and output to stdout - avb write_part - write data to partition - avb verify - run full verification chain + avb init - initialize avb2 subsystem + avb read_rb - read rollback index + avb write_rb - write rollback index + avb is_unlocked - check device lock state + avb get_uuid - read and print uuid of a partition + avb read_part - read data from partition + avb read_part_hex - read data from partition and output to stdout + avb write_part - write data to partition + avb verify - run full verification chain config CMD_STACKPROTECTOR_TEST bool "Test command for stack protector"
@@ -3194,7 +3194,7 @@ config CMD_UBI_RENAME depends on CMD_UBI help Enable a "ubi" command to rename ubi volume: - ubi rename <oldname> <newname> + ubi rename <oldname> <newname> config CMD_UBIFS tristate "Enable UBIFS - Unsorted block images filesystem commands"
cmd/ti/Kconfig +9 -9
@@ -4,24 +4,24 @@ config CMD_DDR3 bool "command for verifying DDR features" depends on ARCH_KEYSTONE || DRA7XX help - Support for testing ddr3 on TI platforms. This command - supports memory verification, memory comapre and ecc - verification if supported. + Support for testing ddr3 on TI platforms. This command + supports memory verification, memory comapre and ecc + verification if supported. config CMD_DDR4 bool "command for verifying DDRSS Inline ECC features" depends on ARCH_K3 help - Support for testing DDRSS on TI platforms. This command supports - memory verification, memory compare and inline ECC verification - if supported. + Support for testing DDRSS on TI platforms. This command supports + memory verification, memory compare and inline ECC verification + if supported. config CMD_PD bool "command for verifying power domains" depends on TI_POWER_DOMAIN help - Debug command for K3 power domains. For this to work, the - K3 power domain driver must be enabled for the u-boot; by - default it is only enabled for SPL. + Debug command for K3 power domains. For this to work, the + K3 power domain driver must be enabled for the u-boot; by + default it is only enabled for SPL. endmenu
--
2.39.5
PATCH 3/18 Kconfig: common: restyle
In reply to Johan JonkerRestyle all Kconfigs for "common":
Menu entries : no space left
Menu attributes: 1 TAB
Help text : 1 TAB + 2 spaces
Replace '---help---' by 'help'
--- common/Kconfig | 8 ++++---- common/spl/Kconfig | 34 +++++++++++++++++----------------- 2 files changed, 21 insertions(+), 21 deletions(-)
common/Kconfig +4 -4
@@ -78,7 +78,7 @@ config SYS_PBSIZE config DISABLE_CONSOLE bool "Add functionality to disable console completely" help - Disable console (in & out). + Disable console (in & out). config IDENT_STRING string "Board specific string to be added to uboot version string"
@@ -884,9 +884,9 @@ config AVB_VERIFY help This option enables compilation of bootloader-dependent operations, used by Android Verified Boot 2.0 library (libavb). Includes: - * Helpers to process strings in order to build OS bootargs. - * Helpers to access MMC, similar to drivers/fastboot/fb_mmc.c. - * Helpers to alloc/init/free avb ops. + * Helpers to process strings in order to build OS bootargs. + * Helpers to access MMC, similar to drivers/fastboot/fb_mmc.c. + * Helpers to alloc/init/free avb ops. if AVB_VERIFY
common/spl/Kconfig +17 -17
@@ -1321,10 +1321,10 @@ config SPL_PCI config SPL_PCI_ENDPOINT bool "Support for PCI endpoint drivers" help - Enable this configuration option to support configurable PCI - endpoints at SPL. This should be enabled if the platform has - a PCI controllers that can operate in endpoint mode (as a device - connected to PCI host or bridge). + Enable this configuration option to support configurable PCI + endpoints at SPL. This should be enabled if the platform has + a PCI controllers that can operate in endpoint mode (as a device + connected to PCI host or bridge). config SPL_PCH bool "Support PCH drivers"
@@ -1552,18 +1552,18 @@ config SPL_SPI_FLASH_TINY depends on !SPI_FLASH_BAR default y if SPI_FLASH help - Enable lightweight SPL SPI Flash support that supports just reading - data/images from flash. No support to write/erase flash. Enable - this if you have SPL size limitations and don't need full - fledged SPI flash support. + Enable lightweight SPL SPI Flash support that supports just reading + data/images from flash. No support to write/erase flash. Enable + this if you have SPL size limitations and don't need full + fledged SPI flash support. config SPL_SPI_FLASH_SFDP_SUPPORT bool "SFDP table parsing support for SPI NOR flashes" depends on !SPI_FLASH_BAR && !SPL_SPI_FLASH_TINY help - Enable support for parsing and auto discovery of parameters for - SPI NOR flashes using Serial Flash Discoverable Parameters (SFDP) - tables as per JESD216 standard in SPL. + Enable support for parsing and auto discovery of parameters for + SPI NOR flashes using Serial Flash Discoverable Parameters (SFDP) + tables as per JESD216 standard in SPL. config SPL_SPI_FLASH_MTD bool "Support for SPI flash MTD drivers in SPL"
@@ -1584,22 +1584,22 @@ config SYS_SPI_U_BOOT_OFFS default 0x0 depends on SPL_SPI_LOAD || SPL_SPI_SUNXI help - Address within SPI-Flash from where the u-boot payload is fetched - from. + Address within SPI-Flash from where the u-boot payload is fetched + from. config SYS_SPI_KERNEL_OFFS hex "Falcon mode: address of kernel payload in SPI flash" depends on SPL_SPI_FLASH_SUPPORT && SPL_OS_BOOT help - Address within SPI-Flash from where the kernel payload is fetched - in falcon boot. + Address within SPI-Flash from where the kernel payload is fetched + in falcon boot. config SYS_SPI_ARGS_OFFS hex "Falcon mode: address of args payload in SPI flash" depends on SPL_SPI_FLASH_SUPPORT && SPL_OS_BOOT_ARGS help - Address within SPI-Flash from where the args payload (usually the - dtb) is fetched in falcon boot. + Address within SPI-Flash from where the args payload (usually the + dtb) is fetched in falcon boot. config SYS_SPI_ARGS_SIZE hex "Falcon mode: size of args payload in SPI flash"
--
2.39.5
PATCH 4/18 Kconfig: disk: restyle
In reply to Johan JonkerRestyle all Kconfigs for "disk":
Menu entries : no space left
Menu attributes: 1 TAB
Help text : 1 TAB + 2 spaces
Replace '---help---' by 'help'
--- disk/Kconfig | 6 +++--- 1 file changed, 3 insertions(+), 3 deletions(-)
disk/Kconfig +3 -3
@@ -8,11 +8,11 @@ config PARTITIONS Zero or more of the following: - CONFIG_MAC_PARTITION Apple's MacOS partition table. - CONFIG_DOS_PARTITION MS Dos partition table, traditional on the - Intel architecture, USB sticks, etc. + Intel architecture, USB sticks, etc. - CONFIG_ISO_PARTITION ISO partition table, used on CDROM etc. - CONFIG_EFI_PARTITION GPT partition table, common when EFI is the - bootloader. Note 2TB partition limit; see - disk/part_efi.c + bootloader. Note 2TB partition limit; see + disk/part_efi.c - CONFIG_MTD_PARTITIONS Memory Technology Device partition table. If IDE or SCSI support is enabled (CONFIG_CMD_IDE or CONFIG_SCSI) you must configure support for at least one non-MTD partition type
--
2.39.5
PATCH 5/18 Kconfig: dts: restyle
In reply to Johan JonkerRestyle all Kconfigs for "dts":
Menu entries : no space left
Menu attributes: 1 TAB
Help text : 1 TAB + 2 spaces
Replace '---help---' by 'help'
--- dts/Kconfig | 26 +++++++++++++------------- 1 file changed, 13 insertions(+), 13 deletions(-)
dts/Kconfig +13 -13
@@ -224,7 +224,7 @@ config DEFAULT_DEVICE_TREE $ make DEVICE_TREE=<device-tree-name> config DEVICE_TREE_INCLUDES - string "Extra .dtsi files to include when building DT control" + string "Extra .dtsi files to include when building DT control" depends on OF_CONTROL help U-Boot's control .dtb is usually built from an in-tree .dts
@@ -297,17 +297,17 @@ config MULTI_DTB_FIT_UNCOMPRESS_SZ hex "Size of memory reserved to uncompress the DTBs" default 0x8000 help - This is the size of this area where the DTBs are uncompressed. - If this area is dynamically allocated, make sure that - SYS_MALLOC_F_LEN is big enough to contain it. + This is the size of this area where the DTBs are uncompressed. + If this area is dynamically allocated, make sure that + SYS_MALLOC_F_LEN is big enough to contain it. config MULTI_DTB_FIT_USER_DEF_ADDR hex "Address of memory where dtbs are uncompressed" depends on MULTI_DTB_FIT_USER_DEFINED_AREA help - the FIT image containing the DTBs is uncompressed in an area defined - at compilation time. This is the address of this area. It must be - aligned on 2-byte boundary. + the FIT image containing the DTBs is uncompressed in an area defined + at compilation time. This is the address of this area. It must be + aligned on 2-byte boundary. config DTB_RESELECT bool "Support swapping dtbs at a later point in boot"
@@ -398,17 +398,17 @@ config SPL_MULTI_DTB_FIT_UNCOMPRESS_SZ depends on (SPL_MULTI_DTB_FIT_GZIP || SPL_MULTI_DTB_FIT_LZO) default 0x8000 help - This is the size of this area where the DTBs are uncompressed. - If this area is dynamically allocated, make sure that - SPL_SYS_MALLOC_F_LEN is big enough to contain it. + This is the size of this area where the DTBs are uncompressed. + If this area is dynamically allocated, make sure that + SPL_SYS_MALLOC_F_LEN is big enough to contain it. config SPL_MULTI_DTB_FIT_USER_DEF_ADDR hex "Address of memory where dtbs are uncompressed" depends on SPL_MULTI_DTB_FIT_USER_DEFINED_AREA help - the FIT image containing the DTBs is uncompressed in an area defined - at compilation time. This is the address of this area. It must be - aligned on 2-byte boundary. + the FIT image containing the DTBs is uncompressed in an area defined + at compilation time. This is the address of this area. It must be + aligned on 2-byte boundary. config OF_SPL_REMOVE_PROPS string "List of device tree properties to drop for SPL"
--
2.39.5
PATCH 6/18 Kconfig: fs: restyle
In reply to Johan JonkerRestyle all Kconfigs for "fs":
Menu entries : no space left
Menu attributes: 1 TAB
Help text : 1 TAB + 2 spaces
Replace '---help---' by 'help'
--- fs/fat/Kconfig | 2 +- 1 file changed, 1 insertion(+), 1 deletion(-)
fs/fat/Kconfig +1 -1
@@ -36,4 +36,4 @@ config FS_FAT_HANDLE_SECTOR_SIZE_MISMATCH depends on FS_FAT help Handle filesystems on media where the hardware block size and - the sector size in the FAT metadata do not match. + the sector size in the FAT metadata do not match.
--
2.39.5
PATCH 7/18 Kconfig: lib: restyle
In reply to Johan JonkerRestyle all Kconfigs for "lib":
Menu entries : no space left
Menu attributes: 1 TAB
Help text : 1 TAB + 2 spaces
Replace '---help---' by 'help'
--- lib/rsa/Kconfig | 8 ++++---- 1 file changed, 4 insertions(+), 4 deletions(-)
lib/rsa/Kconfig +4 -4
@@ -94,14 +94,14 @@ config RSA_FREESCALE_EXP bool "Enable RSA Modular Exponentiation with FSL crypto accelerator" depends on DM && FSL_CAAM && !ARCH_MX7 && !ARCH_MX7ULP && !ARCH_MX6 && !ARCH_MX5 help - Enables driver for RSA modular exponentiation using Freescale cryptographic - accelerator - CAAM. + Enables driver for RSA modular exponentiation using Freescale cryptographic + accelerator - CAAM. config RSA_ASPEED_EXP bool "Enable RSA Modular Exponentiation with ASPEED crypto accelerator" depends on DM && ASPEED_ACRY help - Enables driver for RSA modular exponentiation using ASPEED cryptographic - accelerator - ACRY + Enables driver for RSA modular exponentiation using ASPEED cryptographic + accelerator - ACRY endif
--
2.39.5
PATCH 8/18 Kconfig: net: restyle
In reply to Johan JonkerRestyle all Kconfigs for "net":
Menu entries : no space left
Menu attributes: 1 TAB
Help text : 1 TAB + 2 spaces
Replace '---help---' by 'help'
--- net/Kconfig | 20 ++++++++++---------- net/lwip/Kconfig | 2 +- 2 files changed, 11 insertions(+), 11 deletions(-)
net/Kconfig +10 -10
@@ -114,15 +114,15 @@ config SERVERIP_FROM_PROXYDHCP bool "Get serverip value from Proxy DHCP response" help Allows bootfile config to be fetched from Proxy DHCP server - while IP is obtained from main DHCP server. + while IP is obtained from main DHCP server. config SERVERIP_FROM_PROXYDHCP_DELAY_MS int "# of additional milliseconds to wait for ProxyDHCP response" default 100 help Amount of additional time to wait for ProxyDHCP response after - receiving response from main DHCP server. Has no effect if - SERVERIP_FROM_PROXYDHCP is false. + receiving response from main DHCP server. Has no effect if + SERVERIP_FROM_PROXYDHCP is false. config KEEP_SERVERADDR bool "Write the server's MAC address to 'serveraddr'"
@@ -282,10 +282,10 @@ config TFTP_BLOCKSIZE endif # if NET config SYS_RX_ETH_BUFFER - int "Number of receive packet buffers" - default 4 - help - Defines the number of Ethernet receive buffers. On some Ethernet - controllers it is recommended to set this value to 8 or even higher, - since all buffers can be full shortly after enabling the interface on - high Ethernet traffic. + int "Number of receive packet buffers" + default 4 + help + Defines the number of Ethernet receive buffers. On some Ethernet + controllers it is recommended to set this value to 8 or even higher, + since all buffers can be full shortly after enabling the interface on + high Ethernet traffic.
net/lwip/Kconfig +1 -1
@@ -18,7 +18,7 @@ config LWIP_DEBUG bool "Enable debug traces in the lwIP library" help Prints messages to the console regarding network packets that go in - and out of the lwIP library. + and out of the lwIP library. config LWIP_DEBUG_RXTX bool "Dump packets sent and received by lwIP"
--
2.39.5
PATCH 9/18 Kconfig: i2c: restyle
In reply to Johan JonkerRestyle all Kconfigs for "i2c":
Menu entries : no space left
Menu attributes: 1 TAB
Help text : 1 TAB + 2 spaces
Replace '---help---' by 'help'
--- drivers/i2c/Kconfig | 140 +++++++++++++++++++------------------- drivers/i2c/muxes/Kconfig | 2 +- 2 files changed, 71 insertions(+), 71 deletions(-)
drivers/i2c/Kconfig +70 -70
@@ -110,16 +110,16 @@ config I2C_CROS_EC_TUNNEL config I2C_CROS_EC_LDO bool "Provide access to LDOs on the Chrome OS EC" depends on CROS_EC - ---help--- - On many Chromebooks the main PMIC is inaccessible to the AP. This is - often dealt with by using an I2C pass-through interface provided by - the EC. On some unfortunate models (e.g. Spring) the pass-through - is not available, and an LDO message is available instead. This - option enables a driver which provides very basic access to those - regulators, via the EC. We implement this as an I2C bus which - emulates just the TPS65090 messages we know about. This is done to - avoid duplicating the logic in the TPS65090 regulator driver for - enabling/disabling an LDO. + help + On many Chromebooks the main PMIC is inaccessible to the AP. This is + often dealt with by using an I2C pass-through interface provided by + the EC. On some unfortunate models (e.g. Spring) the pass-through + is not available, and an LDO message is available instead. This + option enables a driver which provides very basic access to those + regulators, via the EC. We implement this as an I2C bus which + emulates just the TPS65090 messages we know about. This is done to + avoid duplicating the logic in the TPS65090 regulator driver for + enabling/disabling an LDO. config I2C_SET_DEFAULT_BUS_NUM bool "Set default I2C bus number"
@@ -180,9 +180,9 @@ config SYS_I2C_IPROC Say yes here to to enable the Broadco I2C driver. config SYS_I2C_FSL - bool "Freescale I2C bus driver" - depends on M68K || PPC - help + bool "Freescale I2C bus driver" + depends on M68K || PPC + help Add support for Freescale I2C busses as used on MPC8240, MPC8245, and MPC85xx processors.
