Skip to contentSkip to conversation

ARM: dts: realtek: Introduce syscon

PATCH In review Andreas Färber 3 participants 33 messages Dec 2, 2019 – Jan 15, 2020

Subsystems (3)
lore
Share & tools
lore
#0 lore raw

cover ARM: dts: realtek: Introduce syscon

Hello,

This patch series factors out system controller multi-function device nodes for CRT, Iso, Misc, SB2 and SCPU Wrapper IP blocks.

It was inspired by my SoC info RFC, as discussed in its cover letter [1].

Goal of DT is to describe the hardware, and in previous patches we've already introduced Realtek's r-bus as node layer. The next step here is to model multi-function blocks as nodes. In order to cope with 80-character line limit, child nodes are added via reference rather than in-place.

Also included is a patch adding a reset constant for the SB2 block added. We may need to follow up with bindings adding compatibles, clocks and resets.

This series is based on my RTD1195 v4 [2] (except for reset, rebased here), my RTD1395 v2 [3] and James' modified RTD1619 v3 [4].

The irq mux series v5 [5] has been rebased onto this series, v6 to be sent. The SoC info RFC series [1] is still being updated, v2 to be posted later.

Latest experimental patches at:
https://github.com/afaerber/linux/commits/rtd1295-next

Have a lot of fun!

Cheers,
Andreas

[1] https://patchwork.kernel.org/cover/11224261/
[2] https://patchwork.kernel.org/cover/11258949/
[3] https://patchwork.kernel.org/cover/11268955/
[4] https://patchwork.kernel.org/patch/11239697/
[5] https://patchwork.kernel.org/cover/11255291/

Andreas Färber (14):
ARM: dts: rtd1195: Introduce iso and misc syscon
arm64: dts: realtek: rtd129x: Introduce CRT, iso and misc syscon
arm64: dts: realtek: rtd139x: Introduce CRT, iso and misc syscon
arm64: dts: realtek: rtd16xx: Introduce iso and misc syscon
ARM: dts: rtd1195: Add CRT syscon node
dt-bindings: reset: Add Realtek RTD1195
ARM: dts: rtd1195: Add reset nodes
ARM: dts: rtd1195: Add UART resets
arm64: dts: realtek: rtd16xx: Add CRT syscon node
ARM: dts: rtd1195: Add SB2 and SCPU Wrapper syscon nodes
arm64: dts: realtek: rtd129x: Add SB2 and SCPU Wrapper syscon nodes
arm64: dts: realtek: rtd139x: Add SB2 and SCPU Wrapper syscon nodes
arm64: dts: realtek: rtd16xx: Add SB2 and SCPU Wrapper syscon nodes
dt-bindings: reset: rtd1295: Add SB2 reset

 arch/arm/boot/dts/rtd1195.dtsi              | 110 ++++++++++++++++---
 arch/arm64/boot/dts/realtek/rtd129x.dtsi    | 157 ++++++++++++++++++----------
 arch/arm64/boot/dts/realtek/rtd139x.dtsi    | 157 ++++++++++++++++++----------
 arch/arm64/boot/dts/realtek/rtd16xx.dtsi    |  91 ++++++++++++----
 include/dt-bindings/reset/realtek,rtd1195.h |  74 +++++++++++++
 include/dt-bindings/reset/realtek,rtd1295.h |   3 +
 6 files changed, 449 insertions(+), 143 deletions(-)
 create mode 100644 include/dt-bindings/reset/realtek,rtd1195.h
Signature · 1 line
2.16.4
#1 lore raw

PATCH 1/14 ARM: dts: rtd1195: Introduce iso and misc syscon

Group watchdog and UART0 into an Isolation syscon mfd node. Group UART1 into a Miscellaneous syscon mfd node.

---
 arch/arm/boot/dts/rtd1195.dtsi | 58 +++++++++++++++++++++++++++++-------------
 1 file changed, 40 insertions(+), 18 deletions(-)
arch/arm/boot/dts/rtd1195.dtsi +40 -18
index a8f7b9caacba..a74f530dc439 100644
@@ -100,28 +100,22 @@
 			#size-cells = <1>;
 			ranges = <0x0 0x18000000 0x70000>;
 
-			wdt: watchdog@7680 {
-				compatible = "realtek,rtd1295-watchdog";
-				reg = <0x7680 0x100>;
-				clocks = <&osc27M>;
-			};
-
-			uart0: serial@7800 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x7800 0x400>;
-				reg-shift = <2>;
+			iso: syscon@7000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x7000 0x1000>;
 				reg-io-width = <4>;
-				clock-frequency = <27000000>;
-				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x7000 0x1000>;
 			};
 
-			uart1: serial@1b200 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x1b200 0x100>;
-				reg-shift = <2>;
+			misc: syscon@1b000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1b000 0x1000>;
 				reg-io-width = <4>;
-				clock-frequency = <27000000>;
-				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1b000 0x1000>;
 			};
 		};
 
@@ -137,3 +131,31 @@
 		};
 	};
 };
+
+&iso {
+	wdt: watchdog@680 {
+		compatible = "realtek,rtd1295-watchdog";
+		reg = <0x680 0x100>;
+		clocks = <&osc27M>;
+	};
+
+	uart0: serial@800 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x800 0x400>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clock-frequency = <27000000>;
+		status = "disabled";
+	};
+};
+
+&misc {
+	uart1: serial@200 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x200 0x100>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clock-frequency = <27000000>;
+		status = "disabled";
+	};
+};
Signature · 7 lines
2.16.4


_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
#2 lore raw

PATCH 2/14 arm64: dts: realtek: rtd129x: Introduce CRT, iso and misc syscon

In reply to Andreas Färber

Group the non-iso reset controller nodes in a CRT syscon mfd node. Group reset controller, watchdog and UART0 in an Isolation syscon mfd node. Group UART1 and UART2 into a Miscellaneous syscon mfd node.

---
 arch/arm64/boot/dts/realtek/rtd129x.dtsi | 147 +++++++++++++++++++------------
 1 file changed, 90 insertions(+), 57 deletions(-)
arch/arm64/boot/dts/realtek/rtd129x.dtsi +90 -57
index 0de9e675be16..34dc09790d0b 100644
@@ -63,70 +63,31 @@
 			#size-cells = <1>;
 			ranges = <0x0 0x98000000 0x200000>;
 
-			reset1: reset-controller@0 {
-				compatible = "snps,dw-low-reset";
-				reg = <0x0 0x4>;
-				#reset-cells = <1>;
-			};
-
-			reset2: reset-controller@4 {
-				compatible = "snps,dw-low-reset";
-				reg = <0x4 0x4>;
-				#reset-cells = <1>;
-			};
-
-			reset3: reset-controller@8 {
-				compatible = "snps,dw-low-reset";
-				reg = <0x8 0x4>;
-				#reset-cells = <1>;
-			};
-
-			reset4: reset-controller@50 {
-				compatible = "snps,dw-low-reset";
-				reg = <0x50 0x4>;
-				#reset-cells = <1>;
-			};
-
-			iso_reset: reset-controller@7088 {
-				compatible = "snps,dw-low-reset";
-				reg = <0x7088 0x4>;
-				#reset-cells = <1>;
-			};
-
-			wdt: watchdog@7680 {
-				compatible = "realtek,rtd1295-watchdog";
-				reg = <0x7680 0x100>;
-				clocks = <&osc27M>;
-			};
-
-			uart0: serial@7800 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x7800 0x400>;
-				reg-shift = <2>;
+			crt: syscon@0 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x0 0x1800>;
 				reg-io-width = <4>;
-				clock-frequency = <27000000>;
-				resets = <&iso_reset RTD1295_ISO_RSTN_UR0>;
-				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x0 0x1800>;
 			};
 
