RFC: use datacs is smc91x driver
Hi Nico,
Below is a first cut at supporting the second 32-bit DATACS chipselect in the smc91x driver to transfer data.
My platform has a 16-bit chip select for the primary IO region and no DMA. I found that throughput went from roughly 50mbit/s to 80mbit/s. I tested by throwing UDP packets at it using mgen (9000 packets/second with UDP payload of 1472 bytes is roughly 100mbit/s, I think) and counting the packets received in 60s, I then did the same for transmitting. The measurements are very rough but the improvement seems fairly significant to me. Perhaps there is another benchmark you would like me to try?
I did consider adding a define for 'NEEDS_ATTRIB_ENABLE' but decided not to in the end for backwards compat, and because I have no platforms to test that bit on. That is why the attrib stuff has been factored out of smc_probe(), I think it is tidier that way anyway.
I'm not entirely happy with using the SMC_*_RESOURCE defines to find the correct resources, but I don't think you can have a placeholder for the attrib space at index 1 (when you don't have an attrib space) and still have datacs at index 2.
What do you think?
Ian.
drivers/net/smc91x.c +115 -42
@@ -201,6 +201,10 @@spinlock_t lock; +#ifdef SMC_CAN_USE_DATACS +u32 *datacs; +#endif +#ifdef SMC_USE_PXA_DMA /* DMA needs the physical address of the chip */ u_long physaddr;
@@ -1989,16 +1993,21 @@return retval; } -static int smc_enable_device (unsigned long attrib_phys) +static int smc_enable_device (struct platform_device *pdev) {unsigned long flags;unsigned char ecor, ecsr;void *addr; +struct resource * res; + + res =platform_get_resource (pdev,IORESOURCE_MEM ,SMC_ATTRIB_RESOURCE ); +if (!res) +return 0 ;/* * Map the attribute space. This is overkill, but clean. */ - addr =ioremap (attrib_phys,ATTRIB_SIZE ); + addr =ioremap (res->start,ATTRIB_SIZE );if (!addr)return -ENOMEM ;
@@ -2046,6 +2055,72 @@return 0 ; } +static int smc_request_attrib (struct platform_device *pdev) +{ +struct resource * res =platform_get_resource (pdev,IORESOURCE_MEM ,SMC_ATTRIB_RESOURCE ); + +if (res) { +if (!request_mem_region (res->start,ATTRIB_SIZE ,CARDNAME )) +return -EBUSY ; + } +return 0 ; +} + +static void smc_release_attrib (struct platform_device *pdev) +{ +struct resource * res =platform_get_resource (pdev,IORESOURCE_MEM ,SMC_ATTRIB_RESOURCE ); + +if (res) +release_mem_region (res->start,ATTRIB_SIZE ); +} + +#ifdef SMC_CAN_USE_DATACS +static void smc_request_datacs (struct platform_device *pdev,struct net_device *ndev) +{ +struct resource * res =platform_get_resource (pdev,IORESOURCE_MEM ,SMC_DATACS_RESOURCE ); +struct smc_local *lp =netdev_priv (ndev); + +if (!res) { +printk (KERN_CRIT "no datacs resource\n" ); +return ; + } + +if (!request_mem_region (res->start,SMC_DATA_EXTENT ,CARDNAME )) { +printk (KERN_CRIT "failed request region\n" ); +return ; + } + +printk (KERN_CRIT "%s: requested datacs memory region %#010lx-%#010lx\n" , +CARDNAME , res->start, res->end); + + lp->datacs =ioremap (res->start,SMC_DATA_EXTENT ); +printk (KERN_CRIT "%s: remapped datacs to %p\n" ,CARDNAME , lp->datacs); + +} + +static void smc_release_datacs (struct platform_device *pdev,struct net_device *ndev) +{ +struct smc_local *lp =netdev_priv (ndev); +struct resource * res =platform_get_resource (pdev,IORESOURCE_MEM ,SMC_DATACS_RESOURCE ); + +if (lp->datacs) { +printk (KERN_CRIT "%s: releasing datacs at %p\n" ,CARDNAME , lp->datacs); +iounmap (lp->datacs); + } + + lp->datacs =NULL ; + +if (res) { +release_mem_region (res->start,SMC_DATA_EXTENT ); +printk (KERN_CRIT "%s: released datacs memory region %#010lx-%#010lx\n" , +CARDNAME , res->start, res->end); + } +} +#else +static void smc_request_datacs (struct platform_device *pdev,struct net_device *ndev) {} +static void smc_release_datacs (struct platform_device *pdev,struct net_device *ndev) {} +#endif +/* * smc_init(void) * Input parameters:
@@ -2061,20 +2136,18 @@ {struct platform_device *pdev =to_platform_device (dev);struct net_device *ndev; -struct resource *res, *ext =NULL ; +struct resource *res;unsigned int *addr;int ret; - res =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); + res =platform_get_resource (pdev,IORESOURCE_MEM ,SMC_IO_RESOURCE );if (!res) { ret = -ENODEV ; goto out; } -/* -* Request the regions. -*/ -if (!request_mem_region (res->start,SMC_IO_EXTENT ,"smc91x" )) { + +if (!request_mem_region (res->start,SMC_IO_EXTENT ,CARDNAME )) { ret = -EBUSY ; goto out; }
@@ -2083,7 +2156,7 @@if (!ndev) {printk ("%s: could not allocate device.\n" ,CARDNAME ); ret = -ENOMEM ; - goto release_1; + goto out_release_io; }SET_MODULE_OWNER (ndev);SET_NETDEV_DEV (ndev, dev);