@@ -249,14 +249,14 @@ config SYS_I2C_DW_PCI controller. config SYS_I2C_AST2600 - bool "AST2600 I2C Controller" - depends on DM_I2C && ARCH_ASPEED - help - Say yes here to select AST2600 I2C Host Controller. The driver - support AST2600 I2C new mode register. This I2C controller supports: - _Standard-mode (up to 100 kHz) - _Fast-mode (up to 400 kHz) - _Fast-mode Plus (up to 1 MHz) + bool "AST2600 I2C Controller" + depends on DM_I2C && ARCH_ASPEED + help + Say yes here to select AST2600 I2C Host Controller. The driver + support AST2600 I2C new mode register. This I2C controller supports: + _Standard-mode (up to 100 kHz) + _Fast-mode (up to 400 kHz) + _Fast-mode Plus (up to 1 MHz) config SYS_I2C_ASPEED bool "Aspeed I2C Controller"
@@ -333,50 +333,50 @@ if SYS_I2C_MXC && (SYS_I2C_LEGACY || SPL_SYS_I2C_LEGACY) config SYS_I2C_MXC_I2C1 bool "NXP MXC I2C1" help - Add support for NXP MXC I2C Controller 1. - Required for SoCs which have I2C MXC controller 1 eg LS1088A, LS2080A + Add support for NXP MXC I2C Controller 1. + Required for SoCs which have I2C MXC controller 1 eg LS1088A, LS2080A config SYS_I2C_MXC_I2C2 bool "NXP MXC I2C2" help - Add support for NXP MXC I2C Controller 2. - Required for SoCs which have I2C MXC controller 2 eg LS1088A, LS2080A + Add support for NXP MXC I2C Controller 2. + Required for SoCs which have I2C MXC controller 2 eg LS1088A, LS2080A config SYS_I2C_MXC_I2C3 bool "NXP MXC I2C3" help - Add support for NXP MXC I2C Controller 3. - Required for SoCs which have I2C MXC controller 3 eg LS1088A, LS2080A + Add support for NXP MXC I2C Controller 3. + Required for SoCs which have I2C MXC controller 3 eg LS1088A, LS2080A config SYS_I2C_MXC_I2C4 bool "NXP MXC I2C4" help - Add support for NXP MXC I2C Controller 4. - Required for SoCs which have I2C MXC controller 4 eg LS1088A, LS2080A + Add support for NXP MXC I2C Controller 4. + Required for SoCs which have I2C MXC controller 4 eg LS1088A, LS2080A config SYS_I2C_MXC_I2C5 bool "NXP MXC I2C5" help - Add support for NXP MXC I2C Controller 5. - Required for SoCs which have I2C MXC controller 5 eg LX2160A + Add support for NXP MXC I2C Controller 5. + Required for SoCs which have I2C MXC controller 5 eg LX2160A config SYS_I2C_MXC_I2C6 bool "NXP MXC I2C6" help - Add support for NXP MXC I2C Controller 6. - Required for SoCs which have I2C MXC controller 6 eg LX2160A + Add support for NXP MXC I2C Controller 6. + Required for SoCs which have I2C MXC controller 6 eg LX2160A config SYS_I2C_MXC_I2C7 bool "NXP MXC I2C7" help - Add support for NXP MXC I2C Controller 7. - Required for SoCs which have I2C MXC controller 7 eg LX2160A + Add support for NXP MXC I2C Controller 7. + Required for SoCs which have I2C MXC controller 7 eg LX2160A config SYS_I2C_MXC_I2C8 bool "NXP MXC I2C8" help - Add support for NXP MXC I2C Controller 8. - Required for SoCs which have I2C MXC controller 8 eg LX2160A + Add support for NXP MXC I2C Controller 8. + Required for SoCs which have I2C MXC controller 8 eg LX2160A endif if SYS_I2C_MXC_I2C1
@@ -385,13 +385,13 @@ config SYS_MXC_I2C1_SPEED default 40000000 if TARGET_LS2080A_EMU default 100000 help - MXC I2C Channel 1 speed + MXC I2C Channel 1 speed config SYS_MXC_I2C1_SLAVE hex "I2C1 Slave" default 0x0 help - MXC I2C1 Slave + MXC I2C1 Slave endif if SYS_I2C_MXC_I2C2
@@ -400,13 +400,13 @@ config SYS_MXC_I2C2_SPEED default 40000000 if TARGET_LS2080A_EMU default 100000 help - MXC I2C Channel 2 speed + MXC I2C Channel 2 speed config SYS_MXC_I2C2_SLAVE hex "I2C2 Slave" default 0x0 help - MXC I2C2 Slave + MXC I2C2 Slave endif if SYS_I2C_MXC_I2C3
@@ -414,13 +414,13 @@ config SYS_MXC_I2C3_SPEED int "I2C Channel 3 speed" default 100000 help - MXC I2C Channel 3 speed + MXC I2C Channel 3 speed config SYS_MXC_I2C3_SLAVE hex "I2C3 Slave" default 0x0 help - MXC I2C3 Slave + MXC I2C3 Slave endif if SYS_I2C_MXC_I2C4
@@ -428,13 +428,13 @@ config SYS_MXC_I2C4_SPEED int "I2C Channel 4 speed" default 100000 help - MXC I2C Channel 4 speed + MXC I2C Channel 4 speed config SYS_MXC_I2C4_SLAVE hex "I2C4 Slave" default 0x0 help - MXC I2C4 Slave + MXC I2C4 Slave endif if SYS_I2C_MXC_I2C5
@@ -442,13 +442,13 @@ config SYS_MXC_I2C5_SPEED int "I2C Channel 5 speed" default 100000 help - MXC I2C Channel 5 speed + MXC I2C Channel 5 speed config SYS_MXC_I2C5_SLAVE hex "I2C5 Slave" default 0x0 help - MXC I2C5 Slave + MXC I2C5 Slave endif if SYS_I2C_MXC_I2C6
@@ -456,13 +456,13 @@ config SYS_MXC_I2C6_SPEED int "I2C Channel 6 speed" default 100000 help - MXC I2C Channel 6 speed + MXC I2C Channel 6 speed config SYS_MXC_I2C6_SLAVE hex "I2C6 Slave" default 0x0 help - MXC I2C6 Slave + MXC I2C6 Slave endif if SYS_I2C_MXC_I2C7
@@ -470,13 +470,13 @@ config SYS_MXC_I2C7_SPEED int "I2C Channel 7 speed" default 100000 help - MXC I2C Channel 7 speed + MXC I2C Channel 7 speed config SYS_MXC_I2C7_SLAVE hex "I2C7 Slave" default 0x0 help - MXC I2C7 Slave + MXC I2C7 Slave endif if SYS_I2C_MXC_I2C8
@@ -484,13 +484,13 @@ config SYS_MXC_I2C8_SPEED int "I2C Channel 8 speed" default 100000 help - MXC I2C Channel 8 speed + MXC I2C Channel 8 speed config SYS_MXC_I2C8_SLAVE hex "I2C8 Slave" default 0x0 help - MXC I2C8 Slave + MXC I2C8 Slave endif config SYS_I2C_NEXELL
@@ -668,19 +668,19 @@ config SYS_I2C_STM32F7 help Enable this option to add support for STM32 I2C controller introduced with STM32F7/H7 SoCs. This I2C controller supports : - _ Slave and master modes - _ Multimaster capability - _ Standard-mode (up to 100 kHz) - _ Fast-mode (up to 400 kHz) - _ Fast-mode Plus (up to 1 MHz) - _ 7-bit and 10-bit addressing mode - _ Multiple 7-bit slave addresses (2 addresses, 1 with configurable mask) - _ All 7-bit addresses acknowledge mode - _ General call - _ Programmable setup and hold times - _ Easy to use event management - _ Optional clock stretching - _ Software reset + _ Slave and master modes + _ Multimaster capability + _ Standard-mode (up to 100 kHz) + _ Fast-mode (up to 400 kHz) + _ Fast-mode Plus (up to 1 MHz) + _ 7-bit and 10-bit addressing mode + _ Multiple 7-bit slave addresses (2 addresses, 1 with configurable mask) + _ All 7-bit addresses acknowledge mode + _ General call + _ Programmable setup and hold times + _ Easy to use event management + _ Optional clock stretching + _ Software reset config SYS_I2C_SUN6I_P2WI bool "Allwinner sun6i P2WI controller"
@@ -792,10 +792,10 @@ config SYS_I2C_XILINX_XIIC Support for Xilinx AXI I2C controller. config SYS_I2C_IHS - bool "gdsys IHS I2C driver" - depends on DM_I2C - help - Support for gdsys IHS I2C driver on FPGA bus. + bool "gdsys IHS I2C driver" + depends on DM_I2C + help + Support for gdsys IHS I2C driver on FPGA bus. source "drivers/i2c/muxes/Kconfig"
drivers/i2c/muxes/Kconfig +1 -1
@@ -49,7 +49,7 @@ config I2C_MUX_PCA954x MAX7356, MAX7357, MAX7358, MAX7367, MAX7368 and MAX7369 config I2C_MUX_GPIO - tristate "GPIO-based I2C multiplexer" + tristate "GPIO-based I2C multiplexer" depends on I2C_MUX && DM_GPIO select DEVRES help
--
2.39.5
PATCH 10/18 Kconfig: mtd: restyle
In reply to Johan JonkerRestyle all Kconfigs for "mtd":
Menu entries : no space left
Menu attributes: 1 TAB
Help text : 1 TAB + 2 spaces
Replace '---help---' by 'help'
--- drivers/mtd/Kconfig | 20 +++++------ drivers/mtd/nand/raw/Kconfig | 70 ++++++++++++++++++------------------ drivers/mtd/spi/Kconfig | 54 ++++++++++++++-------------- drivers/mtd/ubi/Kconfig | 4 +-- 4 files changed, 74 insertions(+), 74 deletions(-)
drivers/mtd/Kconfig +10 -10
@@ -205,16 +205,16 @@ config HBMC_AM654 bool "HyperBus controller driver for AM65x SoC" depends on MULTIPLEXER && (MUX_MMIO || SPL_MUX_MMIO) help - This is the driver for HyperBus controller on TI's AM65x and - other SoCs + This is the driver for HyperBus controller on TI's AM65x and + other SoCs config STM32_FLASH bool "STM32 MCU Flash driver" depends on ARCH_STM32 select USE_SYS_MAX_FLASH_BANKS help - This is the driver of embedded flash for some STMicroelectronics - STM32 MCU. + This is the driver of embedded flash for some STMicroelectronics + STM32 MCU. config SYS_MAX_FLASH_SECT int "Maximum number of sectors on a flash chip"
@@ -236,17 +236,17 @@ config SYS_MAX_FLASH_BANKS depends on USE_SYS_MAX_FLASH_BANKS default 1 help - Max number of Flash memory banks using by the MTD framework, in the - flash CFI driver and in some other driver to define the flash_info - struct declaration. + Max number of Flash memory banks using by the MTD framework, in the + flash CFI driver and in some other driver to define the flash_info + struct declaration. config SYS_MAX_FLASH_BANKS_DETECT bool "Detection of flash banks number in CFI driver" depends on CFI_FLASH && FLASH_CFI_DRIVER help - This enables detection of number of flash banks in CFI driver, - to reduce the effective number of flash bank, between 0 and - CONFIG_SYS_MAX_FLASH_BANKS + This enables detection of number of flash banks in CFI driver, + to reduce the effective number of flash bank, between 0 and + CONFIG_SYS_MAX_FLASH_BANKS source "drivers/mtd/nand/Kconfig"
drivers/mtd/nand/raw/Kconfig +35 -35
89 lines not on this page · raw message
drivers/mtd/spi/Kconfig +27 -27
113 lines not on this page · raw message
drivers/mtd/ubi/Kconfig +2 -2
@@ -82,8 +82,8 @@ config MTD_UBI_BEB_LIMIT config MTD_UBI_FASTMAP bool "UBI Fastmap (Experimental feature)" help - Important: this feature is experimental so far and the on-flash - format for fastmap may change in the next kernel versions + Important: this feature is experimental so far and the on-flash + format for fastmap may change in the next kernel versions Fastmap is a mechanism which allows attaching an UBI device in nearly constant time. Instead of scanning the whole MTD device it
--
2.39.5
PATCH 11/18 Kconfig: net: restyle
In reply to Johan JonkerRestyle all Kconfigs for "net":
Menu entries : no space left
Menu attributes: 1 TAB
Help text : 1 TAB + 2 spaces
Replace '---help---' by 'help'
--- drivers/net/Kconfig | 48 ++++++++++++++++++++--------------------- drivers/net/phy/Kconfig | 18 ++++++++-------- drivers/net/ti/Kconfig | 4 ++-- 3 files changed, 35 insertions(+), 35 deletions(-)
drivers/net/Kconfig +24 -24
@@ -184,10 +184,10 @@ config CALXEDA_XGMAC config DWC_ETH_XGMAC bool select PHYLIB - help - This driver supports the Synopsys Designware Ethernet XGMAC (10G - Ethernet MAC) IP block. The IP supports many options for bus type, - clocking/reset structure, and feature list. + help + This driver supports the Synopsys Designware Ethernet XGMAC (10G + Ethernet MAC) IP block. The IP supports many options for bus type, + clocking/reset structure, and feature list. config DWC_ETH_XGMAC_SOCFPGA bool "Synopsys DWC Ethernet XGMAC device support for SOCFPGA"
@@ -229,8 +229,8 @@ config DWC_ETH_QOS_ADI bool "Synopsys DWC Ethernet QOS device support for ADI SC59x-64 parts" depends on DWC_ETH_QOS && ARCH_SC5XX help - The Synopsis Designware Ethernet QoS IP block with the specific - configuration used in the ADI ADSP-SC59X 64 bit SoCs + The Synopsis Designware Ethernet QoS IP block with the specific + configuration used in the ADI ADSP-SC59X 64 bit SoCs config DWC_ETH_QOS_IMX bool "Synopsys DWC Ethernet QOS device support for IMX"
@@ -460,9 +460,9 @@ config FSL_FM_10GEC_REGULAR_NOTATION help On SoCs T4240, T2080, LS1043A, etc, the notation between 10GEC and MAC as below: - 10GEC1->MAC9, 10GEC2->MAC10, 10GEC3->MAC1, 10GEC4->MAC2 + 10GEC1->MAC9, 10GEC2->MAC10, 10GEC3->MAC1, 10GEC4->MAC2 While on SoCs T1024, etc, the notation between 10GEC and MAC as below: - 10GEC1->MAC1, 10GEC2->MAC2 + 10GEC1->MAC1, 10GEC2->MAC2 so we introduce CONFIG_FSL_FM_10GEC_REGULAR_NOTATION to identify the new SoCs on which 10GEC enumeration is consistent with MAC enumeration.
@@ -529,7 +529,7 @@ config KSZ9477 config LITEETH bool "LiteX LiteEth Ethernet MAC" help - Driver for the LiteEth Ethernet MAC from LiteX. + Driver for the LiteEth Ethernet MAC from LiteX. config MV88E6XXX bool "Marvell MV88E6xxx Ethernet switch DSA driver"
@@ -701,12 +701,12 @@ config SJA1105 family. These are 5-port devices and are managed over an SPI interface. Probing is handled based on OF bindings. The driver supports the following revisions: - - SJA1105E (Gen. 1, No TT-Ethernet) - - SJA1105T (Gen. 1, TT-Ethernet) - - SJA1105P (Gen. 2, No SGMII, No TT-Ethernet) - - SJA1105Q (Gen. 2, No SGMII, TT-Ethernet) - - SJA1105R (Gen. 2, SGMII, No TT-Ethernet) - - SJA1105S (Gen. 2, SGMII, TT-Ethernet) + - SJA1105E (Gen. 1, No TT-Ethernet) + - SJA1105T (Gen. 1, TT-Ethernet) + - SJA1105P (Gen. 2, No SGMII, No TT-Ethernet) + - SJA1105Q (Gen. 2, No SGMII, TT-Ethernet) + - SJA1105R (Gen. 2, SGMII, No TT-Ethernet) + - SJA1105S (Gen. 2, SGMII, TT-Ethernet) config SMC911X bool "SMSC LAN911x and LAN921x controller driver"
@@ -740,11 +740,11 @@ config SUN4I_EMAC This driver supports the Allwinner based SUN4I Ethernet MAC. config SUN8I_EMAC - bool "Allwinner Sun8i Ethernet MAC support" - select PHYLIB + bool "Allwinner Sun8i Ethernet MAC support" + select PHYLIB select PHY_GIGE - help - This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC. + help + This driver supports the Allwinner based SUN8I/SUN50I Ethernet MAC. It can be found in H3/A64/A83T based SoCs and compatible with both External and Internal PHYs.