-			uart1: serial@1b200 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x1b200 0x100>;
-				reg-shift = <2>;
+			iso: syscon@7000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x7000 0x1000>;
 				reg-io-width = <4>;
-				clock-frequency = <432000000>;
-				resets = <&reset2 RTD1295_RSTN_UR1>;
-				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x7000 0x1000>;
 			};
 
-			uart2: serial@1b400 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x1b400 0x100>;
-				reg-shift = <2>;
+			misc: syscon@1b000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1b000 0x1000>;
 				reg-io-width = <4>;
-				clock-frequency = <432000000>;
-				resets = <&reset2 RTD1295_RSTN_UR2>;
-				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1b000 0x1000>;
 			};
 		};
 
@@ -142,3 +103,75 @@
 		};
 	};
 };
+
+&crt {
+	reset1: reset-controller@0 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x0 0x4>;
+		#reset-cells = <1>;
+	};
+
+	reset2: reset-controller@4 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x4 0x4>;
+		#reset-cells = <1>;
+	};
+
+	reset3: reset-controller@8 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x8 0x4>;
+		#reset-cells = <1>;
+	};
+
+	reset4: reset-controller@50 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x50 0x4>;
+		#reset-cells = <1>;
+	};
+};
+
+&iso {
+	iso_reset: reset-controller@88 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x88 0x4>;
+		#reset-cells = <1>;
+	};
+
+	wdt: watchdog@680 {
+		compatible = "realtek,rtd1295-watchdog";
+		reg = <0x680 0x100>;
+		clocks = <&osc27M>;
+	};
+
+	uart0: serial@800 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x800 0x400>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clock-frequency = <27000000>;
+		resets = <&iso_reset RTD1295_ISO_RSTN_UR0>;
+		status = "disabled";
+	};
+};
+
+&misc {
+	uart1: serial@200 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x200 0x100>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clock-frequency = <432000000>;
+		resets = <&reset2 RTD1295_RSTN_UR1>;
+		status = "disabled";
+	};
+
+	uart2: serial@400 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x400 0x100>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clock-frequency = <432000000>;
+		resets = <&reset2 RTD1295_RSTN_UR2>;
+		status = "disabled";
+	};
+};
Signature · 1 line
2.16.4
maintainer Acked-by on v1 2/14
#3 lore raw

RE: [PATCH 02/14] arm64: dts: realtek: rtd129x: Introduce CRT, iso and misc syscon

Quoted 182 lines

Group the non-iso reset controller nodes in a CRT syscon mfd node. Group reset controller, watchdog and UART0 in an Isolation syscon mfd node. Group UART1 and UART2 into a Miscellaneous syscon mfd node.

---
 arch/arm64/boot/dts/realtek/rtd129x.dtsi | 147
+++++++++++++++++++------------
 1 file changed, 90 insertions(+), 57 deletions(-)
arch/arm64/boot/dts/realtek/rtd129x.dtsi +90 -58
index 0de9e675be16..34dc09790d0b 100644
@@ -63,70 +63,31 @@
 			#size-cells = <1>;
 			ranges = <0x0 0x98000000 0x200000>;
 
-			reset1: reset-controller@0 {
-				compatible = "snps,dw-low-reset";
-				reg = <0x0 0x4>;
-				#reset-cells = <1>;
-			};
-
-			reset2: reset-controller@4 {
-				compatible = "snps,dw-low-reset";
-				reg = <0x4 0x4>;
-				#reset-cells = <1>;
-			};
-
-			reset3: reset-controller@8 {
-				compatible = "snps,dw-low-reset";
-				reg = <0x8 0x4>;
-				#reset-cells = <1>;
-			};
-
-			reset4: reset-controller@50 {
-				compatible = "snps,dw-low-reset";
-				reg = <0x50 0x4>;
-				#reset-cells = <1>;
-			};
-
-			iso_reset: reset-controller@7088 {
-				compatible = "snps,dw-low-reset";
-				reg = <0x7088 0x4>;
-				#reset-cells = <1>;
-			};
-
-			wdt: watchdog@7680 {
-				compatible = "realtek,rtd1295-watchdog";
-				reg = <0x7680 0x100>;
-				clocks = <&osc27M>;
-			};
-
-			uart0: serial@7800 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x7800 0x400>;
-				reg-shift = <2>;
+			crt: syscon@0 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x0 0x1800>;
 				reg-io-width = <4>;
-				clock-frequency = <27000000>;
-				resets = <&iso_reset RTD1295_ISO_RSTN_UR0>;
-				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x0 0x1800>;
 			};
 
-			uart1: serial@1b200 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x1b200 0x100>;
-				reg-shift = <2>;
+			iso: syscon@7000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x7000 0x1000>;
 				reg-io-width = <4>;
-				clock-frequency = <432000000>;
-				resets = <&reset2 RTD1295_RSTN_UR1>;
-				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x7000 0x1000>;
 			};
 
-			uart2: serial@1b400 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x1b400 0x100>;
-				reg-shift = <2>;
+			misc: syscon@1b000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1b000 0x1000>;
 				reg-io-width = <4>;
-				clock-frequency = <432000000>;
-				resets = <&reset2 RTD1295_RSTN_UR2>;
-				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1b000 0x1000>;
 			};
 		};
 
@@ -142,3 +103,75 @@
 		};
 	};
 };
+
+&crt {
+	reset1: reset-controller@0 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x0 0x4>;
+		#reset-cells = <1>;
+	};
+
+	reset2: reset-controller@4 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x4 0x4>;
+		#reset-cells = <1>;
+	};
+
+	reset3: reset-controller@8 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x8 0x4>;
+		#reset-cells = <1>;
+	};
+
+	reset4: reset-controller@50 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x50 0x4>;
+		#reset-cells = <1>;
+	};
+};
+
+&iso {
+	iso_reset: reset-controller@88 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x88 0x4>;
+		#reset-cells = <1>;
+	};
+
+	wdt: watchdog@680 {
+		compatible = "realtek,rtd1295-watchdog";
+		reg = <0x680 0x100>;
+		clocks = <&osc27M>;
+	};
+
+	uart0: serial@800 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x800 0x400>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clock-frequency = <27000000>;
+		resets = <&iso_reset RTD1295_ISO_RSTN_UR0>;
+		status = "disabled";
+	};
+};
+
+&misc {
+	uart1: serial@200 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x200 0x100>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clock-frequency = <432000000>;
+		resets = <&reset2 RTD1295_RSTN_UR1>;
+		status = "disabled";
+	};
+
+	uart2: serial@400 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x400 0x100>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clock-frequency = <432000000>;
+		resets = <&reset2 RTD1295_RSTN_UR2>;
+		status = "disabled";
+	};
+};
--
Quoted 3 lines

2.16.4

#4 lore raw

PATCH 3/14 arm64: dts: realtek: rtd139x: Introduce CRT, iso and misc syscon

In reply to Andreas Färber

Group the non-iso reset controller nodes into a CRT syscon mfd node. Group reset controller, watchdog and UART0 into an Isolation mfd node. Group UART1 and UART2 into a Miscellaneous syscon mfd node.