@@ -2091,42 +2164,27 @@ ndev->dma = (unsigned char )-1 ; ndev->irq =platform_get_irq (pdev,0 ); - ext =platform_get_resource (pdev,IORESOURCE_MEM ,1 ); -if (ext) { -if (!request_mem_region (ext->start,ATTRIB_SIZE , ndev->name)) { - ret = -EBUSY ; - goto release_1; - } - + ret =smc_request_attrib (pdev); +if (ret) + goto out_free_netdev;#if defined(CONFIG_SA1100_ASSABET ) -NCR_0 |=NCR_ENET_OSC_EN ; +NCR_0 |=NCR_ENET_OSC_EN ;#endif - - ret =smc_enable_device (ext->start); -if (ret) - goto release_both; - } + ret =smc_enable_device (pdev); +if (ret) + goto out_release_attrib; addr =ioremap (res->start,SMC_IO_EXTENT );if (!addr) { ret = -ENOMEM ; - goto release_both; + goto out_release_attrib; } +printk (KERN_CRIT "%s: mapped IO to %p\n" ,CARDNAME , addr);dev_set_drvdata (dev, ndev); ret =smc_probe (ndev, (unsigned long )addr); -if (ret !=0 ) { -dev_set_drvdata (dev,NULL ); -iounmap (addr); - release_both: -if (ext) -release_mem_region (ext->start,ATTRIB_SIZE ); -free_netdev (ndev); - release_1: -release_mem_region (res->start,SMC_IO_EXTENT ); - out: -printk ("%s: not found (%d).\n" ,CARDNAME , ret); - } +if (ret !=0 ) + goto out_iounmap;#ifdef SMC_USE_PXA_DMA else {struct smc_local *lp =netdev_priv (ndev);
@@ -2134,6 +2192,22 @@ }#endif +smc_request_datacs (pdev, ndev); + +return 0 ; + + out_iounmap: +dev_set_drvdata (dev,NULL ); +iounmap (addr); + out_release_attrib: +smc_release_attrib (pdev); + out_free_netdev: +free_netdev (ndev); + out_release_io: +release_mem_region (res->start,SMC_IO_EXTENT ); + out: +printk ("%s: not found (%d).\n" ,CARDNAME , ret); +return ret; }
@@ -2154,10 +2228,11 @@pxa_free_dma (ndev->dma);#endif iounmap ((void *)ndev->base_addr); - res =platform_get_resource (pdev,IORESOURCE_MEM ,1 ); -if (res) -release_mem_region (res->start,ATTRIB_SIZE ); - res =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); + +smc_release_datacs (pdev,ndev); +smc_release_attrib (pdev); + + res =platform_get_resource (pdev,IORESOURCE_MEM ,SMC_IO_RESOURCE );release_mem_region (res->start,SMC_IO_EXTENT );free_netdev (ndev);
@@ -2186,9 +2261,7 @@if (ndev && level ==RESUME_ENABLE ) {struct smc_local *lp =netdev_priv (ndev); - -if (pdev->num_resources ==3 ) -smc_enable_device (pdev->resource[2 ].start); +smc_enable_device (pdev);if (netif_running (ndev)) {smc_reset (ndev);smc_enable (ndev);
drivers/net/smc91x.h +60 -6
98 lines not on this page · raw message
Signature · 10 lines
Ian Campbell, Senior Design Engineer
Web: http://www.arcom.com
Arcom, Clifton Road, Direct: +44 (0)1223 403 465
Cambridge CB1 7EA, United Kingdom Phone: +44 (0)1223 411 200
_____________________________________________________________________
The message in this transmission is sent in confidence for the attention of the addressee only and should not be disclosed to any other party. Unauthorised recipients are requested to preserve this confidentiality. Please advise the sender if the addressee is not resident at the receiving end. Email to and from Arcom is automatically monitored for operational and lawful business reasons.
This message has been virus scanned by MessageLabs.Quoted 4 lines · Ian Campbell
Hi Nico,
Below is a first cut at supporting the second 32-bit DATACS chipselect in the smc91x driver to transfer data.
[...]
Quoted 4 lines
I'm not entirely happy with using the SMC_*_RESOURCE defines to find the correct resources, but I don't think you can have a placeholder for the attrib space at index 1 (when you don't have an attrib space) and still have datacs at index 2.
I don't like that either. Maybe the whole thing should be converted to use platform_get_resource_byname() ?
Nicolas
Quoted 8 lines · Nicolas Pitre
Quoted 4 lines · Ian Campbell
I'm not entirely happy with using the SMC_*_RESOURCE defines to find the correct resources, but I don't think you can have a placeholder for the attrib space at index 1 (when you don't have an attrib space) and still have datacs at index 2.
I don't like that either. Maybe the whole thing should be converted to use
platform_get_resource_byname()?
Ah, I hadn't seen this new function, it looks ideal. I'll work up another that uses it and updates all the in tree drivers.
Are you happy with "iocs", "attrib" and "datacs" for the names?
Ian.
Signature · 10 lines
Ian Campbell, Senior Design Engineer
Web: http://www.arcom.com
Arcom, Clifton Road, Direct: +44 (0)1223 403 465
Cambridge CB1 7EA, United Kingdom Phone: +44 (0)1223 411 200
_____________________________________________________________________
The message in this transmission is sent in confidence for the attention of the addressee only and should not be disclosed to any other party. Unauthorised recipients are requested to preserve this confidentiality. Please advise the sender if the addressee is not resident at the receiving end. Email to and from Arcom is automatically monitored for operational and lawful business reasons.
This message has been virus scanned by MessageLabs.Quoted 1 line · Ian Campbell
Are you happy with "iocs", "attrib" and "datacs" for the names?
Of the platforms with an smc91x platform_device (according to grep) only 2 (lubbock, neponset) out of the 18 have memory resources other than the iocs (full list of platforms is at the end, after the patch)
So for the sake of the least intrusive patch I think for the main iocs I'll call _byname and fallback on mem resource number 0 if no named iocs resource exists. attrib and datacs must be explicitly named. This allows most of the board ports to remain unchanged.
I also noticed that the name propagates into /proc/iomem etc
# cat /proc/iomem [...] 10000000-10000003 : datacs 10000000-10000003 : smc91x so perhaps smc91x-datacs -attrib -iocs might be more appropriate names? I don't know if there is a policy about such things.
