latest au1000 updates
James,
I pushed the latest au1000 code. I had to add a new vec0 handler for the au1000 in head.S, much like the other vec0 ones. I also checked in the vr41xx patch. Jun indicated that he and/or Ralf reworked some of the 41xx so the 41xx will probably have to be updated again, but at least the kernel compiles.
To compile the code right at this moment, you need to make this local change in kernel/Makefile:
[ppopov@zeus linux-dev]$ diff ../stock/kernel/Makefile kernel/Makefile 14c14
< obj-y = sched.o dma.o fork.o exec_domain.o panic.o printk.o \
---
Quoted 1 line
obj-y = sched.o fork.o exec_domain.o panic.o printk.o \
17a18,21
Quoted 4 lines
ifndef
CONFIG_MIPS_AU1000
obj-y += dma.o
endif
and, this local change in drivers/net/Space.c:
diff ../stock/drivers/net/Space.c drivers/net/Space.c 103a104,105
Quoted 2 lines
extern int
gt96100_probe(struct net_device *);
extern intau1000_probe(struct net_device *dev);
382a385,390
Quoted 6 lines
#endif
#ifdef CONFIG_MIPS_GT96100ETH {gt96100_probe, 0}, #endif #ifdef CONFIG_MIPS_AU1000_ENET {au1000_probe, 0},
The Space.c patch really needs to go to Alan. I'll see if he'll take it. The kernel/Makefile patch probably needs to be reworked so that we don't have to touch kernel/Makefile.
I tested the kernel and it seems to work fine, so I think I got everything. However, I haven't tested the fb driver, pcmcia, usb, etc, etc with this kernel. Also, note that if anyone needs usb on this board or any other au1000 board, we'll need to send a local usb patch for non-pci devices. Steve already had most of his work accepted in the usb tree, but the non-pci patch wasn't accepted because the usb code is going through some reorg right now. So, without this usb patch which is only in the MontaVista tree at the moment, usb is not usable on this board.
There are Au1000 customers showing up all over the place, so having the latest code in sourceforge is a good thing. Now I have to find the time to create a patch against the oss tree...
Pete
usb-problems with Au1000
Hello,
I have following configuration:
- mips-Au1000-processor (PB1000-board from Alchemy-Semiconductor)
- _no_ USB-devices connected
- linux from the Montavista-Tree (downloaded in December from
www.alchemysemi.com)(Kernel "2.4.2_hhl20")
- prebuilt crosscompiler from Montavista (downloaded in December from www.alchemysemi.com)
During booting the kernel initalizes the usb-device-driver and a little later prints "USB device not accepting new address...":
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
usb.c: registered new driver usbdevfsusb.c: registered new driver hubusb-ohci.c: USB OHCI at membase 0xb0100000, IRQ 26 usb-ohci.c: usb-builtin, non-PCI OHCIusb.c: new USB bus registered, assigned bus number 1
Product: USB OHCI Root Hub
SerialNumber: b0100000hub.c: USB hub foundhub.c: 2 ports detectedusb-ohci.c: v5.2 Roman Weissgaerber <[email protected]>, David Brownell usb-ohci.c: USB OHCI Host Controller Driverusb.c: registered new driver hid
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 4096) Sending BOOTP requests.... OK
IP-Config: Got BOOTP answer from 192.168.65.17, my address is 192.168.65.240
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Serial driver version 1.01 (2001-02-08) with no serial options enabled ttyS00 at 0xb1100000 (irq = 0) is a 16550
ttyS01 at 0xb1200000 (irq = 1) is a 16550
ttyS02 at 0xb1300000 (irq = 2) is a 16550
ttyS03 at 0xb1400000 (irq = 3) is a 16550
Looking up port of RPC 100003/2 on 192.168.65.17
Looking up port of RPC 100005/2 on 192.168.65.17hub.c: USB new device connect on bus1/1, assigned device number 2 usb.c: USB device not accepting new address=2 (error=-145) <---------????
VFS: Mounted root (nfs filesystem) readonly.
Freeing unused kernel memory: 64k freed
Algorithmics/MIPS FPU Emulator v1.5ahub.c: USB new device connect on bus1/1, assigned device number 3 usb.c: USB device not accepting new address=3 (error=-145) <---------????
<<<<
I wonder what I could have done wrong. The switches on the board are set accordingly the Montavista-faq.txt. I could verify these settings
with the schematics of the board.