@@ -905,7 +905,7 @@ config FEC1_PHY help Define to the hardcoded PHY address which corresponds to the given FEC; i. e. - #define CONFIG_FEC1_PHY 4 + #define CONFIG_FEC1_PHY 4 means that the PHY with address 4 is connected to FEC1 When set to -1, means to probe for first available.
@@ -929,7 +929,7 @@ config FEC2_PHY help Define to the hardcoded PHY address which corresponds to the given FEC; i. e. - #define CONFIG_FEC1_PHY 4 + #define CONFIG_FEC1_PHY 4 means that the PHY with address 4 is connected to FEC1 When set to -1, means to probe for first available.
@@ -1034,7 +1034,7 @@ config MDIO_GPIO_BITBANG bool "GPIO bitbanging MDIO driver" depends on DM_MDIO && DM_GPIO help - Driver for bitbanging MDIO + Driver for bitbanging MDIO config MDIO_MUX_I2CREG bool "MDIO MUX accessed as a register over I2C"
@@ -1080,8 +1080,8 @@ config MDIO_MSCC_MIIM depends on DM_MDIO select REGMAP help - This driver supports MDIO interface found in Microsemi and Microchip - network switches. + This driver supports MDIO interface found in Microsemi and Microchip + network switches. config MDIO_MUX_MMIOREG bool "MDIO MUX accessed as a MMIO register access"
drivers/net/phy/Kconfig +9 -9
@@ -81,7 +81,7 @@ config PHYLIB_10G config PHY_ADIN bool "Analog Devices Industrial Ethernet PHYs" help - Add support for configuring RGMII on Analog Devices ADIN PHYs. + Add support for configuring RGMII on Analog Devices ADIN PHYs. menuconfig PHY_AQUANTIA bool "Aquantia Ethernet PHYs support"
@@ -126,9 +126,9 @@ config SYS_CORTINA_NO_FW_UPLOAD bool "Cortina firmware loading support" depends on PHY_CORTINA help - Cortina phy has provision to store phy firmware in attached dedicated - EEPROM. And boards designed with such EEPROM does not require firmware - upload. + Cortina phy has provision to store phy firmware in attached dedicated + EEPROM. And boards designed with such EEPROM does not require firmware + upload. choice prompt "Location of the Cortina firmware"
@@ -167,7 +167,7 @@ config PHY_CORTINA_ACCESS default y depends on CORTINA_NI_ENET help - Cortina Access Ethernet PHYs init process + Cortina Access Ethernet PHYs init process config PHY_DAVICOM bool "Davicom Ethernet PHYs support"
@@ -317,13 +317,13 @@ config PHY_TERANETICS config PHY_TI bool "Texas Instruments Ethernet PHYs support" - ---help--- + help Adds PHY registration support for TI PHYs. config PHY_TI_DP83867 select PHY_TI bool "Texas Instruments Ethernet DP83867 PHY support" - ---help--- + help Adds support for the TI DP83867 1Gbit PHY. config SPL_PHY_TI_DP83867
@@ -333,13 +333,13 @@ config SPL_PHY_TI_DP83867 config PHY_TI_DP83869 select PHY_TI bool "Texas Instruments Ethernet DP83869 PHY support" - ---help--- + help Adds support for the TI DP83869 1Gbit PHY. config PHY_TI_GENERIC select PHY_TI bool "Texas Instruments Generic Ethernet PHYs support" - ---help--- + help Adds support for Generic TI PHYs that don't need special handling but the PHY name is associated with a PHY ID.
drivers/net/ti/Kconfig +2 -2
@@ -14,7 +14,7 @@ config DRIVER_TI_EMAC bool "TI Davinci EMAC" depends on ARCH_DAVINCI || ARCH_OMAP2PLUS help - Support for davinci emac + Support for davinci emac config DRIVER_TI_EMAC_USE_RMII depends on DRIVER_TI_EMAC
@@ -26,7 +26,7 @@ config DRIVER_TI_KEYSTONE_NET bool "TI Keystone 2 Ethernet" depends on ARCH_KEYSTONE help - This driver supports the TI Keystone 2 Ethernet subsystem + This driver supports the TI Keystone 2 Ethernet subsystem choice prompt "TI Keystone 2 Ethernet NETCP IP revision"
--
2.39.5
PATCH 12/18 Kconfig: pinctrl: restyle
In reply to Johan JonkerRestyle all Kconfigs for "pinctrl":
Menu entries : no space left
Menu attributes: 1 TAB
Help text : 1 TAB + 2 spaces
Replace '---help---' by 'help'
--- drivers/pinctrl/broadcom/Kconfig | 8 ++++---- drivers/pinctrl/mediatek/Kconfig | 2 +- drivers/pinctrl/mscc/Kconfig | 20 ++++++++++---------- drivers/pinctrl/mvebu/Kconfig | 12 ++++++------ drivers/pinctrl/qcom/Kconfig | 10 +++++----- 5 files changed, 26 insertions(+), 26 deletions(-)
drivers/pinctrl/broadcom/Kconfig +4 -4
@@ -3,13 +3,13 @@ config PINCTRL_BCM283X default y bool "Broadcom 283x family pin control driver" help - Support pin multiplexing and pin configuration control on - Broadcom's 283x family of SoCs. + Support pin multiplexing and pin configuration control on + Broadcom's 283x family of SoCs. config PINCTRL_BCM6838 depends on ARCH_BMIPS && PINCTRL_FULL && OF_CONTROL default y bool "Broadcom 6838 family pin control driver" help - Support pin multiplexing and pin configuration control on - Broadcom's 6838 family of SoCs. + Support pin multiplexing and pin configuration control on + Broadcom's 6838 family of SoCs.
drivers/pinctrl/mediatek/Kconfig +1 -1
@@ -59,7 +59,7 @@ config PINCTRL_MT8516 select PINCTRL_MTK config PINCTRL_MT8518 - bool "MT8518 SoC pinctrl driver" + bool "MT8518 SoC pinctrl driver" select PINCTRL_MTK endif
drivers/pinctrl/mscc/Kconfig +10 -10
@@ -10,8 +10,8 @@ config PINCTRL_MSCC_OCELOT default y bool "Microsemi ocelot family pin control driver" help - Support pin multiplexing and pin configuration control on - Microsemi ocelot SoCs. + Support pin multiplexing and pin configuration control on + Microsemi ocelot SoCs. config PINCTRL_MSCC_LUTON depends on SOC_LUTON && PINCTRL_FULL && OF_CONTROL
@@ -19,8 +19,8 @@ config PINCTRL_MSCC_LUTON default y bool "Microsemi luton family pin control driver" help - Support pin multiplexing and pin configuration control on - Microsemi luton SoCs. + Support pin multiplexing and pin configuration control on + Microsemi luton SoCs. config PINCTRL_MSCC_JR2 depends on SOC_JR2 && PINCTRL_FULL && OF_CONTROL
@@ -28,8 +28,8 @@ config PINCTRL_MSCC_JR2 default y bool "Microsemi jr2 family pin control driver" help - Support pin multiplexing and pin configuration control on - Microsemi jr2 SoCs. + Support pin multiplexing and pin configuration control on + Microsemi jr2 SoCs. config PINCTRL_MSCC_SERVALT depends on SOC_SERVALT && PINCTRL_FULL && OF_CONTROL
@@ -37,8 +37,8 @@ config PINCTRL_MSCC_SERVALT default y bool "Microsemi servalt family pin control driver" help - Support pin multiplexing and pin configuration control on - Microsemi servalt SoCs. + Support pin multiplexing and pin configuration control on + Microsemi servalt SoCs. config PINCTRL_MSCC_SERVAL depends on SOC_SERVAL && PINCTRL_FULL && OF_CONTROL
@@ -46,6 +46,6 @@ config PINCTRL_MSCC_SERVAL default y bool "Microsemi serval family pin control driver" help - Support pin multiplexing and pin configuration control on - Microsemi serval SoCs. + Support pin multiplexing and pin configuration control on + Microsemi serval SoCs.
drivers/pinctrl/mvebu/Kconfig +6 -6
@@ -4,22 +4,22 @@ config PINCTRL_ARMADA_38X depends on ARMADA_38X && PINCTRL_FULL bool "Armada 38x pin control driver" help - Support pin multiplexing and pin configuration control on - Marvell's Armada-38x SoC. + Support pin multiplexing and pin configuration control on + Marvell's Armada-38x SoC. config PINCTRL_ARMADA_37XX depends on ARMADA_3700 && PINCTRL_FULL select DEVRES bool "Armada 37xx pin control driver" help - Support pin multiplexing and pin configuration control on - Marvell's Armada-37xx SoC. + Support pin multiplexing and pin configuration control on + Marvell's Armada-37xx SoC. config PINCTRL_ARMADA_8K depends on (ARMADA_8K || ALLEYCAT_5) && PINCTRL_FULL bool "Armada 7k/8k pin control driver" help - Support pin multiplexing and pin configuration control on - Marvell's Armada-8K SoC. + Support pin multiplexing and pin configuration control on + Marvell's Armada-8K SoC. endif
drivers/pinctrl/qcom/Kconfig +5 -5
@@ -79,12 +79,12 @@ config PINCTRL_QCOM_QCS404 as well as the associated GPIO driver. config PINCTRL_QCOM_QCS615 - bool "Qualcomm QCS615 Pinctrl" + bool "Qualcomm QCS615 Pinctrl" default y if PINCTRL_QCOM_GENERIC - select PINCTRL_QCOM - help - Say Y here to enable support for pinctrl on the Snapdragon QCS615 SoC, - as well as the associated GPIO driver. + select PINCTRL_QCOM + help + Say Y here to enable support for pinctrl on the Snapdragon QCS615 SoC, + as well as the associated GPIO driver. config PINCTRL_QCOM_SA8775P bool "Qualcomm SA8775P Pinctrl"
--
2.39.5
PATCH 13/18 Kconfig: power: restyle
In reply to Johan JonkerRestyle all Kconfigs for "power":
Menu entries : no space left
Menu attributes: 1 TAB
Help text : 1 TAB + 2 spaces
Replace '---help---' by 'help'
--- drivers/power/Kconfig | 364 ++++++++++++++--------------- drivers/power/domain/Kconfig | 8 +- drivers/power/pmic/Kconfig | 348 ++++++++++++++-------------- drivers/power/regulator/Kconfig | 398 ++++++++++++++++---------------- 4 files changed, 559 insertions(+), 559 deletions(-)
drivers/power/Kconfig +182 -182
@@ -1,7 +1,7 @@ menuconfig POWER - bool "Power" - default y - help + bool "Power" + default y + help Enable support for power control in U-Boot. This includes support for PMICs (Power-management Integrated Circuits) and some of the features provided by PMICs. In particular, voltage regulators can
@@ -63,98 +63,98 @@ choice config SUNXI_NO_PMIC bool "board without a pmic" - ---help--- - Select this for boards which do not use a PMIC. + help + Select this for boards which do not use a PMIC. config AXP152_POWER bool "axp152 pmic support" depends on MACH_SUN5I select AXP_PMIC_BUS select CMD_POWEROFF - ---help--- - Select this to enable support for the axp152 pmic found on most - A10s boards. + help + Select this to enable support for the axp152 pmic found on most + A10s boards. config AXP209_POWER bool "axp209 pmic support" depends on MACH_SUN4I || MACH_SUN5I || MACH_SUN7I || MACH_SUN8I_V3S select AXP_PMIC_BUS select CMD_POWEROFF - ---help--- - Select this to enable support for the axp209 pmic found on most - A10, A13 and A20 boards. + help + Select this to enable support for the axp209 pmic found on most + A10, A13 and A20 boards. config AXP221_POWER bool "axp221 / axp223 pmic support" depends on MACH_SUN6I || MACH_SUN8I_A23 || MACH_SUN8I_A33 || MACH_SUN8I_R40 select AXP_PMIC_BUS select CMD_POWEROFF - ---help--- - Select this to enable support for the axp221/axp223 pmic found on most - A23 and A31 boards. + help + Select this to enable support for the axp221/axp223 pmic found on most + A23 and A31 boards. config AXP305_POWER bool "axp305 pmic support" depends on MACH_SUN50I_H616 select AXP_PMIC_BUS select CMD_POWEROFF - ---help--- - Select this to enable support for the axp305 pmic found on most - H616 boards. + help + Select this to enable support for the axp305 pmic found on most + H616 boards. config AXP313_POWER bool "axp313 pmic support" depends on MACH_SUN50I_H616 select AXP_PMIC_BUS select CMD_POWEROFF - ---help--- - Select this to enable support for the AXP313 PMIC found on some - H616 boards. + help + Select this to enable support for the AXP313 PMIC found on some + H616 boards. config AXP717_POWER bool "axp717 pmic support" select AXP_PMIC_BUS select CMD_POWEROFF - ---help--- - Select this to enable support for the AXP717 PMIC found on some boards. + help + Select this to enable support for the AXP717 PMIC found on some boards. config AXP803_POWER bool "AXP803 PMIC support" select AXP_PMIC_BUS - ---help--- - Select this to enable support for the AXP803 PMIC found on some boards. + help + Select this to enable support for the AXP803 PMIC found on some boards. config AXP809_POWER bool "axp809 pmic support" depends on MACH_SUN9I select AXP_PMIC_BUS select CMD_POWEROFF - ---help--- - Say y here to enable support for the axp809 pmic found on A80 boards. + help + Say y here to enable support for the axp809 pmic found on A80 boards. config AXP818_POWER bool "axp818 pmic support" depends on MACH_SUN8I_A83T select AXP_PMIC_BUS select CMD_POWEROFF - ---help--- - Say y here to enable support for the axp818 pmic found on - A83T dev board. + help + Say y here to enable support for the axp818 pmic found on + A83T dev board. config AXP318W_POWER bool "axp318w pmic support" select AXP_PMIC_BUS select CMD_POWEROFF - ---help--- - Select this to enable support for the AXP318W PMIC found on some - A733 boards. + help + Select this to enable support for the AXP318W PMIC found on some + A733 boards. config SY8106A_POWER bool "SY8106A pmic support" depends on MACH_SUNXI_H3_H5 - ---help--- - Select this to enable support for the SY8106A pmic found on some - H3 boards. + help + Select this to enable support for the SY8106A pmic found on some + H3 boards. endchoice
@@ -166,22 +166,22 @@ config AXP_I2C_ADDRESS default 0x36 if AXP318W_POWER default 0x30 if AXP152_POWER default 0x34 - ---help--- - I2C address of the AXP PMIC, used for the SPL only. + help + I2C address of the AXP PMIC, used for the SPL only. config AXP_DCDC1_VOLT int "axp pmic dcdc1 voltage" depends on AXP221_POWER || AXP809_POWER || AXP818_POWER || AXP803_POWER default 3300 if AXP818_POWER || MACH_SUN8I_R40 || AXP803_POWER default 3000 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I - ---help--- - Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to - disable dcdc1. On A23 / A31 / A33 (axp221) boards dcdc1 is used for - generic 3.3V IO voltage for external devices like the lcd-panal and - sdcard interfaces, etc. On most boards dcdc1 is undervolted to 3.0V to - save battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T - dcdc1 is used for VCC-IO, nand, usb0, sd , etc. On A80 dcdc1 normally - powers some of the pingroups, NAND/eMMC, SD/MMC, and USB OTG. + help + Set the voltage (mV) to program the axp pmic dcdc1 at, set to 0 to + disable dcdc1. On A23 / A31 / A33 (axp221) boards dcdc1 is used for + generic 3.3V IO voltage for external devices like the lcd-panal and + sdcard interfaces, etc. On most boards dcdc1 is undervolted to 3.0V to + save battery. On A31 devices dcdc1 is also used for VCC-IO. On A83T + dcdc1 is used for VCC-IO, nand, usb0, sd , etc. On A80 dcdc1 normally + powers some of the pingroups, NAND/eMMC, SD/MMC, and USB OTG. config AXP_DCDC2_VOLT int "axp pmic dcdc2 voltage"
@@ -194,16 +194,16 @@ config AXP_DCDC2_VOLT default 1200 if MACH_SUN6I default 1100 if MACH_SUN8I default 0 if MACH_SUN9I - ---help--- - Set the voltage (mV) to program the axp pmic dcdc2 at, set to 0 to - disable dcdc2. - On A10(s) / A13 / A20 boards dcdc2 is VDD-CPU and should be 1.4V. - On A31 boards dcdc2 is used for VDD-GPU and should be 1.2V. - On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V. - On A80 boards dcdc2 powers the GPU and can be left off. - On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V. - On R40 boards dcdc2 is VDD-CPU and should be 1.1V - On boards using the AXP313 or AXP717 it's often VDD-CPU. + help + Set the voltage (mV) to program the axp pmic dcdc2 at, set to 0 to + disable dcdc2. + On A10(s) / A13 / A20 boards dcdc2 is VDD-CPU and should be 1.4V. + On A31 boards dcdc2 is used for VDD-GPU and should be 1.2V. + On A23/A33 boards dcdc2 is used for VDD-SYS and should be 1.1V. + On A80 boards dcdc2 powers the GPU and can be left off. + On A83T boards dcdc2 is used for VDD-CPUA(cluster 0) and should be 0.9V. + On R40 boards dcdc2 is VDD-CPU and should be 1.1V + On boards using the AXP313 or AXP717 it's often VDD-CPU. config AXP_DCDC3_VOLT int "axp pmic dcdc3 voltage"
