Skip to contentSkip to conversation

3ware driver broken with 2.4.22/23 ?

DISCUSSION Lukas Hejtmanek 5 participants 7 messages Dec 21, 2003 – Dec 29, 2003

lore
Share & tools
lore
#0 lore raw

Hello,

I have 3ware Escalade 8500-8 card with 8 SATA WD 250GB drives. I set up HW RAID5 configuration over all drives.
I'm using kernel 2.4.23 vanilla with XFS patch. RAID5 partition is formated to XFS.
System is single hyper threaded P4 Xeon 2.8GHz with 1GB of RAM. There is Intel 1000/PRO ethernet card. Motherboard is MSI E7501 Master-LS.

If I do:
iozone -Ra -g 20G -e -n 10485760
on the XFS partition then it freezes after certain time (but always the same amount if I run it again few times).

Server responds only to ping and sysrq. No process can be run and already running process top freezes as well. After about 8 hours it is still freezed. If I connect monitor to the server when it freezes then monitor indicates - no signal.

I use configuration with SMP without HIGHMEM. However it happens without SMP as well. (Driver: 1.02.00.036)

With kernel 2.6.0 it seems to be ok. (Driver: 1.02.00.037)

Here is lspci:
00:00.0 Host bridge: Intel Corp. E7501 Memory Controller Hub (rev 01)
00:00.1 Class ff00: Intel Corp. E7000 Series Host RASUM Controller (rev 01) 00:02.0 PCI bridge: Intel Corp. E7000 Series Hub Interface B PCI-to-PCI Bridge (rev 01) 00:02.1 Class ff00: Intel Corp. E7000 Series Hub Interface B RASUM Controller (rev 01) 00:1d.0 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #1) (rev 02)
00:1d.1 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #2) (rev 02)
00:1d.2 USB Controller: Intel Corp. 82801CA/CAM USB (Hub #3) (rev 02)
00:1e.0 PCI bridge: Intel Corp. 82801BA/CA/DB/EB PCI Bridge (rev 42)
00:1f.0 ISA bridge: Intel Corp. 82801CA LPC Interface Controller (rev 02) 00:1f.1 IDE interface: Intel Corp. 82801CA Ultra ATA Storage Controller (rev 02) 00:1f.3 SMBus: Intel Corp. 82801CA/CAM SMBus Controller (rev 02)
01:1c.0 PIC: Intel Corp. 82870P2 P64H2 I/OxAPIC (rev 04)
01:1d.0 PCI bridge: Intel Corp. 82870P2 P64H2 Hub PCI Bridge (rev 04)
01:1e.0 PIC: Intel Corp. 82870P2 P64H2 I/OxAPIC (rev 04)
01:1f.0 PCI bridge: Intel Corp. 82870P2 P64H2 Hub PCI Bridge (rev 04)
02:09.0 Ethernet controller: Intel Corp. 82545EM Gigabit Ethernet Controller (Copper) (rev 01) 02:0c.0 RAID bus controller: 3ware Inc 3ware 7000-series ATA-RAID (rev 01) 04:04.0 Ethernet controller: Intel Corp. 82540EM Gigabit Ethernet Controller (rev 02) 04:05.0 VGA compatible controller: ATI Technologies Inc Rage XL (rev 27)

Here is info from 3ware card:
Monitor version: ME7X 1.01.00.035
Firmware version: FE7S 1.05.00.036
BIOS version: BE7X 1.08.00.044
PCB version: Rev3
Achip version: V3.20
Pchip version: V1.30
Model: 8500-8

Can firmware upgrade help? Or there is an issue with something other not related to 3ware card?

Signature · 1 line
Lukáš Hejtmánek
#1 lore raw
Quoted 19 lines · Lukas Hejtmanek

Hello,

I have 3ware Escalade 8500-8 card with 8 SATA WD 250GB drives. I set up HW RAID5 configuration over all drives.
I'm using kernel 2.4.23 vanilla with XFS patch. RAID5 partition is formated to XFS.
System is single hyper threaded P4 Xeon 2.8GHz with 1GB of RAM. There is Intel 1000/PRO ethernet card. Motherboard is MSI E7501 Master-LS.

If I do:
iozone -Ra -g 20G -e -n 10485760
on the XFS partition then it freezes after certain time (but always the same amount if I run it again few times).

Server responds only to ping and sysrq. No process can be run and already running process top freezes as well. After about 8 hours it is still freezed. If I connect monitor to the server when it freezes then monitor indicates - no signal.

Quoted 8 lines

I use configuration with SMP without HIGHMEM. However it happens without SMP as well. (Driver: 1.02.00.036)

With kernel 2.6.0 it seems to be ok. (Driver: 1.02.00.037)

Can firmware upgrade help? Or there is an issue with something other not related to 3ware card?

