Skip to contentSkip to conversation

Huge unreliability - does Linux have something to do with it?

DISCUSSION jerome lacoste 12 participants 16 messages Feb 4, 2005 – Feb 6, 2005

lore
Share & tools
lore
#0 lore raw

[Sorry for the sensational title]

I have had this laptop for three years. It ran Linux (Debian unstable) from the start and its hardware has been very unreliable: I changed hard disks twice and the motherboard thrice. My DVD drive started failing some days ago (this one is 'original', 3 years old). But I don't mind as I am not under warranty anymore... This morning the machine booted with fsck errors on my hard disk. I am not sure if I did the right thing, but I said clear the inodes, and I ended up loosing some programs(*) (du, dircolors, etc..). The day starts well isn't it? Sounds like I will have to switch disks again...

I halted the machine correctly yesterday night. I never dropped the box in 3 years. Am I just being unlucky? Or could the fact that I am using Linux on the box affect the reliability in some ways on that particular hardware (Dell Inspiron 8100)? I run Linux on 3 other computers and never had single problems with them.

How can the file system (ext3) be messed up the way it was this morning after I stopped the machine correctly yesterday? Could a hardware failure look like bad sectors to fsck?

Attached the output of smartctl -a /dev/hda, whatever that helps.

Jerome

(*) I accept tips on discovering and maybe recovering which files have been taken out of my system...

smartctl version 5.32 Copyright (C) 2002-4 Bruce Allen Home page is http://smartmontools.sourceforge.net/

=== START OF INFORMATION SECTION ===

Device Model:     HITACHI_DK23FB-60
Serial Number:    1ZX822
Firmware Version: 00M0A0C1
Device is:        In smartctl database [for details use: -P show]
ATA Version is:   5
ATA Standard is:  ATA/ATAPI-5 T13 1321D revision 3
Local Time is:    Fri Feb  4 09:53:50 2005 CET
SMART support is: Available - device has SMART capability.
SMART support is: Enabled

=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED

General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever been run.
Total time to complete Offline
data collection: (2150) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support. Suspend Offline collection upon new command.
Offline surface scan supported. Self-test supported.
No Conveyance Self-test supported. Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 37) minutes.

SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds:

ID# ATTRIBUTE_NAME          FLAG     VALUE WORST THRESH TYPE      UPDATED  WHEN_FAILED RAW_VALUE
  1 Raw_Read_Error_Rate     0x000d   091   090   050    Pre-fail  Offline      -       412316862542
  2 Throughput_Performance  0x0005   100   092   050    Pre-fail  Offline      -       3140
  3 Spin_Up_Time            0x0007   100   100   050    Pre-fail  Always       -       0
  4 Start_Stop_Count        0x0032   100   100   000    Old_age   Always       -       388
  5 Reallocated_Sector_Ct   0x0033   095   095   010    Pre-fail  Always       -       142
  7 Seek_Error_Rate         0x000f   100   100   050    Pre-fail  Always       -       651
  8 Seek_Time_Performance   0x0005   100   100   050    Pre-fail  Offline      -       1125
  9 Power_On_Minutes        0x0032   095   095   000    Old_age   Always       -       2512h+02m
 10 Spin_Retry_Count        0x0013   100   100   050    Pre-fail  Always       -       0
 12 Power_Cycle_Count       0x0032   100   100   000    Old_age   Always       -       361
191 G-Sense_Error_Rate      0x000a   100   068   000    Old_age   Always       -       17536255
192 Power-Off_Retract_Count 0x0032   100   100   000    Old_age   Always       -       25
193 Load_Cycle_Count        0x0032   092   092   000    Old_age   Always       -       53398/53372
194 Temperature_Celsius     0x0022   072   036   000    Old_age   Always       -       54 (Lifetime Min/Max 72/13)
195 Hardware_ECC_Recovered  0x001a   100   001   000    Old_age   Always       -       4189
196 Reallocated_Event_Count 0x0032   086   086   000    Old_age   Always       -       142
197 Current_Pending_Sector  0x0032   097   094   000    Old_age   Always       -       3
198 Offline_Uncorrectable   0x0010   100   100   000    Old_age   Offline      -       0
199 UDMA_CRC_Error_Count    0x003e   200   200   000    Old_age   Always       -       0
200 Multi_Zone_Error_Rate   0x0013   100   100   050    Pre-fail  Always       -       0
201 Soft_Read_Error_Rate    0x0012   100   100   000    Old_age   Always       -       1
223 Load_Retry_Count        0x0012   100   100   000    Old_age   Always       -       0
230 Head_Amplitude          0x0032   096   096   000    Old_age   Always       -       141669
250 Read_Error_Retry_Rate   0x000a   100   001   000    Old_age   Always       -       837