@@ -214,18 +214,18 @@ config AXP_DCDC3_VOLT default 1100 if AXP313_POWER default 1100 if MACH_SUN8I_R40 default 1200 if MACH_SUN6I || MACH_SUN8I - ---help--- - Set the voltage (mV) to program the axp pmic dcdc3 at, set to 0 to - disable dcdc3. - On A10(s) / A13 / A20 boards with an axp209 dcdc3 is VDD-INT-DLL and - should be 1.25V. - On A10s boards with an axp152 dcdc3 is VCC-DRAM and should be 1.5V. - On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V. - On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V. - On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V. - On R40 boards dcdc3 is VDD-SYS and VDD-GPU and should be 1.1V. - On boards using the AXP313 or AXP717 it's often VDD-DRAM and should - be 1.1V for LPDDR4. + help + Set the voltage (mV) to program the axp pmic dcdc3 at, set to 0 to + disable dcdc3. + On A10(s) / A13 / A20 boards with an axp209 dcdc3 is VDD-INT-DLL and + should be 1.25V. + On A10s boards with an axp152 dcdc3 is VCC-DRAM and should be 1.5V. + On A23 / A31 / A33 boards dcdc3 is VDD-CPU and should be 1.2V. + On A80 boards dcdc3 is used for VDD-CPUA(cluster 0) and should be 0.9V. + On A83T boards dcdc3 is used for VDD-CPUB(cluster 1) and should be 0.9V. + On R40 boards dcdc3 is VDD-SYS and VDD-GPU and should be 1.1V. + On boards using the AXP313 or AXP717 it's often VDD-DRAM and should + be 1.1V for LPDDR4. config AXP_DCDC4_VOLT int "axp pmic dcdc4 voltage"
@@ -235,25 +235,25 @@ config AXP_DCDC4_VOLT default 0 if MACH_SUN8I default 900 if MACH_SUN9I default 1500 if AXP305_POWER - ---help--- - Set the voltage (mV) to program the axp pmic dcdc4 at, set to 0 to - disable dcdc4. - On A10s boards with an axp152 dcdc4 is VDD-INT-DLL and should be 1.25V. - On A31 boards dcdc4 is used for VDD-SYS and should be 1.2V. - On A23 / A33 boards dcdc4 is unused and should be disabled. - On A80 boards dcdc4 powers VDD-SYS, HDMI, USB OTG and should be 0.9V. - On A83T boards dcdc4 is used for VDD-GPU. - On H616 boards dcdcd is used for VCC-DRAM. + help + Set the voltage (mV) to program the axp pmic dcdc4 at, set to 0 to + disable dcdc4. + On A10s boards with an axp152 dcdc4 is VDD-INT-DLL and should be 1.25V. + On A31 boards dcdc4 is used for VDD-SYS and should be 1.2V. + On A23 / A33 boards dcdc4 is unused and should be disabled. + On A80 boards dcdc4 powers VDD-SYS, HDMI, USB OTG and should be 0.9V. + On A83T boards dcdc4 is used for VDD-GPU. + On H616 boards dcdcd is used for VCC-DRAM. config AXP_DCDC5_VOLT int "axp pmic dcdc5 voltage" depends on AXP221_POWER || AXP809_POWER || AXP818_POWER || AXP803_POWER default 1500 if MACH_SUN6I || MACH_SUN8I || MACH_SUN9I - ---help--- - Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to - disable dcdc5. - On A23 / A31 / A33 / A80 / A83T / R40 boards dcdc5 is VCC-DRAM and - should be 1.5V, 1.35V if DDR3L is used. + help + Set the voltage (mV) to program the axp pmic dcdc5 at, set to 0 to + disable dcdc5. + On A23 / A31 / A33 / A80 / A83T / R40 boards dcdc5 is VCC-DRAM and + should be 1.5V, 1.35V if DDR3L is used. config AXP_ALDO1_VOLT int "axp pmic (a)ldo1 voltage"
@@ -261,14 +261,14 @@ config AXP_ALDO1_VOLT default 0 if MACH_SUN6I || MACH_SUN8I_R40 default 1800 if MACH_SUN8I_A83T default 3000 if MACH_SUN8I || MACH_SUN9I - ---help--- - Set the voltage (mV) to program the axp pmic aldo1 at, set to 0 to - disable aldo1. - On A31 boards aldo1 is often used to power the wifi module. - On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V. - On A80 boards aldo1 powers the USB hosts and should be 3.0V. - On A83T / H8 boards aldo1 is used for MIPI CSI, DSI, HDMI, EFUSE, and - should be 1.8V. + help + Set the voltage (mV) to program the axp pmic aldo1 at, set to 0 to + disable aldo1. + On A31 boards aldo1 is often used to power the wifi module. + On A23 / A33 boards aldo1 is used for VCC-IO and should be 3.0V. + On A80 boards aldo1 powers the USB hosts and should be 3.0V. + On A83T / H8 boards aldo1 is used for MIPI CSI, DSI, HDMI, EFUSE, and + should be 1.8V. config AXP_ALDO2_VOLT int "axp pmic (a)ldo2 voltage"
@@ -277,188 +277,188 @@ config AXP_ALDO2_VOLT default 0 if MACH_SUN6I || MACH_SUN9I default 1800 if MACH_SUN8I_A83T default 2500 if MACH_SUN8I - ---help--- - Set the voltage (mV) to program the axp pmic aldo2 at, set to 0 to - disable aldo2. - On A10(s) / A13 / A20 boards aldo2 is AVCC and should be 3.0V. - On A31 boards aldo2 is typically unused and should be disabled. - On A31 boards aldo2 may be used for LPDDR2 then it should be 1.8V. - On A23 / A33 boards aldo2 is used for VDD-DLL and should be 2.5V. - On A80 boards aldo2 powers PB pingroup and camera IO and can be left off. - On A83T / H8 boards aldo2 powers VDD-DLL, VCC18-PLL, CPVDD, VDD18-ADC, - LPDDR2, and the codec. It should be 1.8V. + help + Set the voltage (mV) to program the axp pmic aldo2 at, set to 0 to + disable aldo2. + On A10(s) / A13 / A20 boards aldo2 is AVCC and should be 3.0V. + On A31 boards aldo2 is typically unused and should be disabled. + On A31 boards aldo2 may be used for LPDDR2 then it should be 1.8V. + On A23 / A33 boards aldo2 is used for VDD-DLL and should be 2.5V. + On A80 boards aldo2 powers PB pingroup and camera IO and can be left off. + On A83T / H8 boards aldo2 powers VDD-DLL, VCC18-PLL, CPVDD, VDD18-ADC, + LPDDR2, and the codec. It should be 1.8V. config AXP_ALDO3_VOLT int "axp pmic (a)ldo3 voltage" depends on AXP209_POWER || AXP221_POWER || AXP809_POWER || AXP818_POWER default 0 if AXP209_POWER || MACH_SUN9I default 3000 if MACH_SUN6I || MACH_SUN8I - ---help--- - Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to - disable aldo3. - On A10(s) / A13 / A20 boards aldo3 should be 2.8V. - On A23 / A31 / A33 / R40 boards aldo3 is VCC-PLL and AVCC and should - be 3.0V. - On A80 boards aldo3 is normally not used. - On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be - 3.0V. + help + Set the voltage (mV) to program the axp pmic aldo3 at, set to 0 to + disable aldo3. + On A10(s) / A13 / A20 boards aldo3 should be 2.8V. + On A23 / A31 / A33 / R40 boards aldo3 is VCC-PLL and AVCC and should + be 3.0V. + On A80 boards aldo3 is normally not used. + On A83T / H8 boards aldo3 is AVCC, VCC-PL, and VCC-LED, and should be + 3.0V. choice prompt "axp pmic (a)ldo3 voltage rate control" depends on AXP209_POWER default AXP_ALDO3_VOLT_SLOPE_NONE - ---help--- - The AXP can slowly ramp up voltage to reduce the inrush current when - changing voltages. - Note, this does not apply when enabling/disabling LDO3. See - "axp pmic (a)ldo3 inrush quirk" below to enable a slew rate to limit - inrush current on broken board designs. + help + The AXP can slowly ramp up voltage to reduce the inrush current when + changing voltages. + Note, this does not apply when enabling/disabling LDO3. See + "axp pmic (a)ldo3 inrush quirk" below to enable a slew rate to limit + inrush current on broken board designs. config AXP_ALDO3_VOLT_SLOPE_NONE bool "No voltage slope" - ---help--- - Tries to reach the next voltage setting near instantaneously. Measurements - indicate that this is about 0.0167 V/uS. + help + Tries to reach the next voltage setting near instantaneously. Measurements + indicate that this is about 0.0167 V/uS. config AXP_ALDO3_VOLT_SLOPE_16 bool "1.6 mV per uS" - ---help--- - Increases the voltage by 1.6 mV per uS until the final voltage has - been reached. Note that the scaling is in 25 mV steps and thus - the slew rate in reality is about 25 mV/31.250 uS. + help + Increases the voltage by 1.6 mV per uS until the final voltage has + been reached. Note that the scaling is in 25 mV steps and thus + the slew rate in reality is about 25 mV/31.250 uS. config AXP_ALDO3_VOLT_SLOPE_08 bool "0.8 mV per uS" - ---help--- - Increases the voltage by 0.8 mV per uS until the final voltage has - been reached. Note that the scaling is in 25 mV steps however and thus - the slew rate in reality is about 25 mV/15.625 uS. - This is the slowest supported rate. + help + Increases the voltage by 0.8 mV per uS until the final voltage has + been reached. Note that the scaling is in 25 mV steps however and thus + the slew rate in reality is about 25 mV/15.625 uS. + This is the slowest supported rate. endchoice config AXP_ALDO3_INRUSH_QUIRK bool "axp pmic (a)ldo3 inrush quirk" depends on AXP209_POWER - ---help--- - The reference design denotes a value of 4.7 uF for the output capacitor - of LDO3. Some boards have too high capacitance causing an inrush current - and resulting an AXP209 shutdown. + help + The reference design denotes a value of 4.7 uF for the output capacitor + of LDO3. Some boards have too high capacitance causing an inrush current + and resulting an AXP209 shutdown. config AXP_ALDO4_VOLT int "axp pmic (a)ldo4 voltage" depends on AXP209_POWER default 0 if AXP209_POWER - ---help--- - Set the voltage (mV) to program the axp pmic aldo4 at, set to 0 to - disable aldo4. - On A10(s) / A13 / A20 boards aldo4 should be 2.8V. + help + Set the voltage (mV) to program the axp pmic aldo4 at, set to 0 to + disable aldo4. + On A10(s) / A13 / A20 boards aldo4 should be 2.8V. config AXP_DLDO1_VOLT int "axp pmic dldo1 voltage" depends on AXP221_POWER || AXP809_POWER || AXP818_POWER default 0 - ---help--- - Set the voltage (mV) to program the axp pmic dldo1 at, set to 0 to - disable dldo1. On sun6i (A31) boards with ethernet dldo1 is often used - to power the ethernet phy. On A23, A33 and A80 boards this is often - used to power the wifi. + help + Set the voltage (mV) to program the axp pmic dldo1 at, set to 0 to + disable dldo1. On sun6i (A31) boards with ethernet dldo1 is often used + to power the ethernet phy. On A23, A33 and A80 boards this is often + used to power the wifi. config AXP_DLDO2_VOLT int "axp pmic dldo2 voltage" depends on AXP221_POWER || AXP809_POWER || AXP818_POWER default 3000 if MACH_SUN9I default 0 - ---help--- - Set the voltage (mV) to program the axp pmic dldo2 at, set to 0 to - disable dldo2. - On A80 boards dldo2 normally powers the PL pins and should be 3.0V. + help + Set the voltage (mV) to program the axp pmic dldo2 at, set to 0 to + disable dldo2. + On A80 boards dldo2 normally powers the PL pins and should be 3.0V. config AXP_DLDO3_VOLT int "axp pmic dldo3 voltage" depends on AXP221_POWER || AXP818_POWER default 0 - ---help--- - Set the voltage (mV) to program the axp pmic dldo3 at, set to 0 to - disable dldo3. + help + Set the voltage (mV) to program the axp pmic dldo3 at, set to 0 to + disable dldo3. config AXP_DLDO4_VOLT int "axp pmic dldo4 voltage" depends on AXP221_POWER || AXP818_POWER default 0 - ---help--- - Set the voltage (mV) to program the axp pmic dldo4 at, set to 0 to - disable dldo4. + help + Set the voltage (mV) to program the axp pmic dldo4 at, set to 0 to + disable dldo4. config AXP_ELDO1_VOLT int "axp pmic eldo1 voltage" depends on AXP221_POWER || AXP809_POWER || AXP818_POWER default 0 - ---help--- - Set the voltage (mV) to program the axp pmic eldo1 at, set to 0 to - disable eldo1. + help + Set the voltage (mV) to program the axp pmic eldo1 at, set to 0 to + disable eldo1. config AXP_ELDO2_VOLT int "axp pmic eldo2 voltage" depends on AXP221_POWER || AXP809_POWER || AXP818_POWER default 0 - ---help--- - Set the voltage (mV) to program the axp pmic eldo2 at, set to 0 to - disable eldo2. + help + Set the voltage (mV) to program the axp pmic eldo2 at, set to 0 to + disable eldo2. config AXP_ELDO3_VOLT int "axp pmic eldo3 voltage" depends on AXP221_POWER || AXP809_POWER || AXP818_POWER default 3000 if MACH_SUN9I default 0 - ---help--- - Set the voltage (mV) to program the axp pmic eldo3 at, set to 0 to - disable eldo3. On some A31(s) tablets it might be used to supply - 1.2V for the SSD2828 chip (converter of parallel LCD interface - into MIPI DSI). - On A80 boards it powers the PM pingroup and should be 3.0V. + help + Set the voltage (mV) to program the axp pmic eldo3 at, set to 0 to + disable eldo3. On some A31(s) tablets it might be used to supply + 1.2V for the SSD2828 chip (converter of parallel LCD interface + into MIPI DSI). + On A80 boards it powers the PM pingroup and should be 3.0V. config AXP_FLDO1_VOLT int "axp pmic fldo1 voltage" depends on AXP818_POWER default 0 if MACH_SUN8I_A83T - ---help--- - Set the voltage (mV) to program the axp pmic fldo1 at, set to 0 to - disable fldo1. - On A83T / H8 boards fldo1 is VCC-HSIC and should be 1.2V if HSIC is - used. + help + Set the voltage (mV) to program the axp pmic fldo1 at, set to 0 to + disable fldo1. + On A83T / H8 boards fldo1 is VCC-HSIC and should be 1.2V if HSIC is + used. config AXP_FLDO2_VOLT int "axp pmic fldo2 voltage" depends on AXP818_POWER default 900 if MACH_SUN8I_A83T - ---help--- - Set the voltage (mV) to program the axp pmic fldo2 at, set to 0 to - disable fldo2. - On A83T / H8 boards fldo2 is VCC-CPUS and should be 0.9V. + help + Set the voltage (mV) to program the axp pmic fldo2 at, set to 0 to + disable fldo2. + On A83T / H8 boards fldo2 is VCC-CPUS and should be 0.9V. config AXP_FLDO3_VOLT int "axp pmic fldo3 voltage" depends on AXP818_POWER default 0 - ---help--- - Set the voltage (mV) to program the axp pmic fldo3 at, set to 0 to - disable fldo3. + help + Set the voltage (mV) to program the axp pmic fldo3 at, set to 0 to + disable fldo3. config AXP_SW_ON bool "axp pmic sw on" depends on AXP809_POWER || AXP818_POWER - ---help--- - Enable to turn on axp pmic sw. + help + Enable to turn on axp pmic sw. config SY8106A_VOUT1_VOLT int "SY8106A pmic VOUT1 voltage" depends on SY8106A_POWER default 1200 - ---help--- - Set the voltage (mV) to program the SY8106A pmic VOUT1. This - is typically used to power the VDD-CPU and should be 1200mV. - Values can range from 680mV till 1950mV. + help + Set the voltage (mV) to program the SY8106A pmic VOUT1. This + is typically used to power the VDD-CPU and should be 1200mV. + Values can range from 680mV till 1950mV. config TPS6586X_POWER bool "Enable legacy driver for TI TPS6586x power management chip"
@@ -467,9 +467,9 @@ config TWL4030_POWER depends on OMAP34XX bool "Enable driver for TI TWL4030 power management chip" imply CMD_POWEROFF - ---help--- - The TWL4030 in a combination audio CODEC/power management with - GPIO and it is commonly used with the OMAP3 family of processors + help + The TWL4030 in a combination audio CODEC/power management with + GPIO and it is commonly used with the OMAP3 family of processors config POWER_MT6323 bool "Poweroff driver for mediatek mt6323"
drivers/power/domain/Kconfig +4 -4
@@ -35,10 +35,10 @@ config BCM6328_POWER_DOMAIN config IMX8_POWER_DOMAIN bool "Enable i.MX8 power domain driver" - depends on ARCH_IMX8 - help - Enable support for manipulating NXP i.MX8 on-SoC power domains via IPC - requests to the SCU. + depends on ARCH_IMX8 + help + Enable support for manipulating NXP i.MX8 on-SoC power domains via IPC + requests to the SCU. config IMX8M_POWER_DOMAIN bool "Enable i.MX8M power domain driver"
drivers/power/pmic/Kconfig +174 -174
504 lines not on this page · raw message
drivers/power/regulator/Kconfig +199 -199
610 lines not on this page · raw message
--
2.39.5
PATCH 14/18 Kconfig: usb: restyle
In reply to Johan JonkerRestyle all Kconfigs for "usb":
Menu entries : no space left
Menu attributes: 1 TAB
Help text : 1 TAB + 2 spaces
Replace '---help---' by 'help'
--- drivers/usb/Kconfig | 16 ++++++------- drivers/usb/eth/Kconfig | 16 ++++++------- drivers/usb/gadget/Kconfig | 22 +++++++++--------- drivers/usb/host/Kconfig | 44 ++++++++++++++++++------------------ drivers/usb/musb-new/Kconfig | 14 ++++++------ 5 files changed, 56 insertions(+), 56 deletions(-)
drivers/usb/Kconfig +8 -8
@@ -1,7 +1,7 @@ menuconfig USB bool "USB support" select BLK - ---help--- + help Universal Serial Bus (USB) is a specification for a serial bus subsystem which offers higher speeds and more features than the traditional PC serial port. The bus supplies power to peripherals
@@ -94,7 +94,7 @@ comment "USB peripherals" config USB_STORAGE bool "USB Mass Storage support" - ---help--- + help Say Y here if you want to connect USB mass storage devices to your board's USB port.