After booting, when I plug in an USB-device, the same error messages are repeated.
As far as I know USB should work with this kernel. So maybe this is a hardware failure ? I reduced the CPU-frequency from 396MHz to 120MHz,
but this didn't help, too. The same messages appear, when I plug the device
in the other USB-connector on the board. It's no problem with the power, because I could verify that there are 5Volt on the USB-connector.
Probably someone already knows the solution, because this is not a special
configuration.
Thanks in advance
Signature · 1 line
Wolfgang
Re: usb-problems with Au1000
Quoted 7 lines · Wolfgang Heidrich
Hello,
I have following configuration:
- mips-Au1000-processor (PB1000-board from Alchemy-Semiconductor)
- _no_ USB-devices connected
- linux from the Montavista-Tree (downloaded in December from
Quoted 6 lines
www.alchemysemi.com)(Kernel "2.4.2_hhl20")- prebuilt crosscompiler from Montavista (downloaded in December from www.alchemysemi.com)
During booting the kernel initalizes the usb-device-driver and a little later prints "USB device not accepting new address...":
Which LSP version do you have? Do an "rpm -qa | grep hhl- | grep lsp".
There was a hardware errata in the usb controller, but a software fix is already in the kernel (assuming you have a late enough kernel). Also, the usb switches, S4, should be set to:
1-4 off
5-6 on
7-8 off
Pete
Quoted 63 lines
Quoted 1 line
Quoted 1 line
Quoted 1 line
Quoted 1 line
usb.c: registered new driver usbdevfsusb.c: registered new driver hubusb-ohci.c: USB OHCI at membase0xb0100000, IRQ 26usb-ohci.c: usb-builtin, non-PCI OHCIusb.c: new USB bus registered, assigned bus number 1
Product: USB OHCI Root Hub
SerialNumber:b0100000hub.c: USB hub foundhub.c: 2 ports detectedusb-ohci.c: v5.2 Roman Weissgaerber <[email protected]>, David Brownellusb-ohci.c: USB OHCI Host Controller Driverusb.c: registered new driver hid
mice: PS/2 mouse device common for all mice
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 4096) Sending BOOTP requests.... OK
IP-Config: Got BOOTP answer from 192.168.65.17, my address is 192.168.65.240
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Serial driver version 1.01 (2001-02-08) with no serial options enabled ttyS00 at0xb1100000(irq = 0) is a 16550
ttyS01 at0xb1200000(irq = 1) is a 16550
ttyS02 at0xb1300000(irq = 2) is a 16550
ttyS03 at0xb1400000(irq = 3) is a 16550
Looking up port of RPC 100003/2 on 192.168.65.17
Looking up port of RPC 100005/2 on 192.168.65.17hub.c: USB new device connect on bus1/1, assigned device number 2usb.c: USB device not accepting new address=2 (error=-145) <---------????
VFS: Mounted root (nfs filesystem) readonly.
Freeing unused kernel memory: 64k freed
Algorithmics/MIPS FPU Emulator v1.5ahub.c: USB new device connect on bus1/1, assigned device number 3usb.c: USB device not accepting new address=3 (error=-145) <---------????
<<<<I wonder what I could have done wrong. The switches on the board are set accordingly the Montavista-faq.txt. I could verify these settings
with the schematics of the board.
After booting, when I plug in an USB-device, the same error messages are repeated.As far as I know USB should work with this kernel. So maybe this is a hardware failure ? I reduced the CPU-frequency from 396MHz to 120MHz,
but this didn't help, too. The same messages appear, when I plug the device
in the other USB-connector on the board. It's no problem with the power, because I could verify that there are 5Volt on the USB-connector.Probably someone already knows the solution, because this is not a special
configuration.Thanks in advance
Signature · 1 line
Wolfgang
Re: usb-problems with Au1000
Hello Pete,
Quoted 9 lines · Pete Popov
Quoted 5 lines · Wolfgang Heidrich
Hello,
During booting the kernel initalizes the usb-device-driver and a little later prints "USB device not accepting new address...":
Which LSP version do you have? Do an "rpm -qa | grep hhl- | grep lsp".
hhl-cross-mips_fp_le-lsp-mips-malta-2.4.2_hhl20-hhl2.0.2 hhl-cross-mips_fp_le-lsp-alchemy-pb1000-2.4.2_hhl20-hhl2.0.2
Quoted 8 lines
There was a hardware errata in the usb controller, but a software fix is already in the kernel (assuming you have a late enough kernel). Also, the usb switches, S4, should be set to:
1-4 off
5-6 on
7-8 off
I used these settings. But as far as I know these settings are only relevant for the second USB.
