RME HDSP 9652 syncing problem
Hi,
I have been using the RME HDSP 9652 for several months now and have noticed a problem with the synchonisation.
I have an external word clock which runs into 2 RME analog/digital interfaces, as well as the HDSP itself.
The HDSP is setup to sync to word clock input, and sample clock source is autosync.
The problem I am seeing is that if I transmit to 24 x 48kHz channels, then the first 8 channels (ADAT-1) seem to continuously loose their Sync status and I can pops (nulls) and clicks (spikes) in the recorded data (by looping the transmit back into receive). Running hdspmixer also shows the levels of the first 8 channels jumping around as the sync is lost.
Does anyone know what could be causing this problem? I have attached information about the system that I think is relevant.
Thanks
Ryan Winter
--
This email is confidential and intended solely for the use of the individual to whom it is addressed. Any views or opinions presented are solely those of the author and do not necessarily represent those of NAUTRONIX LTD.
If you are not the intended recipient, you have received this email in error and use, dissemination, forwarding, printing, or copying of this email is strictly prohibited. If you have received this email in error please contact the sender.
Although our computer systems use active virus protection software, and we take various measures to reduce the risk of viruses being transmitted in e-mail messages and attachments sent from this company, we cannot guarantee that such e-mail messages and attachments are free from viruses on receipt. It is a condition of our using e-mail to correspond with you, that any and all liability on our part arising directly or indirectly out of any virus is excluded. Please ensure that you run virus checking software on all e-mail messages and attachments before reading them.
RME Hammerfall HDSP 9652 (Card #1)
Buffers: capture f7200000 playback f7000000
IRQ: 9 Registers bus: 0xe1000000 VM: 0xf8a05000
Control register: 0x100a0ef
Control2 register: 0x800
Status register: 0x607dcce
Status2 register: 0xffff8479
FIFO status: 0
MIDI1 Output status: 0xffffff00
MIDI1 Input status: 0xffffff00
MIDI2 Output status: 0xffffff00
MIDI2 Input status: 0xffffff00
Buffer Size (Latency): 8192 samples (2 periods of 32768 bytes) Hardware pointer (frames): 8192
Passthru: no
Line out: on
Firmware version: 1
Sample Clock Source: AutoSync
Preferred Sync Reference: Word Clock
AutoSync Reference: Word Clock
AutoSync Frequency: 48000
System Clock Mode: Slave
System Clock Frequency: 48000
IEC958 input: Internal
IEC958 output: Coaxial only
IEC958 quality: Consumer
IEC958 emphasis: off
IEC958 NonAudio: off
IEC958 sample rate: Error flag set
ADAT1: Sync
ADAT2: Sync
ADAT3: Sync
SPDIF: No Lock
Word Clock: Sync
ADAT Sync: No Lock
numid=23,iface=HWDEP,name='ADAT Lock Status',index=1
; type=ENUMERATED,access=r----,values=1,items=3
; Item #0 'No Lock'
; Item #1 'Lock'
; Item #2 'Sync'
: values=2
numid=24,iface=HWDEP,name='ADAT Lock Status',index=2
; type=ENUMERATED,access=r----,values=1,items=3
; Item #0 'No Lock'
; Item #1 'Lock'
; Item #2 'Sync'
: values=2
numid=25,iface=HWDEP,name='ADAT Lock Status',index=3
; type=ENUMERATED,access=r----,values=1,items=3
; Item #0 'No Lock'
; Item #1 'Lock'
; Item #2 'Sync'
: values=2
numid=20,iface=HWDEP,name='ADAT Sync Lock Status'
; type=ENUMERATED,access=r----,values=1,items=3
; Item #0 'No Lock'
