Skip to contentSkip to conversation

net: phy: realtek: fix rtl8211e rx/tx delay config

PATCH In review Willy Liu 3 participants 8 messages Sep 17, 2020 – Sep 22, 2020

Subsystems (3)
lore
Share & tools
lore

Willy Liu

author
#0 lore raw

PATCH 1/1 net: phy: realtek: fix rtl8211e rx/tx delay config

RGMII RX Delay and TX Delay settings will not applied if Force TX RX Delay Control bit is not set.
Register bit for configuration pins:
13 = force Tx RX Delay controlled by bit12 bit11
12 = Tx Delay
11 = Rx Delay

Fixes f81dadbcf7fd ("net: phy: realtek: Add rtl8211e rx/tx delays config")
---
 drivers/net/phy/realtek.c | 20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)
 mode change 100644 => 100755 drivers/net/phy/realtek.c
drivers/net/phy/realtek.c +10 -10
old mode 100644
new mode 100755
index 95dbe5e..3fddd57
@@ -32,9 +32,9 @@
 #define RTL8211F_TX_DELAY			BIT(8)
 #define RTL8211F_RX_DELAY			BIT(3)
 
-#define RTL8211E_TX_DELAY			BIT(1)
-#define RTL8211E_RX_DELAY			BIT(2)
-#define RTL8211E_MODE_MII_GMII			BIT(3)
+#define RTL8211E_CTRL_DELAY			BIT(13)
+#define RTL8211E_TX_DELAY			BIT(12)
+#define RTL8211E_RX_DELAY			BIT(11)
 
 #define RTL8201F_ISR				0x1e
 #define RTL8201F_IER				0x13
@@ -249,13 +249,13 @@ static int rtl8211e_config_init(struct phy_device *phydev)
 		val = 0;
 		break;
 	case PHY_INTERFACE_MODE_RGMII_ID:
-		val = RTL8211E_TX_DELAY | RTL8211E_RX_DELAY;
+		val = RTL8211E_CTRL_DELAY | RTL8211E_TX_DELAY | RTL8211E_RX_DELAY;
 		break;
 	case PHY_INTERFACE_MODE_RGMII_RXID:
-		val = RTL8211E_RX_DELAY;
+		val = RTL8211E_CTRL_DELAY | RTL8211E_RX_DELAY;
 		break;
 	case PHY_INTERFACE_MODE_RGMII_TXID:
-		val = RTL8211E_TX_DELAY;
+		val = RTL8211E_CTRL_DELAY | RTL8211E_TX_DELAY;
 		break;
 	default: /* the rest of the modes imply leaving delays as is. */
 		return 0;
@@ -265,9 +265,8 @@ static int rtl8211e_config_init(struct phy_device *phydev)
 	 * 0xa4 extension page (0x7) layout. It can be used to disable/enable
 	 * the RX/TX delays otherwise controlled by RXDLY/TXDLY pins. It can
 	 * also be used to customize the whole configuration register:
-	 * 8:6 = PHY Address, 5:4 = Auto-Negotiation, 3 = Interface Mode Select,
-	 * 2 = RX Delay, 1 = TX Delay, 0 = SELRGV (see original PHY datasheet
-	 * for details).
+	 * 13 = Force Tx RX Delay controlled by bit12 bit11,
+	 * 12 = RX Delay, 11 = TX Delay
 	 */
 	oldpage = phy_select_page(phydev, 0x7);
 	if (oldpage < 0)
@@ -277,7 +276,8 @@ static int rtl8211e_config_init(struct phy_device *phydev)
 	if (ret)
 		goto err_restore_page;
 
-	ret = __phy_modify(phydev, 0x1c, RTL8211E_TX_DELAY | RTL8211E_RX_DELAY,
+	ret = __phy_modify(phydev, 0x1c, RTL8211E_CTRL_DELAY
+			   | RTL8211E_TX_DELAY | RTL8211E_RX_DELAY,
 			   val);
 
 err_restore_page:
Signature · 1 line
1.9.1
#1 lore raw

Hello Willy,
Thanks for the patch. My comments are below.

I've Cc'ed the U-boot/FreeBSD, who might be also interested in the solution you've provided.

