Skip to contentSkip to conversation

: 2.4.18-rc1 - Unable to mount CD-ROM/RW

PROBLEM Shawn Starr 2 participants 2 messages Feb 21, 2002

lore
Share & tools
lore
#0 lore raw

Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX3: IDE controller on PCI bus 00 dev 39
PIIX3: chipset revision 0
PIIX3: not 100% native mode: will probe irqs later

    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:pio, hdd:pio

hda: FUJITSU MPE3064AT, ATA DISK drive
hdb: WDC AC32500H, ATA DISK drive
hdc: YAMAHA CRW2100E, ATAPI CD/DVD-ROM drive <--------------------
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: 12672450 sectors (6488 MB) w/512KiB Cache, CHS=788/255/63, (U)DMA
hdb: Disabling (U)DMA for WDC AC32500H
hdb: 4999680 sectors (2560 MB) w/128KiB Cache, CHS=620/128/63 Partition check:
hda: hda1 hda2
hdb: hdb1
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
3c59x: Donald Becker and others. www.scyld.com/network/vortex.html 00:0c.0: 3Com PCI 3c900 Cyclone 10Mbps TPO at 0xe880. Vers LK1.1.16 PPP generic driver version 2.4.1
PPP Deflate Compression module registered
PPP BSD Compression module registered
SCSI subsystem driver Revision: 1.00
scsi0 : Adaptec AIC7XXX EISA/VLB/PCI SCSI HBA DRIVER, Rev 6.2.4

        <Adaptec 2902/04/10/15/20/30C SCSI adapter>
        aic7850: Single Channel A, SCSI Id=7, 3/253 SCBs

Vendor: HP Model: T4000s Rev: 1.10
Type: Sequential-Access ANSI SCSI revision: 02
scsi1 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: YAMAHA Model: CRW2100E Rev: 1.0N <----------------
Type: CD-ROM ANSI SCSI revision: 02
st: Version 20020205, bufsize 32768, wrt 30720, max init. bufs 4, s/g segs 16
Attached scsi tape st0 at scsi0, channel 0, id 4, lun 0

When i attempt to mount /dev/cdrom (symlink to /dev/scd0) I get

mount: /dev/cdrom is not a valid block device (or /dev/scd0).

What broke? :-(

Shawn.

#1 lore raw

On 21 Feb 2002 12:40:35 -0500
Shawn Starr <[email protected]> wrote:
<snip>

Quoted 6 lines

When i attempt to mount /dev/cdrom (symlink to /dev/scd0) I get

mount: /dev/cdrom is not a valid block device (or /dev/scd0).

What broke? :-(

I got this problem also. Similar config, ATAPI Plextor CDRW using ide-scsi. The system would refuse to read/mount CDs unless I did it as root. (eg, cds wouldn't mount, cdparanoia wouldn't work) Upgrading to -rc2-ac1 seems to have "fixed" it, have you tried -rc2? (I should try to figure out why after class, when I actually have time :3 )
--
Matt