usb: host: dwc2: use driver model for PHY and CLOCK
v3 cover usb: host: dwc2: use driver model for PHY and CLOCK
In this serie I update the DWC2 host driver to use the device tree information and the associated PHY and CLOCK drivers when they are available.
CI-Travis build is OK for all target after V3:
https://travis-ci.org/patrickdelaunay/u-boot/builds/609496187
In V2, I cause the warnings for some boards:drivers/usb/host/built-in.o: In function `dwc2_usb_remove':drivers/usb/host/dwc2.c:1441: undefined reference to `clk_disable_bulk'
I test this serie on stm32mp157c-ev1 board, with PHY and CLK support
The U-CLASS are provided by:
- PHY by USBPHYC driver = ./drivers/phy/phy-stm32-usbphyc.c
- CLOCK by RCC clock driver = drivers/clk/clk_stm32mp1.c
- RESET by RCC reset driver = drivers/reset/stm32-reset.c
And I activate the configuration
+CONFIG_USB_DWC2=y
PS: it is not the default configuration to avoid conflict with gadget
driver
To solve a binding issue, I also deactivate the gadget support:
by default only one driver is bound to theusbotg_hs node with "snps,dwc2" compatible, and today it is the device one (the first in the driver list).
I also need to deactivate hnp-srp support with:
&usbotg_hs {
/* need to disable ONLY for HOST support */
hnp-srp-disable;
};WARNING: OTG with device or host support is not correctly handle by DWC2
driver (see example for dynamic OTG role in DWC3 driver).
The tests executed on the stm32mp157c-ev1 target:
STM32MP> usb start
starting USB...
Bus usb-otg at 49000000: USB DWC2
Bus usbh-ehci at 5800d000: USB EHCI 1.00
scanning bus usb-otg at 49000000 for devices... 2 USB Device(s) found scanning bus usbh-ehci at 5800d000 for devices... 3 USB Device(s) found
scanning usb for storage devices... 2 Storage Device(s) found
STM32MP> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
| U-Boot Root Hub
|
+-2 Mass Storage (480 Mb/s, 300mA)
Verbatim STORE N GO 070731C8ACD7EE97
1 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|
+-2 Hub (480 Mb/s, 2mA)
|
+-3 Mass Storage (480 Mb/s, 500mA)
Generic USB StorageSTM32MP> ls usb 0
<DIR> 4096 .
<DIR> 4096 ..
<DIR> 16384 lost+found
<DIR> 4096 record
1490212 xipImage
21058006 vmlinuxSTM32MP> load usb 0 0xC0000000 vmlinux
21058006 bytes read in 10851 ms (1.9 MiB/s)
Changes in v3:
- Add stub for clk_disable_bulk
Changes in v2:
- update dev_err
- update commit message
- change dev_err to dev_dbg for PHY function call
- treat dwc2_shutdown_phy error
- add clk_disable_bulk in dwc2_usb_remove
Patrick Delaunay (5):
dm: clk: add stub for clk_disable_bulk when CONFIG_CLK is desactivated
usb: host: dwc2: add phy support
usb: host: dwc2: add clk support
usb: host: dwc2: force reset assert
usb: host: dwc2: add trace to have clean usb start
drivers/usb/host/dwc2.c | 100 +++++++++++++++++++++++++++++++++++++++- include/clk.h | 4 ++ 2 files changed, 103 insertions(+), 1 deletion(-)
Signature · 1 line
2.17.1
PATCH v3 1/5 dm: clk: add stub for clk_disable_bulk when CONFIG_CLK is desactivated
Add stub for clk_disable_bulk() when CONFIG_CLK is desactivated.
