Skip to contentSkip to conversation

"irq 16: nobody cared!" -errors after motherboard-switch (ABIT IS7-E2 motherboard)

DISCUSSION K G 3 participants 5 messages Dec 1, 2004 – Dec 3, 2004

lore
Share & tools
lore

K G

author
#0 lore raw

Hello!

This is a part from /var/log/dmesg (link to full file included later):

irq 16: nobody cared!

 [<c0108366>] __report_bad_irq+0x2a/0x8b
 [<c0108450>] note_interrupt+0x6f/0x9f
 [<c010876e>] do_IRQ+0x161/0x192
 [<c0106a40>] common_interrupt+0x18/0x20
 [<c042ffd3>] cfb_imageblit+0x3b7/0x60c
 [<c0106a40>] common_interrupt+0x18/0x20
 [<c0426a37>] accel_putcs+0x29a/0x320
 [<c0108752>] do_IRQ+0x145/0x192
 [<c042007b>] cdrom_mrw_probe_pc+0xa5/0xa8
 [<c04280a2>] fbcon_redraw+0x1e8/0x208
 [<c042880a>] fbcon_scroll+0x748/0xc40
 [<c037cbb1>] scrup+0x13b/0x14f
 [<c037e5d7>] lf+0x73/0x75
 [<c0380e6c>] vt_console_print+0x127/0x2ed
 [<c0123a82>] __call_console_drivers+0x55/0x57
 [<c0123b90>] call_console_drivers+0x85/0x11f
 [<c0123f67>] release_console_sem+0x63/0xf3
 [<c0123e6b>] printk+0x169/0x1bd
 [<c075f834>] usb_pwc_init+0x43/0x3a7
 [<c07428e5>] do_initcalls+0x28/0xb4
 [<c0133ea4>] init_workqueues+0x17/0x2e
 [<c0100520>] init+0xf3/0x263
 [<c010042d>] init+0x0/0x263
 [<c0104271>] kernel_thread_helper+0x5/0xb

handlers:
[<c0435483>] (usb_hcd_irq+0x0/0x67)
[<c0435483>] (usb_hcd_irq+0x0/0x67)
Disabling IRQ #16

I've recently switched from an "ASUS P4T533-C" motherboard to an "ABIT IS7-E2", and got the errors mentioned above after boot. Only the motherboard and the ram was changed (rambus -> INFINEON 400Mhz DDR).

I've tried everything that I could do, bot non of them helped:

I've set the Sata to "enhanced mode" in BIOS Settings, which solved the problem for a guy with a similar ABIT motherboard, it didn't worked for me; Actually I've tried all Sata settings...

I've tried it with 2.6.7, 2.6.9, even 2.6.10-rc2 kernels, same error everywhere.

Slax LiveCD got the same error, my installed system got the same error(SourceMage linux). Interestingly UHU-Linux hasn't got any errors(maybe because the 2.4 kernel it uses).

So I've figured that the IRQ is shared between the two onboard 1.1 USB hubs and the vga card. My vga is an NVIDIA GeForce4 Ti4200 btw.

If I disable the onboard usb in the BIOS, I get no errors. I also don't get any errors when I pass the "noirqdebug" parameter to the kernel. (Maybe the system is a bit slower I think.)

If I get the errors I can't start X with the nvidia driver, and my usb mouse stops working. However if I use vesa for video I can start X, and it runs just fine. USB mouse works too, if I plug it elsewhere(not in the motherboard's onboard usb hubs)

I have support of ACPI support in kernel, tried to boot with "noacpi" parameter, but nothing changed. Disabling ACPI support in kernel give the same results.

Oh, and when I tried to install windows XP for my sis on the same computer it hangs after it copied the files to hdd, and rebooted the system. It stays there with the blue background of the installer and a cursor. Mouse moves, but nothing happens. I've just wrote this here to give all info I can. :)

So I only want to know that why can it work flawlessly with noirqdebug on, and why it can't without.

I've put the board in the computer according to its' manual, and it is ok I think. Though if I messed up something, then I REALLY don't want to waste your time, but if someone would be so kind to explain me in cc than I would be really thankful :) I don't want to waste your time or the list's bandwith.

Here are the complete logs/files:

http://izone.sytes.net/logs/dmesg
http://izone.sytes.net/logs/.config
http://izone.sytes.net/logs/xorg.log

Or the compressed version with all of them:
http://izone.sytes.net/logs/logs.tar.bz2

Kálmán Gergely

PS: This is a first post, so please be gentle :)

__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com

author
#1 lore raw
Quoted 119 lines · --- K G

Hello!

This is a part from /var/log/dmesg (link to full file
included later):

irq 16: nobody cared!

