Skip to contentSkip to conversation

Microsoft Bluethooth "Elite" Keyboard & Mouse

Bluez-users Francesco Bochicchio 3 participants 9 messages Jan 16, 2005 – Jan 20, 2005 Bluetooth drivers

lore
Share & tools
lore
#0 lore raw

Hi all,

I have a Microsft Bluetooth "Elite" keyboard and optical mouse, and I'm trying to make it work with Linux.

I have googled and read stuff, but currently I'm stucked.

When I plug the USB Dongle in an USB port I get the following kernel messages (among others):

Jan 15 13:48:22 superlap kernel: usb 1-2.2: new full speed USB device using address 8
Jan 15 13:48:23 superlap kernel: input: USB HID v1.11 Keyboard [045e:00bf] on usb-0000:00:10.0-2.2
Jan 15 13:48:24 superlap kernel: usb 1-2.3: new full speed USB device using address 9
Jan 15 13:48:25 superlap kernel: input: USB HID v1.11 Mouse [045e:00be] on usb-0000:00:10.0-2.3

Also, hotplug loads a bunch of modules, including :

usbmouse
joydev
usbkbd
usbhid
hci_usb
rfcomm
l2cap
bluetooth

Finally, I get the message:

Jan 15 13:48:31 superlap hcid[2744]: Can't init device hci0. Connection timed out(110) 

The device hci0 is created but not opeerative:

superlap:/home/fb# hciconfig 
hci0:   Type: USB
        BD Address: 00:00:00:00:00:00 ACL MTU: 0:0  SCO MTU: 0:0
        DOWN 
        RX bytes:0 acl:0 sco:0 events:0 errors:0
        TX bytes:3 acl:0 sco:0 commands:1 errors:0

and if I try to bring it up:

superlap:/home/fb# hciconfig hci0 up
Can't init device hci0. Connection timed out(110)

I also tried hcidump, but it hangs after this output:

superlap:/home/fb# hcidump -x
HCIDump - HCI packet analyzer ver 1.12
device: hci0 snap_len: 1028 filter: 0xffffffff

I tried all this with and without batteries inserted (no change). I also tried pressing the litte button on the back while doing "hciconfig hci0 up" and pressing keys while doing "hcidump -x".

The keyboard and mouse works with Windows XP SP2, so the problem is not the hardware.

My questions:

1. Does this device works with Linux+blueZ ? (I know that someone had success with other models of MS BT keyboards).

2. Do I have to patch the kernel? (actually I have a Kernel 2.6.9 pre-compiled (Debian Unstable distro) for AMD k7).

3. What else can I try?

Thanks for any hint.

Ciao
----
FB

-------------------------------------------------------
The SF.Net email is sponsored by: Beat the post-holiday blues Get a FREE limited edition SourceForge.net t-shirt from ThinkGeek. It's fun and FREE -- well, almost....http://www.thinkgeek.com/sfshirt
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users

#1 lore raw

Hi,

You should use 2.6.10-mh1 and latest firmware for Digianswer dongle (adapter use it I think)

Michal

Dne ne 16. ledna 2005 18:46 Francesco Bochicchio napsal(a):

Quoted 90 lines

Hi all,

I have a Microsft Bluetooth "Elite" keyboard and optical mouse, and I'm trying to make it work with Linux.

I have googled and read stuff, but currently I'm stucked.

