unexpected IO-APIC on Gigabyte GA-7VAX
Hi,
I've got some IO-APIC+ACPI problem.
On 2.4 with acpi usb IO-APIC are setup level and usb works. On 2.5 they are setup edge and usb is dead (and when all input is usb-based...).
This has been previously reported in
http://bugzilla.kernel.org/show_bug.cgi?id=10 which seems to all intents dead.
2.5.59-bk2 dmesg and 2.4 & 2.5 interrupts are provided next.
Is there a way to revert 2.5 to working 2.4 behaviour ?
Regards,
2.4.20-rc2-ac1 monolithic (works)
CPU0
0: 3630 IO-APIC-edge timer 1: 4 IO-APIC-edge keyboard 2: 0 XT-PIC cascade 8: 1 IO-APIC-edge rtc 9: 0 IO-APIC-edge acpi 14: 55 IO-APIC-edge ide0 15: 2881 IO-APIC-edge ide1 18: 44 IO-APIC-level cs46xx, eth0 21: 325 IO-APIC-level usb-uhci, usb-uhci, usb-uhci NMI: 0 LOC: 3580 ERR: 0 MIS: 0
2.5.59-bk2 interrupts (usb dead)
CPU0
0: 33371 IO-APIC-edge timer 2: 0 XT-PIC cascade 8: 1 IO-APIC-edge rtc 9: 0 IO-APIC-level acpi 12: 0 IO-APIC-edge ehci-hcd 14: 47 IO-APIC-edge ide0 15: 3100 IO-APIC-edge ide1 18: 79 IO-APIC-level CS46XX, eth0 NMI: 0 LOC: 33295 ERR: 0 MIS: 0
Linux version 2.5.59-bk2-ehci1231-rous1 (root@rousalka) (gcc version 3.2.1 20030127 (Red Hat Linux 8.0 3.2.1-6)) #1 Sat Feb 8 18:35:18 CET 2003
Video mode to be used for restore is f00
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 00000000000a0000 (usable)
BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000001fff0000 (usable)
BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS)
BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data)
BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
BIOS-e820: 00000000ffff0000 - 0000000100000000 (reserved)
511MB LOWMEM available.
found SMP MP-table at 000f4b80
hm, page 000f4000 reserved twice.
hm, page 000f5000 reserved twice.
hm, page 000f0000 reserved twice.
hm, page 000f1000 reserved twice.
On node 0 totalpages: 131056
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 126960 pages, LIFO batch:16
HighMem zone: 0 pages, LIFO batch:1
ACPI: RSDP (v000 GBT ) @ 0x000f64f0
ACPI: RSDT (v001 GBT AWRDACPI 16944.11825) @ 0x1fff3000
ACPI: FADT (v001 GBT AWRDACPI 16944.11825) @ 0x1fff3040
ACPI: MADT (v001 GBT AWRDACPI 16944.11825) @ 0x1fff6ac0
ACPI: DSDT (v001 GBT AWRDACPI 00000.04096) @ 0x00000000
ACPI: BIOS passes blacklist
ACPI: Local APIC address 0xfee00000
ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled) Processor #0 6:6 APIC version 16
ACPI: LAPIC_NMI (acpi_id[0x00] polarity[0x0] trigger[0x0] lint[0x1])
ACPI: IOAPIC (id[0x02] address[0xfec00000] global_irq_base[0x0]) IOAPIC[0]: Assigned apic_id 2
IOAPIC[0]: apic_id 2, version 3, address 0xfec00000, IRQ 0-23
ACPI: INT_SRC_OVR (bus[0] irq[0x0] global_irq[0x2] polarity[0x0] trigger[0x0])
ACPI: INT_SRC_OVR (bus[0] irq[0x9] global_irq[0x9] polarity[0x3] trigger[0x3])
Enabling APIC mode: Flat. Using 1 I/O APICs
Using ACPI (MADT) for SMP configuration information Building zonelist for node : 0
Kernel command line: ro root=/dev/hdc1 video=matrox:vesa:0x11B,fh:96,fv:160
Initializing CPU#0
PID hash table entries: 2048 (order 11: 16384 bytes) Detected 1741.247 MHz processor.
