Add minimal RISC-V Xen build and build testing
v3 cover Add minimal RISC-V Xen build and build testing
The patch series introduces the following:
- provide a minimal amount of changes to add initial RISC-V support to make Xen binary buildable and runnable for RISC-V architecture which can be used for future development and testing.
- add RISC-V 64 cross-compile build jobs to check if any new changes break RISC-V build.
Changes in V3:
- Remove include of <asm/config.h> from head.S.
Changes in V2:
- Remove the patch "automation: add cross-compiler support
for the build script" because it was reworked as a part of the patch series "CI: Fixes/cleanup in preparation for RISCV".
- Remove the patch "automation: add python3 package for riscv64.dockerfile" because it is not necessary for RISCV Xen binary build now.
- Rework the patch "arch/riscv: initial RISC-V support to build/run minimal Xen" according to the comments about v1 of the patch series.
- Add HYPERVISOR_ONLY to RISCV jobs in build.yaml after rebasing on "CI: Fixes/cleanup in preparation for RISCV" patch series.
Oleksii Kurochko (2):
arch/riscv: initial RISC-V support to build/run minimal Xen
automation: add RISC-V 64 cross-build tests for Xen
automation/gitlab-ci/build.yaml | 45 ++++++++ xen/arch/riscv/Makefile | 16 +++ xen/arch/riscv/arch.mk | 4 + xen/arch/riscv/include/asm/config.h | 9 +- xen/arch/riscv/riscv64/Makefile | 2 +- xen/arch/riscv/riscv64/head.S | 4 +- xen/arch/riscv/xen.lds.S | 158 ++++++++++++++++++++++++++++ 7 files changed, 233 insertions(+), 5 deletions(-) create mode 100644 xen/arch/riscv/xen.lds.S
Signature · 1 line
2.38.1
PATCH v3 1/2 arch/riscv: initial RISC-V support to build/run minimal Xen
The patch provides a minimal amount of changes to start build and run minimal Xen binary at GitLab CI&CD that will allow continuous checking of the build status of RISC-V Xen.
Except introduction of new files the following changes were done:
* Redefinition of ALIGN define from '.algin 2' to '.align 4' as RISC-V implementations (except for with C extension) enforce 32-bit instruction address alignment. With C extension, 16-bit and 32-bit are both allowed.
* ALL_OBJ-y and ALL_LIBS-y were temporary overwritted to produce a minimal hypervisor image otherwise it will be required to push huge amount of headers and stubs for common, drivers, libs etc which aren't necessary for now.
* Section changed from .text to .text.header for start function to make it the first one executed.
* Rework riscv64/Makefile logic to rebase over changes since the first RISC-V commit.
RISC-V Xen can be built by the following instructions:
$ CONTAINER=riscv64 ./automation/scripts/containerize \
make XEN_TARGET_ARCH=riscv64 tiny64_defconfig
$ CONTAINER=riscv64 ./automation/scripts/containerize \
make XEN_TARGET_ARCH=riscv64 -C xen buildRISC-V Xen can be run as:
$ qemu-system-riscv64 -M virt -smp 1 -nographic -m 2g \
-kernel xen/xenTo run in debug mode should be done the following instructions:
$ qemu-system-riscv64 -M virt -smp 1 -nographic -m 2g \
-kernel xen/xen -s -S
# In separate terminal:
$ riscv64-buildroot-linux-gnu-gdb
$ target remote :1234
$ add-symbol-file <xen_src>/xen/xen-syms 0x80200000
$ hb *0x80200000
$ c # it should stop at instruction j 0x80200000 <start>---
Changes in V3:
- Remove include of <asm/config.h> from head.S
---
Changes in V2:
- Update commit message:
- Add explanation why ALIGN define was changed.
- Add explanation why section of 'start' function was changed.
- Rework xen.lds.S linker script. It is mostly based on ARM except ARM-specific sections which have been removed.
- Rework in riscv64/Makefile rule $(TARGET)-syms
- Remove asm/types.h header as after reworking of riscv64/Makefile it is not needed now.
- Remove unneeded define SYMBOLS_DUMMY_OBJ.
