Skip to contentSkip to conversation

problems with Maestro3 / NEC LM800J/7

DISCUSSION Fernando Pablo Lopez-Lezcano 2 participants 4 messages Mar 29, 2003 – Apr 2, 2003

lore
Share & tools
lore
#0 lore raw

Hi gurus... I'm having problems getting sound out of this laptop:
NEC LM800J/7
I'm using 2.4.20-pre6 + current alsa cvs (post 0.9.2)... After installing everything is fine, drivers load perfectly, I unmute all controls, raise all volumes and aplay seems happy playing a soundfile, except I get no sound (from the speakers or the headphone connection). I tried tweaking all controls in gamix with no success...

Here is the lspci -v -v for the audio controller:

00:04.0 Multimedia audio controller: ESS Technology ES1988 Allegro-1 (rev 12)
Subsystem: NEC Corporation: Unknown device 80f1
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (500ns min, 6000ns max)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 1400 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0-,D1+,D2+,D3hot+,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-

Any suggestions? There must be _one_ pin that is not being turned on :-) Anything I could post that would enable debugging this? Thanks!
-- Fernando

-------------------------------------------------------
This SF.net email is sponsored by:
The Definitive IT and Networking Event. Be There! NetWorld+Interop Las Vegas 2003 -- Register today!
http://ads.sourceforge.net/cgi-bin/redirect.pl?keyn0001en

#1 lore raw
Quoted 7 lines

Hi gurus... I'm having problems getting sound out of this laptop:
NEC LM800J/7
I'm using 2.4.20-pre6 + current alsa cvs (post 0.9.2)... After installing everything is fine, drivers load perfectly, I unmute all controls, raise all volumes and aplay seems happy playing a soundfile, except I get no sound (from the speakers or the headphone connection). I tried tweaking all controls in gamix with no success...

For future reference: I started playing with the module options and got it to work when loading with:

amp_gpio=3

-- Fernando

-------------------------------------------------------
This SF.net email is sponsored by:
The Definitive IT and Networking Event. Be There! NetWorld+Interop Las Vegas 2003 -- Register today!
http://ads.sourceforge.net/cgi-bin/redirect.pl?keyn0001en

#2 lore raw

Hi Fernando,

At 28 Mar 2003 16:58:29 -0800,

Quoted 9 lines · Fernando Pablo Lopez-Lezcano
Quoted 8 lines

Hi gurus... I'm having problems getting sound out of this laptop:
NEC LM800J/7
I'm using 2.4.20-pre6 + current alsa cvs (post 0.9.2)... After installing everything is fine, drivers load perfectly, I unmute all controls, raise all volumes and aplay seems happy playing a soundfile, except I get no sound (from the speakers or the headphone connection). I tried tweaking all controls in gamix with no success...

Quoted 4 lines

For future reference: I started playing with the module options and got it to work when loading with:

amp_gpio=3

great that you already found the solution.

could you give the output of lspci -nv to add this device entry to the quirk list? at the next update, the driver should work without this option.

ciao,

Takashi

-------------------------------------------------------
This SF.net email is sponsored by:
The Definitive IT and Networking Event. Be There! NetWorld+Interop Las Vegas 2003 -- Register today!
http://ads.sourceforge.net/cgi-bin/redirect.pl?keyn0001en

#3 lore raw
Quoted 11 lines
Quoted 11 lines
Quoted 7 lines

Hi gurus... I'm having problems getting sound out of this laptop:
NEC LM800J/7
I'm using 2.4.20-pre6 + current alsa cvs (post 0.9.2)... After installing everything is fine, drivers load perfectly, I unmute all controls, raise all volumes and aplay seems happy playing a soundfile, except I get no sound (from the speakers or the headphone connection). I tried tweaking all controls in gamix with no success...

For future reference: I started playing with the module options and got it to work when loading with:

Quoted 7 lines
Quoted 1 line

amp_gpio=3

great that you already found the solution.

could you give the output of lspci -nv to add this device entry to the quirk list? at the next update, the driver should work without this option.