Console: colour VGA+ 80x25
Calibrating delay loop... 3432.44 BogoMIPS
Memory: 514816k/524224k available (2240k kernel code, 8664k reserved, 879k data, 136k init, 0k highmem)
Dentry cache hash table entries: 65536 (order: 7, 524288 bytes) Inode-cache hash table entries: 32768 (order: 6, 262144 bytes) Mount-cache hash table entries: 512 (order: 0, 4096 bytes) -> /dev
-> /dev/console
-> /root
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After generic, caps: 0383fbff c1c3fbff 00000000 00000000
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
Machine check exception polling timer started.
CPU: AMD Athlon(tm) XP 2100+ stepping 02
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
enabled ExtINT on CPU#0
ESR value before enabling vector: 00000000
ESR value after enabling vector: 00000000
ENABLING IO-APIC IRQs
init IO_APIC IRQs
IO-APIC (apicid-pin) 2-0, 2-16, 2-17, 2-18, 2-19, 2-20, 2-21, 2-22,
2-23 not connected.
..TIMER: vector=0x31 pin1=2 pin2=0
number of MP IRQ sources: 16.
number of IO-APIC #2 registers: 24.
testing the IO APIC.......................
IO APIC #2......
.... register #00: 02000000
....... : physical APIC id: 02 ....... : Delivery Type: 0 ....... : LTS : 0 .... register #01: 00178003 ....... : max redirection entries: 0017 ....... : PRQ implemented: 1 ....... : IO APIC version: 0003
WARNING: unexpected IO-APIC, please mail
to [email protected]
.... IRQ redirection table:
NR Log Phy Mask Trig IRR Pol Stat Dest Deli Vect:
00 000 00 1 0 0 0 0 0 0 00 01 001 01 0 0 0 0 0 1 1 39 02 001 01 0 0 0 0 0 1 1 31 03 001 01 0 0 0 0 0 1 1 41 04 001 01 0 0 0 0 0 1 1 49 05 001 01 0 0 0 0 0 1 1 51 06 001 01 0 0 0 0 0 1 1 59 07 001 01 0 0 0 0 0 1 1 61 08 001 01 0 0 0 0 0 1 1 69 09 001 01 1 1 0 1 0 1 1 71 0a 001 01 0 0 0 0 0 1 1 79 0b 001 01 0 0 0 0 0 1 1 81 0c 001 01 0 0 0 0 0 1 1 89 0d 001 01 0 0 0 0 0 1 1 91 0e 001 01 0 0 0 0 0 1 1 99 0f 001 01 0 0 0 0 0 1 1 A1 10 000 00 1 0 0 0 0 0 0 00 11 000 00 1 0 0 0 0 0 0 00 12 000 00 1 0 0 0 0 0 0 00 13 000 00 1 0 0 0 0 0 0 00 14 000 00 1 0 0 0 0 0 0 00 15 000 00 1 0 0 0 0 0 0 00 16 000 00 1 0 0 0 0 0 0 00 17 000 00 1 0 0 0 0 0 0 00
IRQ to pin mappings:
IRQ0 -> 0:2
IRQ1 -> 0:1
IRQ3 -> 0:3
IRQ4 -> 0:4
IRQ5 -> 0:5
IRQ6 -> 0:6
IRQ7 -> 0:7
IRQ8 -> 0:8
IRQ9 -> 0:9
IRQ10 -> 0:10
IRQ11 -> 0:11
IRQ12 -> 0:12
IRQ13 -> 0:13
IRQ14 -> 0:14
IRQ15 -> 0:15
.................................... done.
Using local APIC timer interrupts.
calibrating APIC timer ...
..... CPU clock speed is 1741.0226 MHz.
..... host bus clock speed is 267.0880 MHz.
