Skip to contentSkip to conversation

Passive FTP Problem in NAT.

DISCUSSION [email protected] 3 participants 3 messages Sep 15, 2004

lore
Share & tools
lore
#0 lore raw

Hi.

Could someone help me or give me advice regarding NAT on a FTP server located in my DMZ.

This is my setup :

My Firewall(Linux 2.4.22-1) :
|
- eth0 = Public Interface (x.x.x.66 / 26 )
|
- eth1 = DMZ Interface (172.16.100.254 / 24 )
|
- eth2 = My Internal Network ( 192.168.1.1 / 24 )

I have a FTP server located on my DMZ Network. The server is listening on a �non-standard� ftp port. It listens on port : 2121.

To generate my firewall config I use FwBuilder. I�ve tried many configurations but, I never get the data port to open( e.g. to list a directory)

In my configuration I�ve allowed, and NAT�ed the following services to my FTP server located on the DMZ :

FTP = TCP Destination Port : Start : 2121 � End : 2121
FTP_DATA = TCP Source Port : Start : 20 � End : 20

			        Destination : Start : 1024 � End : 65535

I can connect, but cannot list the directories.

p.s. I�m running Proftpd on my FTP server. I have also tried to configure the �PassivePorts= 60000 65534� to configure a group of the passive ports. But it�s the same issue with the directory listening.

Any help would be much appreciated.

Best regards to all,

Svavar O
Reykjavik - Iceland

#1 lore raw
Quoted 6 lines · [email protected] wrote:

I have a FTP server located on my DMZ Network. The server is listening on a “non-standard” ftp port. It listens on port : 2121.

To generate my firewall config I use FwBuilder. I’ve tried many configurations but, I never get the data port to open( e.g. to list a directory)

In my configuration I’ve allowed, and NAT’ed the following services to my FTP server located on the DMZ :

Quoted 8 lines

FTP = TCP Destination Port : Start : 2121 – End : 2121
FTP_DATA = TCP Source Port : Start : 20 – End : 20

			        Destination : Start : 1024 – End : 65535

I can connect, but cannot list the directories.

p.s. I’m running Proftpd on my FTP server. I have also tried to configure the “PassivePorts= 60000 65534” to configure a group of the passive ports. But it’s the same issue with the directory listening.

Without having a look into your actual rules (or relevant part of it), it is hard to tell what is wrong. Neiter me (nor most people here) can't guess what would be the rules generated by FwBuilder. Give us actual rules, somebody might spot what is wrong, and than you can try to get FwBuiler to generate correct rules.

My guesses would be that you either:

a) did not load ip_nat_ftp module (it doesn't get loaded automatically)

b) failed to specify that your FTP server is on non-default port (from documentation --m helper --helper ftp-2121, but I haven't tested if this will suffice, maybe you also need to pass port number to module directly).

c) first packet of data connection is going to be in RELATED state (not NEW), if you have ip_nat_ftp loaded (which in turn loads ip_conntrack_ftp).

d) most important of all: passive FTP data transfers do not use port 20.
Both ports (source and destination) should be 1024+. This is because
connection is from client to server. Port 20 is used by active FTP data transfers (and connection is from server to client).

Signature · 3 lines
Aleksandar Milivojevic <[email protected]>    Pollard Banknote Limited
Systems Administrator                           1499 Buffalo Place
Tel: (204) 474-2323 ext 276                     Winnipeg, MB  R3T 1L7
#2 lore raw
In reply to [email protected]
Quoted 15 lines · On Wed, 2004-09-15 at 11:13, [email protected] wrote:

Hi.

Could someone help me or give me advice regarding NAT on a FTP server located in my DMZ.

This is my setup :

My Firewall(Linux 2.4.22-1) :
|
- eth0 = Public Interface (x.x.x.66 / 26 )
|
- eth1 = DMZ Interface (172.16.100.254 / 24 )
|
- eth2 = My Internal Network ( 192.168.1.1 / 24 )

Quoted 1 line

I have a FTP server located on my DMZ Network. The server is listening on a non-standard ftp port. It listens on port : 2121.

bingo. the standard modprobe commands won't work in your situation. try:

        modprobe ip_conntrack_ftp ports=21,2121
        modprobe ip_nat_ftp ports=21,2121

to force the helper to watch your specific port.

-j

Signature · 1 line
Jason Opperisano <[email protected]>