@@ -103,7 +103,7 @@ config USB_KEYBOARD depends on DM_USB select DM_KEYBOARD select SYS_STDIO_DEREGISTER - ---help--- + help Say Y here if you want to use a USB keyboard for U-Boot command line input.
@@ -111,7 +111,7 @@ config USB_ONBOARD_HUB bool "Onboard USB hub support" depends on DM_USB select DEVRES - ---help--- + help Say Y here if you want to support discrete onboard USB hubs that don't require an additional control bus for initialization, but need some non-trivial form of initialization, such as enabling a
@@ -163,17 +163,17 @@ choice prompt "USB keyboard polling" default SYS_USB_EVENT_POLL_VIA_INT_QUEUE if ARCH_SUNXI default SYS_USB_EVENT_POLL - ---help--- + help Enable a polling mechanism for USB keyboard. config SYS_USB_EVENT_POLL - bool "Interrupt polling" + bool "Interrupt polling" config SYS_USB_EVENT_POLL_VIA_INT_QUEUE - bool "Poll via interrupt queue" + bool "Poll via interrupt queue" config SYS_USB_EVENT_POLL_VIA_CONTROL_EP - bool "Poll via control EP" + bool "Poll via control EP" endchoice
drivers/usb/eth/Kconfig +8 -8
@@ -1,6 +1,6 @@ menuconfig USB_HOST_ETHER bool "USB to Ethernet Controller Drivers" - ---help--- + help Say Y here if you would like to enable support for USB Ethernet adapters.
@@ -9,14 +9,14 @@ if USB_HOST_ETHER config USB_ETHER_ASIX bool "ASIX AX8817X (USB 2.0) support" depends on USB_HOST_ETHER - ---help--- + help Say Y here if you would like to support ASIX AX8817X based USB 2.0 Ethernet Devices. config USB_ETHER_ASIX88179 bool "ASIX AX88179 (USB 3.0) support" depends on USB_HOST_ETHER - ---help--- + help Say Y here if you would like to support ASIX AX88179 based USB 3.0 Ethernet Devices.
@@ -24,7 +24,7 @@ config USB_ETHER_LAN75XX bool "Microchip LAN75XX support" depends on USB_HOST_ETHER depends on PHYLIB - ---help--- + help Say Y here if you would like to support Microchip LAN75XX Hi-Speed USB 2.0 to 10/100/1000 Gigabit Ethernet controller. Supports 10Base-T/ 100Base-TX/1000Base-T.
@@ -34,7 +34,7 @@ config USB_ETHER_LAN78XX bool "Microchip LAN78XX support" depends on USB_HOST_ETHER depends on PHYLIB - ---help--- + help Say Y here if you would like to support Microchip LAN78XX USB 3.1 Gen 1 to 10/100/1000 Gigabit Ethernet controller. Supports 10Base-T/ 100Base-TX/1000Base-T.
@@ -43,14 +43,14 @@ config USB_ETHER_LAN78XX config USB_ETHER_MCS7830 bool "MOSCHIP MCS7830 (7730/7830/7832) suppport" depends on USB_HOST_ETHER - ---help--- + help Say Y here if you would like to support MOSCHIP MCS7830 based (7730/7830/7832) USB 2.0 Ethernet Devices. config USB_ETHER_RTL8152 bool "Realtek RTL8152B/RTL8153 support" depends on USB_HOST_ETHER - ---help--- + help Say Y here if you would like to support Realtek RTL8152B/RTL8153 base USB Ethernet Devices. This driver also supports compatible devices from Samsung, Lenovo, TP-LINK and Nvidia.
@@ -58,7 +58,7 @@ config USB_ETHER_RTL8152 config USB_ETHER_SMSC95XX bool "SMSC LAN95x support" depends on USB_HOST_ETHER - ---help--- + help Say Y here if you would like to support SMSC LAN95xx based USB 2.0 Ethernet Devices.
drivers/usb/gadget/Kconfig +11 -11
@@ -19,10 +19,10 @@ menuconfig USB_GADGET select DM_USB imply CMD_BIND help - USB is a master/slave protocol, organized with one master - host (such as a PC) controlling up to 127 peripheral devices. - The USB hardware is asymmetric, which makes it easier to set up: - you can't connect a "to-the-host" connector to a peripheral. + USB is a master/slave protocol, organized with one master + host (such as a PC) controlling up to 127 peripheral devices. + The USB hardware is asymmetric, which makes it easier to set up: + you can't connect a "to-the-host" connector to a peripheral. U-Boot can run in the host, or in the peripheral. In both cases you need a low level bus controller driver, and some software
@@ -164,10 +164,10 @@ config USB_GADGET_VBUS_DRAW range 2 500 default 2 help - Some devices need to draw power from USB when they are - configured, perhaps to operate circuitry or to recharge - batteries. This is in addition to any local power supply, - such as an AC adapter or batteries. + Some devices need to draw power from USB when they are + configured, perhaps to operate circuitry or to recharge + batteries. This is in addition to any local power supply, + such as an AC adapter or batteries. Enter the maximum power your device draws through USB, in milliAmperes. The permitted range of values is 2 - 500 mA;
@@ -350,9 +350,9 @@ config SPL_DFU_RAM bool "RAM device" depends on SPL_DFU && SPL_RAM_SUPPORT help - select RAM/DDR memory device for loading binary images - (u-boot/kernel) to the selected device partition using - DFU and execute the u-boot/kernel from RAM. + select RAM/DDR memory device for loading binary images + (u-boot/kernel) to the selected device partition using + DFU and execute the u-boot/kernel from RAM. endchoice
drivers/usb/host/Kconfig +22 -22
176 lines not on this page · raw message
drivers/usb/musb-new/Kconfig +7 -7
@@ -23,11 +23,11 @@ config USB_MUSB_GADGET if USB_MUSB_HOST || USB_MUSB_GADGET config USB_MUSB_SC5XX - bool "Analog Devices MUSB support" - depends on (SC57X || SC58X) + bool "Analog Devices MUSB support" + depends on (SC57X || SC58X) help - Say y here to enable support for the USB controller on - ADI SC57X/SC58X processors. + Say y here to enable support for the USB controller on + ADI SC57X/SC58X processors. config USB_MUSB_DA8XX bool "Enable DA8xx MUSB Controller"
@@ -81,9 +81,9 @@ config USB_MUSB_SUNXI depends on PHY_SUN4I_USB select USB_MUSB_PIO_ONLY default y - ---help--- - Say y here to enable support for the sunxi OTG / DRC USB controller - used on almost all sunxi boards. + help + Say y here to enable support for the sunxi OTG / DRC USB controller + used on almost all sunxi boards. config USB_MUSB_UX500 bool "Enable ST-Ericsson Ux500 USB controller"
--
2.39.5
PATCH 15/18 Kconfig: video: restyle
In reply to Johan JonkerRestyle all Kconfigs for "video":
Menu entries : no space left
Menu attributes: 1 TAB
Help text : 1 TAB + 2 spaces
Replace '---help---' by 'help'
--- drivers/video/Kconfig | 178 ++++++++++++++++----------------- drivers/video/bridge/Kconfig | 4 +- drivers/video/imx/Kconfig | 2 +- drivers/video/rockchip/Kconfig | 4 +- drivers/video/tegra/Kconfig | 42 ++++---- drivers/video/ti/Kconfig | 2 +- drivers/video/zynqmp/Kconfig | 6 +- 7 files changed, 119 insertions(+), 119 deletions(-)
drivers/video/Kconfig +89 -89
@@ -247,10 +247,10 @@ config SYS_WHITE_ON_BLACK bool "Display console as white on a black background" default y if ARCH_AT91 || ARCH_EXYNOS || ARCH_ROCKCHIP || ARCH_TEGRA || X86 || ARCH_SUNXI help - Normally the display is black on a white background, Enable this - option to invert this, i.e. white on a black background. This can be - better in low-light situations or to reduce eye strain in some - cases. + Normally the display is black on a white background, Enable this + option to invert this, i.e. white on a black background. This can be + better in low-light situations or to reduce eye strain in some + cases. config NO_FB_CLEAR bool "Skip framebuffer clear"
@@ -508,10 +508,10 @@ config FRAMEBUFFER_VESA_MODE config VIDEO_LCD_ANX9804 bool "ANX9804 bridge chip" - ---help--- - Support for the ANX9804 bridge chip, which can take pixel data coming - from a parallel LCD interface and translate it on the fy into a DP - interface for driving eDP TFT displays. It uses I2C for configuration. + help + Support for the ANX9804 bridge chip, which can take pixel data coming + from a parallel LCD interface and translate it on the fy into a DP + interface for driving eDP TFT displays. It uses I2C for configuration. config ATMEL_LCD bool "Atmel LCD panel support"
@@ -549,8 +549,8 @@ config VIDEO_LCD_HIMAX_HX8394 depends on PANEL && BACKLIGHT select VIDEO_MIPI_DSI help - Say Y here if you want to enable support for Himax HX8394 - dsi 4dl panel. + Say Y here if you want to enable support for Himax HX8394 + dsi 4dl panel. config VIDEO_LCD_ILITEK_ILI9806E bool "Ilitek ILI9806E-based panels"
@@ -574,15 +574,15 @@ config VIDEO_LCD_NOVATEK_NT35510 bool "Novatek NT35510 DSI LCD panel support" select VIDEO_MIPI_DSI help - Say Y here if you want to enable support for Novatek nt35510 - dsi panel. + Say Y here if you want to enable support for Novatek nt35510 + dsi panel. config VIDEO_LCD_ORISETECH_OTM8009A bool "OTM8009A DSI LCD panel support" select VIDEO_MIPI_DSI help - Say Y here if you want to enable support for Orise Technology - otm8009a 480x800 dsi 2dl panel. + Say Y here if you want to enable support for Orise Technology + otm8009a 480x800 dsi 2dl panel. config VIDEO_LCD_LG_LD070WX3 bool "LD070WX3 DSI LCD panel support"
@@ -604,8 +604,8 @@ config VIDEO_LCD_RAYDIUM_RM68200 bool "RM68200 DSI LCD panel support" select VIDEO_MIPI_DSI help - Say Y here if you want to enable support for Raydium RM68200 - 720x1280 DSI video mode panel. + Say Y here if you want to enable support for Raydium RM68200 + 720x1280 DSI video mode panel. config VIDEO_LCD_RENESAS_R61307 tristate "Renesas R61307 DSI video mode panel"
@@ -654,38 +654,38 @@ config VIDEO_LCD_SHARP_LQ101R1SX01 config VIDEO_LCD_SSD2828 bool "SSD2828 bridge chip" - ---help--- - Support for the SSD2828 bridge chip, which can take pixel data coming - from a parallel LCD interface and translate it on the fly into MIPI DSI - interface for driving a MIPI compatible LCD panel. It uses SPI for - configuration. + help + Support for the SSD2828 bridge chip, which can take pixel data coming + from a parallel LCD interface and translate it on the fly into MIPI DSI + interface for driving a MIPI compatible LCD panel. It uses SPI for + configuration. config VIDEO_LCD_SSD2828_TX_CLK int "SSD2828 TX_CLK frequency (in MHz)" depends on VIDEO_LCD_SSD2828 default 0 - ---help--- - The frequency of the crystal, which is clocking SSD2828. It may be - anything in the 8MHz-30MHz range and the exact value should be - retrieved from the board schematics. Or in the case of Allwinner - hardware, it can be usually found as 'lcd_xtal_freq' variable in - FEX files. It can be also set to 0 for selecting PCLK from the - parallel LCD interface instead of TX_CLK as the PLL clock source. + help + The frequency of the crystal, which is clocking SSD2828. It may be + anything in the 8MHz-30MHz range and the exact value should be + retrieved from the board schematics. Or in the case of Allwinner + hardware, it can be usually found as 'lcd_xtal_freq' variable in + FEX files. It can be also set to 0 for selecting PCLK from the + parallel LCD interface instead of TX_CLK as the PLL clock source. config VIDEO_LCD_SSD2828_RESET string "RESET pin of SSD2828" depends on VIDEO_LCD_SSD2828 default "" - ---help--- - The reset pin of SSD2828 chip. This takes a string in the format - understood by 'sunxi_name_to_gpio' function, e.g. PH1 for pin 1 of port H. + help + The reset pin of SSD2828 chip. This takes a string in the format + understood by 'sunxi_name_to_gpio' function, e.g. PH1 for pin 1 of port H. config VIDEO_LCD_TDO_TL070WSH30 bool "TDO TL070WSH30 DSI LCD panel support" select VIDEO_MIPI_DSI help - Say Y here if you want to enable support for TDO TL070WSH30 - 1024x600 DSI video mode panel. + Say Y here if you want to enable support for TDO TL070WSH30 + 1024x600 DSI video mode panel. config VIDEO_LCD_HITACHI_TX10D07VM0BAA tristate "Hitachi TX10D07VM0BAA 480x800 MIPI DSI video mode panel"
@@ -697,10 +697,10 @@ config VIDEO_LCD_HITACHI_TX10D07VM0BAA config VIDEO_LCD_HITACHI_TX18D42VM bool "Hitachi tx18d42vm LVDS LCD panel support" - ---help--- - Support for Hitachi tx18d42vm LVDS LCD panels, these panels have a - lcd controller which needs to be initialized over SPI, once that is - done they work like a regular LVDS panel. + help + Support for Hitachi tx18d42vm LVDS LCD panels, these panels have a + lcd controller which needs to be initialized over SPI, once that is + done they work like a regular LVDS panel. config VIDEO_LCD_SONY_L4F00430T01 tristate "Sony L4F00430T01 480x800 LCD panel support"