Thanks in advance
Signature · 1 line
Wolfgang
Re: usb-problems with Au1000
Quoted 8 lines · Wolfgang Heidrich
Hello Pete,
Quoted 4 lines · Pete Popov
Quoted 2 lines · Wolfgang Heidrich
Hello,
Quoted 7 lines
Quoted 4 lines
Quoted 2 lines
During booting the kernel initalizes the usb-device-driver and a little later prints "USB device not accepting new address...":
Which LSP version do you have? Do an "rpm -qa | grep hhl- | grep lsp".
hhl-cross-mips_fp_le-lsp-mips-malta-2.4.2_hhl20-hhl2.0.2 hhl-cross-mips_fp_le-lsp-alchemy-pb1000-2.4.2_hhl20-hhl2.0.2
That LSP is old. Get the _hhl20_hhl2.0.3 release. Alchemy should have it on their ftp site by now. Let me know if you still have problems with 2.0.3.
Pete
Quoted 14 lines
Quoted 7 lines
There was a hardware errata in the usb controller, but a software fix is already in the kernel (assuming you have a late enough kernel). Also, the usb switches, S4, should be set to:
1-4 off
5-6 on
7-8 offI used these settings. But as far as I know these settings are only relevant for the second USB.
Thanks in advance
Signature · 1 line
Wolfgang
Re: usb-problems with Au1000
In reply to Wolfgang HeidrichHi,
I'm trying SGI version of kernel-2.2.17.
And I get same message,
At Thu, 10 Jan 2002 18:40:24 +0100,
Quoted 2 lines · Wolfgang Heidrich
hub.c: USB new device connect on bus1/1, assigned device number 3usb.c: USB device not accepting new address=3 (error=-145)
when connect some device.
I checked in some cases:
- Some devices are recognized, some are not.
A joystick device (sanwa supply) works fine.
A mouse device (century corp.) works too.
But another mouse (Logitech Mini Wheel Mouse) doesn't work and
I got message like above.
- When connected via USB hub device, Logitech mouse works fine.
I think USB root HUB doesn't work properly.
By the way:
today, I got a errata document from the chip dealer. This document reports some USB errata.
I read the report and source code, then I found a bug in arch/mips/au1000/pb1000/setup.c.
The errata report says workaround method:
- set the CPU clock is 384MHz
- set the source of USB host controller is CPU clcck.
And the code:
/*
* Setup 48MHz FREQ2 from CPUPLL for USB Host
*/
/* FRDIV2=3 -> div by 8 of 384MHz -> 48MHz */
sys_freqctrl |= ((3<<22) | (1<<21) | (0<<20));
outl(sys_freqctrl, FQ_CNTRL_1);Comment says "Setup FREQ2" but the code set FREQ5.
outl(sys_freqctrl, FQ_CNTRL_1);
should be
outl(sys_freqctrl, FQ_CNTRL_0);
Also formar line:
sys_freqctrl = inl(FQ_CNTRL_1);
should be
sys_freqctrl = inl(FQ_CNTRL_0);
Thanks.
_._. __._ _ . ... _ .___ ._. _____ _... ._ _._ _.._. .____ _ . ... _
Kunihiko IMAI
Re: usb-problems with Au1000
Quoted 10 lines · Kunihiko IMAI
Hi,
I'm trying SGI version of kernel-2.2.17.
And I get same message,At Thu, 10 Jan 2002 18:40:24 +0100,
Quoted 2 lines · Wolfgang Heidrich
hub.c: USB new device connect on bus1/1, assigned device number 3usb.c: USB device not accepting new address=3 (error=-145)
I'm surprised the sgi kernel works with usb at all. We did a patch for non-pci usb devices which was not accepted by the usb project at that time because they were working on a different solution.
Quoted 29 lines
when connect some device.
I checked in some cases:
- Some devices are recognized, some are not.
A joystick device (sanwa supply) works fine.
A mouse device (century corp.) works too.
But another mouse (Logitech Mini Wheel Mouse) doesn't work and
I got message like above.- When connected via USB hub device, Logitech mouse works fine.
I think USB root HUB doesn't work properly.
By the way:
today, I got a errata document from the chip dealer. This document reports some USB errata.