Quoted 6 lines · Willy Liu

RGMII RX Delay and TX Delay settings will not applied if Force TX RX Delay Control bit is not set.
Register bit for configuration pins:
13 = force Tx RX Delay controlled by bit12 bit11
12 = Tx Delay
11 = Rx Delay

This is a very useful information, but it contradicts a bit to what knowledge we've currently got about that magical register. Current code in U-boot does the delays configuration by means of another bits:
https://elixir.bootlin.com/u-boot/v2020.10-rc4/source/drivers/net/phy/realtek.c

Could you provide a full register layout, so we'd know for sure what that register really does and finally close the question for good?

Quoted 15 lines
Fixes f81dadbcf7fd ("net: phy: realtek: Add rtl8211e rx/tx delays config")
---
 drivers/net/phy/realtek.c | 20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)
 mode change 100644 => 100755 drivers/net/phy/realtek.c
drivers/net/phy/realtek.c +0 -0
old mode 100644
new mode 100755
index 95dbe5e..3fddd57

drivers/net/phy/realtek.c line 38

Quoted 10 lines
drivers/net/phy/realtek.c +3 -3
@@ -32,9 +32,9 @@
 #define RTL8211F_TX_DELAY			BIT(8)
 #define RTL8211F_RX_DELAY			BIT(3)
 
 
-#define RTL8211E_TX_DELAY			BIT(1)
-#define RTL8211E_RX_DELAY			BIT(2)
-#define RTL8211E_MODE_MII_GMII			BIT(3)
+#define RTL8211E_CTRL_DELAY			BIT(13)
+#define RTL8211E_TX_DELAY			BIT(12)
+#define RTL8211E_RX_DELAY			BIT(11)

So, what do BIT(1) and BIT(2) control then? Could you explain?

Quoted 21 lines
drivers/net/phy/realtek.c +3 -3
 #define RTL8201F_ISR				0x1e
 #define RTL8201F_IER				0x13
@@ -249,13 +249,13 @@ static int rtl8211e_config_init(struct phy_device *phydev)
 		val = 0;
 		break;
 	case PHY_INTERFACE_MODE_RGMII_ID:
-		val = RTL8211E_TX_DELAY | RTL8211E_RX_DELAY;
+		val = RTL8211E_CTRL_DELAY | RTL8211E_TX_DELAY | RTL8211E_RX_DELAY;
 		break;
 	case PHY_INTERFACE_MODE_RGMII_RXID:
-		val = RTL8211E_RX_DELAY;
+		val = RTL8211E_CTRL_DELAY | RTL8211E_RX_DELAY;
 		break;
 	case PHY_INTERFACE_MODE_RGMII_TXID:
-		val = RTL8211E_TX_DELAY;
+		val = RTL8211E_CTRL_DELAY | RTL8211E_TX_DELAY;
 		break;
 	default: /* the rest of the modes imply leaving delays as is. */
 		return 0;

drivers/net/phy/realtek.c static int rtl8211e_config_init(struct phy_device *phydev) · line 270

Quoted 9 lines
drivers/net/phy/realtek.c +2 -3
@@ -265,9 +265,8 @@ static int rtl8211e_config_init(struct phy_device *phydev)
 	 * 0xa4 extension page (0x7) layout. It can be used to disable/enable
 	 * the RX/TX delays otherwise controlled by RXDLY/TXDLY pins. It can
 	 * also be used to customize the whole configuration register:
 
-	 * 8:6 = PHY Address, 5:4 = Auto-Negotiation, 3 = Interface Mode Select,
-	 * 2 = RX Delay, 1 = TX Delay, 0 = SELRGV (see original PHY datasheet
-	 * for details).
+	 * 13 = Force Tx RX Delay controlled by bit12 bit11,
+	 * 12 = RX Delay, 11 = TX Delay

Here you've removed the register layout description and replaced it with just three bits info. So from now the text above doesn't really corresponds to what follows.

I might have forgotten something, but AFAIR that register bits state mapped well to what was available on the corresponding external pins. So if you've got a sacred knowledge what configs are really hidden behind that register, please open it up. This in-code comment would be a good place to provide the full register description.