drivers/net/smc91x.c +108 -42
@@ -210,6 +210,10 @@spinlock_t lock; +#ifdef SMC_CAN_USE_DATACS +u32 *datacs; +#endif +#ifdef SMC_USE_PXA_DMA /* DMA needs the physical address of the chip */ u_long physaddr;
@@ -1998,16 +2002,21 @@return retval; } -static int smc_enable_device (unsigned long attrib_phys) +static int smc_enable_device (struct platform_device *pdev) {unsigned long flags;unsigned char ecor, ecsr;void *addr; +struct resource * res; + + res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"attrib" ); +if (!res) +return 0 ;/* * Map the attribute space. This is overkill, but clean. */ - addr =ioremap (attrib_phys,ATTRIB_SIZE ); + addr =ioremap (res->start,ATTRIB_SIZE );if (!addr)return -ENOMEM ;
@@ -2055,6 +2064,62 @@return 0 ; } +static int smc_request_attrib (struct platform_device *pdev) +{ +struct resource * res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"attrib" ); + +if (!res) +return 0 ; + +if (!request_mem_region (res->start,ATTRIB_SIZE ,CARDNAME )) +return -EBUSY ; + +return 0 ; +} + +static void smc_release_attrib (struct platform_device *pdev) +{ +struct resource * res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"attrib" ); + +if (res) +release_mem_region (res->start,ATTRIB_SIZE ); +} + +#ifdef SMC_CAN_USE_DATACS +static void smc_request_datacs (struct platform_device *pdev,struct net_device *ndev) +{ +struct resource * res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"datacs" ); +struct smc_local *lp =netdev_priv (ndev); + +if (!res) +return ; + +if (!request_mem_region (res->start,SMC_DATA_EXTENT ,CARDNAME )) { +printk (KERN_INFO "%s: failed to request datacs memory region.\n" ,CARDNAME ); +return ; + } + + lp->datacs =ioremap (res->start,SMC_DATA_EXTENT ); +} + +static void smc_release_datacs (struct platform_device *pdev,struct net_device *ndev) +{ +struct smc_local *lp =netdev_priv (ndev); +struct resource * res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"datacs" ); + +if (lp->datacs) +iounmap (lp->datacs); + + lp->datacs =NULL ; + +if (res) +release_mem_region (res->start,SMC_DATA_EXTENT ); +} +#else +static void smc_request_datacs (struct platform_device *pdev,struct net_device *ndev) {} +static void smc_release_datacs (struct platform_device *pdev,struct net_device *ndev) {} +#endif +/* * smc_init(void) * Input parameters:
@@ -2070,20 +2135,20 @@ {struct platform_device *pdev =to_platform_device (dev);struct net_device *ndev; -struct resource *res, *ext =NULL ; +struct resource *res;unsigned int *addr;int ret; - res =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); + res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"iocs" ); +if (!res) + res =platform_get_resource (pdev,IORESOURCE_MEM ,0 );if (!res) { ret = -ENODEV ; goto out; } -/* -* Request the regions. -*/ -if (!request_mem_region (res->start,SMC_IO_EXTENT ,"smc91x" )) { + +if (!request_mem_region (res->start,SMC_IO_EXTENT ,CARDNAME )) { ret = -EBUSY ; goto out; }
@@ -2092,7 +2157,7 @@if (!ndev) {printk ("%s: could not allocate device.\n" ,CARDNAME ); ret = -ENOMEM ; - goto release_1; + goto out_release_io; }SET_MODULE_OWNER (ndev);SET_NETDEV_DEV (ndev, dev);
@@ -2100,42 +2165,26 @@ ndev->dma = (unsigned char )-1 ; ndev->irq =platform_get_irq (pdev,0 ); - ext =platform_get_resource (pdev,IORESOURCE_MEM ,1 ); -if (ext) { -if (!request_mem_region (ext->start,ATTRIB_SIZE , ndev->name)) { - ret = -EBUSY ; - goto release_1; - } - + ret =smc_request_attrib (pdev); +if (ret) + goto out_free_netdev;#if defined(CONFIG_SA1100_ASSABET ) -NCR_0 |=NCR_ENET_OSC_EN ; +NCR_0 |=NCR_ENET_OSC_EN ;#endif - - ret =smc_enable_device (ext->start); -if (ret) - goto release_both; - } + ret =smc_enable_device (pdev); +if (ret) + goto out_release_attrib; addr =ioremap (res->start,SMC_IO_EXTENT );if (!addr) { ret = -ENOMEM ; - goto release_both; + goto out_release_attrib; }dev_set_drvdata (dev, ndev); ret =smc_probe (ndev, (unsigned long )addr); -if (ret !=0 ) { -dev_set_drvdata (dev,NULL ); -iounmap (addr); - release_both: -if (ext) -release_mem_region (ext->start,ATTRIB_SIZE ); -free_netdev (ndev); - release_1: -release_mem_region (res->start,SMC_IO_EXTENT ); - out: -printk ("%s: not found (%d).\n" ,CARDNAME , ret); - } +if (ret !=0 ) + goto out_iounmap;#ifdef SMC_USE_PXA_DMA else {struct smc_local *lp =netdev_priv (ndev);
@@ -2143,6 +2192,22 @@ }#endif +smc_request_datacs (pdev, ndev); + +return 0 ; + + out_iounmap: +dev_set_drvdata (dev,NULL ); +iounmap (addr); + out_release_attrib: +smc_release_attrib (pdev); + out_free_netdev: +free_netdev (ndev); + out_release_io: +release_mem_region (res->start,SMC_IO_EXTENT ); + out: +printk ("%s: not found (%d).\n" ,CARDNAME , ret); +return ret; }
@@ -2163,10 +2228,13 @@pxa_free_dma (ndev->dma);#endif iounmap ((void *)ndev->base_addr); - res =platform_get_resource (pdev,IORESOURCE_MEM ,1 ); -if (res) -release_mem_region (res->start,ATTRIB_SIZE ); - res =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); + +smc_release_datacs (pdev,ndev); +smc_release_attrib (pdev); + + res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"iocs" ); +if (!res) +platform_get_resource (pdev,IORESOURCE_MEM ,0 );release_mem_region (res->start,SMC_IO_EXTENT );free_netdev (ndev);
@@ -2195,9 +2263,7 @@if (ndev && level ==RESUME_ENABLE ) {struct smc_local *lp =netdev_priv (ndev); - -if (pdev->num_resources ==3 ) -smc_enable_device (pdev->resource[2 ].start); +smc_enable_device (pdev);if (netif_running (ndev)) {smc_reset (ndev);smc_enable (ndev);
drivers/net/smc91x.h +52 -7
90 lines not on this page · raw message
arch/arm/mach-sa1100/neponset.c +2 -0
@@ -266,6 +266,7 @@static struct resource smc91x_resources[] = { [0 ] = { + .name ="iocs" , .start =SA1100_CS3_PHYS , .end =SA1100_CS3_PHYS +0x01ffffff , .flags =IORESOURCE_MEM ,
@@ -276,6 +277,7 @@ .flags = IORESOURCE_IRQ, }, [2] = { + .name = "attrib", .start = SA1100_CS3_PHYS + 0x02000000, .end = SA1100_CS3_PHYS + 0x03ffffff, .flags = IORESOURCE_MEM,
arch/arm/mach-pxa/lubbock.c +2 -0
@@ -137,6 +137,7 @@static struct resource smc91x_resources[] = { [0 ] = { + .name ="iocs" , .start =0x0c000000 , .end =0x0c0fffff , .flags =IORESOURCE_MEM ,
@@ -147,6 +148,7 @@ .flags = IORESOURCE_IRQ, }, [2] = { + .name = "attrib", .start = 0x0e000000, .end = 0x0e0fffff, .flags = IORESOURCE_MEM,
Files declaring an smc91x platform device:
arch/ppc/platforms/4xx/redwood5.c
arch/ppc/platforms/4xx/redwood6.c
arch/arm/mach-pxa/lubbock.c
arch/arm/mach-pxa/mainstone.c
arch/arm/mach-sa1100/pleb.c
arch/arm/mach-sa1100/neponset.c
arch/arm/mach-lh7a40x/arch-lpd7a40x.c
arch/arm/mach-integrator/integrator_cp.c
arch/arm/mach-versatile/core.c
arch/arm/mach-omap/board-innovator.c
arch/arm/mach-omap/board-h3.c
arch/arm/mach-omap/board-perseus2.c
arch/arm/mach-omap/board-osk.c
arch/arm/mach-omap/board-h2.c
arch/sh/boards/superh/microdev/setup.c
arch/m32r/kernel/setup_opsput.c
arch/m32r/kernel/setup_mappi2.c
arch/m32r/kernel/setup_m32700ut.cSignature · 4 lines
Ian Campbell, Senior Design Engineer
Web: http://www.arcom.com
Arcom, Clifton Road, Direct: +44 (0)1223 403 465
Cambridge CB1 7EA, United Kingdom Phone: +44 (0)1223 411 200Quoted 11 lines · Ian Campbell
Quoted 1 line · Ian Campbell
Are you happy with "iocs", "attrib" and "datacs" for the names?