Well, it happens from time to time that the card refuses to work with an actual driver as actual drivers sometimes make use of functions introduced in firmware upgrades. Upgrading the firmware should be the first thing to try. Chances are it works well even with 2.4 afterwards.

Quoted 7 lines
Signature · 6 lines
Luká? Hejtmánek
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected]
More majordomo info at  http://vger.kernel.org/majordomo-info.html
Please read the FAQ at  http://www.tux.org/lkml/
Signature · 4 lines
  .''`.   Martin Loschwitz           Debian GNU/Linux developer
 : :'  :  [email protected]        [email protected]
 `. `'`   http://www.madkiss.org/    people.debian.org/~madkiss/
   `-     Use Debian GNU/Linux 3.0!  See http://www.debian.org/
#2 lore raw
In reply to Lukas Hejtmanek
Quoted 6 lines · Lukas Hejtmanek

Hello,

I have 3ware Escalade 8500-8 card with 8 SATA WD 250GB drives. I set up HW RAID5 configuration over all drives.
I'm using kernel 2.4.23 vanilla with XFS patch. RAID5 partition is formated to XFS.

Reproducing with a different filesystem would probably be a useful datapoint.

#3 lore raw
In reply to Lukas Hejtmanek
Quoted 4 lines · Lukas Hejtmanek

Can firmware upgrade help? Or there is an issue with something other not related to 3ware card?

Generally not with such a small rev difference. You could try the
latest driver, and firmware in the 7.7. The driver source is on the Red Hat drivers disk. You should be able to drop in the .c, and .h in drivers/scsi, and recompile.
http://3ware.com/support/download.asp?code=5&id=7.7.0&softtype=Driver&releasenotes=&os=Windows

PS- Personally I'd suspect an XFS bug. Try reiserfs. I've been running 2.4.23pres, and 2.4.23 on hundreds of 3ware of numerous different types.
With no issue with the prior firmware release.

Signature · 4 lines
There is no such thing as obsolete hardware.
Merely hardware that other people don't want.
(The Second Rule of Hardware Acquisition)
Sam Flory  <[email protected]>
#4 lore raw
Quoted 10 lines

Generally not with such a small rev difference. You could try the
latest driver, and firmware in the 7.7. The driver source is on the Red Hat drivers disk. You should be able to drop in the .c, and .h in drivers/scsi, and recompile.
http://3ware.com/support/download.asp?code=5&id=7.7.0&softtype=Driver&releasenotes=&os=Windows

PS- Personally I'd suspect an XFS bug. Try reiserfs. I've been running 2.4.23pres, and 2.4.23 on hundreds of 3ware of numerous different types.
With no issue with the prior firmware release.

There are a lot of people, running RAID5 3ware's w/ Terrabyte arrays. I don't want to say it is not an XFS bug, but I find that highly suspect.

js

Signature · 3 lines
VB programmers ask why no one takes them seriously, 
it's somewhat akin to a McDonalds manager asking employees 
why they don't take their 'career' seriously.
#5 lore raw
Quoted 7 lines · Joshua Schmidlkofer
Quoted 7 lines

Generally not with such a small rev difference. You could try the
latest driver, and firmware in the 7.7. The driver source is on the Red Hat drivers disk. You should be able to drop in the .c, and .h in drivers/scsi, and recompile.
http://3ware.com/support/download.asp?code=5&id=7.7.0&softtype=Driver&releasenotes=&os=Windows

Quoted 6 lines
Quoted 3 lines

PS- Personally I'd suspect an XFS bug. Try reiserfs. I've been running 2.4.23pres, and 2.4.23 on hundreds of 3ware of numerous different types.
With no issue with the prior firmware release.

There are a lot of people, running RAID5 3ware's w/ Terrabyte arrays. I don't want to say it is not an XFS bug, but I find that highly suspect.

Well, with ext3 parition iozone program finishes OK. So it looks like some XFS bug.

Signature · 1 line
Lukáš Hejtmánek
#6 lore raw
Quoted 12 lines · Lukas Hejtmanek
Quoted 11 lines · Joshua Schmidlkofer
Quoted 10 lines

Generally not with such a small rev difference. You could try the
latest driver, and firmware in the 7.7. The driver source is on the Red Hat drivers disk. You should be able to drop in the .c, and .h in drivers/scsi, and recompile.
http://3ware.com/support/download.asp?code=5&id=7.7.0&softtype=Driver&releasenotes=&os=Windows

PS- Personally I'd suspect an XFS bug. Try reiserfs. I've been running 2.4.23pres, and 2.4.23 on hundreds of 3ware of numerous different types.
With no issue with the prior firmware release.

Quoted 5 lines
Quoted 2 lines

There are a lot of people, running RAID5 3ware's w/ Terrabyte arrays. I don't want to say it is not an XFS bug, but I find that highly suspect.

Well, with ext3 parition iozone program finishes OK. So it looks like some XFS bug.

FWIW have you sent this on to the XFS list?

thanks,
Joshua