-Sergey

Quoted 16 lines
drivers/net/phy/realtek.c +0 -0
 	 */
 	oldpage = phy_select_page(phydev, 0x7);
drivers/net/phy/realtek.c +2 -1
 	if (oldpage < 0)
@@ -277,7 +276,8 @@ static int rtl8211e_config_init(struct phy_device *phydev)
 	if (ret)
 		goto err_restore_page;
 
-	ret = __phy_modify(phydev, 0x1c, RTL8211E_TX_DELAY | RTL8211E_RX_DELAY,
+	ret = __phy_modify(phydev, 0x1c, RTL8211E_CTRL_DELAY
+			   | RTL8211E_TX_DELAY | RTL8211E_RX_DELAY,
 			   val);
 
 err_restore_page:
Signature · 1 line
1.9.1
author
#2 lore raw

Hi Serge,
Thanks for your reply. There is a confidential issue that realtek doesn't offer the detail of a full register layout for configuration register.

The default setting for this configuration register should be 0x8148. Basically, no need to change it. If you need to enable RGMII RX Delay or RGMII TX Delay via register setting, you also need to enable Force Tx RX Delay controlled as well. 13 = force Tx RX Delay controlled by bit12 bit11
12 = Tx Delay
11 = Rx Delay

Current code in U-boot could change the register value from 0x8148 to 0xb548 (0x8148|0xb400). Bit12 and Bit13 are set, and RGMII TX delay enabled.
https://elixir.bootlin.com/u-boot/v2020.10-rc4/source/drivers/net/phy/realtek.c

I hope this information could help a bit.
B.R.
Willy

-----Original Message-----
From: Serge Semin <[email protected]>
Sent: Thursday, September 17, 2020 6:11 PM
To: 劉偉權 <[email protected]>
Cc: [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; Ryan Kao <[email protected]>; Kyle Evans <[email protected]>; Joe Hershberger <[email protected]>; Peter Robinson <[email protected]>
Subject: Re: [PATCH] net: phy: realtek: fix rtl8211e rx/tx delay config

Hello Willy,
Thanks for the patch. My comments are below.

I've Cc'ed the U-boot/FreeBSD, who might be also interested in the solution you've provided.

Quoted 6 lines · Willy Liu

RGMII RX Delay and TX Delay settings will not applied if Force TX RX Delay Control bit is not set.
Register bit for configuration pins:
13 = force Tx RX Delay controlled by bit12 bit11
12 = Tx Delay
11 = Rx Delay

This is a very useful information, but it contradicts a bit to what knowledge we've currently got about that magical register. Current code in U-boot does the delays configuration by means of another bits:
https://elixir.bootlin.com/u-boot/v2020.10-rc4/source/drivers/net/phy/realtek.c

Could you provide a full register layout, so we'd know for sure what that register really does and finally close the question for good?

Quoted 14 lines
Fixes f81dadbcf7fd ("net: phy: realtek: Add rtl8211e rx/tx delays

config")

---
 drivers/net/phy/realtek.c | 20 ++++++++++----------
 1 file changed, 10 insertions(+), 10 deletions(-)  mode change 100644 

=> 100755 drivers/net/phy/realtek.c

drivers/net/phy/realtek.c old renamed from drivers/net/phy/realtek.c +0 -0

mode 100644 new mode 100755 index 95dbe5e..3fddd57

drivers/net/phy/realtek.c line 38

Quoted 10 lines
drivers/net/phy/realtek.c +3 -3
@@ -32,9 +32,9 @@
 #define RTL8211F_TX_DELAY			BIT(8)
 #define RTL8211F_RX_DELAY			BIT(3)
 
 
-#define RTL8211E_TX_DELAY			BIT(1)
-#define RTL8211E_RX_DELAY			BIT(2)
-#define RTL8211E_MODE_MII_GMII			BIT(3)
+#define RTL8211E_CTRL_DELAY			BIT(13)
+#define RTL8211E_TX_DELAY			BIT(12)
+#define RTL8211E_RX_DELAY			BIT(11)

So, what do BIT(1) and BIT(2) control then? Could you explain?