; Item #1 'Lock'
; Item #2 'Sync'
: values=0
numid=26,iface=HWDEP,name='Analog Extension Board'
; type=BOOLEAN,access=rw---,values=1
: values=off
numid=14,iface=HWDEP,name='AutoSync Reference'
; type=ENUMERATED,access=r----,values=1,items=7
; Item #0 'Word'
; Item #1 'ADAT Sync'
; Item #2 'IEC958'
; Item #3 'None'
; Item #4 'ADAT1'
; Item #5 'ADAT2'
; Item #6 'ADAT3'
: values=0
numid=9,iface=HWDEP,name='IEC958 Emphasis Bit'
; type=BOOLEAN,access=rw---,values=1
: values=off
numid=10,iface=HWDEP,name='IEC958 Non-audio Bit'
; type=BOOLEAN,access=rw---,values=1
: values=off
numid=7,iface=HWDEP,name='IEC958 Output also on ADAT1'
; type=BOOLEAN,access=rw---,values=1
: values=off
numid=8,iface=HWDEP,name='IEC958 Professional Bit'
; type=BOOLEAN,access=rw---,values=1
: values=off
numid=22,iface=HWDEP,name='Line Out'
; type=BOOLEAN,access=rw---,values=1
: values=on
numid=5,iface=HWDEP,name='Mixer'
; type=INTEGER,access=rw---,values=3,min=0,max=65536,step=1 : values=0,0,0
numid=21,iface=HWDEP,name='Passthru'
; type=BOOLEAN,access=rw---,values=1
: values=off
numid=13,iface=HWDEP,name='Preferred Sync Reference'
; type=ENUMERATED,access=rw---,values=1,items=6
; Item #0 'Word'
; Item #1 'IEC958'
; Item #2 'ADAT1'
; Item #3 'ADAT Sync'
; Item #4 'ADAT2'
; Item #5 'ADAT3'
: values=0
numid=19,iface=HWDEP,name='SPDIF Lock Status'
; type=ENUMERATED,access=r----,values=1,items=3
; Item #0 'No Lock'
; Item #1 'Lock'
; Item #2 'Sync'
: values=0
numid=15,iface=HWDEP,name='SPDIF Sample Rate'
; type=ENUMERATED,access=r----,values=1,items=7
; Item #0 '32000'
; Item #1 '44100'
; Item #2 '48000'
; Item #3 '64000'
; Item #4 '88200'
; Item #5 '96000'
; Item #6 'None'
: values=6
numid=12,iface=HWDEP,name='System Clock Mode'
; type=ENUMERATED,access=r----,values=1,items=2
; Item #0 'Master'
; Item #1 'Slave'
: values=1
numid=16,iface=HWDEP,name='System Sample Rate'
; type=INTEGER,access=r----,values=1,min=0,max=0,step=0 : values=48000
numid=18,iface=HWDEP,name='Word Clock Lock Status'
; type=ENUMERATED,access=r----,values=1,items=3
; Item #0 'No Lock'
; Item #1 'Lock'
; Item #2 'Sync'
: values=2
numid=3,iface=MIXER,name='IEC958 Playback Con Mask'
; type=IEC958,access=r----,values=1
: values=?
numid=4,iface=MIXER,name='IEC958 Playback Pro Mask'
; type=IEC958,access=r----,values=1
: values=?
numid=17,iface=PCM,name='External Rate'
; type=ENUMERATED,access=r----,values=1,items=7
; Item #0 '32000'
; Item #1 '44100'
; Item #2 '48000'
; Item #3 '64000'
; Item #4 '88200'
; Item #5 '96000'
; Item #6 'None'
: values=2
numid=6,iface=PCM,name='IEC958 Input Connector'
; type=ENUMERATED,access=rw---,values=1,items=3
; Item #0 'Optical'
; Item #1 'Coaxial'
; Item #2 'Internal'
: values=2
numid=1,iface=PCM,name='IEC958 Playback Default'
; type=IEC958,access=rw---,values=1
: values=?
numid=2,iface=PCM,name='IEC958 Playback PCM Stream'
; type=IEC958,access=rw---,values=1
: values=?
numid=11,iface=PCM,name='Sample Clock Source'
; type=ENUMERATED,access=rw---,values=1,items=7
; Item #0 'AutoSync'
; Item #1 'Internal 32.0 kHz'
; Item #2 'Internal 44.1 kHz'
; Item #3 'Internal 48.0 kHz'
; Item #4 'Internal 64.0 kHz'
; Item #5 'Internal 88.2 kHz'
; Item #6 'Internal 96.0 kHz'
: values=0
Quoted 18 lines
Hi,
I have been using the RME HDSP 9652 for several months now and have noticed a problem with the synchonisation.
I have an external word clock which runs into 2 RME analog/digital interfaces, as well as the HDSP itself.
