Skip to contentSkip to conversation

Unable to make kernel 2.6.8 up

DISCUSSION kernel kernel 2 participants 8 messages Oct 19, 2004 – Oct 21, 2004

lore
Share & tools
lore
#1 lore raw
Quoted 2 lines · kernel kernel

Hi all
While booting with 2.6.8 kernel. giving error no ata_piix module found.

Unless you have an Intel SATA contoler on your mobo, (and possably SATA disks) then i would imagen you could ignore this message, if you do have the above then "please" supply the needed info in your next reply.

What motherboard.
What chipsets does it have.
What disks do you have, make and model numbers please. Name of distro would also help.

It all comes down you you forgetting to include support for Intel SATA contolers which is to be found under;
SCSI low-level drivers
sub section;
CONFIG_SCSI_SATA
When chosing the above you will automaticly get the following "option";
CONFIG_SCSI_ATA_PIIX

Quoted 5 lines

How to solve it.

Thank
kh

Signature · 13 lines
If the Linux community is a bunch of thieves because they
try to imitate windows programs, then the Windows community
is built on organized crime.

Regards Richard
[email protected]
http://people.zeelandnet.nl/pa3gcu/

-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs
#2 lore raw

Hi Richard,
Thanks for your fast response.

I am furnishing the following details.
Motherboard : Intel 865
Processor : P4 2.4GHz
SCSI : Samsung Hard disk

I am trying to use 2.6.8 kernel from the GNU (downloaded from kernel.org)

Thanks
Amrith

Quoted 27 lines · Richard Adams
Quoted 2 lines · kernel kernel

Hi all
While booting with 2.6.8 kernel. giving error no ata_piix module found.

Unless you have an Intel SATA contoler on your mobo, (and possably SATA disks) then i would imagen you could ignore this message, if you do have the above then "please" supply the needed info in your next reply.

What motherboard.
What chipsets does it have.
What disks do you have, make and model numbers please. Name of distro would also help.

It all comes down you you forgetting to include support for Intel SATA contolers which is to be found under;
SCSI low-level drivers
sub section;
CONFIG_SCSI_SATA
When chosing the above you will automaticly get the following "option"; CONFIG_SCSI_ATA_PIIX

Quoted 5 lines

How to solve it.

Thank
kh

Quoted 10 lines

--
If the Linux community is a bunch of thieves because they try to imitate windows programs, then the Windows community is built on organized crime.

Regards Richard
[email protected]
http://people.zeelandnet.nl/pa3gcu/

-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs

#3 lore raw
Quoted 9 lines · kernel kernel

Hi  Richard,
Thanks for your fast response.

I am furnishing the following details.
Motherboard : Intel 865
Processor    : P4 2.4GHz
SCSI           : Samsung Hard disk

I am trying to use 2.6.8 kernel from the GNU (downloaded from kernel.org)

You said your problem was;

"While booting with 2.6.8 kernel. giving error no ata_piix module found"

Now you say you have a SCSI disk, the two are completly different, With SCSI its now the disk type which needs a driver but your SCSI controler. It will also need to be compiled into the kernel and NOT as a module.

Simply choose the needed driver with 'make config' or 'make menuconfig' recompile the kernel install it and update your bootloader then reboot.

You are being to vauge to help precisely, please learn to explain your problem(s) better.

Quoted 2 lines

Thanks
Amrith

Signature · 13 lines
If the Linux community is a bunch of thieves because they
try to imitate windows programs, then the Windows community
is built on organized crime.

Regards Richard
[email protected]
http://people.zeelandnet.nl/pa3gcu/

-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs
#4 lore raw

Hi Richard,
I was able to build it.
But while, boot up it is giving the error message init not found.

Thanks
Amrith

Quoted 31 lines · Richard Adams
Quoted 9 lines · kernel kernel

Hi Richard,
Thanks for your fast response.

I am furnishing the following details.
Motherboard : Intel 865
Processor : P4 2.4GHz
SCSI : Samsung Hard disk

I am trying to use 2.6.8 kernel from the GNU (downloaded from kernel.org)

You said your problem was;

"While booting with 2.6.8 kernel. giving error no ata_piix module found"

Now you say you have a SCSI disk, the two are completly different, With SCSI its now the disk type which needs a driver but your SCSI controler. It will also need to be compiled into the kernel and NOT as a module.