That avoid compilation issue (undefined reference to `clk_disable_bulk') for code:
clk_disable_bulk(&priv->clks);clk_release_bulk(&priv->clks);
---
Changes in v3:
- Add stub for clk_disable_bulk
Changes in v2: None
include/clk.h | 4 ++++ 1 file changed, 4 insertions(+)
include/clk.h +4 -0
@@ -379,7 +379,11 @@ int clk_disable(struct clk *clk);* by clk_get_bulk(). * @return zero on success, or -ve error code. */ +#if CONFIG_IS_ENABLED (CLK )int clk_disable_bulk (struct clk_bulk *bulk); +#else +inline int clk_disable_bulk (struct clk_bulk *bulk) {return 0 ; } +#endif /** * clk_is_match - check if two clk's point to the same hardware clock
Signature · 1 line
2.17.1
PATCH v3 1/5 dm: clk: add stub for clk_disable_bulk when CONFIG_CLK is desactivated
Hi Patrick,
Quoted 24 lines · Patrick Delaunay
Add stub for
clk_disable_bulk()whenCONFIG_CLKis desactivated.That avoid compilation issue (undefined reference to `clk_disable_bulk') for code:
clk_disable_bulk(&priv->clks);clk_release_bulk(&priv->clks);Signed-off-by Patrick Delaunay <[email protected]>---
Changes in v3:
- Add stub forclk_disable_bulkChanges in v2: None
include/clk.h | 4 ++++ 1 file changed, 4 insertions(+)include/clk.h +0
-0
include/clk.h int clk_disable(struct clk *clk); · line 386
Quoted 8 lines
include/clk.h +4
-0@@ -379,7 +379,11 @@ int clk_disable(struct clk *clk);* by clk_get_bulk(). * @return zero on success, or -ve error code. */ +#if CONFIG_IS_ENABLED (CLK )int clk_disable_bulk (struct clk_bulk *bulk); +#else +inline int clk_disable_bulk (struct clk_bulk *bulk) {return 0 ; } +#endif
Maybe this could be done for all clk operations ?
JJ
Quoted 3 lines
include/clk.h +0
-0/** * clk_is_match - check if two clk's point to the same hardware clock
PATCH v3 1/5 dm: clk: add stub for clk_disable_bulk when CONFIG_CLK is desactivated
Hi Jean-Jacques,
Quoted 25 lines
From: Jean-Jacques Hiblot <[email protected]>
Sent: mardi 12 novembre 2019 11:17Hi Patrick,
Quoted 19 lines · Patrick Delaunay
Add stub for
clk_disable_bulk()whenCONFIG_CLKis desactivated.That avoid compilation issue (undefined reference to `clk_disable_bulk') for code:
clk_disable_bulk(&priv->clks);clk_release_bulk(&priv->clks);Signed-off-by Patrick Delaunay <[email protected]>---
Changes in v3:
- Add stub forclk_disable_bulkChanges in v2: None
include/clk.h | 4 ++++ 1 file changed, 4 insertions(+)
Quoted 15 lines
include/clk.h int clk_disable(struct clk *clk); · line 386
Quoted 13 lines
include/clk.h index renamed from include/clk.h +0
-0
a5ee53d94a..6f0b0fe4bc100644include/clk.h +4
-0@@ -379,7 +379,11 @@ int clk_disable(struct clk *clk);* by clk_get_bulk(). * @return zero on success, or -ve error code. */ +#if CONFIG_IS_ENABLED (CLK )int clk_disable_bulk (struct clk_bulk *bulk); +#else +inline int clk_disable_bulk (struct clk_bulk *bulk) {return 0 ; } +#endif Maybe this could be done for all clk operations ?
I think about, but after reflection
1/ stub already exist for :clk_get_by_indexclk_get_bulkclk_get_by_nameclk_release_all
=> just inline , return -ENOSYS
2/ clk_release_bulk inline call for clk_release_all
3/ other function (clk_request, clk_free, clk_get_rate, clk_enable, clk_disable)
should be not used as "clk" parameter is never valid / available if CONFIG_CLK is not activited
4/ the only remaining case is
int clk_disable_bulk(struct clk_bulk *bulk);
=> clk_get_bulk return -ENOSYS but normally this information is not keept by caller....
On error bulk.count = 0, and for me clk_disable_bulk(bulk wthou count = 0) is valid even if CONFIG_CLK is disable....
So I decide to limit the patch to this function to minimize the impacts also because the 2020.01 windows is closed.
Moreover I have not board to test CONFIG_CLK disabled.
But I agree : it is more clear a have a stub for other function which can be used
including clk_valid
=> I can propose a 2nd separate patch with this proposal if it is required.