---
 arch/arm64/boot/dts/realtek/rtd139x.dtsi | 147 +++++++++++++++++++------------
 1 file changed, 90 insertions(+), 57 deletions(-)
arch/arm64/boot/dts/realtek/rtd139x.dtsi +90 -57
index c11a505e43e2..3a571f3b7e38 100644
@@ -61,70 +61,31 @@
 			#size-cells = <1>;
 			ranges = <0x0 0x98000000 0x200000>;
 
-			reset1: reset-controller@0 {
-				compatible = "snps,dw-low-reset";
-				reg = <0x0 0x4>;
-				#reset-cells = <1>;
-			};
-
-			reset2: reset-controller@4 {
-				compatible = "snps,dw-low-reset";
-				reg = <0x4 0x4>;
-				#reset-cells = <1>;
-			};
-
-			reset3: reset-controller@8 {
-				compatible = "snps,dw-low-reset";
-				reg = <0x8 0x4>;
-				#reset-cells = <1>;
-			};
-
-			reset4: reset-controller@50 {
-				compatible = "snps,dw-low-reset";
-				reg = <0x50 0x4>;
-				#reset-cells = <1>;
-			};
-
-			iso_reset: reset-controller@7088 {
-				compatible = "snps,dw-low-reset";
-				reg = <0x7088 0x4>;
-				#reset-cells = <1>;
-			};
-
-			wdt: watchdog@7680 {
-				compatible = "realtek,rtd1295-watchdog";
-				reg = <0x7680 0x100>;
-				clocks = <&osc27M>;
-			};
-
-			uart0: serial@7800 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x7800 0x400>;
-				reg-shift = <2>;
+			crt: syscon@0 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x0 0x1000>;
 				reg-io-width = <4>;
-				clock-frequency = <27000000>;
-				resets = <&iso_reset RTD1295_ISO_RSTN_UR0>;
-				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x0 0x1000>;
 			};
 
-			uart1: serial@1b200 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x1b200 0x100>;
-				reg-shift = <2>;
+			iso: syscon@7000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x7000 0x1000>;
 				reg-io-width = <4>;
-				clock-frequency = <432000000>;
-				resets = <&reset2 RTD1295_RSTN_UR1>;
-				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x7000 0x1000>;
 			};
 
-			uart2: serial@1b400 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x1b400 0x100>;
-				reg-shift = <2>;
+			misc: syscon@1b000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1b000 0x1000>;
 				reg-io-width = <4>;
-				clock-frequency = <432000000>;
-				resets = <&reset2 RTD1295_RSTN_UR2>;
-				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1b000 0x1000>;
 			};
 		};
 
@@ -140,3 +101,75 @@
 		};
 	};
 };
+
+&crt {
+	reset1: reset-controller@0 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x0 0x4>;
+		#reset-cells = <1>;
+	};
+
+	reset2: reset-controller@4 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x4 0x4>;
+		#reset-cells = <1>;
+	};
+
+	reset3: reset-controller@8 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x8 0x4>;
+		#reset-cells = <1>;
+	};
+
+	reset4: reset-controller@50 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x50 0x4>;
+		#reset-cells = <1>;
+	};
+};
+
+&iso {
+	iso_reset: reset-controller@88 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x88 0x4>;
+		#reset-cells = <1>;
+	};
+
+	wdt: watchdog@680 {
+		compatible = "realtek,rtd1295-watchdog";
+		reg = <0x680 0x100>;
+		clocks = <&osc27M>;
+	};
+
+	uart0: serial@800 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x800 0x400>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clock-frequency = <27000000>;
+		resets = <&iso_reset RTD1295_ISO_RSTN_UR0>;
+		status = "disabled";
+	};
+};
+
+&misc {
+	uart1: serial@200 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x200 0x100>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clock-frequency = <432000000>;
+		resets = <&reset2 RTD1295_RSTN_UR1>;
+		status = "disabled";
+	};
+
+	uart2: serial@400 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x400 0x100>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clock-frequency = <432000000>;
+		resets = <&reset2 RTD1295_RSTN_UR2>;
+		status = "disabled";
+	};
+};
Signature · 1 line
2.16.4
maintainer Acked-by on v1 3/14
#5 lore raw

RE: [PATCH 03/14] arm64: dts: realtek: rtd139x: Introduce CRT, iso and misc syscon

Quoted 182 lines

Group the non-iso reset controller nodes into a CRT syscon mfd node. Group reset controller, watchdog and UART0 into an Isolation mfd node. Group UART1 and UART2 into a Miscellaneous syscon mfd node.

---
 arch/arm64/boot/dts/realtek/rtd139x.dtsi | 147
+++++++++++++++++++------------
 1 file changed, 90 insertions(+), 57 deletions(-)
arch/arm64/boot/dts/realtek/rtd139x.dtsi +90 -58
index c11a505e43e2..3a571f3b7e38 100644
@@ -61,70 +61,31 @@
 			#size-cells = <1>;
 			ranges = <0x0 0x98000000 0x200000>;
 
-			reset1: reset-controller@0 {
-				compatible = "snps,dw-low-reset";
-				reg = <0x0 0x4>;
-				#reset-cells = <1>;
-			};
-
-			reset2: reset-controller@4 {
-				compatible = "snps,dw-low-reset";
-				reg = <0x4 0x4>;
-				#reset-cells = <1>;
-			};
-
-			reset3: reset-controller@8 {
-				compatible = "snps,dw-low-reset";
-				reg = <0x8 0x4>;
-				#reset-cells = <1>;
-			};
-
-			reset4: reset-controller@50 {
-				compatible = "snps,dw-low-reset";
-				reg = <0x50 0x4>;
-				#reset-cells = <1>;
-			};
-
-			iso_reset: reset-controller@7088 {
-				compatible = "snps,dw-low-reset";
-				reg = <0x7088 0x4>;
-				#reset-cells = <1>;
-			};
-
-			wdt: watchdog@7680 {
-				compatible = "realtek,rtd1295-watchdog";
-				reg = <0x7680 0x100>;
-				clocks = <&osc27M>;
-			};
-
-			uart0: serial@7800 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x7800 0x400>;
-				reg-shift = <2>;
+			crt: syscon@0 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x0 0x1000>;
 				reg-io-width = <4>;
-				clock-frequency = <27000000>;
-				resets = <&iso_reset RTD1295_ISO_RSTN_UR0>;
-				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x0 0x1000>;
 			};
 
-			uart1: serial@1b200 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x1b200 0x100>;
-				reg-shift = <2>;
+			iso: syscon@7000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x7000 0x1000>;
 				reg-io-width = <4>;
-				clock-frequency = <432000000>;
-				resets = <&reset2 RTD1295_RSTN_UR1>;
-				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x7000 0x1000>;
 			};
 
-			uart2: serial@1b400 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x1b400 0x100>;
-				reg-shift = <2>;
+			misc: syscon@1b000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1b000 0x1000>;
 				reg-io-width = <4>;
-				clock-frequency = <432000000>;
-				resets = <&reset2 RTD1295_RSTN_UR2>;
-				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1b000 0x1000>;
 			};
 		};
 
@@ -140,3 +101,75 @@
 		};
 	};
 };
+
+&crt {
+	reset1: reset-controller@0 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x0 0x4>;
+		#reset-cells = <1>;
+	};
+
+	reset2: reset-controller@4 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x4 0x4>;
+		#reset-cells = <1>;
+	};
+
+	reset3: reset-controller@8 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x8 0x4>;
+		#reset-cells = <1>;
+	};
+
+	reset4: reset-controller@50 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x50 0x4>;
+		#reset-cells = <1>;
+	};
+};
+
+&iso {
+	iso_reset: reset-controller@88 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x88 0x4>;
+		#reset-cells = <1>;
+	};
+
+	wdt: watchdog@680 {
+		compatible = "realtek,rtd1295-watchdog";
+		reg = <0x680 0x100>;
+		clocks = <&osc27M>;
+	};
+
+	uart0: serial@800 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x800 0x400>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clock-frequency = <27000000>;
+		resets = <&iso_reset RTD1295_ISO_RSTN_UR0>;
+		status = "disabled";
+	};
+};
+
+&misc {
+	uart1: serial@200 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x200 0x100>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clock-frequency = <432000000>;
+		resets = <&reset2 RTD1295_RSTN_UR1>;
+		status = "disabled";
+	};
+
+	uart2: serial@400 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x400 0x100>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		clock-frequency = <432000000>;
+		resets = <&reset2 RTD1295_RSTN_UR2>;
+		status = "disabled";
+	};
+};
--
Quoted 3 lines

2.16.4

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#6 lore raw

PATCH 4/14 arm64: dts: realtek: rtd16xx: Introduce iso and misc syscon

In reply to Andreas Färber

Group UART0 into an Isolation syscon mfd node. Group UART1 and UART2 into a Miscellaneous syscon mfd node.