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket
mtrr: v2.0 (20020519)
PCI: Using configuration type 1
BIO: pool of 256 setup, 14Kb (56 bytes/bio)
biovec pool[0]: 1 bvecs: 256 entries (12 bytes)
biovec pool[1]: 4 bvecs: 256 entries (48 bytes)
biovec pool[2]: 16 bvecs: 256 entries (192 bytes)
biovec pool[3]: 64 bvecs: 256 entries (768 bytes)
biovec pool[4]: 128 bvecs: 256 entries (1536 bytes)
biovec pool[5]: 256 bvecs: 256 entries (3072 bytes)
ACPI: Subsystem revision 20030122
ACPI-0262: *** Info: GPE Block0 defined as GPE0 to GPE15
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 *7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 10 11 *12 14 15)
ACPI: PCI Interrupt Link [ALKA] (IRQs 20, disabled)
ACPI: PCI Interrupt Link [ALKB] (IRQs 21, disabled)
ACPI: PCI Interrupt Link [ALKC] (IRQs 22, disabled)
ACPI: PCI Interrupt Link [ALKD] (IRQs 23, disabled)
block request queues:
128 requests per read queue
128 requests per write queue
8 requests per batch
enter congestion at 15
exit congestion at 17
SCSI subsystem driver Revision: 1.00drivers/usb/core/usb.c: registered new driver usbfs drivers/usb/core/usb.c: registered new driver hub
ACPI: PCI Interrupt Link [ALKA] enabled at IRQ 0
ACPI: PCI Interrupt Link [ALKB] enabled at IRQ 0
ACPI: PCI Interrupt Link [ALKC] enabled at IRQ 0
ACPI: PCI Interrupt Link [ALKD] enabled at IRQ 0
IOAPIC[0]: Set PCI routing entry (2-17 -> 0xa9 -> IRQ 17) 00:00:09[A] -> 2-17 -> IRQ 17
IOAPIC[0]: Set PCI routing entry (2-18 -> 0xb1 -> IRQ 18) 00:00:09[B] -> 2-18 -> IRQ 18
IOAPIC[0]: Set PCI routing entry (2-19 -> 0xb9 -> IRQ 19) 00:00:09[C] -> 2-19 -> IRQ 19
IOAPIC[0]: Set PCI routing entry (2-16 -> 0xc1 -> IRQ 16) 00:00:09[D] -> 2-16 -> IRQ 16
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-16 already programmed
Pin 2-17 already programmed
Pin 2-18 already programmed
Pin 2-19 already programmed
ACPI: No IRQ known for interrupt pin A of device 00:10.0<4>ACPI: No IRQ known for interrupt pin B of device 00:10.1<4>ACPI: No IRQ known for interrupt pin C of device 00:10.2<4>ACPI: No IRQ known for interrupt pin D of device 00:10.3<4>ACPI: No IRQ known for interrupt pin A of device 00:11.1 - using IRQ 255
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
IA-32 Microcode Update Driver: v1.11 <[email protected]> Enabling SEP on CPU 0aio_setup: sizeof(struct page) = 40
VFS: Disk quotas dquot_6.5.1
Journalled Block Device driver loaded
udf: registering filesystem
ACPI: Power Button (FF) [PWRF]
ACPI: Processor [CPU0] (supports C1 C2, 2 throttling states)
pty: 256 Unix98 ptys configured
Real Time Clock Driver v1.11
Non-volatile memory driver v1.2
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA KT400 AGP3 chipset
agpgart: Maximum main memory to use for agp memory: 439M
agpgart: unable to determine aperture size.
[drm:drm_init] *ERROR* Cannot initialize the agpgart module. Uninitialised timer!