Of the platforms with an smc91x
platform_device(according to grep) only 2 (lubbock, neponset) out of the 18 have memory resources other than the iocs (full list of platforms is at the end, after the patch)So for the sake of the least intrusive patch I think for the main iocs I'll call
_bynameand fallback on mem resource number 0 if no named iocs resource exists. attrib and datacs must be explicitly named. This allows most of the board ports to remain unchanged.
Sensible.
Quoted 6 lines
I also noticed that the name propagates into
/proc/iomemetc# cat /proc/iomem [...] 10000000-10000003 : datacs 10000000-10000003 : smc91x so perhaps smc91x-datacs -attrib -iocs might be more appropriate names?
Probably, although "iocs" is rather criptic for someone not familiar with the chip. What about "smc91x-regs", "smc91x-attrib" and "smc91x-data32" ?
Nicolas
Quoted 6 lines · Nicolas Pitre
Quoted 1 line · Ian Campbell
so perhaps smc91x-datacs -attrib -iocs might be more appropriate names?
Probably, although "iocs" is rather criptic for someone not familiar with the chip. What about "smc91x-regs", "smc91x-attrib" and "smc91x-data32" ?
Sounds good. Are you happy for me to send the version below to Andrew and Jeff for inclusion? compiled on lubbock and neponset, compiled and tested on my platform.
Cheers,
Ian.
drivers/net/smc91x.c +108 -42
@@ -210,6 +210,10 @@spinlock_t lock; +#ifdef SMC_CAN_USE_DATACS +u32 *datacs; +#endif +#ifdef SMC_USE_PXA_DMA /* DMA needs the physical address of the chip */ u_long physaddr;
@@ -1998,16 +2002,21 @@return retval; } -static int smc_enable_device (unsigned long attrib_phys) +static int smc_enable_device (struct platform_device *pdev) {unsigned long flags;unsigned char ecor, ecsr;void *addr; +struct resource * res; + + res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-attrib" ); +if (!res) +return 0 ;/* * Map the attribute space. This is overkill, but clean. */ - addr =ioremap (attrib_phys,ATTRIB_SIZE ); + addr =ioremap (res->start,ATTRIB_SIZE );if (!addr)return -ENOMEM ;
@@ -2055,6 +2064,62 @@return 0 ; } +static int smc_request_attrib (struct platform_device *pdev) +{ +struct resource * res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-attrib" ); + +if (!res) +return 0 ; + +if (!request_mem_region (res->start,ATTRIB_SIZE ,CARDNAME )) +return -EBUSY ; + +return 0 ; +} + +static void smc_release_attrib (struct platform_device *pdev) +{ +struct resource * res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-attrib" ); + +if (res) +release_mem_region (res->start,ATTRIB_SIZE ); +} + +#ifdef SMC_CAN_USE_DATACS +static void smc_request_datacs (struct platform_device *pdev,struct net_device *ndev) +{ +struct resource * res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-data32" ); +struct smc_local *lp =netdev_priv (ndev); + +if (!res) +return ; + +if (!request_mem_region (res->start,SMC_DATA_EXTENT ,CARDNAME )) { +printk (KERN_INFO "%s: failed to request datacs memory region.\n" ,CARDNAME ); +return ; + } + + lp->datacs =ioremap (res->start,SMC_DATA_EXTENT ); +} + +static void smc_release_datacs (struct platform_device *pdev,struct net_device *ndev) +{ +struct smc_local *lp =netdev_priv (ndev); +struct resource * res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-data32" ); + +if (lp->datacs) +iounmap (lp->datacs); + + lp->datacs =NULL ; + +if (res) +release_mem_region (res->start,SMC_DATA_EXTENT ); +} +#else +static void smc_request_datacs (struct platform_device *pdev,struct net_device *ndev) {} +static void smc_release_datacs (struct platform_device *pdev,struct net_device *ndev) {} +#endif +/* * smc_init(void) * Input parameters:
@@ -2070,20 +2135,20 @@ {struct platform_device *pdev =to_platform_device (dev);struct net_device *ndev; -struct resource *res, *ext =NULL ; +struct resource *res;unsigned int *addr;int ret; - res =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); + res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-regs" ); +if (!res) + res =platform_get_resource (pdev,IORESOURCE_MEM ,0 );if (!res) { ret = -ENODEV ; goto out; } -/* -* Request the regions. -*/ -if (!request_mem_region (res->start,SMC_IO_EXTENT ,"smc91x" )) { + +if (!request_mem_region (res->start,SMC_IO_EXTENT ,CARDNAME )) { ret = -EBUSY ; goto out; }
