HP C2502 SCSI card (NCR 53C400A based) not working
Hello,
I have an old ISA SCSI card that came with HP ScanJet IIP scanner. It's
HP C2502 card based on NCR 53C400A chip. I was unable to get it working
with g_NCR5380 driver so I tried loading the official MINI400I.SYS
driver in DOSemu. I was surprised that the values sent to the ports are not the same as in the g_NCR5380 driver.
The g_NCR5380 driver uses these "magic outbs" to configure the card (this sequence disables the card):outb(0x59, 0x779);outb(0xb9, 0x379);outb(0xc5, 0x379);outb(0xae, 0x379);outb(0xa6, 0x379);outb(0x00, 0x379);
This is the output from DOSemu:
779 < f
379 < 22
379 < f0
379 < 20
379 < 80
379 < 00
The magic numbers are different - so I have a card that is not supported by the driver. I've changed the numbers in the driver to match my card but I'm still unable to get it working.
The g_NCR5380 driver uses this to check if the card is present at a particular base address:
outb(0xc0, ports[i] + 9);
if (inb(ports[i] + 9) != 0x80)
continue;
The MINI400I.SYS uses something different:
(this is failed presence test at base address 0x280) 28e < 25
28f < a5
28f > ff
(this looks like a successful test at base address 0x350) 35e < 25
35f < a5
35f > a5
35f < 5a
35f > 5a
35e < 0
35f < 0
359 < 80
359 < 10
351 < 0
352 < 0
353 < 0
354 < 0
357 > ff
359 < 80
359 < 10
351 < 0
352 < 0
353 < 0
354 < 0
357 > ff
351 < 80
351 < 0
357 > ff
According to this, I think that my card has the 53C400A chip registers mapped to different addresses (offsets) but I'm unable to determine what the mapping is. I was also unable to find the 53C400A datasheet which might help a bit.
Signature · 1 line
Ondrej Zary
Quoted 6 lines · Ondrej Zary
Hello,
I have an old ISA SCSI card that came with HP ScanJet IIP scanner. It's HP C2502 card based on NCR 53C400A chip. I was unable to get it working withg_NCR5380driver so I tried loading the official MINI400I.SYS driver in DOSemu. I was surprised that the values sent to the ports are not the same as in theg_NCR5380driver.
It should work in 2.4 providing you use the loading options for ncr53c400a and set a port and no IRQ (read mine did). What options are you trying ?
Quoted 4 lines
According to this, I think that my card has the 53C400A chip registers mapped to different addresses (offsets) but I'm unable to determine what the mapping is. I was also unable to find the 53C400A datasheet which might help a bit.
The 53c400a can be programming to an address by software - either by magic sequences or I believe according to pin strapping by ISAPnP. Its been a long time since I touched such junk however and if you want to do anything useful with your computer while scanning (like waving the mouse point around) get something else!
Quoted 9 lines · Alan Cox
Quoted 5 lines · Ondrej Zary
Hello,
I have an old ISA SCSI card that came with HP ScanJet IIP scanner. It's
HP C2502 card based on NCR 53C400A chip. I was unable to get it working
withg_NCR5380driver so I tried loading the official MINI400I.SYS
driver in DOSemu. I was surprised that the values sent to the ports are not the same as in theg_NCR5380driver.
Quoted 3 lines
It should work in 2.4 providing you use the loading options for ncr53c400a and set a port and no IRQ (read mine did). What options are you trying ?
I forgot to say that I'm trying this in 2.6.9. I've tried options like this:
ncr_53c400a=1 ncr_addr=0x350 ncr_irq=255
also tried ncr_53c400=1 (without the 'a'), various addresses and IRQs. It never worked. I always get "scsi0: bus busy, attempting abort", etc. and even Oops sometimes.
Quoted 5 lines
Quoted 1 line
According to this, I think that my card has the 53C400A chip registers mapped to different addresses (offsets) but I'm unable to determine what the mapping is. I was also unable to find the 53C400A datasheet which might help a bit.
The 53c400a can be programming to an address by software - either by magic sequences or I believe according to pin strapping by ISAPnP.
My card has no jumpers - only solder points for two 3-pin jumpers and it doesn't look like it can do ISAPnP.
I've made a simple test program in pascal to test the magic sequences in DOS. The card ignores the magic sequences that the g_NCR5380 driver uses. When I use the sequences obtained from MINI400I.SYS using DOSemu, it "works" - I can read/write the card's registers at the configured base address. The IRQ (2,3,4,5 and 7) can be configured by the magic sequence too (by setting the high-order bits in the last number in the sequence). So I know how to configure my card, maybe I should try to add it to the driver (e.g. by adding ncr_53c400a_hp=1 parameter). If I only could get the register mapping correctly (I think that this is the problem now).
The g_NCR5380 driver moves the base address by +8 bytes for 53C400 chips (but not for 53C400A) and defines the 53C400 specifis register offsets negative. This looks weird to me - either the 53C400A does not have these additional registers or the driver is broken and is trying to access these registers outside the I/O range on 53C400A.
Quoted 3 lines
Its been a long time since I touched such junk however and if you want to do anything useful with your computer while scanning (like waving the mouse point around) get something else!
I know it's old, cheap and bad - I just want to make it work. I remember that it worked in DOS/Windows 3.1. I was not successful in Windows 98 - although there is an official driver from HP.
P.S. I've removed the Ingmar Baumgart's e-mail address from CC as it does not work.
Signature · 1 line
Ondrej Zary
Quoted 5 lines · Ondrej Zary
I forgot to say that I'm trying this in 2.6.9. I've tried options like this:
ncr_53c400a=1 ncr_addr=0x350 ncr_irq=255
also tried ncr_53c400=1 (without the 'a'), various addresses and IRQs. It never worked. I always get "scsi0: bus busy, attempting abort", etc. and even Oops sometimes.
The driver hasn't been updated fully to 2.6 so thats not suprising (it ought to be marked && BROKEN I guess)