SMART Error Log Version: 1
ATA Error Count: 108 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]
Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.

Error 108 occurred at disk power-on lifetime: 2511 hours (104 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 07 60 08 fb e1 Error: UNC 7 sectors at LBA = 0x01fb0860 = 33228896

Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 08 5f 08 fb e1 00      00:02:32.020  READ DMA
  c8 00 08 57 08 fb e1 00      00:02:32.010  READ DMA
  c8 00 08 4f 08 fb e1 00      00:02:32.010  READ DMA
  c8 00 08 47 08 fb e1 00      00:02:31.980  READ DMA
  c8 00 08 3f 08 fb e1 00      00:02:31.880  READ DMA

Error 107 occurred at disk power-on lifetime: 2511 hours (104 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 01 3d 08 fb e1 Error: UNC 1 sectors at LBA = 0x01fb083d = 33228861

Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 06 38 08 fb e1 00      00:01:33.860  READ DMA
  c8 00 07 37 08 fb e1 00      00:01:31.960  READ DMA
  c8 00 01 3e 08 fb e1 00      00:01:31.830  READ DMA
  c8 00 02 3d 08 fb e1 00      00:01:30.120  READ DMA
  c8 00 03 3c 08 fb e1 00      00:01:28.350  READ DMA

Error 106 occurred at disk power-on lifetime: 2511 hours (104 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 07 37 08 fb e1 Error: UNC 7 sectors at LBA = 0x01fb0837 = 33228855

Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 07 37 08 fb e1 00      00:01:31.960  READ DMA
  c8 00 01 3e 08 fb e1 00      00:01:31.830  READ DMA
  c8 00 02 3d 08 fb e1 00      00:01:30.120  READ DMA
  c8 00 03 3c 08 fb e1 00      00:01:28.350  READ DMA
  c8 00 04 3b 08 fb e1 00      00:01:26.090  READ DMA

Error 105 occurred at disk power-on lifetime: 2511 hours (104 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 3d 08 fb e1 Error: UNC 2 sectors at LBA = 0x01fb083d = 33228861

Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 02 3d 08 fb e1 00      00:01:30.120  READ DMA
  c8 00 03 3c 08 fb e1 00      00:01:28.350  READ DMA
  c8 00 04 3b 08 fb e1 00      00:01:26.090  READ DMA
  c8 00 05 3a 08 fb e1 00      00:01:24.160  READ DMA
  c8 00 06 39 08 fb e1 00      00:01:21.870  READ DMA

Error 104 occurred at disk power-on lifetime: 2511 hours (104 days + 15 hours)
When the command that caused the error occurred, the device was active or idle.