@@ -723,44 +723,44 @@ config VIDEO_LCD_SPI_CS string "SPI CS pin for LCD related config job" depends on VIDEO_LCD_SSD2828 || VIDEO_LCD_HITACHI_TX18D42VM default "" - ---help--- - This is one of the SPI communication pins, involved in setting up a - working LCD configuration. The exact role of SPI may differ for - different hardware setups. The option takes a string in the format - understood by 'sunxi_name_to_gpio' function, e.g. PH1 for pin 1 of port H. + help + This is one of the SPI communication pins, involved in setting up a + working LCD configuration. The exact role of SPI may differ for + different hardware setups. The option takes a string in the format + understood by 'sunxi_name_to_gpio' function, e.g. PH1 for pin 1 of port H. config VIDEO_LCD_SPI_SCLK string "SPI SCLK pin for LCD related config job" depends on VIDEO_LCD_SSD2828 || VIDEO_LCD_HITACHI_TX18D42VM default "" - ---help--- - This is one of the SPI communication pins, involved in setting up a - working LCD configuration. The exact role of SPI may differ for - different hardware setups. The option takes a string in the format - understood by 'sunxi_name_to_gpio' function, e.g. PH1 for pin 1 of port H. + help + This is one of the SPI communication pins, involved in setting up a + working LCD configuration. The exact role of SPI may differ for + different hardware setups. The option takes a string in the format + understood by 'sunxi_name_to_gpio' function, e.g. PH1 for pin 1 of port H. config VIDEO_LCD_SPI_MOSI string "SPI MOSI pin for LCD related config job" depends on VIDEO_LCD_SSD2828 || VIDEO_LCD_HITACHI_TX18D42VM default "" - ---help--- - This is one of the SPI communication pins, involved in setting up a - working LCD configuration. The exact role of SPI may differ for - different hardware setups. The option takes a string in the format - understood by 'sunxi_name_to_gpio' function, e.g. PH1 for pin 1 of port H. + help + This is one of the SPI communication pins, involved in setting up a + working LCD configuration. The exact role of SPI may differ for + different hardware setups. The option takes a string in the format + understood by 'sunxi_name_to_gpio' function, e.g. PH1 for pin 1 of port H. config VIDEO_LCD_SPI_MISO string "SPI MISO pin for LCD related config job (optional)" depends on VIDEO_LCD_SSD2828 default "" - ---help--- - This is one of the SPI communication pins, involved in setting up a - working LCD configuration. The exact role of SPI may differ for - different hardware setups. If wired up, this pin may provide additional - useful functionality. Such as bi-directional communication with the - hardware and LCD panel id retrieval (if the panel can report it). The - option takes a string in the format understood by 'sunxi_name_to_gpio' - function, e.g. PH1 for pin 1 of port H. + help + This is one of the SPI communication pins, involved in setting up a + working LCD configuration. The exact role of SPI may differ for + different hardware setups. If wired up, this pin may provide additional + useful functionality. Such as bi-directional communication with the + hardware and LCD panel id retrieval (if the panel can report it). The + option takes a string in the format understood by 'sunxi_name_to_gpio' + function, e.g. PH1 for pin 1 of port H. source "drivers/video/meson/Kconfig"
@@ -768,9 +768,9 @@ config VIDEO_MVEBU bool "Armada XP LCD controller" depends on ARCH_MVEBU imply VIDEO_DAMAGE - ---help--- - Support for the LCD controller integrated in the Marvell - Armada XP SoC. + help + Support for the LCD controller integrated in the Marvell + Armada XP SoC. config VIDEO_OMAP3 bool "Enable OMAP3+ DSS Support"
@@ -781,23 +781,23 @@ config VIDEO_OMAP3 config I2C_EDID bool "Enable EDID library" help - This enables library for accessing EDID data from an LCD panel. + This enables library for accessing EDID data from an LCD panel. config I2C_EDID_STANDARD bool "Enable standard timings EDID library expansion" depends on I2C_EDID help - This enables standard timings expansion for EDID data from an LCD panel. + This enables standard timings expansion for EDID data from an LCD panel. config DISPLAY bool "Enable Display support" depends on DM select I2C_EDID help - This supports drivers that provide a display, such as eDP (Embedded - DisplayPort) and HDMI (High Definition Multimedia Interface). - The devices provide a simple interface to start up the display, - read display information and enable it. + This supports drivers that provide a display, such as eDP (Embedded + DisplayPort) and HDMI (High Definition Multimedia Interface). + The devices provide a simple interface to start up the display, + read display information and enable it. config NXP_TDA19988 bool "Enable NXP TDA19988 support"
@@ -811,7 +811,7 @@ config ATMEL_HLCD depends on ARCH_AT91 imply VIDEO_DAMAGE help - HLCDC supports video output to an attached LCD panel. + HLCDC supports video output to an attached LCD panel. config BACKLIGHT_AAT2870 bool "Backlight Driver for AAT2870"
@@ -930,9 +930,9 @@ config VIDEO_NX bool "Enable video support on Nexell SoC" depends on ARCH_S5P6818 || ARCH_S5P4418 help - Nexell SoC supports many video output options including eDP and - HDMI. This option enables this support which can be used on devices - which have an eDP display connected. + Nexell SoC supports many video output options including eDP and + HDMI. This option enables this support which can be used on devices + which have an eDP display connected. config VIDEO_SEPS525 bool "Enable video support for Seps525"
@@ -1018,9 +1018,9 @@ config OSD bool "Enable OSD support" depends on DM help - This supports drivers that provide a OSD (on-screen display), which - is a (usually text-oriented) graphics buffer to show information on - a display. + This supports drivers that provide a OSD (on-screen display), which + is a (usually text-oriented) graphics buffer to show information on + a display. config SANDBOX_OSD bool "Enable sandbox OSD"
@@ -1213,10 +1213,10 @@ config SPL_SPLASH_SCREEN config SPL_SYS_WHITE_ON_BLACK bool "Display console as white on a black background at SPL" help - Normally the display is black on a white background, Enable this - option to invert this, i.e. white on a black background at spl stage. - This can be better in low-light situations or to reduce eye strain in - some cases. + Normally the display is black on a white background, Enable this + option to invert this, i.e. white on a black background at spl stage. + This can be better in low-light situations or to reduce eye strain in + some cases. config SPL_VIDEO_PCI_DEFAULT_FB_SIZE hex "Default framebuffer size to use if no drivers request it at SPL"
@@ -1279,10 +1279,10 @@ config SPL_SIMPLE_PANEL config SPL_SYS_WHITE_ON_BLACK bool "Display console as white on a black background at SPL" help - Normally the display is black on a white background, Enable this - option to invert this, i.e. white on a black background at spl stage. - This can be better in low-light situations or to reduce eye strain in - some cases. + Normally the display is black on a white background, Enable this + option to invert this, i.e. white on a black background at spl stage. + This can be better in low-light situations or to reduce eye strain in + some cases. config SPL_VIDEO_REMOVE bool "Remove video driver after SPL stage"
@@ -1408,11 +1408,11 @@ config SPL_VIDEO_BPP32 will be empty. config SPL_HIDE_LOGO_VERSION - bool "Hide the version information on the splash screen at SPL" - help - Normally the U-Boot version string is shown on the display when the - splash screen is enabled. This information is not otherwise visible - since video starts up after U-Boot has displayed the initial banner. + bool "Hide the version information on the splash screen at SPL" + help + Normally the U-Boot version string is shown on the display when the + splash screen is enabled. This information is not otherwise visible + since video starts up after U-Boot has displayed the initial banner. Enable this option to hide this information. endif
drivers/video/bridge/Kconfig +2 -2
@@ -41,8 +41,8 @@ config VIDEO_BRIDGE_ANALOGIX_ANX6345 depends on VIDEO_BRIDGE select DM_I2C help - The Analogix ANX6345 is RGB-to-DP converter. It enables an eDP LCD - panel to be connected to an parallel LCD interface. + The Analogix ANX6345 is RGB-to-DP converter. It enables an eDP LCD + panel to be connected to an parallel LCD interface. config VIDEO_BRIDGE_SOLOMON_SSD2825 bool "Solomon SSD2825 bridge driver"
drivers/video/imx/Kconfig +1 -1
@@ -20,7 +20,7 @@ config IPU_CLK_LEGACY depends on VIDEO_IPUV3 && !CLK default y help - Use legacy clock management instead of Common Clock Framework. + Use legacy clock management instead of Common Clock Framework. config IMX_LDB bool "Freescale i.MX8MP LDB bridge"
drivers/video/rockchip/Kconfig +2 -2
@@ -21,7 +21,7 @@ menuconfig VIDEO_ROCKCHIP Rockchip RK3288 and RK3399. config VIDEO_ROCKCHIP_MAX_XRES - int "Maximum horizontal resolution (for memory allocation purposes)" + int "Maximum horizontal resolution (for memory allocation purposes)" depends on VIDEO_ROCKCHIP default 3840 if DISPLAY_ROCKCHIP_HDMI default 1920
@@ -31,7 +31,7 @@ config VIDEO_ROCKCHIP_MAX_XRES framebuffer during device-model binding/probing. config VIDEO_ROCKCHIP_MAX_YRES - int "Maximum vertical resolution (for memory allocation purposes)" + int "Maximum vertical resolution (for memory allocation purposes)" depends on VIDEO_ROCKCHIP default 2160 if DISPLAY_ROCKCHIP_HDMI default 1080
drivers/video/tegra/Kconfig +21 -21
74 lines not on this page · raw message
drivers/video/ti/Kconfig +1 -1
@@ -6,4 +6,4 @@ config AM335X_LCD bool "Enable AM335x video support" depends on ARCH_OMAP2PLUS help - Supports video output to an attached LCD panel. + Supports video output to an attached LCD panel.
drivers/video/zynqmp/Kconfig +3 -3
@@ -3,6 +3,6 @@ config VIDEO_ZYNQMP_DPSUB bool "Enable video support for ZynqMP Display Port" depends on ZYNQMP_POWER_DOMAIN help - Enable support for Xilinx ZynqMP Display Port. Currently this file - is used as placeholder for driver. The main reason is to record - compatible string and calling power domain driver. + Enable support for Xilinx ZynqMP Display Port. Currently this file + is used as placeholder for driver. The main reason is to record + compatible string and calling power domain driver.
--
2.39.5
PATCH 16/18 Kconfig: gpio: add empty line
In reply to Johan JonkerRestyle by adding an empty line between configs.
--- drivers/gpio/Kconfig | 1 + 1 file changed, 1 insertion(+)
drivers/gpio/Kconfig +1 -0
@@ -756,6 +756,7 @@ config SPL_ADP5585_GPIO depends on SPL_DM_GPIO && SPL_I2C help Support ADP5585 GPIO expander in SPL. + config MPFS_GPIO bool "Enable Polarfire SoC GPIO driver" depends on DM_GPIO
--
2.39.5
PATCH 17/18 Kconfig: drivers: restyle remaining
In reply to Johan JonkerRestyle all Kconfigs for the rest of "drivers":
Menu entries : no space left
Menu attributes: 1 TAB
Help text : 1 TAB + 2 spaces
Replace '---help---' by 'help'
--- drivers/adc/Kconfig | 2 +- drivers/block/Kconfig | 8 +++--- drivers/bootcount/Kconfig | 4 +-- drivers/clk/Kconfig | 4 +-- drivers/clk/owl/Kconfig | 8 +++--- drivers/clk/renesas/Kconfig | 8 +++--- drivers/crypto/aspeed/Kconfig | 4 +-- drivers/crypto/fsl/Kconfig | 10 ++++---- drivers/ddr/fsl/Kconfig | 4 +-- drivers/dma/ti/Kconfig | 16 ++++++------ drivers/gpio/Kconfig | 48 +++++++++++++++++------------------ drivers/led/Kconfig | 2 +- drivers/memory/Kconfig | 16 ++++++------ drivers/mfd/Kconfig | 6 ++--- drivers/misc/Kconfig | 8 +++--- drivers/mmc/Kconfig | 8 +++--- drivers/mux/Kconfig | 12 ++++----- drivers/pci/Kconfig | 16 ++++++------ drivers/pci_endpoint/Kconfig | 8 +++--- drivers/phy/Kconfig | 14 +++++----- drivers/phy/qcom/Kconfig | 2 +- drivers/ram/aspeed/Kconfig | 10 ++++---- drivers/ram/octeon/Kconfig | 6 ++--- drivers/ram/stm32mp1/Kconfig | 36 +++++++++++++------------- drivers/reboot-mode/Kconfig | 18 ++++++------- drivers/rtc/Kconfig | 4 +-- drivers/serial/Kconfig | 16 ++++++------ drivers/smem/Kconfig | 30 +++++++++++----------- drivers/soc/ti/Kconfig | 4 +-- drivers/spi/Kconfig | 28 ++++++++++---------- drivers/spmi/Kconfig | 8 +++--- drivers/thermal/Kconfig | 32 +++++++++++------------ drivers/ufs/Kconfig | 4 +-- drivers/watchdog/Kconfig | 8 +++--- 34 files changed, 206 insertions(+), 206 deletions(-)
drivers/adc/Kconfig +1 -1
@@ -5,7 +5,7 @@ config ADC This enables ADC API for drivers, which allows driving ADC features by single and multi-channel methods for: - start/stop/get data for conversion of a single-channel selected by - a number or multi-channels selected by a bitmask + a number or multi-channels selected by a bitmask - get data mask (ADC resolution) ADC reference Voltage supply options: - methods for get Vdd/Vss reference Voltage values with polarity
drivers/block/Kconfig +4 -4
@@ -68,10 +68,10 @@ config BLKMAP bool "Composable virtual block devices (blkmap)" depends on BLK help - Create virtual block devices that are backed by various sources, - e.g. RAM, or parts of an existing block device. Though much more - rudimentary, it borrows a lot of ideas from Linux's device mapper - subsystem. + Create virtual block devices that are backed by various sources, + e.g. RAM, or parts of an existing block device. Though much more + rudimentary, it borrows a lot of ideas from Linux's device mapper + subsystem. Example use-cases: - Treat a region of RAM as a block device, i.e. a RAM disk. This let's
drivers/bootcount/Kconfig +2 -2
@@ -68,7 +68,7 @@ config BOOTCOUNT_ENV saveenv on all reboots, the environment variable "upgrade_available" is used. If "upgrade_available" is 0, "bootcount" is always 0. If "upgrade_available" is 1, - "bootcount" is incremented in the environment. + "bootcount" is incremented in the environment. So the Userspace Application must set the "upgrade_available" and "bootcount" variables to 0, if the system booted successfully.