@@ -2092,7 +2157,7 @@if (!ndev) {printk ("%s: could not allocate device.\n" ,CARDNAME ); ret = -ENOMEM ; - goto release_1; + goto out_release_io; }SET_MODULE_OWNER (ndev);SET_NETDEV_DEV (ndev, dev);
@@ -2100,42 +2165,26 @@ ndev->dma = (unsigned char )-1 ; ndev->irq =platform_get_irq (pdev,0 ); - ext =platform_get_resource (pdev,IORESOURCE_MEM ,1 ); -if (ext) { -if (!request_mem_region (ext->start,ATTRIB_SIZE , ndev->name)) { - ret = -EBUSY ; - goto release_1; - } - + ret =smc_request_attrib (pdev); +if (ret) + goto out_free_netdev;#if defined(CONFIG_SA1100_ASSABET ) -NCR_0 |=NCR_ENET_OSC_EN ; +NCR_0 |=NCR_ENET_OSC_EN ;#endif - - ret =smc_enable_device (ext->start); -if (ret) - goto release_both; - } + ret =smc_enable_device (pdev); +if (ret) + goto out_release_attrib; addr =ioremap (res->start,SMC_IO_EXTENT );if (!addr) { ret = -ENOMEM ; - goto release_both; + goto out_release_attrib; }dev_set_drvdata (dev, ndev); ret =smc_probe (ndev, (unsigned long )addr); -if (ret !=0 ) { -dev_set_drvdata (dev,NULL ); -iounmap (addr); - release_both: -if (ext) -release_mem_region (ext->start,ATTRIB_SIZE ); -free_netdev (ndev); - release_1: -release_mem_region (res->start,SMC_IO_EXTENT ); - out: -printk ("%s: not found (%d).\n" ,CARDNAME , ret); - } +if (ret !=0 ) + goto out_iounmap;#ifdef SMC_USE_PXA_DMA else {struct smc_local *lp =netdev_priv (ndev);
@@ -2143,6 +2192,22 @@ }#endif +smc_request_datacs (pdev, ndev); + +return 0 ; + + out_iounmap: +dev_set_drvdata (dev,NULL ); +iounmap (addr); + out_release_attrib: +smc_release_attrib (pdev); + out_free_netdev: +free_netdev (ndev); + out_release_io: +release_mem_region (res->start,SMC_IO_EXTENT ); + out: +printk ("%s: not found (%d).\n" ,CARDNAME , ret); +return ret; }
@@ -2163,10 +2228,13 @@pxa_free_dma (ndev->dma);#endif iounmap ((void *)ndev->base_addr); - res =platform_get_resource (pdev,IORESOURCE_MEM ,1 ); -if (res) -release_mem_region (res->start,ATTRIB_SIZE ); - res =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); + +smc_release_datacs (pdev,ndev); +smc_release_attrib (pdev); + + res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-regs" ); +if (!res) +platform_get_resource (pdev,IORESOURCE_MEM ,0 );release_mem_region (res->start,SMC_IO_EXTENT );free_netdev (ndev);
@@ -2195,9 +2263,7 @@if (ndev && level ==RESUME_ENABLE ) {struct smc_local *lp =netdev_priv (ndev); - -if (pdev->num_resources ==3 ) -smc_enable_device (pdev->resource[2 ].start); +smc_enable_device (pdev);if (netif_running (ndev)) {smc_reset (ndev);smc_enable (ndev);
drivers/net/smc91x.h +52 -7
90 lines not on this page · raw message
arch/arm/mach-sa1100/neponset.c +2 -0
@@ -266,6 +266,7 @@static struct resource smc91x_resources[] = { [0 ] = { + .name ="smc91x-regs" , .start =SA1100_CS3_PHYS , .end =SA1100_CS3_PHYS +0x01ffffff , .flags =IORESOURCE_MEM ,
@@ -276,6 +277,7 @@ .flags = IORESOURCE_IRQ, }, [2] = { + .name = "smc91x-attrib", .start = SA1100_CS3_PHYS + 0x02000000, .end = SA1100_CS3_PHYS + 0x03ffffff, .flags = IORESOURCE_MEM,
arch/arm/mach-pxa/lubbock.c +2 -0
@@ -137,6 +137,7 @@static struct resource smc91x_resources[] = { [0 ] = { + .name ="smc91x-regs" , .start =0x0c000000 , .end =0x0c0fffff , .flags =IORESOURCE_MEM ,
@@ -147,6 +148,7 @@ .flags = IORESOURCE_IRQ, }, [2] = { + .name = "smc91x-attrib", .start = 0x0e000000, .end = 0x0e0fffff, .flags = IORESOURCE_MEM,
Signature · 10 lines
Ian Campbell, Senior Design Engineer
Web: http://www.arcom.com
Arcom, Clifton Road, Direct: +44 (0)1223 403 465
Cambridge CB1 7EA, United Kingdom Phone: +44 (0)1223 411 200
_____________________________________________________________________
The message in this transmission is sent in confidence for the attention of the addressee only and should not be disclosed to any other party. Unauthorised recipients are requested to preserve this confidentiality. Please advise the sender if the addressee is not resident at the receiving end. Email to and from Arcom is automatically monitored for operational and lawful business reasons.
This message has been virus scanned by MessageLabs.Quoted 8 lines · Ian Campbell
Sounds good. Are you happy for me to send the version below to Andrew and Jeff for inclusion? compiled on lubbock and neponset, compiled and tested on my platform.