---
 arch/arm64/boot/dts/realtek/rtd16xx.dtsi | 70 +++++++++++++++++++++-----------
 1 file changed, 46 insertions(+), 24 deletions(-)
arch/arm64/boot/dts/realtek/rtd16xx.dtsi +46 -24
index 69cc0d941c8d..8f8f2b328cd1 100644
@@ -118,34 +118,22 @@
 			#size-cells = <1>;
 			ranges = <0x0 0x98000000 0x200000>;
 
-			uart0: serial0@7800 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x7800 0x400>;
-				reg-shift = <2>;
+			iso: syscon@7000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x7000 0x1000>;
 				reg-io-width = <4>;
-				interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
-				clock-frequency = <27000000>;
-				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x7000 0x1000>;
 			};
 
-			uart1: serial1@1b200 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x1b200 0x400>;
-				reg-shift = <2>;
+			misc: syscon@1b000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1b000 0x1000>;
 				reg-io-width = <4>;
-				interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
-				clock-frequency = <432000000>;
-				status = "disabled";
-			};
-
-			uart2: serial2@1b400 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x1b400 0x400>;
-				reg-shift = <2>;
-				reg-io-width = <4>;
-				interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
-				clock-frequency = <432000000>;
-				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1b000 0x1000>;
 			};
 		};
 
@@ -159,3 +147,37 @@
 		};
 	};
 };
+
+&iso {
+	uart0: serial0@800 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x800 0x400>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <27000000>;
+		status = "disabled";
+	};
+};
+
+&misc {
+	uart1: serial1@200 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x200 0x400>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <432000000>;
+		status = "disabled";
+	};
+
+	uart2: serial2@400 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x400 0x400>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <432000000>;
+		status = "disabled";
+	};
+};
Signature · 1 line
2.16.4
maintainer Acked-by on v1 4/14
#7 lore raw

RE: [PATCH 04/14] arm64: dts: realtek: rtd16xx: Introduce iso and misc syscon

Quoted 101 lines

Group UART0 into an Isolation syscon mfd node. Group UART1 and UART2 into a Miscellaneous syscon mfd node.

---
 arch/arm64/boot/dts/realtek/rtd16xx.dtsi | 70
+++++++++++++++++++++-----------
 1 file changed, 46 insertions(+), 24 deletions(-)
arch/arm64/boot/dts/realtek/rtd16xx.dtsi +46 -25
index 69cc0d941c8d..8f8f2b328cd1 100644
@@ -118,34 +118,22 @@
 			#size-cells = <1>;
 			ranges = <0x0 0x98000000 0x200000>;
 
-			uart0: serial0@7800 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x7800 0x400>;
-				reg-shift = <2>;
+			iso: syscon@7000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x7000 0x1000>;
 				reg-io-width = <4>;
-				interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
-				clock-frequency = <27000000>;
-				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x7000 0x1000>;
 			};
 
-			uart1: serial1@1b200 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x1b200 0x400>;
-				reg-shift = <2>;
+			misc: syscon@1b000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1b000 0x1000>;
 				reg-io-width = <4>;
-				interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
-				clock-frequency = <432000000>;
-				status = "disabled";
-			};
-
-			uart2: serial2@1b400 {
-				compatible = "snps,dw-apb-uart";
-				reg = <0x1b400 0x400>;
-				reg-shift = <2>;
-				reg-io-width = <4>;
-				interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
-				clock-frequency = <432000000>;
-				status = "disabled";
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1b000 0x1000>;
 			};
 		};
 
@@ -159,3 +147,37 @@
 		};
 	};
 };
+
+&iso {
+	uart0: serial0@800 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x800 0x400>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		interrupts = <GIC_SPI 68 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <27000000>;
+		status = "disabled";
+	};
+};
+
+&misc {
+	uart1: serial1@200 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x200 0x400>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		interrupts = <GIC_SPI 89 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <432000000>;
+		status = "disabled";
+	};
+
+	uart2: serial2@400 {
+		compatible = "snps,dw-apb-uart";
+		reg = <0x400 0x400>;
+		reg-shift = <2>;
+		reg-io-width = <4>;
+		interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+		clock-frequency = <432000000>;
+		status = "disabled";
+	};
+};
--
Quoted 3 lines

2.16.4

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#8 lore raw

PATCH 5/14 ARM: dts: rtd1195: Add CRT syscon node

In reply to Andreas Färber

Prepare a CRT syscon mfd node.

---
 arch/arm/boot/dts/rtd1195.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)
arch/arm/boot/dts/rtd1195.dtsi +9 -0
index a74f530dc439..ac37366ff7c4 100644
@@ -100,6 +100,15 @@
 			#size-cells = <1>;
 			ranges = <0x0 0x18000000 0x70000>;
 
+			crt: syscon@0 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x0 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x0 0x1000>;
+			};
+
 			iso: syscon@7000 {
 				compatible = "syscon", "simple-mfd";
 				reg = <0x7000 0x1000>;
Signature · 1 line
2.16.4
maintainer Acked-by on v1 5/14
#9 lore raw

RE: [PATCH 05/14] ARM: dts: rtd1195: Add CRT syscon node

Quoted 29 lines

Prepare a CRT syscon mfd node.

---
 arch/arm/boot/dts/rtd1195.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)
arch/arm/boot/dts/rtd1195.dtsi +9 -1
index a74f530dc439..ac37366ff7c4 100644
@@ -100,6 +100,15 @@
 			#size-cells = <1>;
 			ranges = <0x0 0x18000000 0x70000>;
 
+			crt: syscon@0 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x0 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x0 0x1000>;
+			};
+
 			iso: syscon@7000 {
 				compatible = "syscon", "simple-mfd";
 				reg = <0x7000 0x1000>;
--
Quoted 3 lines

2.16.4

#10 lore raw

PATCH 6/14 dt-bindings: reset: Add Realtek RTD1195

In reply to Andreas Färber

Add a header with symbolic reset indices for Realtek RTD1195 SoC. Naming was derived from BSP register description headers.