Quoted 1 line
JJ
Regards
Patrick
PATCH v3 1/5 dm: clk: add stub for clk_disable_bulk when CONFIG_CLK is desactivated
In reply to Patrick DelaunayPatrick Delaunay <[email protected]> schrieb am Di., 12. Nov. 2019, 10:42:
Quoted 24 lines
Add stub for
clk_disable_bulk()whenCONFIG_CLKis desactivated.That avoid compilation issue (undefined reference to `clk_disable_bulk') for code:
clk_disable_bulk(&priv->clks);clk_release_bulk(&priv->clks);Signed-off-by Patrick Delaunay <[email protected]>---
Changes in v3:
- Add stub forclk_disable_bulkChanges in v2: None
include/clk.h | 4 ++++ 1 file changed, 4 insertions(+)include/clk.h +0
-0
include/clk.h int clk_disable(struct clk *clk); · line 387
Quoted 9 lines
include/clk.h +4
-0@@ -379,7 +379,11 @@ int clk_disable(struct clk *clk);* by clk_get_bulk(). * @return zero on success, or -ve error code. */ +#if CONFIG_IS_ENABLED (CLK )int clk_disable_bulk (struct clk_bulk *bulk); +#else +inline int clk_disable_bulk (struct clk_bulk *bulk) {return 0 ; } +#endif
Doing this inline at this place seems quite different than what is done for the other functions?
Regards,
Simon
Quoted 6 lines
include/clk.h +0
-1/** * clk_is_match - check if two clk's point to the same hardware clock -- 2.17.1
PATCH v3 1/5 dm: clk: add stub for clk_disable_bulk when CONFIG_CLK is desactivated
Hi Simon
Quoted 38 lines
De : Simon Goldschmidt <[email protected]> Envoyé : mardi 12 novembre 2019 11:40
Patrick Delaunay <[email protected]> schrieb am Di., 12. Nov. 2019, 10:42:
Add stub forclk_disable_bulk()whenCONFIG_CLKis desactivated.That avoid compilation issue (undefined reference to `clk_disable_bulk') for code:
clk_disable_bulk(&priv->clks);clk_release_bulk(&priv->clks);Signed-off-by Patrick Delaunay <[email protected]>---
Changes in v3:
- Add stub forclk_disable_bulkChanges in v2: None
include/clk.h| 4 ++++1 file changed, 4 insertions(+)include/clk.h +4
-0@@ -379,7 +379,11 @@ int clk_disable(struct clk *clk);* by clk_get_bulk(). * @return zero on success, or -ve error code. */ +#if CONFIG_IS_ENABLED (CLK )int clk_disable_bulk (struct clk_bulk *bulk); +#else +inline int clk_disable_bulk (struct clk_bulk *bulk) {return 0 ; } +#endif
Quoted 1 line
Doing this inline at this place seems quite different than what is done for the other functions?
which functions ?
I see:
static inline int clk_get_by_index(struct udevice *dev, int index,
struct clk *clk)
{
return -ENOSYS;
}
static inline int clk_set_defaults(struct udevice *dev) {
return 0;
}
But I agree, that it is a simplified stub....
Disable clk bulk if OK only if bulk.count ==0 but if should be always the case if CONFIG_CLK is disabled (as clk_get_bulk return -ENOSYS).
A more complete (better ?) stub is :
inline int clk_disable_bulk(struct clk_bulk *bulk) { if (bulk && bulk->count == 0) return 0;
else return -ENOSYS;
}
I think about a other solution:
inline int clk_disable_bulk(struct clk_bulk *bulk) { return -ENOSYS;
}
But that cause issue if the return value is tested by caller.
ret = clk_disable_bulk(bulk)
if (ret)
return ret;
Quoted 2 lines
Regards,
Simon
Regards
Patrick
Quoted 6 lines
/**
*clk_is_match- check if two clk's point to the same hardware clock
--
2.17.1
PATCH v3 2/5 usb: host: dwc2: add phy support
In reply to Patrick DelaunayUse generic phy to initialize the PHY associated to the DWC2 device and available in the device tree.
This patch don't added dependency because when CONFIG_PHY is not activated, the generic PHY function are stubbed.