@@ -83,7 +83,7 @@ config BOOTCOUNT_AT91 depends on AT91SAM9XE config DM_BOOTCOUNT - bool "Boot counter in a device-model device" + bool "Boot counter in a device-model device" help Enables reading/writing the bootcount in a device-model based backing store. If an entry in /chosen/u-boot,bootcount-device
drivers/clk/Kconfig +2 -2
@@ -134,8 +134,8 @@ config CLK_CDCE9XX bool "Enable CDCD9XX clock driver" depends on CLK && ARCH_OMAP2PLUS help - Enable the clock synthesizer driver for CDCE913/925/937/949 - series of chips. + Enable the clock synthesizer driver for CDCE913/925/937/949 + series of chips. config CLK_ICS8N3QV01 bool "Enable ICS8N3QV01 VCXO driver"
drivers/clk/owl/Kconfig +4 -4
@@ -1,8 +1,8 @@ config CLK_OWL - bool "Actions Semi OWL clock drivers" - depends on CLK && ARCH_OWL - help - Enable support for clock managemet unit present in Actions Semi + bool "Actions Semi OWL clock drivers" + depends on CLK && ARCH_OWL + help + Enable support for clock managemet unit present in Actions Semi Owl series S900/S700 SoCs.
drivers/clk/renesas/Kconfig +4 -4
@@ -61,11 +61,11 @@ config CLK_RCAR_GEN3 Enable this to support the clocks on Renesas R-Car Gen3 and Gen4 SoCs. config CLK_R8A774A1 - bool "Renesas R8A774A1 clock driver" + bool "Renesas R8A774A1 clock driver" def_bool y if R8A774A1 - depends on CLK_RCAR_GEN3 - help - Enable this to support the clocks on Renesas R8A774A1 SoC. + depends on CLK_RCAR_GEN3 + help + Enable this to support the clocks on Renesas R8A774A1 SoC. config CLK_R8A774B1 bool "Renesas R8A774B1 clock driver"
drivers/crypto/aspeed/Kconfig +2 -2
@@ -15,8 +15,8 @@ config ASPEED_ACRY bool "ASPEED RSA and ECC Engine" depends on ASPEED_AST2600 help - Select this option to enable a driver for using the RSA/ECC engine in - the ASPEED BMC SoCs. + Select this option to enable a driver for using the RSA/ECC engine in + the ASPEED BMC SoCs. Enabling this allows the use of RSA/ECC operations in hardware without requiring the software implementations. It also improves performance and saves code size.
drivers/crypto/fsl/Kconfig +5 -5
@@ -27,27 +27,27 @@ config CAAM_64BIT config SYS_FSL_HAS_SEC bool help - Enable Freescale Secure Boot and Trusted Architecture + Enable Freescale Secure Boot and Trusted Architecture config SYS_FSL_SEC_COMPAT_2 bool help - Secure boot and trust architecture compatible version 2 + Secure boot and trust architecture compatible version 2 config SYS_FSL_SEC_COMPAT_4 bool help - Secure boot and trust architecture compatible version 4 + Secure boot and trust architecture compatible version 4 config SYS_FSL_SEC_COMPAT_5 bool help - Secure boot and trust architecture compatible version 5 + Secure boot and trust architecture compatible version 5 config SYS_FSL_SEC_COMPAT_6 bool help - Secure boot and trust architecture compatible version 6 + Secure boot and trust architecture compatible version 6 config SYS_FSL_SEC_BE bool "Big-endian access to Freescale Secure Boot"
drivers/ddr/fsl/Kconfig +2 -2
@@ -21,12 +21,12 @@ if SYS_FSL_DDR || SYS_FSL_MMDC config SYS_FSL_DDR_BE bool help - Access DDR registers in big-endian + Access DDR registers in big-endian config SYS_FSL_DDR_LE bool help - Access DDR registers in little-endian + Access DDR registers in little-endian config FSL_DDR_BIST bool
drivers/dma/ti/Kconfig +8 -8
@@ -3,14 +3,14 @@ if ARCH_K3 config TI_K3_NAVSS_UDMA - bool "Texas Instruments UDMA" - depends on ARCH_K3 - select DEVRES - select DMA - select TI_K3_NAVSS_RINGACC - select TI_K3_PSIL - help - Support for UDMA used in K3 devices. + bool "Texas Instruments UDMA" + depends on ARCH_K3 + select DEVRES + select DMA + select TI_K3_NAVSS_RINGACC + select TI_K3_PSIL + help + Support for UDMA used in K3 devices. endif config TI_K3_PSIL
drivers/gpio/Kconfig +24 -24
94 lines not on this page · raw message
drivers/led/Kconfig +1 -1
@@ -133,7 +133,7 @@ config LED_GPIO config SPL_LED_GPIO bool "LED support for GPIO-connected LEDs in SPL" - depends on SPL_LED && SPL_DM_GPIO + depends on SPL_LED && SPL_DM_GPIO help This option is an SPL-variant of the LED_GPIO option. See the help of LED_GPIO for details.
drivers/memory/Kconfig +8 -8
@@ -44,15 +44,15 @@ config STM32_OMM This driver manages the muxing between the 2 OSPI busses and the 2 output ports. There are 4 possible muxing configurations: - direct mode (no multiplexing): OSPI1 output is on port 1 and OSPI2 - output is on port 2 + output is on port 2 - OSPI1 and OSPI2 are multiplexed over the same output port 1 - swapped mode (no multiplexing), OSPI1 output is on port 2, - OSPI2 output is on port 1 + OSPI2 output is on port 1 - OSPI1 and OSPI2 are multiplexed over the same output port 2 It also manages : - - the split of the memory area shared between the 2 OSPI instances. - - chip select selection override. - - the time between 2 transactions in multiplexed mode. + - the split of the memory area shared between the 2 OSPI instances. + - chip select selection override. + - the time between 2 transactions in multiplexed mode. config TI_AEMIF tristate "Texas Instruments AEMIF driver"
@@ -71,9 +71,9 @@ config TI_GPMC depends on MEMORY && CLK && OF_CONTROL help This driver is for the General Purpose Memory Controller (GPMC) - present on Texas Instruments SoCs (e.g. OMAP2+). GPMC allows - interfacing to a variety of asynchronous as well as synchronous - memory drives like NOR, NAND, OneNAND, SRAM. + present on Texas Instruments SoCs (e.g. OMAP2+). GPMC allows + interfacing to a variety of asynchronous as well as synchronous + memory drives like NOR, NAND, OneNAND, SRAM. if TI_GPMC config TI_GPMC_DEBUG
drivers/mfd/Kconfig +3 -3
@@ -1,4 +1,4 @@ config MFD_ATMEL_SMC - bool "Atmel Static Memory Controller driver" - help - Say yes here to support Atmel Static Memory Controller driver. + bool "Atmel Static Memory Controller driver" + help + Say yes here to support Atmel Static Memory Controller driver.
drivers/misc/Kconfig +4 -4
@@ -71,9 +71,9 @@ config ATSHA204A select BITREVERSE depends on MISC help - Enable support for I2C connected Atmel's ATSHA204A - CryptoAuthentication module found for example on the Turris Omnia - board. + Enable support for I2C connected Atmel's ATSHA204A + CryptoAuthentication module found for example on the Turris Omnia + board. config GATEWORKS_SC bool "Gateworks System Controller Support"
@@ -94,7 +94,7 @@ config QCOM_GENI etc. config ROCKCHIP_EFUSE - bool "Rockchip e-fuse support" + bool "Rockchip e-fuse support" depends on MISC help Enable (read-only) access for the e-fuse block found in Rockchip
drivers/mmc/Kconfig +4 -4
@@ -332,7 +332,7 @@ config MMC_MESON_GX bool "Meson GX EMMC controller support" depends on ARCH_MESON help - Support for EMMC host controller on Meson GX ARM SoCs platform (S905) + Support for EMMC host controller on Meson GX ARM SoCs platform (S905) config MMC_OWL bool "Actions OWL Multimedia Card Interface support"
@@ -659,8 +659,8 @@ config MMC_SDHCI_MSM depends on MMC_SDHCI && ARCH_SNAPDRAGON help Enables support for SDHCI 2.0 controller present on some Qualcomm - Snapdragon devices. This device is compatible with eMMC v4.5 and - SD 3.0 specifications. Both SD and eMMC devices are supported. + Snapdragon devices. This device is compatible with eMMC v4.5 and + SD 3.0 specifications. Both SD and eMMC devices are supported. Card-detect gpios are not supported. config MMC_SDHCI_MV
@@ -852,7 +852,7 @@ config FTSDC010_SDIO bool "Support ftsdc010 sdio" depends on FTSDC010 help - This can enable ftsdc010 sdio function. + This can enable ftsdc010 sdio function. config MMC_MTK bool "MediaTek SD/MMC Card Interface support"
drivers/mux/Kconfig +6 -6
@@ -5,17 +5,17 @@ config MULTIPLEXER depends on DM select DEVRES help - The mux framework is a minimalistic subsystem that handles multiplexer - controllers. It provides the same API as Linux and mux drivers should - be portable with a minimum effort. + The mux framework is a minimalistic subsystem that handles multiplexer + controllers. It provides the same API as Linux and mux drivers should + be portable with a minimum effort. if MULTIPLEXER config SPL_MUX_MMIO bool "MMIO register bitfield-controlled Multiplexer" - depends on MULTIPLEXER && SYSCON - help - MMIO register bitfield-controlled Multiplexer controller. + depends on MULTIPLEXER && SYSCON + help + MMIO register bitfield-controlled Multiplexer controller. The driver builds multiplexer controllers for bitfields in a syscon register. For N bit wide bitfields, there will be 2^N possible
drivers/pci/Kconfig +8 -8
@@ -101,11 +101,11 @@ config PCI_ENHANCED_ALLOCATION devices in place of traditional BARS for allocation of resources. config PCI_ARID - bool "Enable Alternate Routing-ID support for PCI" - help - Say Y here if you want to enable Alternate Routing-ID capability - support on PCI devices. This helps to skip some devices in BDF - scan that are not present. + bool "Enable Alternate Routing-ID support for PCI" + help + Say Y here if you want to enable Alternate Routing-ID capability + support on PCI devices. This helps to skip some devices in BDF + scan that are not present. config PCI_SCAN_SHOW bool "Show PCI devices during startup"
@@ -287,7 +287,7 @@ config PCI_IOMMU_EXTRA_MAPPINGS the node describing the PCI controller. The intent is to cover SR-IOV scenarios which need mappings for VFs and PCI hot-plug scenarios. More documentation can be found under: - arch/arm/cpu/armv8/fsl-layerscape/doc/README.pci_iommu_extra + arch/arm/cpu/armv8/fsl-layerscape/doc/README.pci_iommu_extra config PCIE_LAYERSCAPE_EP bool "Layerscape PCIe Endpoint mode support"
@@ -440,8 +440,8 @@ config PCIE_XILINX_NWL bool "Xilinx NWL PCIe controller" depends on ARCH_ZYNQMP help - Say 'Y' here if you want support for Xilinx / AMD NWL PCIe - controller as Root Port. + Say 'Y' here if you want support for Xilinx / AMD NWL PCIe + controller as Root Port. config PCIE_PLDA_COMMON bool
drivers/pci_endpoint/Kconfig +4 -4
@@ -9,10 +9,10 @@ config PCI_ENDPOINT bool "PCI Endpoint Support" depends on DM help - Enable this configuration option to support configurable PCI - endpoints. This should be enabled if the platform has a PCI - controllers that can operate in endpoint mode (as a device - connected to PCI host or bridge). + Enable this configuration option to support configurable PCI + endpoints. This should be enabled if the platform has a PCI + controllers that can operate in endpoint mode (as a device + connected to PCI host or bridge). config PCIE_CADENCE_EP bool "Cadence PCIe endpoint controller"
drivers/phy/Kconfig +7 -7
@@ -72,11 +72,11 @@ config AB8500_USB_PHY Support for the USB OTG PHY in ST-Ericsson AB8500. config APPLE_ATCPHY - bool "Apple Type-C PHY Driver" - depends on PHY && ARCH_APPLE - default y - help - Support for the Apple Type-C PHY. + bool "Apple Type-C PHY Driver" + depends on PHY && ARCH_APPLE + default y + help + Support for the Apple Type-C PHY. This is a dummy driver since the PHY is initialized sufficiently by previous stage firmware.
@@ -249,14 +249,14 @@ config MT7620_USB_PHY depends on PHY depends on SOC_MT7620 help - Support the intergated USB PHY in MediaTek MT7620 SoC + Support the intergated USB PHY in MediaTek MT7620 SoC config MT76X8_USB_PHY bool "MediaTek MT76x8 (7628/88) USB PHY support" depends on PHY depends on SOC_MT7628 help - Support the USB PHY in MT76x8 SoCs + Support the USB PHY in MT76x8 SoCs This PHY is found on MT76x8 devices supporting USB.
drivers/phy/qcom/Kconfig +1 -1
@@ -2,7 +2,7 @@ config MSM8916_USB_PHY bool select PHY help - Support the Qualcomm MSM8916 USB PHY + Support the Qualcomm MSM8916 USB PHY This PHY is found on qualcomm dragonboard410c development board.
drivers/ram/aspeed/Kconfig +5 -5
@@ -4,7 +4,7 @@ menuconfig ASPEED_RAM depends on ARCH_ASPEED || TARGET_ASPEED_AST2700_IBEX default ARCH_ASPEED help - Configuration options for DDR SDRAM on ASPEED systems. + Configuration options for DDR SDRAM on ASPEED systems. RAM initialisation is always built in for the platform. This menu allows customisation of the configuration used.