When I plug the USB Dongle in an USB port I get the following kernel messages (among others):

Jan 15 13:48:22 superlap kernel: usb 1-2.2: new full speed USB device using

address 8 Jan 15 13:48:23 superlap kernel: input: USB HID v1.11 Keyboard [045e:00bf] on usb-0000:00:10.0-2.2 Jan 15 13:48:24 superlap kernel: usb 1-2.3: new full speed USB device using address 9 Jan 15 13:48:25 superlap
kernel: input: USB HID v1.11 Mouse [045e:00be] on usb-0000:00:10.0-2.3

Also, hotplug loads a bunch of modules, including :

usbmouse
joydev
usbkbd
usbhid
hci_usb
rfcomm
l2cap
bluetooth

Finally, I get the message:

Jan 15 13:48:31 superlap hcid[2744]: Can't init device hci0. Connection

timed out(110)

The device hci0 is created but not opeerative:

superlap:/home/fb# hciconfig
hci0:   Type: USB
        BD Address: 00:00:00:00:00:00 ACL MTU: 0:0  SCO MTU: 0:0
        DOWN
        RX bytes:0 acl:0 sco:0 events:0 errors:0
        TX bytes:3 acl:0 sco:0 commands:1 errors:0

and if I try to bring it up:

superlap:/home/fb# hciconfig hci0 up
Can't init device hci0. Connection timed out(110)

I also tried hcidump, but it hangs after this output:

superlap:/home/fb# hcidump -x
HCIDump - HCI packet analyzer ver 1.12
device: hci0 snap_len: 1028 filter: 0xffffffff

I tried all this with and without batteries inserted (no change). I also tried pressing the litte button on the back while doing "hciconfig hci0 up" and pressing keys while doing "hcidump -x".

The keyboard and mouse works with Windows XP SP2, so the problem is not the hardware.

My questions:

1. Does this device works with Linux+blueZ ? (I know that someone had success with other models of MS BT keyboards).

2. Do I have to patch the kernel? (actually I have a Kernel 2.6.9 pre-compiled (Debian Unstable distro) for AMD k7).

3. What else can I try?

Thanks for any hint.

Ciao
----
FB

-------------------------------------------------------
The SF.Net email is sponsored by: Beat the post-holiday blues Get a FREE limited edition SourceForge.net t-shirt from ThinkGeek. It's fun and FREE -- well, almost....http://www.thinkgeek.com/sfshirt
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users

Signature · 13 lines
S pozdravem

Michal Semler


-------------------------------------------------------
The SF.Net email is sponsored by: Beat the post-holiday blues
Get a FREE limited edition SourceForge.net t-shirt from ThinkGeek.
It's fun and FREE -- well, almost....http://www.thinkgeek.com/sfshirt
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users
maintainer
#2 lore raw

Hi Michal,

Quoted 2 lines

You should use 2.6.10-mh1 and latest firmware for Digianswer dongle (adapter use it I think)

using the 2.6.10-mh1 is a good idea, but it is a Broadcom dongle with HID proxy and this don't need any extra firmware. However since the other Broadcom HID proxy that I have does the switch into HCI mode when you send a HCI_Reset (CSR HID Proxy needs an extra tool btw), the one from Microsoft may need some extra magic to fully work without problems. I need someone to donate one of these, because there is no way to buy only the dongle and I am not going to buy another Bluetooth keyboard. I have enough.

Regards

Marcel

-------------------------------------------------------
The SF.Net email is sponsored by: Beat the post-holiday blues Get a FREE limited edition SourceForge.net t-shirt from ThinkGeek. It's fun and FREE -- well, almost....http://www.thinkgeek.com/sfshirt
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users

#3 lore raw

So Francesco send your dongle to Marcel for a while and he will fix it :)

Michal

Dne ne 16. ledna 2005 19:01 Marcel Holtmann napsal(a):

Quoted 29 lines

Hi Michal,

Quoted 2 lines

You should use 2.6.10-mh1 and latest firmware for Digianswer dongle (adapter use it I think)

using the 2.6.10-mh1 is a good idea, but it is a Broadcom dongle with HID proxy and this don't need any extra firmware. However since the other Broadcom HID proxy that I have does the switch into HCI mode when you send a HCI_Reset (CSR HID Proxy needs an extra tool btw), the one from Microsoft may need some extra magic to fully work without problems. I need someone to donate one of these, because there is no way to buy only the dongle and I am not going to buy another Bluetooth keyboard. I have enough.