---
Changes in v3: None
Changes in v2:
- update dev_err
- update commit message
- change dev_err to dev_dbg for PHY function call
- treat dwc2_shutdown_phy error
drivers/usb/host/dwc2.c | 66 +++++++++++++++++++++++++++++++++++++++++ 1 file changed, 66 insertions(+)
drivers/usb/host/dwc2.c +66 -0
@@ -7,6 +7,7 @@#include <common.h> #include <dm.h> #include <errno.h> +#include <generic-phy.h> #include <usb.h> #include <malloc.h> #include <memalign.h>
@@ -35,6 +36,7 @@ struct dwc2_priv {#ifdef CONFIG_DM_REGULATOR struct udevice *vbus_supply;#endif +struct phy phy;#else uint8_t *aligned_buffer;uint8_t *status_buffer;
@@ -1320,13 +1322,71 @@ static int dwc2_usb_ofdata_to_platdata(struct udevice *dev)return 0 ; } +static int dwc2_setup_phy (struct udevice *dev) +{ +struct dwc2_priv *priv =dev_get_priv (dev); +int ret; + + ret =generic_phy_get_by_index (dev,0 , &priv->phy); +if (ret) { +if (ret != -ENOENT ) { +dev_err (dev,"Failed to get USB PHY: %d.\n" , ret); +return ret; + } +return 0 ; + } + + ret =generic_phy_init (&priv->phy); +if (ret) { +dev_dbg (dev,"Failed to init USB PHY: %d.\n" , ret); +return ret; + } + + ret =generic_phy_power_on (&priv->phy); +if (ret) { +dev_dbg (dev,"Failed to power on USB PHY: %d.\n" , ret); +generic_phy_exit (&priv->phy); +return ret; + } + +return 0 ; +} + +static int dwc2_shutdown_phy (struct udevice *dev) +{ +struct dwc2_priv *priv =dev_get_priv (dev); +int ret; + +if (!generic_phy_valid (&priv->phy)) +return 0 ; + + ret =generic_phy_power_off (&priv->phy); +if (ret) { +dev_dbg (dev,"Failed to power off USB PHY: %d.\n" , ret); +return ret; + } + + ret =generic_phy_exit (&priv->phy); +if (ret) { +dev_dbg (dev,"Failed to power off USB PHY: %d.\n" , ret); +return ret; + } + +return 0 ; +} +static int dwc2_usb_probe (struct udevice *dev) {struct dwc2_priv *priv =dev_get_priv (dev);struct usb_bus_priv *bus_priv =dev_get_uclass_priv (dev); +int ret; bus_priv->desc_before_addr = true; + ret =dwc2_setup_phy (dev); +if (ret) +return ret; +return dwc2_init_common (dev, priv); }
@@ -1339,6 +1399,12 @@ static int dwc2_usb_remove(struct udevice *dev)if (ret)return ret; + ret =dwc2_shutdown_phy (dev); +if (ret) { +dev_dbg (dev,"Failed to shutdown USB PHY: %d.\n" , ret); +return ret; + } +dwc2_uninit_common (priv->regs);reset_release_bulk (&priv->resets);
Signature · 1 line
2.17.1
PATCH v3 3/5 usb: host: dwc2: add clk support
In reply to Patrick DelaunayAdd support for clock with driver model.
This patch don't added dependency because when CONFIG_CLK is not activated the clk function are stubbed.
---
Changes in v3: None
Changes in v2: None
drivers/usb/host/dwc2.c | 30 +++++++++++++++++++++++++++++- 1 file changed, 29 insertions(+), 1 deletion(-)
drivers/usb/host/dwc2.c +29 -1
@@ -5,13 +5,14 @@*/ #include <common.h> +#include <clk.h> #include <dm.h> #include <errno.h> #include <generic-phy.h> -#include <usb.h> #include <malloc.h> #include <memalign.h> #include <phys2bus.h> +#include <usb.h> #include <usbroothubdes.h> #include <wait_bit.h> #include <asm/io.h>
@@ -37,6 +38,7 @@ struct dwc2_priv {struct udevice *vbus_supply;#endif struct phy phy; +struct clk_bulk clks;#else uint8_t *aligned_buffer;uint8_t *status_buffer;
@@ -1375,6 +1377,26 @@ static int dwc2_shutdown_phy(struct udevice *dev)return 0 ; } +static int dwc2_clk_init (struct udevice *dev) +{ +struct dwc2_priv *priv =dev_get_priv (dev); +int ret; + + ret =clk_get_bulk (dev, &priv->clks); +if (ret == -ENOSYS || ret == -ENOENT ) +return 0 ; +if (ret) +return ret; + + ret =clk_enable_bulk (&priv->clks); +if (ret) { +clk_release_bulk (&priv->clks); +return ret; + } + +return 0 ; +} +static int dwc2_usb_probe (struct udevice *dev) {struct dwc2_priv *priv =dev_get_priv (dev);
@@ -1383,6 +1405,10 @@ static int dwc2_usb_probe(struct udevice *dev) bus_priv->desc_before_addr = true; + ret =dwc2_clk_init (dev); +if (ret) +return ret; + ret =dwc2_setup_phy (dev);if (ret)return ret;
@@ -1408,6 +1434,8 @@ static int dwc2_usb_remove(struct udevice *dev)dwc2_uninit_common (priv->regs);reset_release_bulk (&priv->resets); +clk_disable_bulk (&priv->clks); +clk_release_bulk (&priv->clks);return 0 ; }
Signature · 1 line
2.17.1
PATCH v3 4/5 usb: host: dwc2: force reset assert
In reply to Patrick DelaunayAssert reset before deassert in dwc2_reset;
this patch solve issues when the DWC2 registers are already initialized with value incompatible with host mode.