---
v1: From RTD1195 v4 series

 include/dt-bindings/reset/realtek,rtd1195.h | 74 +++++++++++++++++++++++++++++
 1 file changed, 74 insertions(+)
 create mode 100644 include/dt-bindings/reset/realtek,rtd1195.h
include/dt-bindings/reset/realtek,rtd1195.h new file +74 -0
new file mode 100644
index 000000000000..27902abf935b
@@ -0,0 +1,74 @@
+/* SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-2-Clause) */
+/*
+ * Realtek RTD1195 reset controllers
+ *
+ * Copyright (c) 2017 Andreas Färber
+ */
+#ifndef DT_BINDINGS_RESET_RTD1195_H
+#define DT_BINDINGS_RESET_RTD1195_H
+
+/* soft reset 1 */
+#define RTD1195_RSTN_MISC		0
+#define RTD1195_RSTN_RNG		1
+#define RTD1195_RSTN_USB3_POW		2
+#define RTD1195_RSTN_GSPI		3
+#define RTD1195_RSTN_USB3_P0_MDIO	4
+#define RTD1195_RSTN_VE_H265		5
+#define RTD1195_RSTN_USB		6
+#define RTD1195_RSTN_USB_PHY0		8
+#define RTD1195_RSTN_USB_PHY1		9
+#define RTD1195_RSTN_HDMIRX		11
+#define RTD1195_RSTN_HDMI		12
+#define RTD1195_RSTN_ETN		14
+#define RTD1195_RSTN_AIO		15
+#define RTD1195_RSTN_GPU		16
+#define RTD1195_RSTN_VE_H264		17
+#define RTD1195_RSTN_VE_JPEG		18
+#define RTD1195_RSTN_TVE		19
+#define RTD1195_RSTN_VO			20
+#define RTD1195_RSTN_LVDS		21
+#define RTD1195_RSTN_SE			22
+#define RTD1195_RSTN_DCU		23
+#define RTD1195_RSTN_DC_PHY		24
+#define RTD1195_RSTN_CP			25
+#define RTD1195_RSTN_MD			26
+#define RTD1195_RSTN_TP			27
+#define RTD1195_RSTN_AE			28
+#define RTD1195_RSTN_NF			29
+#define RTD1195_RSTN_MIPI		30
+
+/* soft reset 2 */
+#define RTD1195_RSTN_ACPU		0
+#define RTD1195_RSTN_VCPU		1
+#define RTD1195_RSTN_PCR		9
+#define RTD1195_RSTN_CR			10
+#define RTD1195_RSTN_EMMC		11
+#define RTD1195_RSTN_SDIO		12
+#define RTD1195_RSTN_I2C_5		18
+#define RTD1195_RSTN_RTC		20
+#define RTD1195_RSTN_I2C_4		23
+#define RTD1195_RSTN_I2C_3		24
+#define RTD1195_RSTN_I2C_2		25
+#define RTD1195_RSTN_I2C_1		26
+#define RTD1195_RSTN_UR1		28
+
+/* soft reset 3 */
+#define RTD1195_RSTN_SB2		0
+
+/* iso soft reset */
+#define RTD1195_ISO_RSTN_VFD		0
+#define RTD1195_ISO_RSTN_IR		1
+#define RTD1195_ISO_RSTN_CEC0		2
+#define RTD1195_ISO_RSTN_CEC1		3
+#define RTD1195_ISO_RSTN_DP		4
+#define RTD1195_ISO_RSTN_CBUSTX		5
+#define RTD1195_ISO_RSTN_CBUSRX		6
+#define RTD1195_ISO_RSTN_EFUSE		7
+#define RTD1195_ISO_RSTN_UR0		8
+#define RTD1195_ISO_RSTN_GMAC		9
+#define RTD1195_ISO_RSTN_GPHY		10
+#define RTD1195_ISO_RSTN_I2C_0		11
+#define RTD1195_ISO_RSTN_I2C_6		12
+#define RTD1195_ISO_RSTN_CBUS		13
+
+#endif
Signature · 1 line
2.16.4
maintainer Acked-by on v1 6/14
#11 lore raw

RE: [PATCH 06/14] dt-bindings: reset: Add Realtek RTD1195

Quoted 96 lines

Add a header with symbolic reset indices for Realtek RTD1195 SoC. Naming was derived from BSP register description headers.

---
v1: From RTD1195 v4 series

 include/dt-bindings/reset/realtek,rtd1195.h | 74
+++++++++++++++++++++++++++++
 1 file changed, 74 insertions(+)
 create mode 100644 include/dt-bindings/reset/realtek,rtd1195.h
include/dt-bindings/reset/realtek,rtd1195.h new file +74 -1
new file mode 100644
index 000000000000..27902abf935b
@@ -0,0 +1,74 @@
+/* SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-2-Clause) */
+/*
+ * Realtek RTD1195 reset controllers
+ *
+ * Copyright (c) 2017 Andreas Färber
+ */
+#ifndef DT_BINDINGS_RESET_RTD1195_H
+#define DT_BINDINGS_RESET_RTD1195_H
+
+/* soft reset 1 */
+#define RTD1195_RSTN_MISC		0
+#define RTD1195_RSTN_RNG		1
+#define RTD1195_RSTN_USB3_POW		2
+#define RTD1195_RSTN_GSPI		3
+#define RTD1195_RSTN_USB3_P0_MDIO	4
+#define RTD1195_RSTN_VE_H265		5
+#define RTD1195_RSTN_USB		6
+#define RTD1195_RSTN_USB_PHY0		8
+#define RTD1195_RSTN_USB_PHY1		9
+#define RTD1195_RSTN_HDMIRX		11
+#define RTD1195_RSTN_HDMI		12
+#define RTD1195_RSTN_ETN		14
+#define RTD1195_RSTN_AIO		15
+#define RTD1195_RSTN_GPU		16
+#define RTD1195_RSTN_VE_H264		17
+#define RTD1195_RSTN_VE_JPEG		18
+#define RTD1195_RSTN_TVE		19
+#define RTD1195_RSTN_VO			20
+#define RTD1195_RSTN_LVDS		21
+#define RTD1195_RSTN_SE			22
+#define RTD1195_RSTN_DCU		23
+#define RTD1195_RSTN_DC_PHY		24
+#define RTD1195_RSTN_CP			25
+#define RTD1195_RSTN_MD			26
+#define RTD1195_RSTN_TP			27
+#define RTD1195_RSTN_AE			28
+#define RTD1195_RSTN_NF			29
+#define RTD1195_RSTN_MIPI		30
+
+/* soft reset 2 */
+#define RTD1195_RSTN_ACPU		0
+#define RTD1195_RSTN_VCPU		1
+#define RTD1195_RSTN_PCR		9
+#define RTD1195_RSTN_CR			10
+#define RTD1195_RSTN_EMMC		11
+#define RTD1195_RSTN_SDIO		12
+#define RTD1195_RSTN_I2C_5		18
+#define RTD1195_RSTN_RTC		20
+#define RTD1195_RSTN_I2C_4		23
+#define RTD1195_RSTN_I2C_3		24
+#define RTD1195_RSTN_I2C_2		25
+#define RTD1195_RSTN_I2C_1		26
+#define RTD1195_RSTN_UR1		28
+
+/* soft reset 3 */
+#define RTD1195_RSTN_SB2		0
+
+/* iso soft reset */
+#define RTD1195_ISO_RSTN_VFD		0
+#define RTD1195_ISO_RSTN_IR		1
+#define RTD1195_ISO_RSTN_CEC0		2
+#define RTD1195_ISO_RSTN_CEC1		3
+#define RTD1195_ISO_RSTN_DP		4
+#define RTD1195_ISO_RSTN_CBUSTX		5
+#define RTD1195_ISO_RSTN_CBUSRX		6
+#define RTD1195_ISO_RSTN_EFUSE		7
+#define RTD1195_ISO_RSTN_UR0		8
+#define RTD1195_ISO_RSTN_GMAC		9
+#define RTD1195_ISO_RSTN_GPHY		10
+#define RTD1195_ISO_RSTN_I2C_0		11
+#define RTD1195_ISO_RSTN_I2C_6		12
+#define RTD1195_ISO_RSTN_CBUS		13
+
+#endif
--
Quoted 2 lines

2.16.4

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#12 lore raw

PATCH 7/14 ARM: dts: rtd1195: Add reset nodes

In reply to Andreas Färber

Add reset controller nodes for Realtek RTD1195 SoC.