Cheers,
Ian.Signed-off-by Ian Campbell <[email protected]>
Quoted 398 lines
Index:
2.6/drivers/net/smc91x.c
===================================================================drivers/net/smc91x.c +108
-42@@ -210,6 +210,10 @@spinlock_t lock; +#ifdef SMC_CAN_USE_DATACS +u32 *datacs; +#endif +#ifdef SMC_USE_PXA_DMA /* DMA needs the physical address of the chip */ u_long physaddr;@@ -1998,16 +2002,21 @@return retval; } -static int smc_enable_device (unsigned long attrib_phys) +static int smc_enable_device (struct platform_device *pdev) {unsigned long flags;unsigned char ecor, ecsr;void *addr; +struct resource * res; + + res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-attrib" ); +if (!res) +return 0 ;/* * Map the attribute space. This is overkill, but clean. */ - addr =ioremap (attrib_phys,ATTRIB_SIZE ); + addr =ioremap (res->start,ATTRIB_SIZE );if (!addr)return -ENOMEM ;@@ -2055,6 +2064,62 @@return 0 ; } +static int smc_request_attrib (struct platform_device *pdev) +{ +struct resource * res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-attrib" ); + +if (!res) +return 0 ; + +if (!request_mem_region (res->start,ATTRIB_SIZE ,CARDNAME )) +return -EBUSY ; + +return 0 ; +} + +static void smc_release_attrib (struct platform_device *pdev) +{ +struct resource * res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-attrib" ); + +if (res) +release_mem_region (res->start,ATTRIB_SIZE ); +} + +#ifdef SMC_CAN_USE_DATACS +static void smc_request_datacs (struct platform_device *pdev,struct net_device *ndev) +{ +struct resource * res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-data32" ); +struct smc_local *lp =netdev_priv (ndev); + +if (!res) +return ; + +if (!request_mem_region (res->start,SMC_DATA_EXTENT ,CARDNAME )) { +printk (KERN_INFO "%s: failed to request datacs memory region.\n" ,CARDNAME ); +return ; + } + + lp->datacs =ioremap (res->start,SMC_DATA_EXTENT ); +} + +static void smc_release_datacs (struct platform_device *pdev,struct net_device *ndev) +{ +struct smc_local *lp =netdev_priv (ndev); +struct resource * res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-data32" ); + +if (lp->datacs) +iounmap (lp->datacs); + + lp->datacs =NULL ; + +if (res) +release_mem_region (res->start,SMC_DATA_EXTENT ); +} +#else +static void smc_request_datacs (struct platform_device *pdev,struct net_device *ndev) {} +static void smc_release_datacs (struct platform_device *pdev,struct net_device *ndev) {} +#endif +/* * smc_init(void) * Input parameters: @@ -2070,20 +2135,20 @@ {struct platform_device *pdev =to_platform_device (dev);struct net_device *ndev; -struct resource *res, *ext =NULL ; +struct resource *res;unsigned int *addr;int ret; - res =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); + res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-regs" ); +if (!res) + res =platform_get_resource (pdev,IORESOURCE_MEM ,0 );if (!res) { ret = -ENODEV ; goto out; } -/* -* Request the regions. -*/ -if (!request_mem_region (res->start,SMC_IO_EXTENT ,"smc91x" )) { + +if (!request_mem_region (res->start,SMC_IO_EXTENT ,CARDNAME )) { ret = -EBUSY ; goto out; }@@ -2092,7 +2157,7 @@if (!ndev) {printk ("%s: could not allocate device.\n" ,CARDNAME ); ret = -ENOMEM ; - goto release_1; + goto out_release_io; }SET_MODULE_OWNER (ndev);SET_NETDEV_DEV (ndev, dev);@@ -2100,42 +2165,26 @@ ndev->dma = (unsigned char )-1 ; ndev->irq =platform_get_irq (pdev,0 ); - ext =platform_get_resource (pdev,IORESOURCE_MEM ,1 ); -if (ext) { -if (!request_mem_region (ext->start,ATTRIB_SIZE , ndev->name)) { - ret = -EBUSY ; - goto release_1; - } - + ret =smc_request_attrib (pdev); +if (ret) + goto out_free_netdev;#if defined(CONFIG_SA1100_ASSABET ) -NCR_0 |=NCR_ENET_OSC_EN ; +NCR_0 |=NCR_ENET_OSC_EN ;#endif - - ret =smc_enable_device (ext->start); -if (ret) - goto release_both; - } + ret =smc_enable_device (pdev); +if (ret) + goto out_release_attrib; addr =ioremap (res->start,SMC_IO_EXTENT );if (!addr) { ret = -ENOMEM ; - goto release_both; + goto out_release_attrib; }dev_set_drvdata (dev, ndev); ret =smc_probe (ndev, (unsigned long )addr); -if (ret !=0 ) { -dev_set_drvdata (dev,NULL ); -iounmap (addr); - release_both: -if (ext) -release_mem_region (ext->start,ATTRIB_SIZE ); -free_netdev (ndev); - release_1: -release_mem_region (res->start,SMC_IO_EXTENT ); - out: -printk ("%s: not found (%d).\n" ,CARDNAME , ret); - } +if (ret !=0 ) + goto out_iounmap;#ifdef SMC_USE_PXA_DMA else {struct smc_local *lp =netdev_priv (ndev);@@ -2143,6 +2192,22 @@ }#endif +smc_request_datacs (pdev, ndev); + +return 0 ; + + out_iounmap: +dev_set_drvdata (dev,NULL ); +iounmap (addr); + out_release_attrib: +smc_release_attrib (pdev); + out_free_netdev: +free_netdev (ndev); + out_release_io: +release_mem_region (res->start,SMC_IO_EXTENT ); + out: +printk ("%s: not found (%d).\n" ,CARDNAME , ret); +return ret; }@@ -2163,10 +2228,13 @@pxa_free_dma (ndev->dma);#endif iounmap ((void *)ndev->base_addr); - res =platform_get_resource (pdev,IORESOURCE_MEM ,1 ); -if (res) -release_mem_region (res->start,ATTRIB_SIZE ); - res =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); + +smc_release_datacs (pdev,ndev); +smc_release_attrib (pdev); + + res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-regs" ); +if (!res) +platform_get_resource (pdev,IORESOURCE_MEM ,0 );release_mem_region (res->start,SMC_IO_EXTENT );free_netdev (ndev);@@ -2195,9 +2263,7 @@if (ndev && level ==RESUME_ENABLE ) {struct smc_local *lp =netdev_priv (ndev); - -if (pdev->num_resources ==3 ) -smc_enable_device (pdev->resource[2 ].start); +smc_enable_device (pdev);if (netif_running (ndev)) {smc_reset (ndev);smc_enable (ndev);Index:
2.6/drivers/net/smc91x.h
===================================================================drivers/net/smc91x.h +52
-7@@ -362,7 +362,7 @@#define SMC_IO_SHIFT 0#endif #define SMC_IO_EXTENT (16 << SMC_IO_SHIFT) - +#define SMC_DATA_EXTENT (4)/* . Bank Select Register: @@ -883,7 +883,7 @@#endif #if SMC_CAN_USE_32BIT -#define SMC_PUSH_DATA (p, l) \ +#define _SMC_PUSH_DATA (p, l) \ do { \ char *__ptr = (p); \ int __len = (l); \@@ -898,7 +898,7 @@SMC_outw ( *((u16 *)__ptr), ioaddr,DATA_REG ); \ } \ } while (0) -#define SMC_PULL_DATA (p, l) \ +#define _SMC_PULL_DATA (p, l) \ do { \ char *__ptr = (p); \ int __len = (l); \@@ -918,11 +918,11 @@SMC_insl ( ioaddr,DATA_REG , __ptr, __len >>2 ); \ } while (0)#elif SMC_CAN_USE_16BIT -#define SMC_PUSH_DATA (p, l) SMC_outsw( ioaddr, DATA_REG, p, (l) >> 1 ) -#define SMC_PULL_DATA (p, l) SMC_insw ( ioaddr, DATA_REG, p, (l) >> 1 ) +#define _SMC_PUSH_DATA (p, l) SMC_outsw( ioaddr, DATA_REG, p, (l) >> 1 ) +#define _SMC_PULL_DATA (p, l) SMC_insw ( ioaddr, DATA_REG, p, (l) >> 1 )#elif SMC_CAN_USE_8BIT -#define SMC_PUSH_DATA (p, l) SMC_outsb( ioaddr, DATA_REG, p, l ) -#define SMC_PULL_DATA (p, l) SMC_insb ( ioaddr, DATA_REG, p, l ) +#define _SMC_PUSH_DATA (p, l) SMC_outsb( ioaddr, DATA_REG, p, l ) +#define _SMC_PULL_DATA (p, l) SMC_insb ( ioaddr, DATA_REG, p, l )#endif #if !SMC_CAN_USE_16BIT @@ -941,6 +941,51 @@ })#endif +#if SMC_CAN_USE_DATACS +#define SMC_PUSH_DATA (p, l) \ + if ( lp->datacs ) { \ + unsigned char *__ptr = (p); \ + int __len = (l); \ + if (__len >= 2 && (unsigned long)__ptr & 2) { \ + __len -= 2; \ + SMC_outw( *((u16 *)__ptr), ioaddr, DATA_REG ); \ + __ptr += 2; \ + } \ + outsl(lp->datacs, __ptr, __len >> 2); \ + if (__len & 2) { \ + __ptr += (__len & ~3); \ + SMC_outw( *((u16 *)__ptr), ioaddr, DATA_REG ); \ + } \ + } else { \ + _SMC_PUSH_DATA(p, l); \ + } + +#define SMC_PULL_DATA (p, l) \ + if ( lp->datacs ) { \ + unsigned char *__ptr = (p); \ + int __len = (l); \ + if ((unsigned long)__ptr & 2) { \ +/* \ +* We want 32bit alignment here. \ +* Since some buses perform a full 32bit \ +* fetch even for 16bit data we can't use \ +* SMC_inw() here. Back both source (on chip \ +* and destination) pointers of 2 bytes. \ +*/ \ + __ptr -=2 ; \ + __len +=2 ; \ + SMC_SET_PTR( 2|PTR_READ|PTR_RCV|PTR_AUTOINC ); \ + } \ + __len +=2 ; \ +insl ( lp->datacs, __ptr, __len >>2 ); \ + } else { \ +_SMC_PULL_DATA (p, l); \ + } +#else +#define SMC_PUSH_DATA (p, l) _SMC_PUSH_DATA(p, l) +#define SMC_PULL_DATA (p, l) _SMC_PULL_DATA(p, l) +#endif +#if !defined (SMC_INTERRUPT_PREAMBLE )# define SMC_INTERRUPT_PREAMBLE #endif Index:
2.6/arch/arm/mach-sa1100/neponset.c
===================================================================arch/arm/mach-sa1100/neponset.c +2
-0@@ -266,6 +266,7 @@static struct resource smc91x_resources[] = { [0 ] = { + .name ="smc91x-regs" , .start =SA1100_CS3_PHYS , .end =SA1100_CS3_PHYS +0x01ffffff , .flags =IORESOURCE_MEM ,@@ -276,6 +277,7 @@ .flags = IORESOURCE_IRQ, }, [2] = { + .name = "smc91x-attrib", .start = SA1100_CS3_PHYS + 0x02000000, .end = SA1100_CS3_PHYS + 0x03ffffff, .flags = IORESOURCE_MEM,Index:
2.6/arch/arm/mach-pxa/lubbock.c
===================================================================arch/arm/mach-pxa/lubbock.c +2
-0@@ -137,6 +137,7 @@static struct resource smc91x_resources[] = { [0 ] = { + .name ="smc91x-regs" , .start =0x0c000000 , .end =0x0c0fffff , .flags =IORESOURCE_MEM ,@@ -147,6 +148,7 @@ .flags = IORESOURCE_IRQ, }, [2] = { + .name = "smc91x-attrib", .start = 0x0e000000, .end = 0x0e0fffff, .flags = IORESOURCE_MEM,Signature · 11 lines
-- Ian Campbell, Senior Design Engineer Web: http://www.arcom.com Arcom, Clifton Road, Direct: +44 (0)1223 403 465 Cambridge CB1 7EA, United Kingdom Phone: +44 (0)1223 411 200 _____________________________________________________________________ The message in this transmission is sent in confidence for the attention of the addressee only and should not be disclosed to any other party. Unauthorised recipients are requested to preserve this confidentiality. Please advise the sender if the addressee is not resident at the receiving end. Email to and from Arcom is automatically monitored for operational and lawful business reasons. This message has been virus scanned by MessageLabs.
Nicolas
PATCH 1/1 use datacs is smc91x driver
Hi,
Below is a patch to support the second 32-bit DATACS chipselect in the smc91x driver to transfer data. Support is enabled by adding a resource to the platform device named 'smc91x-data32'.
My platform has a 16-bit chip select for the primary IO region and no DMA. I found that throughput went from roughly 50mbit/s to 80mbit/s. I tested by throwing UDP packets at it using mgen (9000 packets/second with UDP payload of 1472 bytes is roughly 100mbit/s, I think) and counting the packets received in 60s, I then did the same for transmitting. The measurements are very rough but the improvement seems fairly significant to me.
Patch was compiled for lubbock and neponset and compiled and tested on my PXA platform.