Quoted 21 lines
drivers/net/phy/realtek.c +3 -3
 #define RTL8201F_ISR				0x1e
 #define RTL8201F_IER				0x13
@@ -249,13 +249,13 @@ static int rtl8211e_config_init(struct phy_device *phydev)
 		val = 0;
 		break;
 	case PHY_INTERFACE_MODE_RGMII_ID:
-		val = RTL8211E_TX_DELAY | RTL8211E_RX_DELAY;
+		val = RTL8211E_CTRL_DELAY | RTL8211E_TX_DELAY | RTL8211E_RX_DELAY;
 		break;
 	case PHY_INTERFACE_MODE_RGMII_RXID:
-		val = RTL8211E_RX_DELAY;
+		val = RTL8211E_CTRL_DELAY | RTL8211E_RX_DELAY;
 		break;
 	case PHY_INTERFACE_MODE_RGMII_TXID:
-		val = RTL8211E_TX_DELAY;
+		val = RTL8211E_CTRL_DELAY | RTL8211E_TX_DELAY;
 		break;
 	default: /* the rest of the modes imply leaving delays as is. */
 		return 0;

drivers/net/phy/realtek.c static int rtl8211e_config_init(struct phy_device *phydev) · line 270

Quoted 9 lines
drivers/net/phy/realtek.c +2 -3
@@ -265,9 +265,8 @@ static int rtl8211e_config_init(struct phy_device *phydev)
 	 * 0xa4 extension page (0x7) layout. It can be used to disable/enable
 	 * the RX/TX delays otherwise controlled by RXDLY/TXDLY pins. It can
 	 * also be used to customize the whole configuration register:
 
-	 * 8:6 = PHY Address, 5:4 = Auto-Negotiation, 3 = Interface Mode Select,
-	 * 2 = RX Delay, 1 = TX Delay, 0 = SELRGV (see original PHY datasheet
-	 * for details).
+	 * 13 = Force Tx RX Delay controlled by bit12 bit11,
+	 * 12 = RX Delay, 11 = TX Delay

Here you've removed the register layout description and replaced it with just three bits info. So from now the text above doesn't really corresponds to what follows.

I might have forgotten something, but AFAIR that register bits state mapped well to what was available on the corresponding external pins. So if you've got a sacred knowledge what configs are really hidden behind that register, please open it up. This in-code comment would be a good place to provide the full register description.

-Sergey

Quoted 14 lines
drivers/net/phy/realtek.c +0 -0
 	 */
 	oldpage = phy_select_page(phydev, 0x7);
drivers/net/phy/realtek.c +2 -2
 	if (oldpage < 0)
@@ -277,7 +276,8 @@ static int rtl8211e_config_init(struct phy_device *phydev)
 	if (ret)
 		goto err_restore_page;
 
-	ret = __phy_modify(phydev, 0x1c, RTL8211E_TX_DELAY | RTL8211E_RX_DELAY,
+	ret = __phy_modify(phydev, 0x1c, RTL8211E_CTRL_DELAY
+			   | RTL8211E_TX_DELAY | RTL8211E_RX_DELAY,
 			   val);
 
 err_restore_page:
--
Quoted 2 lines

1.9.1

------Please consider the environment before printing this e-mail.

maintainer
#3 lore raw
Quoted 5 lines · 劉偉權

Hi Serge,

Thanks for your reply. There is a confidential issue that realtek doesn't offer the detail of a full register layout for configuration register.

...

Quoted 15 lines

drivers/net/phy/realtek.c static int rtl8211e_config_init(struct phy_device *phydev) · line 269

Quoted 9 lines
drivers/net/phy/realtek.c +2 -3
 	 * 0xa4 extension page (0x7) layout. It can be used to disable/enable
 	 * the RX/TX delays otherwise controlled by RXDLY/TXDLY pins. It can
 	 * also be used to customize the whole configuration register:
 
-	 * 8:6 = PHY Address, 5:4 = Auto-Negotiation, 3 = Interface Mode Select,
-	 * 2 = RX Delay, 1 = TX Delay, 0 = SELRGV (see original PHY datasheet
-	 * for details).
+	 * 13 = Force Tx RX Delay controlled by bit12 bit11,
+	 * 12 = RX Delay, 11 = TX Delay

Here you've removed the register layout description and replaced itq with just three bits info. So from now the text above doesn't really corresponds to what follows.

Quoted 3 lines

I might have forgotten something, but AFAIR that register bits stateq mapped well to what was available on the corresponding external pins.

Hi Willy

So it appears bits 3 to 8 have been reverse engineered. Unless you know from your confidential datasheet that these are wrong, please leave the comment alone.