Sure, it is attached to this email (the owner of the laptop just sent it to me - thanks Rodrigo)...

-- Fernando

00:00.0 Class 0600: 8086:7190 (rev 03)
Flags: bus master, medium devsel, latency 64 Memory at f8000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 1.0

00:01.0 Class 0604: 8086:7191 (rev 03)

	Flags: bus master, 66Mhz, medium devsel, latency 128
	Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
	I/O behind bridge: 00002000-00002fff
	Memory behind bridge: fc100000-fdffffff

00:04.0 Class 0401: 125d:1988 (rev 12)

	Subsystem: 1033:80f1
	Flags: bus master, medium devsel, latency 64, IRQ 10
	I/O ports at 1400 [size=256]
	Capabilities: [c0] Power Management version 2

00:06.0 Class 0200: 8086:1229 (rev 09)

	Subsystem: 8086:2411
	Flags: bus master, medium devsel, latency 66, IRQ 10
	Memory at fc020000 (32-bit, non-prefetchable) [size=4K]
	I/O ports at 1080 [size=64]
	Memory at fc000000 (32-bit, non-prefetchable) [size=128K]
	Expansion ROM at <unassigned> [disabled] [size=1M]
	Capabilities: [dc] Power Management version 2

00:06.1 Class 0700: 115d:00d3 (prog-if 02)

	Subsystem: 8086:2411
	Flags: medium devsel, IRQ 10
	I/O ports at 1068 [size=8]
	Memory at fc021000 (32-bit, non-prefetchable) [size=4K]
	Capabilities: [dc] Power Management version 2

00:07.0 Class 0601: 8086:7110 (rev 02)
Flags: bus master, medium devsel, latency 0

00:07.1 Class 0101: 8086:7111 (rev 01) (prog-if 80 [Master])

	Flags: bus master, medium devsel, latency 64
	I/O ports at 1070 [size=16]

00:07.2 Class 0c03: 8086:7112 (rev 01)

	Flags: bus master, medium devsel, latency 64, IRQ 5
	I/O ports at 10c0 [size=32]

00:07.3 Class 0680: 8086:7113 (rev 03)
Flags: medium devsel, IRQ 9

00:0c.0 Class 0607: 104c:ac51

	Subsystem: 1033:80cd
	Flags: bus master, medium devsel, latency 168, IRQ 10
	Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
	Memory window 0: 10400000-107ff000 (prefetchable)
	Memory window 1: 10800000-10bff000
	I/O window 0: 00004000-000040ff
	I/O window 1: 00004400-000044ff
	16-bit legacy interface ports at 0001

00:0c.1 Class 0607: 104c:ac51

	Subsystem: 1033:80cd
	Flags: bus master, medium devsel, latency 168, IRQ 5
	Memory at 10001000 (32-bit, non-prefetchable) [size=4K]
	Bus: primary=00, secondary=06, subordinate=09, sec-latency=176
	Memory window 0: 10c00000-10fff000 (prefetchable)
	Memory window 1: 11000000-113ff000
	I/O window 0: 00004800-000048ff
	I/O window 1: 00004c00-00004cff
	16-bit legacy interface ports at 0001

00:0d.0 Class 0c00: 1033:00ce (rev 01) (prog-if 10)

	Subsystem: 1033:00ce
	Flags: medium devsel, IRQ 10
	Memory at fc022000 (32-bit, non-prefetchable) [disabled] [size=4K]
	Capabilities: [60] Power Management version 2

01:00.0 Class 0300: 1002:4c4d (rev 64)

	Subsystem: 1033:80b7
	Flags: bus master, stepping, medium devsel, latency 66, IRQ 10
	Memory at fd000000 (32-bit, non-prefetchable) [size=16M]
	I/O ports at 2000 [size=256]
	Memory at fc100000 (32-bit, non-prefetchable) [size=4K]
	Expansion ROM at <unassigned> [disabled] [size=128K]
	Capabilities: [50] AGP version 1.0
	Capabilities: [5c] Power Management version 1