SCSI update for 2.6.3

The current crop of accumulated patches are mainly driver updates and bug fixes.

It is available at

bk://linux-scsi.bkbits.net/scsi-for-linus

The short changelog is:

<brking:us.ibm.com>:
o SCSI: Make retries obey host_self_blocked flag

Andrew Vasquez:
o qla2xxx -- FCP_RSP IU check during command completion
o qla2xxx -- Properly schedule mailbox command timeouts

Christoph Hellwig:
o move remaining definitions from drivers/scsi/scsi.h to include/scsi
o fix up NCR5380 private data
o fix up ini9100 interrupt handling
o Remove CONFIG_SCSI_DC390T_NOGENSUPP
o remove flush_cache_all() from qla1280

David S. Miller:
o qla2xxx: remove flush_cache_all

Geert Uytterhoeven:
o Sun-3x ESP SCSI clean up
o NCR53C9x slave_{alloc,destroy}()

James Bottomley:
o SCSI: 53c700: reduce default tag depth to 4
o MPT Fusion driver 3.00.03 update

Kai Mäkisara:
o Sysfs class support for SCSI tapes

Mark Haverkamp:
o aacraid reset handler
o add card types to aacraid driver

Patrick Mansfield:
o have CONFIG_SCSI_PROC_FS depend on CONFIG_PROC_FS

James

-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

Has this been checked for correctness, or will Al flame me to a crisp for accepting it? Pls verify..

Linus
-
To unsubscribe from this list: send the line "unsubscribe linux-scsi" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html

Hi James,
I am getting a panic out of the 2.6.3 Fusion driver when no devices
are attached to it. Does the above update fix it? If so, I would like to get a copy of the above in patch form. If not, I can send you a copy of my boot log.

Regards,
Joe

Well, without a bug report I don't really have any idea.

The patch is here:

http://marc.theaimsgroup.com/?l=linux-scsi&m=107670916906716&w=2

James

Hi James,
Tried the patch, no luck. The panic is on an Opteron board which has an IDE rather than a SCSI disk. I have another system, identical to the above, that has a SCSI rather than IDE disk, and it boots. 2.6.1 boots on both systems.

Regards,
Joe

...
Using anticipatory io scheduler
FDC 0 is a post-1991 82077
loop: loaded (max 8 devices)
Intel(R) PRO/1000 Network Driver - version 5.2.30.1-k1
Copyright (c) 1999-2004 Intel Corporation.
tg3.c:v2.6 (February 3, 2004)
eth0: Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)] (PCI:33MHz:64-bit) 10/100/1000BaseT Ethernet 00:e0:81:51:d8:fd
eth1: Tigon3 [partno(BCM95704A7) rev 2003 PHY(5704)] (PCI:33MHz:64-bit) 10/100/1000BaseT Ethernet 00:e0:81:51:d8:fe Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
AMD8111: IDE controller at PCI slot 0000:00:07.1
AMD8111: chipset revision 3
AMD8111: not 100% native mode: will probe irqs later
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
AMD8111: 0000:00:07.1 (rev 03) UDMA133 controller

    ide0: BM-DMA at 0xffa0-0xffa7, BIOS settings: hda:DMA, hdb:pio
    ide1: BM-DMA at 0xffa8-0xffaf, BIOS settings: hdc:DMA, hdd:pio

hda: ST380011A, ATA DISK drive
isa bounce pool size: 16 pages
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
hdc: CD-950E/TKU, ATAPI CD/DVD-ROM drive
ide1 at 0x170-0x177,0x376 on irq 15
hda: max request size: 1024KiB
hda: 156301488 sectors (80026 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100)
/dev/ide/host0/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 >
hdc: ATAPI 52X CD-ROM drive, 128kB Cache, DMA
Uniform CD-ROM driver Revision: 3.20
Red Hat/Adaptec aacraid driver (1.1.2-lk1 Feb 24 2004)
Fusion MPT base driver 3.00.03
Copyright (c) 1999-2003 LSI Logic Corporation
mptbase: Initiating ioc0 bringup
mptbase: ioc0: ERROR - Doorbell ACK timeout(2)!
mptbase: ioc0: ERROR - Diagnostic reset FAILED! (102h)
mptbase: ioc0 NOT READY WARNING!
mptbase: WARNING - ioc0 did not initialize properly! (-1)
mptbase: probe of 0000:02:0a.0 failed with error -1
mptbase: Initiating ioc1 bringup
mptbase: ioc1: ERROR - Doorbell ACK timeout(2)!
mptbase: ioc1: ERROR - Diagnostic reset FAILED! (102h)
mptbase: ioc1 NOT READY WARNING!
mptbase: WARNING - ioc1 did not initialize properly! (-1)
mptbase: probe of 0000:02:0a.1 failed with error -1
Fusion MPT SCSI Host driver 3.00.03

Unable to handle kernel NULL pointer dereference at 0000000000000018 RIP: 
<ffffffff80823a1f>{mptscsih_init+175}PML4 0 
Oops: 0000 [1]
CPU 0 
Pid: 1, comm: swapper Not tainted
RIP: 0010:[<ffffffff80823a1f>] <ffffffff80823a1f>{mptscsih_init+175}
RSP: 0000:000001007afe1f18  EFLAGS: 00010202
RAX: 0000000000000000 RBX: 00000100089a4d20 RCX: 000000000000000c
RDX: 00000100089a4d20 RSI: ffffffff804546b0 RDI: 000001017fe1f398
RBP: 0000000000000001 R08: 0000000000000000 R09: 0000000000000000
R10: 000001017fdfa160 R11: 00000000000000c0 R12: 0000000000000000
R13: 0000000000000000 R14: 0000000000000000 R15: 0000000000000000
FS:  0000000000000000(0000) GS:ffffffff807fa540(0000) knlGS:0000000000000000
CS:  0010 DS: 0018 ES: 0018 CR0: 000000008005003b
CR2: 0000000000000018 CR3: 0000000000101000 CR4: 00000000000006a0
Process swapper (pid: 1, stackpage=10008898500)
Stack: ffffffff8082fb70 ffffffff8080788d 0000000000000246 0000000000000000 
       0000000000000000 ffffffff8010b16e 0000000000000000 ffffffff8010fec7 
       0000000000000000 0000000000000000 
Call Trace:<ffffffff8080788d>{do_initcalls+77} <ffffffff8010b16e>{init+110} 
       <ffffffff8010fec7>{child_rip+8} <ffffffff8010b100>{init+0} 
       <ffffffff8010febf>{child_rip+0} 

Code: 48 8b 70 18 e8 68 d4 c2 ff 48 89 df e8 50 66 c2 ff 48 85 c0 

RIP <ffffffff80823a1f>{mptscsih_init+175} RSP <000001007afe1f18>
CR2: 0000000000000018
<0>Kernel panic: Attempted to kill init!