Simply choose the needed driver with 'make config' or 'make menuconfig' recompile the kernel install it and update your bootloader then reboot.

You are being to vauge to help precisely, please learn to explain your problem(s) better.

Quoted 2 lines

Thanks
Amrith

--

Quoted 9 lines

If the Linux community is a bunch of thieves because they try to imitate windows programs, then the Windows community is built on organized crime.

Regards Richard
[email protected]
http://people.zeelandnet.nl/pa3gcu/

-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs

#5 lore raw
Quoted 3 lines · kernel kernel

Hi Richard,
I was able to build it.
But while, boot up it is giving the error message init not found.

This could be cause by many things, but considering you mentioned SATA and then SCSI leads me to belive your new kernel is looking for a partition on a differently named drive than you think it is.
For example, some SATA drivers use scsi (emulation) meaning your old system has disks defined as /dev/hdX and the new kernel with SCSI or SATA devices looks for /dev/sdX

Without knowing what you are doing no one can really say what you need to do. I can point you to a search engine use "google.com/linux" as the address and type, "no init found" in the search engine, you will get a lot of information which may help you.

Quoted 2 lines

Thanks
Amrith

Signature · 13 lines
If the Linux community is a bunch of thieves because they
try to imitate windows programs, then the Windows community
is built on organized crime.

Regards Richard
[email protected]
http://people.zeelandnet.nl/pa3gcu/

-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs
#6 lore raw

Hi Richard.

I had a kernel patch and i need to test in the latest kernel. Before that i am trying to bring the kernel 2.6.x up and running. That is all i want to do.

By the way
vmlinux -- is the kernel
vmlinuz --- is the boot sector.

Why initrd is needed ?
While mkinitrd, I am getting the error /dev/mapper not found, But still it makes the initrd image.

Thanks
Amrith

Quoted 22 lines · Richard Adams
Quoted 3 lines · kernel kernel

Hi Richard,
I was able to build it.
But while, boot up it is giving the error message init not found.

This could be cause by many things, but considering you mentioned SATA and then SCSI leads me to belive your new kernel is looking for a partition on a differently named drive than you think it is.
For example, some SATA drivers use scsi (emulation) meaning your old system has disks defined as /dev/hdX and the new kernel with SCSI or SATA devices looks for /dev/sdX

Without knowing what you are doing no one can really say what you need to do. I can point you to a search engine use "google.com/linux" as the address and type, "no init found" in the search engine, you will get a lot of information which may help you.

Quoted 2 lines

Thanks
Amrith

Quoted 10 lines

--
If the Linux community is a bunch of thieves because they try to imitate windows programs, then the Windows community is built on organized crime.

Regards Richard
[email protected]
http://people.zeelandnet.nl/pa3gcu/

-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs

#7 lore raw
Quoted 5 lines · kernel kernel

Hi Richard.

I had a kernel patch and i need to test in the latest kernel. Before that i am trying to bring the kernel 2.6.x up and running. That is all i want to do.

Providing the patch you intend to use is for your kernel version why not.

Quoted 2 lines

By the way
vmlinux -- is the kernel

The kernel can be called anything you want it to be called its up to you.

Quoted 1 line

vmlinuz --- is the boot sector.

Is it.???

Quoted 2 lines

Why initrd is needed ?

If you compile your own kernel and "include" disk or card drivers which are needed to boot the system then you dont need initrd.

Quoted 2 lines

While mkinitrd, I am getting the error /dev/mapper not found, But still it makes the initrd image.

Never use initrd so i cant comment.

There are plenty of sites around giving upto date info on howto compile and use a 2.6 kernel, i suggest once more that you use google to get more info, it is full of it i can assure you.

Quoted 3 lines

Thanks
Amrith

Signature · 13 lines
If the Linux community is a bunch of thieves because they
try to imitate windows programs, then the Windows community
is built on organized crime.

Regards Richard
[email protected]
http://people.zeelandnet.nl/pa3gcu/

-
To unsubscribe from this list: send the line "unsubscribe linux-newbie" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.linux-learn.org/faqs