@@ -13,10 +13,10 @@ config ASPEED_DDR4_DUALX8 bool "Enable Dual X8 DDR4 die" depends on ASPEED_RAM help - Say Y if dual X8 DDR4 die is used on the board. The ASPEED DDRM - SRAM controller needs to know if the memory chip mounted on the - board is dual x8 die or not, otherwise it may get the wrong - size of the memory space. + Say Y if dual X8 DDR4 die is used on the board. The ASPEED DDRM + SRAM controller needs to know if the memory chip mounted on the + board is dual x8 die or not, otherwise it may get the wrong + size of the memory space. config ASPEED_BYPASS_SELFTEST depends on ASPEED_RAM
drivers/ram/octeon/Kconfig +3 -3
@@ -2,14 +2,14 @@ config RAM_OCTEON bool "Ram drivers for Octeon SoCs" depends on RAM && ARCH_OCTEON help - This enables support for RAM drivers for Octeon SoCs. + This enables support for RAM drivers for Octeon SoCs. if RAM_OCTEON config RAM_OCTEON_DDR4 bool "Octeon III DDR4 RAM support" help - This enables support for DDR4 RAM suppoort for Octeon III. This does - not include support for Octeon CN70XX. + This enables support for DDR4 RAM suppoort for Octeon III. This does + not include support for Octeon CN70XX. endif # RAM_OCTEON
drivers/ram/stm32mp1/Kconfig +18 -18
@@ -6,43 +6,43 @@ config STM32MP1_DDR select SPL_RAM if SPL default y help - activate STM32MP1 DDR controller driver for STM32MP1 soc - family: support for LPDDR2, LPDDR3 and DDR3 - the SDRAM parameters for controleur and phy need to be provided - in device tree (computed by DDR tuning tools) + activate STM32MP1 DDR controller driver for STM32MP1 soc + family: support for LPDDR2, LPDDR3 and DDR3 + the SDRAM parameters for controleur and phy need to be provided + in device tree (computed by DDR tuning tools) config STM32MP1_DDR_INTERACTIVE bool "STM32MP1 DDR driver : interactive support" depends on STM32MP1_DDR help - activate interactive support in STM32MP1 DDR controller driver - used for DDR tuning tools - to enter in intercative mode type 'd' during SPL DDR driver - initialisation + activate interactive support in STM32MP1 DDR controller driver + used for DDR tuning tools + to enter in intercative mode type 'd' during SPL DDR driver + initialisation config STM32MP1_DDR_INTERACTIVE_FORCE bool "STM32MP1 DDR driver : force interactive mode" depends on STM32MP1_DDR_INTERACTIVE help - force interactive mode in STM32MP1 DDR controller driver - skip the polling of character 'd' in console - useful when SPL is loaded in sysram - directly by programmer + force interactive mode in STM32MP1 DDR controller driver + skip the polling of character 'd' in console + useful when SPL is loaded in sysram + directly by programmer config STM32MP1_DDR_TESTS bool "STM32MP1 DDR driver : tests support" depends on STM32MP1_DDR_INTERACTIVE default y help - activate test support for interactive support in - STM32MP1 DDR controller driver: command test + activate test support for interactive support in + STM32MP1 DDR controller driver: command test config STM32MP1_DDR_TUNING bool "STM32MP1 DDR driver : support of tuning" depends on STM32MP1_DDR_INTERACTIVE default y help - activate tuning command in STM32MP1 DDR interactive mode - used for DDR tuning tools - - DQ Deskew algorithm - - DQS Trimming + activate tuning command in STM32MP1 DDR interactive mode + used for DDR tuning tools + - DQ Deskew algorithm + - DQS Trimming
drivers/reboot-mode/Kconfig +9 -9
@@ -11,26 +11,26 @@ config DM_REBOOT_MODE depends on DM select DEVRES help - Enable support for reboot mode control. This will allow users to - adjust the boot process based on reboot mode parameter - passed to U-Boot. + Enable support for reboot mode control. This will allow users to + adjust the boot process based on reboot mode parameter + passed to U-Boot. config DM_REBOOT_MODE_GPIO bool "Use GPIOs as reboot mode backend" depends on DM_REBOOT_MODE help - Use GPIOs to control the reboot mode. This will allow users to boot - a device in a specific mode by using a GPIO that can be controlled - outside U-Boot. + Use GPIOs to control the reboot mode. This will allow users to boot + a device in a specific mode by using a GPIO that can be controlled + outside U-Boot. config DM_REBOOT_MODE_RTC bool "Use RTC as reboot mode backend" depends on DM_RTC depends on DM_REBOOT_MODE help - Use RTC non volatile memory to control the reboot mode. This will allow users to boot - a device in a specific mode by using a register(s) that can be controlled - outside U-Boot (e.g. Kernel). + Use RTC non volatile memory to control the reboot mode. This will allow users to boot + a device in a specific mode by using a register(s) that can be controlled + outside U-Boot (e.g. Kernel). config REBOOT_MODE_NVMEM bool "Use NVMEM reboot mode"
drivers/rtc/Kconfig +2 -2
@@ -44,8 +44,8 @@ config VPL_DM_RTC config RTC_ENABLE_32KHZ_OUTPUT bool "Enable RTC 32Khz output" help - Some real-time clocks support the output of 32kHz square waves (such as ds3231), - the config symbol choose Real Time Clock device 32Khz output feature. + Some real-time clocks support the output of 32kHz square waves (such as ds3231), + the config symbol choose Real Time Clock device 32Khz output feature. config RTC_ARMADA38X bool "Enable Armada 38x Marvell SoC RTC"
drivers/serial/Kconfig +8 -8
@@ -759,11 +759,11 @@ config MVEBU_A3700_UART config MCFUART bool "Freescale ColdFire UART support" depends on M68K - help - Choose this option to add support for UART driver on the ColdFire - SoC's family. The serial communication channel provides a full-duplex - asynchronous/synchronous receiver and transmitter deriving an - operating frequency from the internal bus clock or an external clock. + help + Choose this option to add support for UART driver on the ColdFire + SoC's family. The serial communication channel provides a full-duplex + asynchronous/synchronous receiver and transmitter deriving an + operating frequency from the internal bus clock or an external clock. config MXC_UART bool "IMX serial port support"
@@ -1027,9 +1027,9 @@ config OCTEON_SERIAL_BOOTCMD select SYS_IS_IN_ENV select CONSOLE_MUX help - This driver supports remote input over the PCIe bus from a host - to U-Boot for entering commands. It is utilized by the host - commands 'oct-remote-load' and 'oct-remote-bootcmd'. + This driver supports remote input over the PCIe bus from a host + to U-Boot for entering commands. It is utilized by the host + commands 'oct-remote-load' and 'oct-remote-bootcmd'. config OCTEON_SERIAL_PCIE_CONSOLE bool "MIPS Octeon PCIe remote console"
drivers/smem/Kconfig +15 -15
@@ -4,22 +4,22 @@ menuconfig SMEM if SMEM config SANDBOX_SMEM - bool "Sandbox Shared Memory Manager (SMEM)" - depends on SANDBOX && DM - help - enable SMEM support for sandbox. This is an emulation of a real SMEM - manager. - The sandbox driver allocates a shared memory from the heap and - initialzies it on start. + bool "Sandbox Shared Memory Manager (SMEM)" + depends on SANDBOX && DM + help + enable SMEM support for sandbox. This is an emulation of a real SMEM + manager. + The sandbox driver allocates a shared memory from the heap and + initialzies it on start. config MSM_SMEM - bool "Qualcomm Shared Memory Manager (SMEM)" - depends on DM - depends on ARCH_SNAPDRAGON || ARCH_IPQ40XX - select DEVRES - help - Enable support for the Qualcomm Shared Memory Manager. - The driver provides an interface to items in a heap shared among all - processors in a Qualcomm platform. + bool "Qualcomm Shared Memory Manager (SMEM)" + depends on DM + depends on ARCH_SNAPDRAGON || ARCH_IPQ40XX + select DEVRES + help + Enable support for the Qualcomm Shared Memory Manager. + The driver provides an interface to items in a heap shared among all + processors in a Qualcomm platform. endif # menu "SMEM Support"
drivers/soc/ti/Kconfig +2 -2
@@ -21,8 +21,8 @@ config TI_KEYSTONE_SERDES bool "Keystone SerDes driver for ethernet" depends on ARCH_KEYSTONE help - SerDes driver for Keystone SoC used for ethernet support on TI - K2 platforms. + SerDes driver for Keystone SoC used for ethernet support on TI + K2 platforms. config TI_PRUSS bool "Support for TI's K3 based Pruss driver"
drivers/spi/Kconfig +14 -14
@@ -2,10 +2,10 @@ menuconfig SPI bool "SPI Support" help The "Serial Peripheral Interface" is a low level synchronous - protocol. Chips that support SPI can have data transfer rates - up to several tens of Mbit/sec. Chips are addressed with a - controller and a chipselect. Most SPI slaves don't support - dynamic device discovery; some are even write-only or read-only. + protocol. Chips that support SPI can have data transfer rates + up to several tens of Mbit/sec. Chips are addressed with a + controller and a chipselect. Most SPI slaves don't support + dynamic device discovery; some are even write-only or read-only. SPI is widely used by microcontrollers to talk with sensors, eeprom and flash memory, codecs and various other controller
@@ -200,11 +200,11 @@ config CADENCE_XSPI by using the Auto Command work mode. config CF_SPI - bool "ColdFire SPI driver" - depends on M68K - help - Enable the ColdFire SPI driver. This driver can be used on - some m68k SoCs. + bool "ColdFire SPI driver" + depends on M68K + help + Enable the ColdFire SPI driver. This driver can be used on + some m68k SoCs. config CV1800B_SPIF bool "Sophgo cv1800b SPI Flash Controller driver"
@@ -352,7 +352,7 @@ config MTK_SNOR select DEVRES help Enable the Mediatek SPINOR controller driver. This driver has - better read/write performance with NOR. + better read/write performance with NOR. config MTK_SNFI_SPI bool "Mediatek SPI memory controller driver"
@@ -544,8 +544,8 @@ config SPI_SIFIVE config SOFT_SPI bool "Soft SPI driver" help - Enable Soft SPI driver. This driver is to use GPIO simulate - the SPI protocol. + Enable Soft SPI driver. This driver is to use GPIO simulate + the SPI protocol. config SPI_SN_F_OSPI tristate "Socionext F_OSPI SPI flash controller"
@@ -673,8 +673,8 @@ config ZYNQMP_GQSPI config SPI_STACKED_PARALLEL bool "Enable support for stacked or parallel memories" help - Enable support for stacked/or parallel memories. This functionality - may appear on Xilinx hardware. By default this is disabled. + Enable support for stacked/or parallel memories. This functionality + may appear on Xilinx hardware. By default this is disabled. endif # if DM_SPI
drivers/spmi/Kconfig +4 -4
@@ -3,7 +3,7 @@ menu "SPMI support" config SPMI bool "Enable SPMI bus support" depends on DM - ---help--- + help Select this to enable to support SPMI bus. SPMI (System Power Management Interface) bus is used to connect PMIC devices on various SoCs.
@@ -11,13 +11,13 @@ config SPMI config SPMI_MSM bool "Support Qualcomm SPMI bus" depends on SPMI - ---help--- + help Support SPMI bus implementation found on Qualcomm Snapdragon SoCs. config SPMI_SANDBOX bool "Support for Sandbox SPMI bus" depends on SPMI - ---help--- + help Demo SPMI bus implementation. Emulates part of PM8916 as single - slave (0) on bus. It has 4 GPIO peripherals, pid 0xC0-0xC3. + slave (0) on bus. It has 4 GPIO peripherals, pid 0xC0-0xC3. endmenu
drivers/thermal/Kconfig +16 -16
@@ -13,9 +13,9 @@ config IMX_THERMAL depends on MX6 || MX7 help Support for Temperature Monitor (TEMPMON) found on Freescale i.MX SoCs. - It supports one critical trip point and one passive trip point. The - cpufreq is used as the cooling device to throttle CPUs when the - passive trip is crossed. + It supports one critical trip point and one passive trip point. The + cpufreq is used as the cooling device to throttle CPUs when the + passive trip is crossed. config IMX_SCU_THERMAL bool "Temperature sensor driver for NXP i.MX8"
@@ -27,11 +27,11 @@ config IMX_SCU_THERMAL trip is crossed config IMX_TMU - bool "Thermal Management Unit driver for NXP i.MX8M and iMX93" - depends on ARCH_IMX8M || IMX93 - help - Support for Temperature sensors on NXP i.MX8M and iMX93. - It supports one critical trip point and one passive trip point. + bool "Thermal Management Unit driver for NXP i.MX8M and iMX93" + depends on ARCH_IMX8M || IMX93 + help + Support for Temperature sensors on NXP i.MX8M and iMX93. + It supports one critical trip point and one passive trip point. The boot is hold to the cool device to throttle CPUs when the passive trip is crossed
@@ -44,15 +44,15 @@ config RCAR_GEN3_THERMAL driver into the U-Boot thermal framework. config TI_DRA7_THERMAL - bool "Temperature sensor driver for TI dra7xx SOCs" - help - Enable thermal support for the Texas Instruments DRA752 SoC family. - The driver supports reading CPU temperature. + bool "Temperature sensor driver for TI dra7xx SOCs" + help + Enable thermal support for the Texas Instruments DRA752 SoC family. + The driver supports reading CPU temperature. config TI_LM74_THERMAL - bool "Temperature sensor driver for TI LM74 chip" - help - Enable thermal support for the Texas Instruments LM74 chip. - The driver supports reading CPU temperature. + bool "Temperature sensor driver for TI LM74 chip" + help + Enable thermal support for the Texas Instruments LM74 chip. + The driver supports reading CPU temperature. endif # if DM_THERMAL
drivers/ufs/Kconfig +2 -2
@@ -19,7 +19,7 @@ config UFS_AMD_VERSAL2 config UFS_CADENCE bool "Cadence platform driver for UFS" depends on UFS - help + help This selects the platform driver for the Cadence UFS host controller present on present TI's J721e devices.
@@ -51,7 +51,7 @@ config UFS_PCI config UFS_QCOM bool "Qualcomm Host Controller driver for UFS" depends on UFS && ARCH_SNAPDRAGON - help + help This selects the platform driver for the UFS host controller present on Qualcomm Snapdragon SoCs.
drivers/watchdog/Kconfig +4 -4
@@ -383,10 +383,10 @@ config WDT_SBSA bool "SBSA watchdog timer support" depends on WDT help - Select this to enable SBSA watchdog timer. - This driver can operate ARM SBSA Generic Watchdog as a single stage. - In the single stage mode, when the timeout is reached, your system - will be reset by WS1. The first signal (WS0) is ignored. + Select this to enable SBSA watchdog timer. + This driver can operate ARM SBSA Generic Watchdog as a single stage. + In the single stage mode, when the timeout is reached, your system + will be reset by WS1. The first signal (WS0) is ignored. config WDT_SIEMENS_PMIC bool "Enable PMIC Watchdog Timer support for Siemens platforms"
--
2.39.5
PATCH 18/18 Kconfig: restyle
In reply to Johan JonkerRestyle Kconfig:
Menu entries : no space left
Menu attributes: 1 TAB
Help text : 1 TAB + 2 spaces
Replace '---help---' by 'help'
--- Kconfig | 14 +++++++------- 1 file changed, 7 insertions(+), 7 deletions(-)
Kconfig +7 -7
@@ -193,7 +193,7 @@ config FUZZ select ASAN help Enables the fuzzing infrastructure to generate fuzzing data and run - fuzz tests. + fuzz tests. config CC_HAS_ASM_INLINE def_bool $(success,echo 'void foo(void) { asm inline (""); }' | $(CC) -x c - -c -o /dev/null)
@@ -308,11 +308,11 @@ config SYS_MALLOC_F_LEN default 0x10000 if ARCH_IMX8 || ARCH_IMX8M default 0x2000 help - Size of the malloc() pool for use before relocation. If - this is defined, then a very simple malloc() implementation - will become available before relocation. The address is just - below the global data, and the stack is moved down to make - space. + Size of the malloc() pool for use before relocation. If + this is defined, then a very simple malloc() implementation + will become available before relocation. The address is just + below the global data, and the stack is moved down to make + space. This feature allocates regions with increasing addresses within the region. calloc() is supported, but realloc()
@@ -420,7 +420,7 @@ menuconfig EXPERT Use this only if you really know what you are doing. if EXPERT - config SYS_MALLOC_CLEAR_ON_INIT +config SYS_MALLOC_CLEAR_ON_INIT bool "Init with zeros the memory reserved for malloc (slow)" default y help
--
2.39.5
Quoted 8 lines · Johan Jonker
The
Kconfigmenu attribute '---help---' is deprecated. If we change to "help" the text has to indent. This again has to align with other attributes, so we have to restyle them as well.
And as there's a script then change allKconfigfiles excluding 'arch' and 'board' directories from part 1.[...]
Applied to u-boot/next, thanks!
[01/18] Kconfig: boot: restyle
commit: c28e57164d78a671338f1e59ba924190a66c9a55
[02/18] Kconfig: cmd: restyle
commit: 6f9303f33029a562c027d7c4d464c2a3daa57ff7
[03/18] Kconfig: common: restyle
commit: 89957a4f58192d68cc84a5ee5c3e6357edb228ae
[04/18] Kconfig: disk: restyle
commit: 7ffcbd87d2e664fcb6db3adf2efb5463ffff22c2
[05/18] Kconfig: dts: restyle
commit: 5bae190bde0ddd891560b76c9b8257a7b9246931
[06/18] Kconfig: fs: restyle
commit: 5c1ab62653eb772fc5e6d6db65c405fce44f86b0
[07/18] Kconfig: lib: restyle
commit: 8e85b5c761872d56d657b220134cf89c36103a10
[08/18] Kconfig: net: restyle
commit: 2b92ad862243f8052b66ac8b8b5e4cc2535cb6fc
[09/18] Kconfig: i2c: restyle
commit: 54cac2bf5cd53311d50b182d5885770126c8ce33
[10/18] Kconfig: mtd: restyle
commit: 11b7a94757954822d58316024f02a367bfdda99a
[11/18] Kconfig: net: restyle
commit: 2b92ad862243f8052b66ac8b8b5e4cc2535cb6fc
[12/18] Kconfig: pinctrl: restyle
commit: 591086d49d170aa32b851011f0c456082e5c2d48
[13/18] Kconfig: power: restyle
commit: b2c5dd6048caeac7a87175b0d7200565a9ae760a
[14/18] Kconfig: usb: restyle
commit: 8b09b702d488799ee42fbc7be3b8434e8a1c2fa0
[15/18] Kconfig: video: restyle
commit: 55ae284935295843ac6697e67425cc163756c1cf
[16/18] Kconfig: gpio: add empty line
commit: 173ffc7bcfbf6af70cd3b46a30110dad18278f72
[17/18] Kconfig: drivers: restyle remaining
commit: 145d58e2c7276f68195a7fc760457a5b88f867dd
[18/18] Kconfig: restyle
commit: 58ecf78d2bfe6f8255604397483953ceee52a035Signature · 1 line
Tom