---
v1: From RTD1195 v4 series (James wants to change the compatible string)

 arch/arm/boot/dts/rtd1195.dtsi | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)
arch/arm/boot/dts/rtd1195.dtsi +26 -0
index ac37366ff7c4..886845e52205 100644
@@ -141,7 +141,33 @@
 	};
 };
 
+&crt {
+	reset1: reset-controller@0 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x0 0x4>;
+		#reset-cells = <1>;
+	};
+
+	reset2: reset-controller@4 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x4 0x4>;
+		#reset-cells = <1>;
+	};
+
+	reset3: reset-controller@8 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x8 0x4>;
+		#reset-cells = <1>;
+	};
+};
+
 &iso {
+	iso_reset: reset-controller@88 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x88 0x4>;
+		#reset-cells = <1>;
+	};
+
 	wdt: watchdog@680 {
 		compatible = "realtek,rtd1295-watchdog";
 		reg = <0x680 0x100>;
Signature · 1 line
2.16.4
maintainer Acked-by on v1 7/14
#13 lore raw

RE: [PATCH 07/14] ARM: dts: rtd1195: Add reset nodes

Quoted 48 lines

Add reset controller nodes for Realtek RTD1195 SoC.

---
v1: From RTD1195 v4 series (James wants to change the compatible string)

 arch/arm/boot/dts/rtd1195.dtsi | 26 ++++++++++++++++++++++++++
 1 file changed, 26 insertions(+)
arch/arm/boot/dts/rtd1195.dtsi +26 -1
index ac37366ff7c4..886845e52205 100644
@@ -141,7 +141,33 @@
 	};
 };
 
+&crt {
+	reset1: reset-controller@0 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x0 0x4>;
+		#reset-cells = <1>;
+	};
+
+	reset2: reset-controller@4 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x4 0x4>;
+		#reset-cells = <1>;
+	};
+
+	reset3: reset-controller@8 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x8 0x4>;
+		#reset-cells = <1>;
+	};
+};
+
 &iso {
+	iso_reset: reset-controller@88 {
+		compatible = "snps,dw-low-reset";
+		reg = <0x88 0x4>;
+		#reset-cells = <1>;
+	};
+
 	wdt: watchdog@680 {
 		compatible = "realtek,rtd1295-watchdog";
 		reg = <0x680 0x100>;
--
Quoted 2 lines

2.16.4

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#14 lore raw

PATCH 8/14 ARM: dts: rtd1195: Add UART resets

In reply to Andreas Färber

Associate the UART nodes with the corresponding reset controller bits.

---
v1: From RTD1195 v4 series

 arch/arm/boot/dts/rtd1195.dtsi | 3 +++
 1 file changed, 3 insertions(+)
arch/arm/boot/dts/rtd1195.dtsi +3 -0
index 886845e52205..09acb99083c1 100644
@@ -8,6 +8,7 @@
 /memreserve/ 0x17fff000 0x00001000;
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/reset/realtek,rtd1195.h>
 
 / {
 	compatible = "realtek,rtd1195";
@@ -179,6 +180,7 @@
 		reg = <0x800 0x400>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
+		resets = <&iso_reset RTD1195_ISO_RSTN_UR0>;
 		clock-frequency = <27000000>;
 		status = "disabled";
 	};
@@ -190,6 +192,7 @@
 		reg = <0x200 0x100>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
+		resets = <&reset2 RTD1195_RSTN_UR1>;
 		clock-frequency = <27000000>;
 		status = "disabled";
 	};
Signature · 1 line
2.16.4
maintainer Acked-by on v1 8/14
#15 lore raw

RE: [PATCH 08/14] ARM: dts: rtd1195: Add UART resets

Quoted 38 lines

Associate the UART nodes with the corresponding reset controller bits.

---
v1: From RTD1195 v4 series

 arch/arm/boot/dts/rtd1195.dtsi | 3 +++
 1 file changed, 3 insertions(+)
arch/arm/boot/dts/rtd1195.dtsi +3 -1
index 886845e52205..09acb99083c1 100644
@@ -8,6 +8,7 @@
 /memreserve/ 0x17fff000 0x00001000;
 
 #include <dt-bindings/interrupt-controller/arm-gic.h>
+#include <dt-bindings/reset/realtek,rtd1195.h>
 
 / {
 	compatible = "realtek,rtd1195";
@@ -179,6 +180,7 @@
 		reg = <0x800 0x400>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
+		resets = <&iso_reset RTD1195_ISO_RSTN_UR0>;
 		clock-frequency = <27000000>;
 		status = "disabled";
 	};
@@ -190,6 +192,7 @@
 		reg = <0x200 0x100>;
 		reg-shift = <2>;
 		reg-io-width = <4>;
+		resets = <&reset2 RTD1195_RSTN_UR1>;
 		clock-frequency = <27000000>;
 		status = "disabled";
 	};
--
Quoted 3 lines

2.16.4

#16 lore raw

PATCH 9/14 arm64: dts: realtek: rtd16xx: Add CRT syscon node

In reply to Andreas Färber

Prepare a CRT syscon mfd node.

---
 arch/arm64/boot/dts/realtek/rtd16xx.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)
arch/arm64/boot/dts/realtek/rtd16xx.dtsi +9 -0
index 8f8f2b328cd1..776efc10bab2 100644
@@ -118,6 +118,15 @@
 			#size-cells = <1>;
 			ranges = <0x0 0x98000000 0x200000>;
 
+			crt: syscon@0 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x0 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x0 0x1000>;
+			};
+
 			iso: syscon@7000 {
 				compatible = "syscon", "simple-mfd";
 				reg = <0x7000 0x1000>;
Signature · 1 line
2.16.4
maintainer Acked-by on v1 9/14
#17 lore raw

RE: [PATCH 09/14] arm64: dts: realtek: rtd16xx: Add CRT syscon node

Quoted 30 lines

Prepare a CRT syscon mfd node.

---
 arch/arm64/boot/dts/realtek/rtd16xx.dtsi | 9 +++++++++
 1 file changed, 9 insertions(+)
arch/arm64/boot/dts/realtek/rtd16xx.dtsi +9 -1
index 8f8f2b328cd1..776efc10bab2 100644
@@ -118,6 +118,15 @@
 			#size-cells = <1>;
 			ranges = <0x0 0x98000000 0x200000>;
 
+			crt: syscon@0 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x0 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x0 0x1000>;
+			};
+
 			iso: syscon@7000 {
 				compatible = "syscon", "simple-mfd";
 				reg = <0x7000 0x1000>;
--
Quoted 3 lines

2.16.4

#18 lore raw

PATCH 10/14 ARM: dts: rtd1195: Add SB2 and SCPU Wrapper syscon nodes

In reply to Andreas Färber

Add syscon mfd nodes for SB2 and SCPU Wrapper to RTD1195 DT.

---
 arch/arm/boot/dts/rtd1195.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
arch/arm/boot/dts/rtd1195.dtsi +18 -0
index 09acb99083c1..21897210d9d0 100644
@@ -119,6 +119,15 @@
 				ranges = <0x0 0x7000 0x1000>;
 			};
 
+			sb2: syscon@1a000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1a000 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1a000 0x1000>;
+			};
+
 			misc: syscon@1b000 {
 				compatible = "syscon", "simple-mfd";
 				reg = <0x1b000 0x1000>;
@@ -127,6 +136,15 @@
 				#size-cells = <1>;
 				ranges = <0x0 0x1b000 0x1000>;
 			};
+
+			scpu_wrapper: syscon@1d000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1d000 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1d000 0x1000>;
+			};
 		};
 
 		gic: interrupt-controller@ff011000 {
Signature · 1 line
2.16.4
maintainer Acked-by on v1 10/14
#19 lore raw

RE: [PATCH 10/14] ARM: dts: rtd1195: Add SB2 and SCPU Wrapper syscon nodes

Quoted 45 lines

Add syscon mfd nodes for SB2 and SCPU Wrapper to RTD1195 DT.