Regards

Marcel

-------------------------------------------------------
The SF.Net email is sponsored by: Beat the post-holiday blues Get a FREE limited edition SourceForge.net t-shirt from ThinkGeek. It's fun and FREE -- well, almost....http://www.thinkgeek.com/sfshirt
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users

Signature · 13 lines
S pozdravem

Michal Semler


-------------------------------------------------------
The SF.Net email is sponsored by: Beat the post-holiday blues
Get a FREE limited edition SourceForge.net t-shirt from ThinkGeek.
It's fun and FREE -- well, almost....http://www.thinkgeek.com/sfshirt
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users
#4 lore raw
In reply to Marcel Holtmann
Quoted 10 lines · Marcel Holtmann

Hi Michal,

Quoted 2 lines

You should use 2.6.10-mh1 and latest firmware for Digianswer dongle (adapter use it I think)

using the 2.6.10-mh1 is a good idea, but it is a Broadcom dongle with HID proxy and this don't need any extra firmware. However since the other Broadcom HID proxy that I have does the switch into HCI mode when you send a HCI_Reset (CSR HID Proxy needs an extra tool btw), the one from Microsoft may need some extra magic to fully work without problems.

Ok. Thanks. I will try out 2.6.10-mh1 anyway.

BTW, just out of curiosity: would the MS Keyboard works with another Bluetooth USB dongle?

Quoted 4 lines

I need someone to donate one of these, because there is no way to buy only the dongle and I am not going to buy another Bluetooth keyboard. I have enough.

I could consider swapping mine with one that already works with Linux :-)

Ciao
-----
FB

-------------------------------------------------------
The SF.Net email is sponsored by: Beat the post-holiday blues Get a FREE limited edition SourceForge.net t-shirt from ThinkGeek. It's fun and FREE -- well, almost....http://www.thinkgeek.com/sfshirt
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users

#5 lore raw

Dne ne 16. ledna 2005 20:37 Francesco Bochicchio napsal(a):

Quoted 12 lines · Marcel Holtmann
Quoted 10 lines

Hi Michal,

Quoted 2 lines

You should use 2.6.10-mh1 and latest firmware for Digianswer dongle (adapter use it I think)

using the 2.6.10-mh1 is a good idea, but it is a Broadcom dongle with HID proxy and this don't need any extra firmware. However since the other Broadcom HID proxy that I have does the switch into HCI mode when you send a HCI_Reset (CSR HID Proxy needs an extra tool btw), the one from Microsoft may need some extra magic to fully work without problems.

Quoted 5 lines

Ok. Thanks. I will try out 2.6.10-mh1 anyway.

BTW, just out of curiosity: would the MS Keyboard works with another Bluetooth USB dongle?

YES, You should prefer CSR based dongles!

Quoted 21 lines
Quoted 4 lines

I need someone to donate one of these, because there is no way to buy only the dongle and I am not going to buy another Bluetooth keyboard. I have enough.

I could consider swapping mine with one that already works with Linux :-)

Ciao
-----
FB

-------------------------------------------------------
The SF.Net email is sponsored by: Beat the post-holiday blues Get a FREE limited edition SourceForge.net t-shirt from ThinkGeek. It's fun and FREE -- well, almost....http://www.thinkgeek.com/sfshirt
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users

Signature · 13 lines
S pozdravem

Michal Semler


-------------------------------------------------------
The SF.Net email is sponsored by: Beat the post-holiday blues
Get a FREE limited edition SourceForge.net t-shirt from ThinkGeek.
It's fun and FREE -- well, almost....http://www.thinkgeek.com/sfshirt
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users
maintainer
#6 lore raw
In reply to Francesco Bochicchio

Hi Francesco,

Quoted 1 line

BTW, just out of curiosity: would the MS Keyboard works with another Bluetooth USB dongle?

you can use any dongle you like. And as Michal said, you should prefer a CSR one with at least HCI 16.4 firmware. Will make your life a lot more easier.