I read the report and source code, then I found a bug inarch/mips/au1000/pb1000/setup.c.The errata report says workaround method:
- set the CPU clock is 384MHz
- set the source of USB host controller is CPU clcck.And the code:
Quoted 8 lines
/* * Setup 48MHz FREQ2 from CPUPLL for USB Host */ /* FRDIV2=3 -> div by 8 of 384MHz -> 48MHz */ sys_freqctrl |= ((3<<22) | (1<<21) | (0<<20)); outl(sys_freqctrl, FQ_CNTRL_1);Comment says "Setup FREQ2" but the code set FREQ5.
It's the comment that's wrong, not the code. The code works and has been tested. Alchemy makes available the Linux Support Package (LSP) which we did. That kernel has been tested with all peripherals so I would recommend that you get that from them. Also,make sure your jumpers are setup correctly (S4).
I do have a better USB workaround which checks the CPU silicon rev, but I haven't had time to send Ralf an updated patch. The current setup.c should work though. Get the latest LSP from Alchemy, check the S4 jumpers (1-4 off, 5-6 on, 7-8 off), and let me know if it still doesn't work for you.
Pete
Re: usb-problems with Au1000
Hi,
At 17 Jan 2002 11:02:03 -0800,
Quoted 10 lines · Pete Popov
Quoted 8 lines · Kunihiko IMAI
Hi,
I'm trying SGI version of kernel-2.2.17.
And I get same message,At Thu, 10 Jan 2002 18:40:24 +0100,
Wolfgang Heidrich wrote:
Quoted 6 lines
Quoted 2 lines
Quoted 2 lines
hub.c: USB new device connect on bus1/1, assigned device number 3usb.c: USB device not accepting new address=3 (error=-145)I'm surprised the sgi kernel works with usb at all. We did a patch for non-pci usb devices which was not accepted by the usb project at that time because they were working on a different solution.
Of course, I patched usb-ohci code with memory mapped I/O support. It is very ugly code, so Linux USB stuff will not accept, I think.
About two years ago, I ported USB OHCI to StrongARM SA1111 CPU and SA1111 companion chip. At that time, I suggested to the author of usb-ohci.c that it should be better to support of memory mapped I/O device, but it was not accepted. On StrongARM, it has DMA memory coherency problem, too. (Au1000 has bus snoop function, so this is not a problem.)
Quoted 13 lines
Quoted 13 lines
The errata report says workaround method:
- set the CPU clock is 384MHz
- set the source of USB host controller is CPU clcck.And the code:
/* * Setup 48MHz FREQ2 from CPUPLL for USB Host */ /* FRDIV2=3 -> div by 8 of 384MHz -> 48MHz */ sys_freqctrl |= ((3<<22) | (1<<21) | (0<<20)); outl(sys_freqctrl, FQ_CNTRL_1);
Quoted 7 lines
Quoted 1 line
Comment says "Setup FREQ2" but the code set FREQ5.
It's the comment that's wrong, not the code. The code works and has been tested. Alchemy makes available the Linux Support Package (LSP) which we did. That kernel has been tested with all peripherals so I would recommend that you get that from them. Also,make sure your jumpers are setup correctly (S4).
In the source code:
sys_clksrc |= ((4<<12) | (0<<11) | (0<<10)); (snip...) outl(sys_clksrc, CLOCK_SOURCE_CNTRL);
This code sets the clock source of USB host controller is FREQ2. So FREQ5 clock source doesn't affect to USB host controller.
And I found HHL version of kernel source code in Pb1000 CD-ROM. I'll read it.
Quoted 5 lines
I do have a better USB workaround which checks the CPU silicon rev, but I haven't had time to send Ralf an updated patch. The current
setup.cshould work though. Get the latest LSP from Alchemy, check the S4 jumpers (1-4 off, 5-6 on, 7-8 off), and let me know if it still doesn't work for you.
OK. I checked S4 DIP SW, it was setted same config.
# Pb1000 documentation doesn't clearly explain at this configration. # So I looked schematics of Pb1000.
This switch affects only J24 connector setting. J2 connector is not affected by S4.
Thanks.
_._. __._ _ . ... _ .___ ._. _____ _... ._ _._ _.._. .____ _ . ... _
Kunihiko IMAI
Re: usb-problems with Au1000
Quoted 3 lines
Of course, I patched usb-ohci code with memory mapped I/O support. It is very ugly code, so Linux USB stuff will not accept, I think.
