Skip to contentSkip to conversation

pand Connection refused(111) when connecting to a Belkin NAP

Bluez-devel Dave Henriksen 2 participants 3 messages Jan 21, 2004 1 message not in the archive Bluetooth drivers

lore
Share & tools
lore
#0 lore raw

Hi,

I'm wondering what may be causing a "Connection refused(111)" message when I issue a "pand --connect 00:02:72:00:DC:F1" command to connect to
a Belkin NAP. The proper pins are setup, and I can l2ping the NAP, I
just can't get pand to connect to it. Any help would be greatly
appreciated. I know that when I do networking through this NAP on the
Windows side, I need to specify and id/password combination in addition to a pin. I'm not sure how to do this in Linux.

Thanks,

Dave H

log info:

Jan 21 11:28:51 linux pand[2711]: PAN daemon ver 1.1
Jan 21 11:28:51 linux pand[2711]: Connecting to 00:02:72:00:DC:F1
Jan 21 11:28:53 linux hcid[2690]:
link_key_request(sba=00:0D:88:AC:BE:C5, dba=0 0:02:72:00:DC:F1)
Jan 21 11:28:54 linux pand[2711]: Connect to 00:02:72:00:DC:F1 failed.

Connection refused(111)

-------------------------------------------------------
The SF.Net email is sponsored by EclipseCon 2004 Premiere Conference on Open Tools Development and Integration See the breadth of Eclipse activity. February 3-5 in Anaheim, CA.
http://www.eclipsecon.org/osdn
_______________________________________________
Bluez-devel mailing list [email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-devel

maintainer
#1 lore raw

Hi Dave,

Quoted 7 lines

I'm wondering what may be causing a "Connection refused(111)" message when I issue a "pand --connect 00:02:72:00:DC:F1" command to connect to
a Belkin NAP. The proper pins are setup, and I can l2ping the NAP, I
just can't get pand to connect to it. Any help would be greatly
appreciated. I know that when I do networking through this NAP on the
Windows side, I need to specify and id/password combination in addition to a pin. I'm not sure how to do this in Linux.

run "hcidump -w <file>" and send us the dump.

Regards

Marcel

-------------------------------------------------------
The SF.Net email is sponsored by EclipseCon 2004 Premiere Conference on Open Tools Development and Integration See the breadth of Eclipse activity. February 3-5 in Anaheim, CA.
http://www.eclipsecon.org/osdn
_______________________________________________
Bluez-devel mailing list [email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-devel

A message that is not in the archive (sent off-list or not yet received): [email protected]

maintainer
#3 lore raw

Hi Dave,

Quoted 1 line

Here is the file from the hcidump.

	> ACL data: handle 0x0029 flags 0x02 dlen 16
	    L2CAP(s): Connect rsp: dcid 0x0000 scid 0x0040 result 2 status 0

The result code 2 means "Connection refused - PSM not supported". Are you sure this AP supports the PAN Profile. Try using dund instead.

Regards

Marcel

-------------------------------------------------------
The SF.Net email is sponsored by EclipseCon 2004 Premiere Conference on Open Tools Development and Integration See the breadth of Eclipse activity. February 3-5 in Anaheim, CA.
http://www.eclipsecon.org/osdn
_______________________________________________
Bluez-devel mailing list [email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-devel