If you confidential datasheet says that the usage of bits 0-2 is wrong, then please do correct that part.

Andrew

#4 lore raw

Hello Andrew.

Quoted 31 lines · Andrew Lunn
Quoted 5 lines · 劉偉權

Hi Serge,

Thanks for your reply. There is a confidential issue that realtek doesn't offer the detail of a full register layout for configuration register.

...

Quoted 15 lines

drivers/net/phy/realtek.c static int rtl8211e_config_init(struct phy_device *phydev) · line 269

Quoted 9 lines
drivers/net/phy/realtek.c +2 -3
 	 * 0xa4 extension page (0x7) layout. It can be used to disable/enable
 	 * the RX/TX delays otherwise controlled by RXDLY/TXDLY pins. It can
 	 * also be used to customize the whole configuration register:
 
-	 * 8:6 = PHY Address, 5:4 = Auto-Negotiation, 3 = Interface Mode Select,
-	 * 2 = RX Delay, 1 = TX Delay, 0 = SELRGV (see original PHY datasheet
-	 * for details).
+	 * 13 = Force Tx RX Delay controlled by bit12 bit11,
+	 * 12 = RX Delay, 11 = TX Delay

Here you've removed the register layout description and replaced itq with just three bits info. So from now the text above doesn't really corresponds to what follows.

Quoted 3 lines

I might have forgotten something, but AFAIR that register bits stateq mapped well to what was available on the corresponding external pins.

Hi Willy

Quoted 6 lines

So it appears bits 3 to 8 have been reverse engineered. Unless you know from your confidential datasheet that these are wrong, please leave the comment alone.

If you confidential datasheet says that the usage of bits 0-2 is wrong, then please do correct that part.

I've got that info from Kyle post here:
https://reviews.freebsd.org/D13591

My work with that problem has been done more than a year ago, so I don't remember all the details. But IIRC the very first nine bits [8:0] must be a copy of what is set on the external configuration pins as I described in the comment. AFAIR I tried to manually change these pins [1] and detected that change right there in the register. That fully fitted to what Kyle wrote in his post. Alas I can't repeat it to be completely sure at the moment due to the lack of the hardware. So I might have missed something, and Willy' confirmation about that would have been more than welcome. What we can say now for sure I didn't use the magic number in my patch. That could have been a mistake from what Willy says in the commit-log...

Anyway aside with the Magic bits settings (which by Willy' patch appears to be the Tx/Rx delays + Force Tx/Rx delay setting) Kyle also clears the bits 1-2 with a comment "Ensure both internal delays are turned off". Willy, what can you say about that? Can we really leave them out from the change? Kyle, could you give us a comment about your experience with that?

[1] RTL8211E-VB-CG, RTL8211E-VL-CG, RTL8211E-VL-CG, "INTEGRATED 10/100/1000M ETHERNET TRANSCEIVER" Datasheet, Table 13. Configuration Register Definition, Rev. 1.6, 03 April 2012, Track ID: JATR-3375-16, p.16

-Sergey

Quoted 2 lines

Andrew

author
#5 lore raw

Hi Andrew,
I removed below register layout descriptions because these descriptions did not match register definitions for rtl8211e extension page 164 reg 0x1c at all.
8:6 = PHY Address
5:4 = Auto-Negotiation
3 = Mode
2 = RXD
1 = TXD
0 = SELRGV1
I think it is a misunderstanding. These definitions are mapped from datasheet rtl8211e table13" Configuration Register Definition". However this table should be HW pin configurations not register descriptions.

Users can config RXD/TXD via register setting(extension page 164 reg 0x1c). But bit map for these two settings should be below:
13 = Force Tx RX Delay controlled by bit12 bit11,
12 = RX Delay, 11 = TX Delay

Hi Sergey,
I saw the summary from https://reviews.freebsd.org/D13591. This patch is to reconfigure the RTL8211E used to force off TXD/RXD (RXD is defaulting to on, in my checks) and turn on some bits in the configuration register for this PHY that are undocumented.
The default value for "extension pg 0xa4 reg 0x1c" is 0x8148, and bit1-2 should be 0. In my opinion, this patch should be worked based on the magic number (0xb400). It seems RX delay was set and package did not lost for Some pine64 models. I am not sure if some models got different default value(not 0x8148) because the summary says (RXD is defaulting to on). What I mean is that this patch is actually turn on RX Delay not turn off RX delay. I hope we can correct the meaning of this register.