---
 arch/arm/boot/dts/rtd1195.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
arch/arm/boot/dts/rtd1195.dtsi +18 -1
index 09acb99083c1..21897210d9d0 100644
@@ -119,6 +119,15 @@
 				ranges = <0x0 0x7000 0x1000>;
 			};
 
+			sb2: syscon@1a000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1a000 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1a000 0x1000>;
+			};
+
 			misc: syscon@1b000 {
 				compatible = "syscon", "simple-mfd";
 				reg = <0x1b000 0x1000>;
@@ -127,6 +136,15 @@
 				#size-cells = <1>;
 				ranges = <0x0 0x1b000 0x1000>;
 			};
+
+			scpu_wrapper: syscon@1d000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1d000 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1d000 0x1000>;
+			};
 		};
 
 		gic: interrupt-controller@ff011000 {
--
Quoted 3 lines

2.16.4

#20 lore raw

PATCH 11/14 arm64: dts: realtek: rtd129x: Add SB2 and SCPU Wrapper syscon nodes

In reply to Andreas Färber

Add syscon mfd nodes for SB2 and SCPU Wrapper to RTD129x DT.

---
 arch/arm64/boot/dts/realtek/rtd129x.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
arch/arm64/boot/dts/realtek/rtd129x.dtsi +18 -0
index 34dc09790d0b..39aefe66a794 100644
@@ -81,6 +81,15 @@
 				ranges = <0x0 0x7000 0x1000>;
 			};
 
+			sb2: syscon@1a000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1a000 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1a000 0x1000>;
+			};
+
 			misc: syscon@1b000 {
 				compatible = "syscon", "simple-mfd";
 				reg = <0x1b000 0x1000>;
@@ -89,6 +98,15 @@
 				#size-cells = <1>;
 				ranges = <0x0 0x1b000 0x1000>;
 			};
+
+			scpu_wrapper: syscon@1d000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1d000 0x2000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1d000 0x2000>;
+			};
 		};
 
 		gic: interrupt-controller@ff011000 {
Signature · 1 line
2.16.4
maintainer Acked-by on v1 11/14
#21 lore raw

RE: [PATCH 11/14] arm64: dts: realtek: rtd129x: Add SB2 and SCPU Wrapper syscon nodes

Quoted 46 lines

Add syscon mfd nodes for SB2 and SCPU Wrapper to RTD129x DT.

---
 arch/arm64/boot/dts/realtek/rtd129x.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
arch/arm64/boot/dts/realtek/rtd129x.dtsi +18 -1
index 34dc09790d0b..39aefe66a794 100644
@@ -81,6 +81,15 @@
 				ranges = <0x0 0x7000 0x1000>;
 			};
 
+			sb2: syscon@1a000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1a000 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1a000 0x1000>;
+			};
+
 			misc: syscon@1b000 {
 				compatible = "syscon", "simple-mfd";
 				reg = <0x1b000 0x1000>;
@@ -89,6 +98,15 @@
 				#size-cells = <1>;
 				ranges = <0x0 0x1b000 0x1000>;
 			};
+
+			scpu_wrapper: syscon@1d000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1d000 0x2000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1d000 0x2000>;
+			};
 		};
 
 		gic: interrupt-controller@ff011000 {
--
Quoted 3 lines

2.16.4

#22 lore raw

PATCH 12/14 arm64: dts: realtek: rtd139x: Add SB2 and SCPU Wrapper syscon nodes

In reply to Andreas Färber

Add syscon mfd nodes for SB2 and SCPU Wrapper to RTD139x DT.

---
 arch/arm64/boot/dts/realtek/rtd139x.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
arch/arm64/boot/dts/realtek/rtd139x.dtsi +18 -0
index 3a571f3b7e38..a3c10ceeb586 100644
@@ -79,6 +79,15 @@
 				ranges = <0x0 0x7000 0x1000>;
 			};
 
+			sb2: syscon@1a000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1a000 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1a000 0x1000>;
+			};
+
 			misc: syscon@1b000 {
 				compatible = "syscon", "simple-mfd";
 				reg = <0x1b000 0x1000>;
@@ -87,6 +96,15 @@
 				#size-cells = <1>;
 				ranges = <0x0 0x1b000 0x1000>;
 			};
+
+			scpu_wrapper: syscon@1d000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1d000 0x2000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1d000 0x2000>;
+			};
 		};
 
 		gic: interrupt-controller@ff011000 {
Signature · 1 line
2.16.4
maintainer Acked-by on v1 12/14
#23 lore raw

RE: [PATCH 12/14] arm64: dts: realtek: rtd139x: Add SB2 and SCPU Wrapper syscon nodes

Quoted 46 lines

Add syscon mfd nodes for SB2 and SCPU Wrapper to RTD139x DT.

---
 arch/arm64/boot/dts/realtek/rtd139x.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
arch/arm64/boot/dts/realtek/rtd139x.dtsi +18 -1
index 3a571f3b7e38..a3c10ceeb586 100644
@@ -79,6 +79,15 @@
 				ranges = <0x0 0x7000 0x1000>;
 			};
 
+			sb2: syscon@1a000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1a000 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1a000 0x1000>;
+			};
+
 			misc: syscon@1b000 {
 				compatible = "syscon", "simple-mfd";
 				reg = <0x1b000 0x1000>;
@@ -87,6 +96,15 @@
 				#size-cells = <1>;
 				ranges = <0x0 0x1b000 0x1000>;
 			};
+
+			scpu_wrapper: syscon@1d000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1d000 0x2000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1d000 0x2000>;
+			};
 		};
 
 		gic: interrupt-controller@ff011000 {
--
Quoted 3 lines

2.16.4

#24 lore raw

PATCH 13/14 arm64: dts: realtek: rtd16xx: Add SB2 and SCPU Wrapper syscon nodes

In reply to Andreas Färber

Add syscon mfd nodes for SB2 and SCPU Wrapper to RTD16xx DT.

---
 arch/arm64/boot/dts/realtek/rtd16xx.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
arch/arm64/boot/dts/realtek/rtd16xx.dtsi +18 -0
index 776efc10bab2..bc88cf749f33 100644
@@ -136,6 +136,15 @@
 				ranges = <0x0 0x7000 0x1000>;
 			};
 
+			sb2: syscon@1a000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1a000 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1a000 0x1000>;
+			};
+
 			misc: syscon@1b000 {
 				compatible = "syscon", "simple-mfd";
 				reg = <0x1b000 0x1000>;
@@ -144,6 +153,15 @@
 				#size-cells = <1>;
 				ranges = <0x0 0x1b000 0x1000>;
 			};
+
+			scpu_wrapper: syscon@1d000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1d000 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1d000 0x1000>;
+			};
 		};
 
 		gic: interrupt-controller@ff100000 {
Signature · 1 line
2.16.4
maintainer Acked-by on v1 13/14
#25 lore raw

RE: [PATCH 13/14] arm64: dts: realtek: rtd16xx: Add SB2 and SCPU Wrapper syscon nodes

Quoted 46 lines

Add syscon mfd nodes for SB2 and SCPU Wrapper to RTD16xx DT.

