Skip to contentSkip to conversation

Installation issue on 800/F10.

parisc-linux Eric Boniface 5 participants 8 messages Aug 12, 2002 – Aug 13, 2002

lore
Share & tools
lore
#0 lore raw

Hi all,
well I try to install the latest Debian on my (very ? ) old HP9000 800/F10, but I have the following message :

"Branching to kernel entry point 0x00100000. If this is the last message you see, you may need to switch your console. This is a common symptom -- search the FAQ and mailing list at parisc-linux.org"

I am ok to switch whatever it wants, but I don't really see what I can switch.
For your information, I use a Wyse screen (a vt220 I think) plugged to the console port on a SCSI/Console/LAN card.

Any idea ?

Thanks in advance !
Rgds,
Eric.

Signature · 2 lines
Eric Boniface - Hewlett Packard / HPS-IT Infrastructure Team Grenoble Tel.(+33) 4 76 14 30 17 / Telnet : 779-3017
E-mail : [email protected] --- Want to know more about Linux on HP PARISC ? Take a look at http://www.parisc-linux.org
#1 lore raw

Well, I have an F20 at home that I could try to load tonight and see if I get the same issue. I'm using an HP Terminal. I'll try it.

derek

Quoted 19 lines · --- Eric Boniface

Hi all,
well I try to install the latest Debian on my (very ? ) old HP9000 800/F10, but I have the following message :

"Branching to kernel entry point 0x00100000. If this is the last message you see, you may need to switch your console. This is a common symptom -- search the FAQ and mailing list at parisc-linux.org"

I am ok to switch whatever it wants, but I don't really see what I can
switch.
For your information, I use a Wyse screen (a vt220 I think) plugged to
the console port on a SCSI/Console/LAN card.

Quoted 22 lines

Any idea ?

Thanks in advance !
Rgds,
Eric.

Signature · 15 lines
Eric Boniface - Hewlett Packard / HPS-IT Infrastructure Team Grenoble

Tel.(+33) 4 76 14 30 17 / Telnet : 779-3017
E-mail : [email protected] 
--- Want to know more about Linux on HP PARISC ? Take a look at
http://www.parisc-linux.org





_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux

__________________________________________________
Do You Yahoo!?
HotJobs - Search Thousands of New Jobs
http://www.hotjobs.com

#2 lore raw
In reply to Eric Boniface
Quoted 2 lines · On Mon, 12 Aug 2002 18:49:32 +0200 Eric Boniface <[email protected]>…

I am ok to switch whatever it wants, but I don't really see what I can switch.

For any information on PARISC-Linux boot sequence, you can get the latest (still under review) PARISC-Linux Boot HowTo here:
http://testpa.esiee.fr/.test/parisc-linux-boot.[html|pdf]
Look at the 'Consoles' section.

Any feedback about errors or precisions would be greatly appreciated.

Thibaut VARENE
The PA/Linux ESIEE Team
http://pateam.esiee.fr/

#3 lore raw

By the way that site also states that the F,G,H,I series are not supported....fwiw.

derek

Quoted 14 lines · --- Thibaut VARENE
Quoted 1 line · On Mon, 12 Aug 2002 18:49:32 +0200 Eric Boniface <[email protected]>…

I am ok to switch whatever it wants, but I don't really see what I

can

Quoted 1 line

switch.

For any information on PARISC-Linux boot sequence, you can get the latest (still under review) PARISC-Linux Boot HowTo here:
http://testpa.esiee.fr/.test/parisc-linux-boot.[html|pdf]
Look at the 'Consoles' section.

Any feedback about errors or precisions would be greatly appreciated.

Quoted 7 lines

Thibaut VARENE
The PA/Linux ESIEE Team
http://pateam.esiee.fr/
_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux

__________________________________________________
Do You Yahoo!?
HotJobs - Search Thousands of New Jobs
http://www.hotjobs.com

#4 lore raw

That is true to a point. There has been a some work done on the nova class systems mainly by Christoph Platner to get the E series working, and I belive Christoph does have a root nfs E55 running. The problem with the nova class systems are that documentation is sparse and very hard to obtain.

First thing you need to do is configure a kernel with the PDC console support. the nova class systems do not have a hardware console solution (The K-class systems have this same problem). You could also try to enable the EARLY_BOOTUP_DEBUG in arch/parisc/kernel/pdc_cons.c to see if that helps.

Good luck!