Force a hardware reset of the IP reset all the DWC2 registers at default value, the host driver start with a clean state (Core Soft reset doen in dwc_otg_core_reset is not enought
to reset all register).
The error can occurs in U-Boot when DWC2 device gadget driver force device mode (called by ums or dfu command, before to execute the usb start command).
---
Changes in v3: None
Changes in v2:
- add clk_disable_bulk in dwc2_usb_remove
drivers/usb/host/dwc2.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/usb/host/dwc2.c +2 -0
@@ -1149,6 +1149,8 @@ static int dwc2_reset(struct udevice *dev)return ret; } +/* force reset to clear all IP register */ +reset_assert_bulk (&priv->resets); ret =reset_deassert_bulk (&priv->resets);if (ret) {reset_release_bulk (&priv->resets);
Signature · 1 line
2.17.1
PATCH v3 5/5 usb: host: dwc2: add trace to have clean usb start
In reply to Patrick DelaunaySolve issue for the display of "usb start" command on stm32mp1 because one carriage return is missing in DWC2 probe.
STM32MP> usb start
starting USB...
Bus usb-otg at 49000000: Bus usbh-ehci at 5800d000: USB EHCI 1.00
after the patch:
STM32MP> usb start
starting USB...
Bus usb-otg at 49000000: USB DWC2
Bus usbh-ehci at 5800d000: USB EHCI 1.00
---
Changes in v3: None
Changes in v2: None
drivers/usb/host/dwc2.c | 2 ++ 1 file changed, 2 insertions(+)
drivers/usb/host/dwc2.c +2 -0
@@ -1217,6 +1217,8 @@ static int dwc2_init_common(struct udevice *dev, struct dwc2_priv *priv)if (readl (®s->gintsts) &DWC2_GINTSTS_CURMODE_HOST )mdelay (1000 ); +printf ("USB DWC2\n" ); +return 0 ; }
Signature · 1 line
2.17.1
v3 cover usb: host: dwc2: use driver model for PHY and CLOCK
In reply to Patrick DelaunayHi,
Quoted 107 lines
From: Patrick DELAUNAY <[email protected]>
Sent: mardi 12 novembre 2019 10:42
To: u-boot at lists.denx.de
Cc: ley.foon.tan at intel.com; b.galvani at gmail.com; simon.k.r.goldschmidt at gmail.com; Patrick DELAUNAY <[email protected]>; Jagan Teki <[email protected]>; Jean- Jacques Hiblot <[email protected]>; Lokesh Vutla <[email protected]>; Lukasz Majewski <[email protected]>; Marek Vasut <[email protected]>; Michal Suchanek <[email protected]>; Peng Fan <[email protected]>; Sekhar Nori <[email protected]>; Simon Glass <[email protected]>; Sven Schwermer <[email protected]>; U-Boot STM32 <uboot-stm32@st-md- mailman.stormreply.com>
Subject: [PATCH v3 0/5] usb: host: dwc2: use driver model for PHY and CLOCK
Importance: HighIn this serie I update the DWC2 host driver to use the device tree information and the associated PHY and CLOCK drivers when they are available.