This is just a warning. Your computer is OK function=0x00000000, data=0x0
Call Trace: [<c01252e1>] check_timer_failed+0x61/0x70 [<c01255ca>] del_timer+0x1a/0x80 [<c0213914>] mga_takedown+0x64/0x3a0 [<c021878f>] mga_stub_unregister+0x2f/0x50 [<c01f23df>] driver_register+0x2f/0x40 [<c01d2037>] pci_register_driver+0x47/0x60 [<c010507a>] init+0x3a/0x160 [<c0105040>] init+0x0/0x160 [<c010713d>] kernel_thread_helper+0x5/0x18
Floppy drive(s): fd0 is 1.44M
FDC 0 is a post-1991 82077
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 Fast Ethernet at 0xe0807000, 00:20:ed:44:99:54, IRQ 18
eth0: Identified 8139 chip type 'RTL-8139C'
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xxVP_IDE: IDE controller at PCI slot 00:11.1
ACPI: No IRQ known for interrupt pin A of device 00:11.1 - using IRQ 255VP_IDE: chipset revision 6VP_IDE: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xxVP_IDE: VIA vt8235 (rev 00) IDE UDMA133 controller on pci00:11.1
ide0: BM-DMA at 0xdc00-0xdc07, BIOS settings: hda:DMA, hdb:DMA
ide1: BM-DMA at 0xdc08-0xdc0f, BIOS settings: hdc:DMA, hdd:DMAhda: IBM-DJNA-371350, ATA DISK drive
hdb: YAMAHA CRW2100E, ATAPI CD/DVD-ROM drive
hda: DMA disabled
hdb: DMA disabled
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: MAXTOR 6L080J4, ATA DISK drive
hdd: TOSHIBA DVD-ROM SD-M1302, ATAPI CD/DVD-ROM drive
hdc: DMA disabled
hdd: DMA disabled
ide1 at 0x170-0x177,0x376 on irq 15
hda: host protected area => 1
hda: 26520480 sectors (13578 MB) w/1966KiB Cache, CHS=26310/16/63
hda: hda1 hda2 < hda5 hda6 >
hdc: host protected area => 1
hdc: 156355584 sectors (80054 MB) w/1819KiB Cache, CHS=155114/16/63, UDMA(133)
hdc: hdc1 hdc2
hdb: ATAPI 40X CD-ROM CD-R/RW drive, 8192kB Cache, UDMA(25) Uniform CD-ROM driver Revision: 3.12end_request: I/O error, dev hdb, sector 0
hdd: ATAPI 40X DVD-ROM drive, 256kB Cache, UDMA(33)end_request: I/O error, dev hdd, sector 0 request_module[scsi_hostadapter]: not ready request_module[scsi_hostadapter]: not ready
ACPI: No IRQ known for interrupt pin D of device 00:10.3<6>ehci-hcd 00:10.3: VIA Technologies, In USB 2.0
ehci-hcd 00:10.3: irq 12, pci mem e0818000
Please use the 'usbfs' filetype instead, the 'usbdevfs' name is deprecated.
ehci-hcd 00:10.3: new USB bus registered, assigned bus number 1
PCI: 00:10.3 PCI cache line size set incorrectly (32 bytes) by BIOS/FW, correcting to 64
ehci-hcd 00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Jan-22 hub 1-0:0: USB hub found
hub 1-0:0: 6 ports detected
Initializing USB Mass Storage driver... drivers/usb/core/usb.c: registered new driver usb-storage USB Mass Storage support registered.drivers/usb/core/usb.c: registered new driver hiddev drivers/usb/core/usb.c: registered new driver hid drivers/usb/input/hid-core.c: v2.0:USB HID core driver
mice: PS/2 mouse device common for all mice
input: PC Speaker
i2c-dev.o: i2c /dev entries driver module version 2.6.4 (20020719) i2c-proc.o version 2.6.4 (20020719)
Advanced Linux Sound Architecture Driver Version 0.9.0rc6 (Tue Jan 28 12:17:23 2003 UTC).
request_module[snd-card-0]: not ready request_module[snd-card-1]: not ready request_module[snd-card-2]: not ready request_module[snd-card-3]: not ready request_module[snd-card-4]: not ready request_module[snd-card-5]: not ready request_module[snd-card-6]: not ready request_module[snd-card-7]: not ready
hub 1-0:0: debounce: port 1: delay 100ms stable 4 status 0x501 ALSA device list:
#0: Sound Fusion CS46xx at 0xe9100000/0xe9000000, irq 18
NET4: Linux TCP/IP 1.0 for NET4.0
IP: routing cache hash table of 4096 buckets, 32Kbytes
TCP: Hash tables configured (established 32768 bind 65536) ip_conntrack version 2.1 (4095 buckets, 32760 max) - 160 bytes per conntrackip_tables: (C) 2000-2002 Netfilter core team
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Freeing unused kernel memory: 136k freed
hub 1-0:0: new USB device on port 1, assigned address 2 Please use the 'usbfs' filetype instead, the 'usbdevfs' name is deprecated.
EXT3 FS 2.4-0.9.16, 02 Dec 2001 on ide1(22,1), internal journal Adding 262072k swap on /dev/hdc2. Priority:-1 extents:1 Adding 265032k swap on /dev/hda6. Priority:-2 extents:1 drivers/usb/core/message.c: usb_control/bulk_msg: timeout
Regards,
Signature · 1 line
Nicolas Mailhot