I think the work we did was clean, but it wasn't accepted anyway. Although, Steve L.'s initial work on mips usb did get accepted and that gave us usb on the it8172 system controller.
Quoted 30 lines
About two years ago, I ported USB OHCI to StrongARM SA1111 CPU and SA1111 companion chip. At that time, I suggested to the author of
usb-ohci.cthat it should be better to support of memory mapped I/O device, but it was not accepted. On StrongARM, it has DMA memory coherency problem, too. (Au1000 has bus snoop function, so this is not a problem.)Quoted 13 lines
Quoted 13 lines
The errata report says workaround method:
- set the CPU clock is 384MHz
- set the source of USB host controller is CPU clcck.And the code:
/* * Setup 48MHz FREQ2 from CPUPLL for USB Host */ /* FRDIV2=3 -> div by 8 of 384MHz -> 48MHz */ sys_freqctrl |= ((3<<22) | (1<<21) | (0<<20)); outl(sys_freqctrl, FQ_CNTRL_1);Quoted 7 lines
Quoted 1 line
Comment says "Setup FREQ2" but the code set FREQ5.
It's the comment that's wrong, not the code. The code works and has been tested. Alchemy makes available the Linux Support Package (LSP) which we did. That kernel has been tested with all peripherals so I would recommend that you get that from them. Also,make sure your jumpers are setup correctly (S4).
In the source code:
Quoted 8 lines
sys_clksrc |= ((4<<12) | (0<<11) | (0<<10)); (snip...) outl(sys_clksrc, CLOCK_SOURCE_CNTRL);This code sets the clock source of USB host controller is FREQ2. So FREQ5 clock source doesn't affect to USB host controller.
I'll take a look at it, thanks.
Quoted 2 lines
And I found HHL version of kernel source code in Pb1000 CD-ROM. I'll read it.
I don't think you have the latest CDROM. That one you have probably has an older version of the LSP.
Quoted 7 lines
Quoted 6 lines
I do have a better USB workaround which checks the CPU silicon rev, but I haven't had time to send Ralf an updated patch. The current
setup.cshould work though. Get the latest LSP from Alchemy, check the S4 jumpers (1-4 off, 5-6 on, 7-8 off), and let me know if it still doesn't work for you.
Quoted 6 lines
OK. I checked S4 DIP SW, it was setted same config.
# Pb1000 documentation doesn't clearly explain at this configration. # So I looked schematics of Pb1000.This switch affects only J24 connector setting. J2 connector is not affected by S4.
The CDROM you have is most definitely old and might not have the latest usb code. Try the latest LSP from Alchemy. The rpms should have "hhl2.0.3" or later in the string.
Pete
Re: usb-problems with Au1000
In reply to Kunihiko IMAIQuoted 9 lines
Quoted 6 lines
It's the comment that's wrong, not the code. The code works and has been tested. Alchemy makes available the Linux Support Package (LSP) which we did. That kernel has been tested with all peripherals so I would recommend that you get that from them. Also,make sure your jumpers are setup correctly (S4).
In the source code:
Quoted 8 lines
sys_clksrc |= ((4<<12) | (0<<11) | (0<<10)); (snip...) outl(sys_clksrc, CLOCK_SOURCE_CNTRL);This code sets the clock source of USB host controller is FREQ2. So FREQ5 clock source doesn't affect to USB host controller.
After looking into it, both the comment and code are correct. From include/asm-mips/au1000.h:
#define FQ_CNTRL_1 0xB1900020
#define FQ_CNTRL_2 0xB1900024
So FQ_CNTRL_1 corresponds to what is now sys_freqctrl0. In other words, the update to the databook has not been incorporated into the Au1000 files. The names of the registers were updated after I had done all the core work. I need to update the code so the names of the registers correspond to the latest Au1000 manual.
Since the boards we have do work with USB and there were some usb hardware glitches, please check with Alchemy on what the problem might be with your board.
Pete
Re: usb-problems with Au1000
Hi,
At 18 Jan 2002 11:49:09 -0800,
Quoted 22 lines · Pete Popov
Quoted 10 lines
Quoted 7 lines
It's the comment that's wrong, not the code. The code works and has been tested. Alchemy makes available the Linux Support Package (LSP) which we did. That kernel has been tested with all peripherals so I would recommend that you get that from them. Also,make sure your jumpers are setup correctly (S4).