--- xen/arch/riscv/Makefile | 16 +++ xen/arch/riscv/arch.mk | 4 + xen/arch/riscv/include/asm/config.h | 9 +- xen/arch/riscv/riscv64/Makefile | 2 +- xen/arch/riscv/riscv64/head.S | 4 +- xen/arch/riscv/xen.lds.S | 158 ++++++++++++++++++++++++++++ 6 files changed, 188 insertions(+), 5 deletions(-) create mode 100644 xen/arch/riscv/xen.lds.S
xen/arch/riscv/Makefile +16 -0
@@ -1,2 +1,18 @@ +obj-$(CONFIG_RISCV_64) += riscv64/ + +$(TARGET): $(TARGET)-syms + $(OBJCOPY) -O binary -S $< $@ + +$(TARGET)-syms: $(objtree)/prelink.o $(obj)/xen.lds + $(LD) $(XEN_LDFLAGS) -T $(obj)/xen.lds -N $< $(build_id_linker) -o $@ + $(NM) -pa --format=sysv $(@D)/$(@F) \ + | $(objtree)/tools/symbols --all-symbols --xensyms --sysv --sort \ + >$(@D)/$(@F).map + +$(obj)/xen.lds: $(src)/xen.lds.S FORCE + $(call if_changed_dep,cpp_lds_S) + +clean-files := $(objtree)/.xen-syms.[0-9]* + .PHONY: include include:
xen/arch/riscv/arch.mk +4 -0
@@ -11,3 +11,7 @@ riscv-march-$(CONFIG_RISCV_ISA_C) := $(riscv-march-y)c # -mcmodel=medlow would force Xen into the lower half. CFLAGS += -march=$(riscv-march-y) -mstrict-align -mcmodel=medany + +# TODO: Drop override when more of the build is working +override ALL_OBJS-y = arch/$(TARGET_ARCH)/built_in.o +override ALL_LIBS-y =
xen/arch/riscv/include/asm/config.h +8 -1
@@ -1,6 +1,9 @@#ifndef __RISCV_CONFIG_H__#define __RISCV_CONFIG_H__ +#include <xen/const.h> +#include <xen/page-size.h> +#if defined(CONFIG_RISCV_64 )# define LONG_BYTEORDER 3# define ELFSIZE 64
@@ -28,7 +31,7 @@/* Linkage for RISCV */ #ifdef __ASSEMBLY__ -#define ALIGN .align 2 +#define ALIGN .align 4#define ENTRY (name) \ .globl name; \
@@ -36,6 +39,10 @@ name:#endif +#define XEN_VIRT_START _AT(UL,0x00200000) + +#define SMP_CACHE_BYTES (1 << 6) +#endif /* __RISCV_CONFIG_H__ */ /* * Local variables:
xen/arch/riscv/riscv64/Makefile +1 -1
@@ -1 +1 @@ -extra-y += head.o +obj-y += head.o
xen/arch/riscv/riscv64/head.S +1 -3
@@ -1,6 +1,4 @@ -#include <asm/config.h> - - .text + .section .text.header, "ax", %progbits ENTRY(start) j start
xen/arch/riscv/xen.lds.S new file +158 -0
158 lines not on this page · raw message
Signature · 1 line
2.38.1
PATCH v3 2/2 automation: add RISC-V 64 cross-build tests for Xen
In reply to Oleksii KurochkoAdd build jobs to cross-compile Xen-only for RISC-V 64.
---
Changes in V2:
- Add HYPERVISOR_ONLY to RISCV jobs because after rebase on top of the patch series "CI: Fixes/cleanup in preparation for RISCV" it is required to set HYPERVISOR_ONLY in build.yaml
--- automation/gitlab-ci/build.yaml | 45 +++++++++++++++++++++++++++++++++ 1 file changed, 45 insertions(+)
automation/gitlab-ci/build.yaml +45 -0
@@ -172,6 +172,33 @@ variables: <<: *gcc +.riscv64-cross-build-tmpl: + <<: *build + variables: + XEN_TARGET_ARCH: riscv64 + tags: + - x86_64 + +.riscv64-cross-build: + extends: .riscv64-cross-build-tmpl + variables: + debug: n + +.riscv64-cross-build-debug: + extends: .riscv64-cross-build-tmpl + variables: + debug: y + +.gcc-riscv64-cross-build: + extends: .riscv64-cross-build + variables: + <<: *gcc + +.gcc-riscv64-cross-build-debug: + extends: .riscv64-cross-build-debug + variables: + <<: *gcc + # Jobs below this line archlinux-gcc:
@@ -617,6 +644,21 @@ alpine-3.12-gcc-debug-arm64-boot-cpupools: EXTRA_XEN_CONFIG: | CONFIG_BOOT_TIME_CPUPOOLS=y +# RISC-V 64 cross-build +riscv64-cross-gcc: + extends: .gcc-riscv64-cross-build + variables: + CONTAINER: archlinux:riscv64 + KBUILD_DEFCONFIG: tiny64_defconfig + HYPERVISOR_ONLY: y + +riscv64-cross-gcc-debug: + extends: .gcc-riscv64-cross-build-debug + variables: + CONTAINER: archlinux:riscv64 + KBUILD_DEFCONFIG: tiny64_defconfig + HYPERVISOR_ONLY: y + ## Test artifacts common .test-jobs-artifact-common:
@@ -692,3 +734,6 @@ kernel-5.10.74-export: - binaries/bzImage tags: - x86_64 + +# # RISC-V 64 test artificats +# # TODO: add RISC-V 64 test artitifacts
Signature · 1 line
2.38.1
Sorry for flooding but please skip review of patch series v3 as I missed comments of Andrew so only v4 should be reviewed.
Quoted 39 lines · Oleksii Kurochko
The patch series introduces the following:
- provide a minimal amount of changes to add initial RISC-V support to make Xen binary buildable and runnable for RISC-V architecture which can be used for future development and testing.
- add RISC-V 64 cross-compile build jobs to check if any new changes break RISC-V build.Changes in V3:
- Remove include of <asm/config.h> fromhead.S.Changes in V2:
- Remove the patch "automation: add cross-compiler support for the build script" because it was reworked as a part of the patch
series "CI: Fixes/cleanup in preparation for RISCV".
- Remove the patch "automation: add python3 package for riscv64.dockerfile"
because it is not necessary for RISCV Xen binary build now.
- Rework the patch "arch/riscv: initial RISC-V support to build/run minimal Xen" according to the comments about v1 of the patch series.
- AddHYPERVISOR_ONLYto RISCV jobs inbuild.yamlafter rebasing on "CI: Fixes/cleanup in preparation for RISCV" patch series.Oleksii Kurochko (2):
arch/riscv: initial RISC-V support to build/run minimal Xen
automation: add RISC-V 64 cross-build tests for Xenautomation/gitlab-ci/build.yaml | 45 ++++++++ xen/arch/riscv/Makefile | 16 +++ xen/arch/riscv/arch.mk | 4 +
xen/arch/riscv/include/asm/config.h| 9 +- xen/arch/riscv/riscv64/Makefile | 2 +- xen/arch/riscv/riscv64/head.S | 4 +- xen/arch/riscv/xen.lds.S | 158
++++++++++++++++++++++++++++7 files changed, 233 insertions(+), 5 deletions(-)create mode 100644
xen/arch/riscv/xen.lds.S