Problem with 2.4.14 mounting i2o device as root device Adaptec 3200 RAID controller?
It may be an esoteric problem in my config, but I installed a RedHat 7.2 onto an Adaptec (It was strange, I could install one out of 3 tries, but rebooting into the 2.4.7-pre that ships with RedHat it got to unloading free memory, paused about 2 minutes, the the screen rolls with unable to read device messages) 3200s/quantum combination, but it gives me read problems on the device, with anything more than 512 MG RAM. Thought it might be kernel related so tried a freshly rolled 2.4.14 kernel, and it fails to mount the root point /dev/i2o/hda1 (kernel panic, cannot mount 5001)
Hardware has mostly been ruled out, as we replaced the motherboard/and controller as well as the mundane cables and terminators...
Is anyone successfully using 2.4.14 on an Adaptec 3200s controller? This could be a PCI issue, because just we see a lot of interrrupt activity on the card just before it dies..
Am not using modules, compiled the i20 support directly into 2.4.14
Wanted to get some serious 2.4.14 testing on this platform.. so no suggestions about rolling back to 2.2 series.. :)
Signature · 9 lines
"Catch the Magic of Linux..." -------------------------------------------------------- Michael Peddemors - Senior Consultant LinuxAdministration - Internet Services NetworkServices - Programming - Security Wizard IT Services http://www.wizard.ca Linux Support Specialist - http://www.linuxmagic.com -------------------------------------------------------- (604)589-0037 Beautiful British Columbia, Canada
Re: Problem with 2.4.14 mounting i2o device as root device Adaptec 3200
Quoted 3 lines
Is anyone successfully using 2.4.14 on an Adaptec 3200s controller? This could be a PCI issue, because just we see a lot of interrrupt activity on the card just before it dies..
The adaptec i2o has a strange dialect to say the least.
Quoted 1 line
Am not using modules, compiled the i20 support directly into 2.4.14
Build the dpt_i2o scsi driver and use that, thats from Adaptec themselves and speaks their i2o dialect
Quoted 3 lines · In article <1005861234.9918.806.camel@mistress> you wrote:
might be kernel related so tried a freshly rolled 2.4.14 kernel, and it fails to mount the root point
/dev/i2o/hda1(kernel panic, cannot mount 5001)
Try the RH errata 2.4.9 kernel, it is supposed to have support for this device......
On 15 Nov 2001, Michael Peddemors wrote:
I have intel i2o controller but I cannot install (install works but cannot up my mashine after reboot) with RH7.2 but RH7.1 works fine, also RH7.2 has stipied fdisk it see 1 (one) cylinder in my array druid see all but ... installer is stupied with my i2o.... I try use kernel from my working RH 7.1 (2.4.12) with same hardware (i2o intel stl2 mainboard 512MB RAM..) and kernel panic.... stupied installer in RH 7.2 ?
Sorry for my english...
Adam
Quoted 22 lines
It may be an esoteric problem in my config, but I installed a RedHat 7.2 onto an Adaptec (It was strange, I could install one out of 3 tries, but rebooting into the 2.4.7-pre that ships with RedHat it got to unloading free memory, paused about 2 minutes, the the screen rolls with unable to read device messages) 3200s/quantum combination, but it gives me read problems on the device, with anything more than 512 MG RAM. Thought it might be kernel related so tried a freshly rolled 2.4.14 kernel, and it fails to mount the root point
/dev/i2o/hda1(kernel panic, cannot mount 5001)
Hardware has mostly been ruled out, as we replaced the motherboard/and controller as well as the mundane cables and terminators...Is anyone successfully using 2.4.14 on an Adaptec 3200s controller? This could be a PCI issue, because just we see a lot of interrrupt activity on the card just before it dies..
Am not using modules, compiled the i20 support directly into 2.4.14
Wanted to get some serious 2.4.14 testing on this platform.. so no suggestions about rolling back to 2.2 series.. :)