The HDSP is setup to sync to word clock input, and sample clock source is autosync.
The problem I am seeing is that if I transmit to 24 x 48kHz channels, then the first 8 channels (ADAT-1) seem to continuously loose their Sync status and I can pops (nulls) and clicks (spikes) in the recorded data (by looping the transmit back into receive). Running hdspmixer also shows the levels of the first 8 channels jumping around as the sync is lost.
Quoted 7 lines
Does anyone know what could be causing this problem? I have attached information about the system that I think is relevant.
Thanks
Ryan Winter
Hi Ryan,
I can't see any problem with your software setup. Moreover the alsa controls you use for this are basically only wrappers to hardware registers, so I would tend to think that your problem is hardware related. What comes to my mind immediately, rather than a faulty card (though it's possible), would be a faulty cable or a problem in the WordClock chain. I suppose all the external converters you use are slaved to the same device as the card, so maybe one of those converters is defective or wired with a faulty WordClock cable or termination. What happens if you swap the converters ADAT ports ? Do you still get sync issues only on ADAT-1 ? For the pops and clicks issue, how do you loop the transmit back into the receive ?
Thomas
-------------------------------------------------------
This SF.Net email is sponsored by: SourceForge.net Broadband Sign-up now for SourceForge Broadband and get the fastest 6.0/768 connection for only $19.95/mo for the first 3 months!
http://ads.osdn.com/?ad_id=2562&alloc_id=6184&op=click
Quoted 40 lines · Thomas Charbonnel
Quoted 18 lines
Hi,
I have been using the RME HDSP 9652 for several months now and have noticed a problem with the synchonisation.
I have an external word clock which runs into 2 RME analog/digital interfaces, as well as the HDSP itself.
The HDSP is setup to sync to word clock input, and sample clock source is autosync.
The problem I am seeing is that if I transmit to 24 x 48kHz channels, then the first 8 channels (ADAT-1) seem to continuously loose their Sync status and I can pops (nulls) and clicks (spikes) in the recorded data (by looping the transmit back into receive). Running hdspmixer also shows the levels of the first 8 channels jumping around as the sync is lost.
Quoted 7 lines
Does anyone know what could be causing this problem? I have attached information about the system that I think is relevant.
Thanks
Ryan WinterHi Ryan,
I can't see any problem with your software setup. Moreover the alsa controls you use for this are basically only wrappers to hardware registers, so I would tend to think that your problem is hardware related. What comes to my mind immediately, rather than a faulty card (though it's possible), would be a faulty cable or a problem in the WordClock chain. I suppose all the external converters you use are slaved to the same device as the card, so maybe one of those converters is defective or wired with a faulty WordClock cable or termination. What happens if you swap the converters ADAT ports ? Do you still get sync issues only on ADAT-1 ? For the pops and clicks issue, how do you loop the transmit back into the receive ?
Quoted 1 line
Thomas
I ended up swapping the optical cables around and found one that was slightly damaged (well almost severed actually). We are getting some higher quality optical cables in but preliminary tests look good.
Thanks for the tip, I should have known it would be hardware related :D
Ryan Winter
Signature · 21 lines
Apologies for below. -- This email is confidential and intended solely for the use of the individual to whom it is addressed. Any views or opinions presented are solely those of the author and do not necessarily represent those of NAUTRONIX LTD. If you are not the intended recipient, you have received this email in error and use, dissemination, forwarding, printing, or copying of this email is strictly prohibited. If you have received this email in error please contact the sender. Although our computer systems use active virus protection software, and we take various measures to reduce the risk of viruses being transmitted in e-mail messages and attachments sent from this company, we cannot guarantee that such e-mail messages and attachments are free from viruses on receipt. It is a condition of our using e-mail to correspond with you, that any and all liability on our part arising directly or indirectly out of any virus is excluded. Please ensure that you run virus checking software on all e-mail messages and attachments before reading them. ------------------------------------------------------- This SF.Net email is sponsored by: Oracle 10g Get certified on the hottest thing ever to hit the market... Oracle 10g. Take an Oracle 10g class now, and we'll give you the exam FREE. http://ads.osdn.com/?ad_id=3149&alloc_id=8166&op=click