B.R.
Willy

-----Original Message-----
From: Serge Semin <[email protected]>
Sent: Friday, September 18, 2020 11:33 PM
To: Andrew Lunn <[email protected]>; Kyle Evans <[email protected]>; 劉偉權 <[email protected]>
Cc: [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; Ryan Kao <[email protected]>; Joe Hershberger <[email protected]>; Peter Robinson <[email protected]>
Subject: Re: [PATCH] net: phy: realtek: fix rtl8211e rx/tx delay config

Hello Andrew.

Quoted 31 lines · Andrew Lunn
Quoted 5 lines · 劉偉權

Hi Serge,

Thanks for your reply. There is a confidential issue that realtek doesn't offer the detail of a full register layout for configuration register.

...

Quoted 15 lines

drivers/net/phy/realtek.c static int rtl8211e_config_init(struct phy_device *phydev) · line 269

Quoted 9 lines
drivers/net/phy/realtek.c +2 -3
 	 * 0xa4 extension page (0x7) layout. It can be used to disable/enable
 	 * the RX/TX delays otherwise controlled by RXDLY/TXDLY pins. It can
 	 * also be used to customize the whole configuration register:
 
-	 * 8:6 = PHY Address, 5:4 = Auto-Negotiation, 3 = Interface Mode Select,
-	 * 2 = RX Delay, 1 = TX Delay, 0 = SELRGV (see original PHY datasheet
-	 * for details).
+	 * 13 = Force Tx RX Delay controlled by bit12 bit11,
+	 * 12 = RX Delay, 11 = TX Delay

Here you've removed the register layout description and replaced itq with just three bits info. So from now the text above doesn't really corresponds to what follows.

Quoted 3 lines

I might have forgotten something, but AFAIR that register bits stateq mapped well to what was available on the corresponding external pins.

Hi Willy

Quoted 6 lines

So it appears bits 3 to 8 have been reverse engineered. Unless you know from your confidential datasheet that these are wrong, please leave the comment alone.

If you confidential datasheet says that the usage of bits 0-2 is wrong, then please do correct that part.

I've got that info from Kyle post here:
https://reviews.freebsd.org/D13591

My work with that problem has been done more than a year ago, so I don't remember all the details. But IIRC the very first nine bits [8:0] must be a copy of what is set on the external configuration pins as I described in the comment.
AFAIR I tried to manually change these pins [1] and detected that change right there in the register. That fully fitted to what Kyle wrote in his post. Alas I can't repeat it to be completely sure at the moment due to the lack of the hardware. So I might have missed something, and Willy' confirmation about that would have been more than welcome. What we can say now for sure I didn't use the magic number in my patch. That could have been a mistake from what Willy says in the commit-log...

Anyway aside with the Magic bits settings (which by Willy' patch appears to be the Tx/Rx delays + Force Tx/Rx delay setting) Kyle also clears the bits 1-2 with a comment "Ensure both internal delays are turned off". Willy, what can you say about that? Can we really leave them out from the change? Kyle, could you give us a comment about your experience with that?

[1] RTL8211E-VB-CG, RTL8211E-VL-CG, RTL8211E-VL-CG, "INTEGRATED 10/100/1000M ETHERNET TRANSCEIVER" Datasheet, Table 13. Configuration Register Definition, Rev. 1.6, 03 April 2012, Track ID: JATR-3375-16, p.16

-Sergey

Quoted 2 lines

Andrew

------Please consider the environment before printing this e-mail.

maintainer
#6 lore raw
Quoted 12 lines · 劉偉權

Hi Andrew,

I removed below register layout descriptions because these descriptions did not match register definitions for rtl8211e extension page 164 reg 0x1c at all.
8:6 = PHY Address
5:4 = Auto-Negotiation
3 = Mode
2 = RXD
1 = TXD
0 = SELRGV1

Quoted 4 lines

I think it is a misunderstanding. These definitions are mapped from datasheet rtl8211e table13" Configuration Register Definition". However this table should be HW pin configurations not register descriptions.

So these are just how the device is strapped. So lets add that to the description, rather than remove it.