In the source code:
Quoted 8 lines
sys_clksrc |= ((4<<12) | (0<<11) | (0<<10)); (snip...) outl(sys_clksrc, CLOCK_SOURCE_CNTRL);This code sets the clock source of USB host controller is FREQ2. So FREQ5 clock source doesn't affect to USB host controller.
After looking into it, both the comment and code are correct. From
include/asm-mips/au1000.h:
Quoted 8 lines
#define
FQ_CNTRL_10xB1900020
#defineFQ_CNTRL_20xB1900024So
FQ_CNTRL_1corresponds to what is nowsys_freqctrl0. In other words, the update to the databook has not been incorporated into the Au1000 files. The names of the registers were updated after I had done all the core work. I need to update the code so the names of the registers correspond to the latest Au1000 manual.
Oh, I see. I'm sorry for my misunderstanding.
Now the relations are like this:
Au1000 manual Linux Header
-----------------------------------sys_freqctl0 FQ_CNTRL_1sys_freqctl1 FQ_CNTRL_2
-----------------------------------
Then it's correct setup.
Thanks.
_._. __._ _ . ... _ .___ ._. _____ _... ._ _._ _.._. .____ _ . ... _
Kunihiko IMAI
Re: usb-problems with Au1000
(I just repeat my last message with corrected subject)
Hi Bob,
Quoted 4 lines
Hi Wolfgang,
Have you been successful in getting the latest files? Thanks,
Bob
Yes, thank you very much, now I really have Beta6 and Beta5. But USB still doesn't work, I still get the message "usb.c: USB device not accepting new address=3 (error=-145)" everytime I plug in a USB device in J2. The same happens with J24.
Only one thing changed (look my Email in the newsgroup from January 10):
With Beta4-Version I always was getting the message
Quoted 1 line
Quoted 1 line
Quoted 1 line
hub.c: USB new device connect on bus1/1, assigned device number 3 usb.c: USB device not accepting new address=3 (error=-145) <<<
already during booting of the kernel, although there were no USB devices connected.
But with Beta6-Version I just get it when plugging in a device after booting:
Quoted 1 line
Quoted 1 line
Quoted 1 line
usb.c: USB device not accepting new address=2 (error=-145) usb.c: USB device not accepting new address=3 (error=-145) <<<
The version of the LSP is now hhl-cross-mips_fp_le-lsp-alchemy-pb1000-2.4.2_hhl20-mb011105.2
The Pb1000 Board Serial Number is 5070.
Maybe you can tell me that the reason is just a buggy Au1000, and perhaps USB is going to work, when we get our own Au1000-boards with newer versions of the Au1000.
Thanks in advance
Signature · 1 line
Wolfgang
Re: usb-problems with Au1000
In reply to Kunihiko IMAIQuoted 29 lines · Kunihiko IMAI
Hi,
At 18 Jan 2002 11:49:09 -0800,
Quoted 25 lines · Pete Popov
Quoted 10 lines
Quoted 7 lines
It's the comment that's wrong, not the code. The code works and has been tested. Alchemy makes available the Linux Support Package (LSP) which we did. That kernel has been tested with all peripherals so I would recommend that you get that from them. Also,make sure your jumpers are setup correctly (S4).
In the source code:
Quoted 8 lines
sys_clksrc |= ((4<<12) | (0<<11) | (0<<10)); (snip...) outl(sys_clksrc, CLOCK_SOURCE_CNTRL);This code sets the clock source of USB host controller is FREQ2. So FREQ5 clock source doesn't affect to USB host controller.
After looking into it, both the comment and code are correct. From
include/asm-mips/au1000.h:#define
FQ_CNTRL_10xB1900020
#defineFQ_CNTRL_20xB1900024
Quoted 7 lines
Quoted 5 lines
So
FQ_CNTRL_1corresponds to what is nowsys_freqctrl0. In other words, the update to the databook has not been incorporated into the Au1000 files. The names of the registers were updated after I had done all the core work. I need to update the code so the names of the registers correspond to the latest Au1000 manual.Oh, I see. I'm sorry for my misunderstanding.
It's OK, one of these days I'll have time to rename all the registers to match the last data book.
Pete
Quoted 7 lines
Now the relations are like this:
Au1000 manual Linux Header
-----------------------------------sys_freqctl0FQ_CNTRL_1sys_freqctl1FQ_CNTRL_2
-----------------------------------