Quoted 5 lines
Quoted 3 lines

I need someone to donate one of these, because there is no way to buy only the dongle and I am not going to buy another Bluetooth keyboard. I have enough.

I could consider swapping mine with one that already works with Linux :-)

I have a lot of dongles at home, but I can't give any of them away. I need them for testing when I change specific stuff.

Regards

Marcel

-------------------------------------------------------
The SF.Net email is sponsored by: Beat the post-holiday blues Get a FREE limited edition SourceForge.net t-shirt from ThinkGeek. It's fun and FREE -- well, almost....http://www.thinkgeek.com/sfshirt
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users

#7 lore raw

Re: [Bluez-users] Microsoft Bluethooth "Elite" Keyboard & Mouse - UPDATE: works with stock 2.6.10

In reply to Francesco Bochicchio
Quoted 6 lines · Francesco Bochicchio
Quoted 5 lines · Marcel Holtmann

Hi Michal,

Quoted 2 lines

You should use 2.6.10-mh1 and latest firmware for Digianswer dongle (adapter use it I think)

Quoted 9 lines
Quoted 5 lines

using the 2.6.10-mh1 is a good idea, but it is a Broadcom dongle with HID proxy and this don't need any extra firmware. However since the other Broadcom HID proxy that I have does the switch into HCI mode when you send a HCI_Reset (CSR HID Proxy needs an extra tool btw), the one from Microsoft may need some extra magic to fully work without problems.

Ok. Thanks. I will try out 2.6.10-mh1 anyway.

Hi all,

just un update for the records.

I tried with plain 2.6.10 (from debian kernel-source package, without any patch other than Debian's) and it seems to work fine with my BT keyboard & mouse. Only needed an "hidd --connect" after inserting the dongle (the one coming with the keyboard).
It might be that in the future I will experience the problems hinted by Marcel, but for now I am happy :-).

I'm trying now to make the dongle work with my SonyEricsson T610; for now the phone it is discovered (and is capable to discover the PC), but I'm not yet succeeded to use OpenObex tools with the bluetooth connection. But that is another story.

Question: what would be the advantage now of applying the 2.6.10-mh1 patch to sthe standard kernel sources?

Ciao
-----
FB

-------------------------------------------------------
This SF.Net email is sponsored by: IntelliVIEW -- Interactive Reporting Tool for open source databases. Create drag-&-drop reports. Save time by over 75%! Publish reports on the web. Export to DOC, XLS, RTF, etc. Download a FREE copy at http://www.intelliview.com/go/osdn_nl
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users

maintainer
#8 lore raw

Re: [Bluez-users] Microsoft Bluethooth "Elite" Keyboard & Mouse - UPDATE: works with stock 2.6.10

Hi Francesco,

Quoted 7 lines

I tried with plain 2.6.10 (from debian kernel-source package, without any patch other than Debian's) and it seems to work fine with my BT keyboard & mouse. Only needed an "hidd --connect" after inserting the dongle (the one coming with the keyboard).
It might be that in the future I will experience the problems hinted by Marcel, but for now I am happy :-).

Quoted 7 lines

I'm trying now to make the dongle work with my SonyEricsson T610; for now the phone it is discovered (and is capable to discover the PC), but I'm not yet succeeded to use OpenObex tools with the bluetooth connection. But that is another story.

Question: what would be the advantage now of applying the 2.6.10-mh1 patch to sthe standard kernel sources?

you will get the latest Bluetooth subsystem that also includes some changes to the hidp kernel module.

Regards

Marcel

-------------------------------------------------------
This SF.Net email is sponsored by: IntelliVIEW -- Interactive Reporting Tool for open source databases. Create drag-&-drop reports. Save time by over 75%! Publish reports on the web. Export to DOC, XLS, RTF, etc. Download a FREE copy at http://www.intelliview.com/go/osdn_nl
_______________________________________________
Bluez-users mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/bluez-users