CI-Travis build is OK for all target after V3:
https://travis-ci.org/patrickdelaunay/u-boot/builds/609496187In V2, I cause the warnings for some boards:
drivers/usb/host/built-in.o: In function `dwc2_usb_remove':drivers/usb/host/dwc2.c:1441: undefined reference to `clk_disable_bulk'I test this serie on stm32mp157c-ev1 board, with PHY and CLK support
The U-CLASS are provided by:
- PHY by USBPHYC driver =./drivers/phy/phy-stm32-usbphyc.c
- CLOCK by RCC clock driver =drivers/clk/clk_stm32mp1.c
- RESET by RCC reset driver =drivers/reset/stm32-reset.cAnd I activate the configuration
+CONFIG_USB_DWC2=yPS: it is not the default configuration to avoid conflict with gadget
driverTo solve a binding issue, I also deactivate the gadget support:
by default only one driver is bound totheusbotg_hsnode with "snps,dwc2" compatible, and today it is the device one (the first in the driver list).I also need to deactivate hnp-srp support with:
&usbotg_hs { /* need to disable ONLY for HOST support */ hnp-srp-disable; };WARNING: OTG with device or host support is not correctly handle by DWC2
driver (see example for dynamic OTG role in DWC3 driver).The tests executed on the stm32mp157c-ev1 target:
STM32MP> usb start
starting USB...
Bus usb-otg at 49000000: USB DWC2
Bus usbh-ehci at5800d000: USB EHCI 1.00
scanning bus usb-otg at 49000000 for devices... 2 USB Device(s) found scanning bus usbh-ehci at5800d000for devices... 3 USB Device(s) found
scanning usb for storage devices... 2 Storage Device(s) found
STM32MP> usb tree
USB device tree:
1 Hub (480 Mb/s, 0mA)
| U-Boot Root Hub
|
+-2 Mass Storage (480 Mb/s, 300mA)Verbatim STORE N GO 070731C8ACD7EE971 Hub (480 Mb/s, 0mA)
| u-boot EHCI Host Controller
|+-2 Hub (480 Mb/s, 2mA) | +-3 Mass Storage (480 Mb/s, 500mA) Generic USB StorageSTM32MP> ls usb 0
<DIR> 4096 .
<DIR> 4096 ..
<DIR> 16384 lost+found
<DIR> 4096 record1490212 xipImage 21058006 vmlinuxSTM32MP> load usb 0
0xC0000000vmlinux
21058006 bytes read in 10851 ms (1.9 MiB/s)Changes in v3:
- Add stub forclk_disable_bulkChanges in v2:
- updatedev_err
- update commit message
- changedev_errtodev_dbgfor PHY function call
- treatdwc2_shutdown_phyerror
- addclk_disable_bulkindwc2_usb_removePatrick Delaunay (5):
dm: clk: add stub forclk_disable_bulkwhenCONFIG_CLKis desactivated
usb: host: dwc2: add phy support
usb: host: dwc2: add clk support
usb: host: dwc2: force reset assert
usb: host: dwc2: add trace to have clean usb start
Quoted 7 lines
drivers/usb/host/dwc2.c | 100 +++++++++++++++++++++++++++++++++++++++- include/clk.h | 4 ++ 2 files changed, 103 insertions(+), 1 deletion(-)--
2.17.1
Any comments on this serie or I need to rebase it and resend the serie ?
http://patchwork.ozlabs.org/project/uboot/list/?series=142257
Sorry for the delay...
I miss the previous merge windows for v2020.01 and now I think it also the case for v2020.04 !
The previous version v2 was almost ready
http://patchwork.ozlabs.org/project/uboot/list/?series=141678&state=*
In v3 I only solve the compilation issue on some board with patch 1/5 (= http://patchwork.ozlabs.org/patch/1193397/)
PS: for other remarks I create a separate serie:
http://patchwork.ozlabs.org/project/uboot/list/?series=142260
Regards
Patrick
v3 cover usb: host: dwc2: use driver model for PHY and CLOCK
Quoted 1 line · Patrick DELAUNAY
Hi,
[...]
Quoted 8 lines
Quoted 7 lines
drivers/usb/host/dwc2.c | 100 +++++++++++++++++++++++++++++++++++++++- include/clk.h | 4 ++ 2 files changed, 103 insertions(+), 1 deletion(-)--
2.17.1
Quoted 6 lines
Any comments on this serie or I need to rebase it and resend the serie ?
http://patchwork.ozlabs.org/project/uboot/list/?series=142257
Sorry for the delay...
I miss the previous merge windows for v2020.01 and now I think it also the case for v2020.04 !
Please rebase and repost, thanks.
[...]
Signature · 2 lines
Best regards, Marek Vasut