- Ryan

Quoted 38 lines · Derek Engelhaupt

By the way that site also states that the F,G,H,I series are not supported....fwiw.

derek

Quoted 14 lines · --- Thibaut VARENE
Quoted 1 line · On Mon, 12 Aug 2002 18:49:32 +0200 Eric Boniface <[email protected]>…

I am ok to switch whatever it wants, but I don't really see what I

can

Quoted 1 line

switch.

For any information on PARISC-Linux boot sequence, you can get the latest (still under review) PARISC-Linux Boot HowTo here:
http://testpa.esiee.fr/.test/parisc-linux-boot.[html|pdf]
Look at the 'Consoles' section.

Any feedback about errors or precisions would be greatly appreciated.

Quoted 7 lines

Thibaut VARENE
The PA/Linux ESIEE Team
http://pateam.esiee.fr/
_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux

__________________________________________________
Do You Yahoo!?
HotJobs - Search Thousands of New Jobs
http://www.hotjobs.com
_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux

#5 lore raw
In reply to Eric Boniface

Hello !

You are in similar position than I, the machines are not supported for now.

BUT, perhaps I can help you to go some further steps. The machines have a proprietary bus system and also proprietary interface chips.

To get my E55 running, I wrote a device driver using the ROM console (used for the boot monitor) as system console under Linux.

Rebuild the linux kernel with CONFIG_PDC_CONSOLE enabled and follow the help steps for setting up the machine:

1. create "/dev/ttyB0" as character device, major=60,

	minor=0 with
	
	mknod /dev/ttyB0 c 60 0

2. edit /etc/inittab to use ttyB0 instead of ttyS0 or tty1, ... to be able to login

3. add or change to kernel parameter line to use

console=ttyB0

This should work, or let's say, should give process in booting.

One further point: Be patient on this point of kernel output. On some machines or dependent of the kernel version (or whatever), sometimes you have to wait up to half a minute here ...

With friendly regards
Christoph

Quoted 30 lines · Eric Boniface

Hi all,
well I try to install the latest Debian on my (very ? ) old HP9000 800/F10, but I have the following message :

"Branching to kernel entry point 0x00100000. If this is the last message you see, you may need to switch your console. This is a common symptom -- search the FAQ and mailing list at parisc-linux.org"

I am ok to switch whatever it wants, but I don't really see what I can switch.
For your information, I use a Wyse screen (a vt220 I think) plugged to the console port on a SCSI/Console/LAN card.

Any idea ?

Thanks in advance !
Rgds,
Eric.

--
Eric Boniface - Hewlett Packard / HPS-IT Infrastructure Team Grenoble Tel.(+33) 4 76 14 30 17 / Telnet : 779-3017
E-mail : [email protected]
--- Want to know more about Linux on HP PARISC ? Take a look at http://www.parisc-linux.org

_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux

Signature · 3 lines
-------------------------------------------------------
private:	[email protected]
company:	[email protected]
#6 lore raw
Quoted 3 lines · On Tue, 13 Aug 2002 00:17:19 +0200 Christoph Plattner…

Rebuild the linux kernel with CONFIG_PDC_CONSOLE enabled and follow the help steps for setting up the machine:

You can try one of the handy PDC enabled ISO/lifimages available at:
http://pateam.esiee.fr/cd-images/lifimages/
http://pateam.esiee.fr/cd-images/testing/

PDC enabled are tagged -PDC-
the latest one features 2.4.19-pa2 kernel

HTH,

Thibaut VARENE
The PA/Linux ESIEE Team
http://pateam.esiee.fr/

#7 lore raw

Hello,

thanks/merci for your help.
I will check this and I will keep you informed.

Rgds,
Eric.

Quoted 29 lines · Thibaut VARENE
Quoted 4 lines · On Tue, 13 Aug 2002 00:17:19 +0200 Christoph Plattner…

Rebuild the linux kernel with CONFIG_PDC_CONSOLE enabled and follow the help steps for setting up the machine:

You can try one of the handy PDC enabled ISO/lifimages available at:
http://pateam.esiee.fr/cd-images/lifimages/
http://pateam.esiee.fr/cd-images/testing/

PDC enabled are tagged -PDC-
the latest one features 2.4.19-pa2 kernel

HTH,

Thibaut VARENE
The PA/Linux ESIEE Team
http://pateam.esiee.fr/
_______________________________________________
parisc-linux mailing list
[email protected]
http://lists.parisc-linux.org/mailman/listinfo/parisc-linux

Signature · 3 lines
Eric BONIFACE - Hewlett Packard / GBIT-EMEA Infrastructure Team Grenoble
Tel.(+33) 4 76 14 30 17 / Telnet : 779-3017
E-mail : [email protected]