drivers/net/smc91x.c +108 -42
@@ -210,6 +210,10 @@spinlock_t lock; +#ifdef SMC_CAN_USE_DATACS +u32 *datacs; +#endif +#ifdef SMC_USE_PXA_DMA /* DMA needs the physical address of the chip */ u_long physaddr;
@@ -1998,16 +2002,21 @@return retval; } -static int smc_enable_device (unsigned long attrib_phys) +static int smc_enable_device (struct platform_device *pdev) {unsigned long flags;unsigned char ecor, ecsr;void *addr; +struct resource * res; + + res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-attrib" ); +if (!res) +return 0 ;/* * Map the attribute space. This is overkill, but clean. */ - addr =ioremap (attrib_phys,ATTRIB_SIZE ); + addr =ioremap (res->start,ATTRIB_SIZE );if (!addr)return -ENOMEM ;
@@ -2055,6 +2064,62 @@return 0 ; } +static int smc_request_attrib (struct platform_device *pdev) +{ +struct resource * res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-attrib" ); + +if (!res) +return 0 ; + +if (!request_mem_region (res->start,ATTRIB_SIZE ,CARDNAME )) +return -EBUSY ; + +return 0 ; +} + +static void smc_release_attrib (struct platform_device *pdev) +{ +struct resource * res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-attrib" ); + +if (res) +release_mem_region (res->start,ATTRIB_SIZE ); +} + +#ifdef SMC_CAN_USE_DATACS +static void smc_request_datacs (struct platform_device *pdev,struct net_device *ndev) +{ +struct resource * res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-data32" ); +struct smc_local *lp =netdev_priv (ndev); + +if (!res) +return ; + +if (!request_mem_region (res->start,SMC_DATA_EXTENT ,CARDNAME )) { +printk (KERN_INFO "%s: failed to request datacs memory region.\n" ,CARDNAME ); +return ; + } + + lp->datacs =ioremap (res->start,SMC_DATA_EXTENT ); +} + +static void smc_release_datacs (struct platform_device *pdev,struct net_device *ndev) +{ +struct smc_local *lp =netdev_priv (ndev); +struct resource * res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-data32" ); + +if (lp->datacs) +iounmap (lp->datacs); + + lp->datacs =NULL ; + +if (res) +release_mem_region (res->start,SMC_DATA_EXTENT ); +} +#else +static void smc_request_datacs (struct platform_device *pdev,struct net_device *ndev) {} +static void smc_release_datacs (struct platform_device *pdev,struct net_device *ndev) {} +#endif +/* * smc_init(void) * Input parameters:
@@ -2070,20 +2135,20 @@ {struct platform_device *pdev =to_platform_device (dev);struct net_device *ndev; -struct resource *res, *ext =NULL ; +struct resource *res;unsigned int *addr;int ret; - res =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); + res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-regs" ); +if (!res) + res =platform_get_resource (pdev,IORESOURCE_MEM ,0 );if (!res) { ret = -ENODEV ; goto out; } -/* -* Request the regions. -*/ -if (!request_mem_region (res->start,SMC_IO_EXTENT ,"smc91x" )) { + +if (!request_mem_region (res->start,SMC_IO_EXTENT ,CARDNAME )) { ret = -EBUSY ; goto out; }
@@ -2092,7 +2157,7 @@if (!ndev) {printk ("%s: could not allocate device.\n" ,CARDNAME ); ret = -ENOMEM ; - goto release_1; + goto out_release_io; }SET_MODULE_OWNER (ndev);SET_NETDEV_DEV (ndev, dev);
@@ -2100,42 +2165,26 @@ ndev->dma = (unsigned char )-1 ; ndev->irq =platform_get_irq (pdev,0 ); - ext =platform_get_resource (pdev,IORESOURCE_MEM ,1 ); -if (ext) { -if (!request_mem_region (ext->start,ATTRIB_SIZE , ndev->name)) { - ret = -EBUSY ; - goto release_1; - } - + ret =smc_request_attrib (pdev); +if (ret) + goto out_free_netdev;#if defined(CONFIG_SA1100_ASSABET ) -NCR_0 |=NCR_ENET_OSC_EN ; +NCR_0 |=NCR_ENET_OSC_EN ;#endif - - ret =smc_enable_device (ext->start); -if (ret) - goto release_both; - } + ret =smc_enable_device (pdev); +if (ret) + goto out_release_attrib; addr =ioremap (res->start,SMC_IO_EXTENT );if (!addr) { ret = -ENOMEM ; - goto release_both; + goto out_release_attrib; }dev_set_drvdata (dev, ndev); ret =smc_probe (ndev, (unsigned long )addr); -if (ret !=0 ) { -dev_set_drvdata (dev,NULL ); -iounmap (addr); - release_both: -if (ext) -release_mem_region (ext->start,ATTRIB_SIZE ); -free_netdev (ndev); - release_1: -release_mem_region (res->start,SMC_IO_EXTENT ); - out: -printk ("%s: not found (%d).\n" ,CARDNAME , ret); - } +if (ret !=0 ) + goto out_iounmap;#ifdef SMC_USE_PXA_DMA else {struct smc_local *lp =netdev_priv (ndev);
@@ -2143,6 +2192,22 @@ }#endif +smc_request_datacs (pdev, ndev); + +return 0 ; + + out_iounmap: +dev_set_drvdata (dev,NULL ); +iounmap (addr); + out_release_attrib: +smc_release_attrib (pdev); + out_free_netdev: +free_netdev (ndev); + out_release_io: +release_mem_region (res->start,SMC_IO_EXTENT ); + out: +printk ("%s: not found (%d).\n" ,CARDNAME , ret); +return ret; }
@@ -2163,10 +2228,13 @@pxa_free_dma (ndev->dma);#endif iounmap ((void *)ndev->base_addr); - res =platform_get_resource (pdev,IORESOURCE_MEM ,1 ); -if (res) -release_mem_region (res->start,ATTRIB_SIZE ); - res =platform_get_resource (pdev,IORESOURCE_MEM ,0 ); + +smc_release_datacs (pdev,ndev); +smc_release_attrib (pdev); + + res =platform_get_resource_byname (pdev,IORESOURCE_MEM ,"smc91x-regs" ); +if (!res) +platform_get_resource (pdev,IORESOURCE_MEM ,0 );release_mem_region (res->start,SMC_IO_EXTENT );free_netdev (ndev);
@@ -2195,9 +2263,7 @@if (ndev && level ==RESUME_ENABLE ) {struct smc_local *lp =netdev_priv (ndev); - -if (pdev->num_resources ==3 ) -smc_enable_device (pdev->resource[2 ].start); +smc_enable_device (pdev);if (netif_running (ndev)) {smc_reset (ndev);smc_enable (ndev);
drivers/net/smc91x.h +52 -7
90 lines not on this page · raw message
arch/arm/mach-sa1100/neponset.c +2 -0
@@ -266,6 +266,7 @@static struct resource smc91x_resources[] = { [0 ] = { + .name ="smc91x-regs" , .start =SA1100_CS3_PHYS , .end =SA1100_CS3_PHYS +0x01ffffff , .flags =IORESOURCE_MEM ,
@@ -276,6 +277,7 @@ .flags = IORESOURCE_IRQ, }, [2] = { + .name = "smc91x-attrib", .start = SA1100_CS3_PHYS + 0x02000000, .end = SA1100_CS3_PHYS + 0x03ffffff, .flags = IORESOURCE_MEM,
arch/arm/mach-pxa/lubbock.c +2 -0
@@ -137,6 +137,7 @@static struct resource smc91x_resources[] = { [0 ] = { + .name ="smc91x-regs" , .start =0x0c000000 , .end =0x0c0fffff , .flags =IORESOURCE_MEM ,
@@ -147,6 +148,7 @@ .flags = IORESOURCE_IRQ, }, [2] = { + .name = "smc91x-attrib", .start = 0x0e000000, .end = 0x0e0fffff, .flags = IORESOURCE_MEM,
Signature · 4 lines
Ian Campbell, Senior Design Engineer
Web: http://www.arcom.com
Arcom, Clifton Road, Direct: +44 (0)1223 403 465
Cambridge CB1 7EA, United Kingdom Phone: +44 (0)1223 411 200