 [<c0108366>] __report_bad_irq+0x2a/0x8b
 [<c0108450>] note_interrupt+0x6f/0x9f
 [<c010876e>] do_IRQ+0x161/0x192
 [<c0106a40>] common_interrupt+0x18/0x20
 [<c042ffd3>] cfb_imageblit+0x3b7/0x60c
 [<c0106a40>] common_interrupt+0x18/0x20
 [<c0426a37>] accel_putcs+0x29a/0x320
 [<c0108752>] do_IRQ+0x145/0x192
 [<c042007b>] cdrom_mrw_probe_pc+0xa5/0xa8
 [<c04280a2>] fbcon_redraw+0x1e8/0x208
 [<c042880a>] fbcon_scroll+0x748/0xc40
 [<c037cbb1>] scrup+0x13b/0x14f
 [<c037e5d7>] lf+0x73/0x75
 [<c0380e6c>] vt_console_print+0x127/0x2ed
 [<c0123a82>] __call_console_drivers+0x55/0x57
 [<c0123b90>] call_console_drivers+0x85/0x11f
 [<c0123f67>] release_console_sem+0x63/0xf3
 [<c0123e6b>] printk+0x169/0x1bd
 [<c075f834>] usb_pwc_init+0x43/0x3a7
 [<c07428e5>] do_initcalls+0x28/0xb4
 [<c0133ea4>] init_workqueues+0x17/0x2e
 [<c0100520>] init+0xf3/0x263
 [<c010042d>] init+0x0/0x263
 [<c0104271>] kernel_thread_helper+0x5/0xb

handlers:
[<c0435483>] (usb_hcd_irq+0x0/0x67)
[<c0435483>] (usb_hcd_irq+0x0/0x67)
Disabling IRQ #16

I've recently switched from an "ASUS P4T533-C" motherboard to an "ABIT IS7-E2", and got the errors mentioned above after boot. Only the motherboard and the ram was changed (rambus -> INFINEON 400Mhz DDR).

I've tried everything that I could do, bot non of them
helped:

I've set the Sata to "enhanced mode" in BIOS Settings,
which solved the problem for a guy with a similar ABIT
motherboard, it didn't worked for me; Actually I've tried all Sata settings...

I've tried it with 2.6.7, 2.6.9, even 2.6.10-rc2 kernels, same error everywhere.

Slax LiveCD got the same error, my installed system got the same error(SourceMage linux). Interestingly UHU-Linux hasn't got any errors(maybe because the 2.4
kernel it uses).

So I've figured that the IRQ is shared between the two
onboard 1.1 USB hubs and the vga card. My vga is an NVIDIA GeForce4 Ti4200 btw.

If I disable the onboard usb in the BIOS, I get no errors. I also don't get any errors when I pass the "noirqdebug" parameter to the kernel. (Maybe the system is a bit slower I think.)

If I get the errors I can't start X with the nvidia driver, and my usb mouse stops working. However if I use vesa for video I can start X, and it runs just fine. USB mouse works too, if I plug it elsewhere(not
in the motherboard's onboard usb hubs)

I have support of ACPI support in kernel, tried to boot with "noacpi" parameter, but nothing changed. Disabling ACPI support in kernel give the same results.

Oh, and when I tried to install windows XP for my sis
on the same computer it hangs after it copied the files to hdd, and rebooted the system. It stays there
with the blue background of the installer and a cursor. Mouse moves, but nothing happens. I've just wrote this here to give all info I can. :)

So I only want to know that why can it work flawlessly
with noirqdebug on, and why it can't without.

I've put the board in the computer according to its' manual, and it is ok I think. Though if I messed up something, then I REALLY don't want to waste your time, but if someone would be so kind to explain me in
cc than I would be really thankful :) I don't want to
waste your time or the list's bandwith.

Here are the complete logs/files:

http://izone.sytes.net/logs/dmesg
http://izone.sytes.net/logs/.config
http://izone.sytes.net/logs/xorg.log

Or the compressed version with all of them:
http://izone.sytes.net/logs/logs.tar.bz2

Kálmán Gergely

PS: This is a first post, so please be gentle :)

Quoted 13 lines

__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com
-
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
the body of a message to [email protected] More majordomo info at
http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/

This post was done by me, but the Hungarian characters in my name caused the list to show only the first K :) I just don't wanted to be rude not to introduce myself

Kalman Gergely

__________________________________________________
Do You Yahoo!?
Tired of spam? Yahoo! Mail has the best spam protection around
http://mail.yahoo.com

#2 lore raw
In reply to K G
Quoted 4 lines · K G

I've recently switched from an "ASUS P4T533-C" motherboard to an "ABIT IS7-E2", and got the errors mentioned above after boot. Only the motherboard and the ram was changed (rambus -> INFINEON 400Mhz DDR).

Those generally indicate bad interrupt routing but could given the other information you provide just indicate a dud board.

Quoted 2 lines

got the same error(SourceMage linux). Interestingly UHU-Linux hasn't got any errors(maybe because the 2.4

kernel it uses).

Try booting with the option "acpi=off"

Quoted 3 lines

So I've figured that the IRQ is shared between the two onboard 1.1 USB hubs and the vga card. My vga is an NVIDIA GeForce4 Ti4200 btw.

Thats fine in itself well assuming the Nvidia driver is being polite which I would imagine it is. Its binary only so we can only hope not check.

Quoted 3 lines

Oh, and when I tried to install windows XP for my sis on the same computer it hangs after it copied the files to hdd, and rebooted the system. It stays there

Sounds like a dud board then ? We see a lot of broken interrupt routing reports but they usually work on Windows XP by chance and that was all the vendor tested.

#3 lore raw
Quoted 8 lines · Alan Cox
Quoted 4 lines · K G

I've recently switched from an "ASUS P4T533-C" motherboard to an "ABIT IS7-E2", and got the errors mentioned above after boot. Only the motherboard and the ram was changed (rambus -> INFINEON 400Mhz DDR).

Those generally indicate bad interrupt routing but could given the other information you provide just indicate a dud board.

Agreed, though it's also on occasion drivers that need to ack/silence interrupts during initialization.

Jeff