Quoted 7 lines

Users can config RXD/TXD via register setting(extension page 164 reg 0x1c). But bit map for these two settings should be below:
13 = Force Tx RX Delay controlled by bit12 bit11,
12 = RX Delay, 11 = TX Delay

Hi Sergey,

Quoted 8 lines

I saw the summary from https://reviews.freebsd.org/D13591. This patch is to reconfigure the RTL8211E used to force off TXD/RXD (RXD is defaulting to on, in my checks) and turn on some bits in the configuration register for this PHY that are undocumented.

The default value for "extension pg 0xa4 reg 0x1c" is 0x8148, and bit1-2 should be 0. In my opinion, this patch should be worked based on the magic number (0xb400).

Magic numbers are always bad. Please document what these bits mean.

Andrew

author
#7 lore raw

Hi Andrew,
I summary table 12,13 from RTL8211E-VB datasheet as below. [Table 12]
RTL8211E-VB Pin Pin Name

LED0                 PHYAD[0]
LED1                 PHYAD[1]
RXCTL                PHYAD[2]
RXD2                 AN[0]
RXD3                 AN[1]
 -                    Mode
LED2                 RX Delay
RXD1                 TX Delay
RXD0                 SELRGV

To set the CONFIG pins, an external pull-high or pull-low resistor is required. [Table 13]
PHYAD[2:0]: PHY Address
AN[1:0]: Auto-negotiation Configuration
Mode: Interface Mode select
RX Delay: RGMII Transmit clock timing control
1: Add 2ns delay to RXC for RXD latching(via 4.7k-ohm to 3.3V) 0: No delay(via 4.7k-ohm to GND)
TX Delay: RGMII Transmit clock timing control
1: Add 2ns delay to TXC for TXD latching(via 4.7k-ohm to 3.3V) 0: No delay(via 4.7k-ohm to GND)
SELRGV: 3.3V or 2.5V RGMII/GMII Selection

These two tables descript how to config it via external pull-high or pull-low resistor on PCB circuit.

Below patch gives table 13 another meaning and maps to register setting.
https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=f81dadbcf7fd06
8:6 = PHY Address
5:4 = Auto-Negotiation
3 = Interface Mode Select
2 = RX Delay
1 = TX Delay
0 = SELRGV
Sync from https://reviews.freebsd.org/D13591

Should I add how to config RX/TX Delay via pull high/down resistor in patch description?

Willy

-----Original Message-----
From: Andrew Lunn <[email protected]>
Sent: Monday, September 21, 2020 11:13 PM
To: 劉偉權 <[email protected]>
Cc: Serge Semin <[email protected]>; Kyle Evans <[email protected]>; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; [email protected]; Ryan Kao <[email protected]>; Joe Hershberger <[email protected]>; Peter Robinson <[email protected]>
Subject: Re: [PATCH] net: phy: realtek: fix rtl8211e rx/tx delay config

Quoted 12 lines · 劉偉權

Hi Andrew,

I removed below register layout descriptions because these descriptions did not match register definitions for rtl8211e extension page 164 reg 0x1c at all.
8:6 = PHY Address
5:4 = Auto-Negotiation
3 = Mode
2 = RXD
1 = TXD
0 = SELRGV1

Quoted 4 lines

I think it is a misunderstanding. These definitions are mapped from datasheet rtl8211e table13" Configuration Register Definition". However this table should be HW pin configurations not register descriptions.

So these are just how the device is strapped. So lets add that to the description, rather than remove it.

Quoted 7 lines

Users can config RXD/TXD via register setting(extension page 164 reg 0x1c). But bit map for these two settings should be below:
13 = Force Tx RX Delay controlled by bit12 bit11,
12 = RX Delay, 11 = TX Delay

Hi Sergey,

Quoted 8 lines

I saw the summary from https://reviews.freebsd.org/D13591. This patch is to reconfigure the RTL8211E used to force off TXD/RXD (RXD is defaulting to on, in my checks) and turn on some bits in the configuration register for this PHY that are undocumented.

The default value for "extension pg 0xa4 reg 0x1c" is 0x8148, and bit1-2 should be 0. In my opinion, this patch should be worked based on the magic number (0xb400).

Magic numbers are always bad. Please document what these bits mean.

Andrew

------Please consider the environment before printing this e-mail.