---
 arch/arm64/boot/dts/realtek/rtd16xx.dtsi | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)
arch/arm64/boot/dts/realtek/rtd16xx.dtsi +18 -1
index 776efc10bab2..bc88cf749f33 100644
@@ -136,6 +136,15 @@
 				ranges = <0x0 0x7000 0x1000>;
 			};
 
+			sb2: syscon@1a000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1a000 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1a000 0x1000>;
+			};
+
 			misc: syscon@1b000 {
 				compatible = "syscon", "simple-mfd";
 				reg = <0x1b000 0x1000>;
@@ -144,6 +153,15 @@
 				#size-cells = <1>;
 				ranges = <0x0 0x1b000 0x1000>;
 			};
+
+			scpu_wrapper: syscon@1d000 {
+				compatible = "syscon", "simple-mfd";
+				reg = <0x1d000 0x1000>;
+				reg-io-width = <4>;
+				#address-cells = <1>;
+				#size-cells = <1>;
+				ranges = <0x0 0x1d000 0x1000>;
+			};
 		};
 
 		gic: interrupt-controller@ff100000 {
--
Quoted 3 lines

2.16.4

#26 lore raw

PATCH 14/14 dt-bindings: reset: rtd1295: Add SB2 reset

In reply to Andreas Färber

Add a constant for reset3 SB2, based on downstream crt_sys_reg.h.

---
 include/dt-bindings/reset/realtek,rtd1295.h | 3 +++
 1 file changed, 3 insertions(+)
include/dt-bindings/reset/realtek,rtd1295.h +3 -0
index 2c0cb6afe816..dd89e4c80264 100644
@@ -75,6 +75,9 @@
 #define RTD1295_RSTN_CBUS_TX		30
 #define RTD1295_RSTN_SDS_PHY		31
 
+/* soft reset 3 */
+#define RTD1295_RSTN_SB2		0
+
 /* soft reset 4 */
 #define RTD1295_RSTN_DCPHY_CRT		0
 #define RTD1295_RSTN_DCPHY_ALERT_RX	1
Signature · 1 line
2.16.4
maintainer Acked-by on v1 14/14
#27 lore raw

Re: [PATCH 14/14] dt-bindings: reset: rtd1295: Add SB2 reset

Quoted 7 lines · On Mon, 2 Dec 2019 19:22:04 +0100, =?UTF-8?q?Andreas=20F=C3=A4rber?= wrote:

Add a constant for reset3 SB2, based on downstream crt_sys_reg.h.

---
 include/dt-bindings/reset/realtek,rtd1295.h | 3 +++
 1 file changed, 3 insertions(+)
maintainer Acked-by on v1 14/14
#28 lore raw

RE: [PATCH 14/14] dt-bindings: reset: rtd1295: Add SB2 reset

In reply to Andreas Färber
Quoted 23 lines

Add a constant for reset3 SB2, based on downstream crt_sys_reg.h.

---
 include/dt-bindings/reset/realtek,rtd1295.h | 3 +++
 1 file changed, 3 insertions(+)
include/dt-bindings/reset/realtek,rtd1295.h +3 -1
index 2c0cb6afe816..dd89e4c80264 100644
@@ -75,6 +75,9 @@
 #define RTD1295_RSTN_CBUS_TX		30
 #define RTD1295_RSTN_SDS_PHY		31
 
+/* soft reset 3 */
+#define RTD1295_RSTN_SB2		0
+
 /* soft reset 4 */
 #define RTD1295_RSTN_DCPHY_CRT		0
 #define RTD1295_RSTN_DCPHY_ALERT_RX	1
--
Quoted 2 lines

2.16.4

_______________________________________________
linux-arm-kernel mailing list
[email protected]
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

#29 lore raw
In reply to Andreas Färber

Hi James,

Am 02.12.19 um 19:21 schrieb Andreas Färber:

Quoted 9 lines

This patch series factors out system controller multi-function device nodes for CRT, Iso, Misc, SB2 and SCPU Wrapper IP blocks.

It was inspired by my SoC info RFC, as discussed in its cover letter [1].

Goal of DT is to describe the hardware, and in previous patches we've already introduced Realtek's r-bus as node layer. The next step here is to model multi-function blocks as nodes. In order to cope with 80-character line limit, child nodes are added via reference rather than in-place.

I'm waiting for your Acked-by of the blocks & numbers in these patches. Other Realtek engineers are also invited to respond, of course.

Thanks in advance,
Andreas

Quoted 24 lines

Andreas Färber (14):
ARM: dts: rtd1195: Introduce iso and misc syscon
arm64: dts: realtek: rtd129x: Introduce CRT, iso and misc syscon
arm64: dts: realtek: rtd139x: Introduce CRT, iso and misc syscon
arm64: dts: realtek: rtd16xx: Introduce iso and misc syscon
ARM: dts: rtd1195: Add CRT syscon node
dt-bindings: reset: Add Realtek RTD1195
ARM: dts: rtd1195: Add reset nodes
ARM: dts: rtd1195: Add UART resets
arm64: dts: realtek: rtd16xx: Add CRT syscon node
ARM: dts: rtd1195: Add SB2 and SCPU Wrapper syscon nodes
arm64: dts: realtek: rtd129x: Add SB2 and SCPU Wrapper syscon nodes
arm64: dts: realtek: rtd139x: Add SB2 and SCPU Wrapper syscon nodes
arm64: dts: realtek: rtd16xx: Add SB2 and SCPU Wrapper syscon nodes
dt-bindings: reset: rtd1295: Add SB2 reset

  arch/arm/boot/dts/rtd1195.dtsi              | 110 ++++++++++++++++---
  arch/arm64/boot/dts/realtek/rtd129x.dtsi    | 157 ++++++++++++++++++----------
  arch/arm64/boot/dts/realtek/rtd139x.dtsi    | 157 ++++++++++++++++++----------
  arch/arm64/boot/dts/realtek/rtd16xx.dtsi    |  91 ++++++++++++----
  include/dt-bindings/reset/realtek,rtd1195.h |  74 +++++++++++++
  include/dt-bindings/reset/realtek,rtd1295.h |   3 +
  6 files changed, 449 insertions(+), 143 deletions(-)

create mode 100644 include/dt-bindings/reset/realtek,rtd1195.h

Signature · 4 lines
SUSE Software Solutions Germany GmbH
Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Felix Imendörffer
HRB 36809 (AG Nürnberg)
#31 lore raw

Hi James,

Am 31.12.19 um 10:47 schrieb James Tai:

Quoted 4 lines
Quoted 2 lines

I'm waiting for your Acked-by of the blocks & numbers in these patches. Other Realtek engineers are also invited to respond, of course.

I have reviewed these patches.

Thanks - does anything need changes in patch 01 or is that ack'ed, too?

Regards,
Andreas

Signature · 4 lines
SUSE Software Solutions Germany GmbH
Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Felix Imendörffer
HRB 36809 (AG Nürnberg)
#32 lore raw

Am 03.01.20 um 03:58 schrieb Andreas Färber:

Quoted 9 lines

Hi James,

Am 31.12.19 um 10:47 schrieb James Tai:

Quoted 4 lines
Quoted 2 lines

I'm waiting for your Acked-by of the blocks & numbers in these patches. Other Realtek engineers are also invited to respond, of course.

I have reviewed these patches.

Thanks - does anything need changes in patch 01 or is that ack'ed, too?

No further response, so all (incl. 01/14) applied to linux-realtek.git:

https://git.kernel.org/pub/scm/linux/kernel/git/afaerber/linux-realtek.git/log/?h=v5.6/dt

Should there be anything wrong with 01/14, just send a follow-up patch.

Regards,
Andreas

Signature · 4 lines
SUSE Software Solutions Germany GmbH
Maxfeldstr. 5, 90409 Nürnberg, Germany
GF: Felix Imendörffer
HRB 36809 (AG Nürnberg)