After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
40 51 02 3d 08 fb e1 Error: UNC 2 sectors at LBA = 0x01fb083d = 33228861

Commands leading to the command that caused the error were:

  CR FR SC SN CL CH DH DC   Powered_Up_Time  Command/Feature_Name
  -- -- -- -- -- -- -- --  ----------------  --------------------
  c8 00 03 3c 08 fb e1 00      00:01:28.350  READ DMA
  c8 00 04 3b 08 fb e1 00      00:01:26.090  READ DMA
  c8 00 05 3a 08 fb e1 00      00:01:24.160  READ DMA
  c8 00 06 39 08 fb e1 00      00:01:21.870  READ DMA
  c8 00 07 38 08 fb e1 00      00:01:19.790  READ DMA

SMART Self-test log structure revision number 1

Num  Test_Description    Status                  Remaining  LifeTime(hours)  LBA_of_first_error
# 1  Short offline       Completed without error       00%      2488         -
# 2  Short offline       Completed without error       00%      2464         -
# 3  Short offline       Completed without error       00%      2441         -
# 4  Extended offline    Completed: read failure       20%      2408         92491576
# 5  Short offline       Completed without error       00%      2407         -
# 6  Short offline       Completed without error       00%      2383         -
# 7  Short offline       Completed without error       00%      2296         -
# 8  Extended offline    Completed: read failure       20%      2273         92491576
# 9  Short offline       Completed without error       00%      2272         -
#10  Short offline       Completed without error       00%      2237         -
#11  Short offline       Completed without error       00%      2221         -
#12  Short offline       Completed without error       00%      2190         -
#13  Short offline       Completed without error       00%      2171         -
#14  Short offline       Completed without error       00%      2137         -
#15  Short offline       Completed without error       00%      2113         -
#16  Short offline       Completed without error       00%      2090         -
#17  Extended offline    Completed: read failure       20%      2067         92491576
#18  Short offline       Completed without error       00%      2066         -
#19  Short offline       Completed without error       00%      2044         -
#20  Short offline       Completed without error       00%      2020         -
#21  Short offline       Completed without error       00%      1996         -

SMART Selective self-test log data structure revision number 1

 SPAN  MIN_LBA  MAX_LBA  CURRENT_TEST_STATUS
    1        0        0  Not_testing
    2        0        0  Not_testing
    3        0        0  Not_testing
    4        0        0  Not_testing
    5        0        0  Not_testing

Selective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.

#1 lore raw
Quoted 22 lines · jerome lacoste

[Sorry for the sensational title]

I have had this laptop for three years. It ran Linux (Debian unstable) from the start and its hardware has been very unreliable: I changed hard disks twice and the motherboard thrice. My DVD drive started failing some days ago (this one is 'original', 3 years old). But I don't mind as I am not under warranty anymore... This morning the machine booted with fsck errors on my hard disk. I am not sure if I did the right thing, but I said clear the inodes, and I ended up loosing some programs(*) (du, dircolors, etc..). The day starts well isn't it? Sounds like I will have to switch disks again...

I halted the machine correctly yesterday night. I never dropped the box in 3 years. Am I just being unlucky? Or could the fact that I am using Linux on the box affect the reliability in some ways on that particular hardware (Dell Inspiron 8100)? I run Linux on 3 other computers and never had single problems with them.

How can the file system (ext3) be messed up the way it was this morning after I stopped the machine correctly yesterday? Could a hardware failure look like bad sectors to fsck?

Quoted 6 lines

Attached the output of smartctl -a /dev/hda, whatever that helps.

Jerome

(*) I accept tips on discovering and maybe recovering which files have been taken out of my system...

I honestly beleive that your simply out of luck, not that 3 years is alot for a laptop, but simply the "shit happens" thing.

Even though the Distro you run is tagged "Unstable" I'd rather run a battery of stress tools on your computer it before posting here, 'cus it's maybe a bit beyond the scope of lkml (I bet you tried more than one versions of the kernel in 3 years, problems never remain too long, I also hope you tried fresh installs too).

I don't think that en Inspiron 8100 carries anything exotic, so ... well... Go for a memtest86 then try disk stress tools (my memory wen't blank right now, ask google ;-) )

JB,
PS: Heu Jérome.... BTS Info Indus à l'Isle sur la Sorgue ?

Signature · 1 line
Julien Banchet <[email protected]>
#2 lore raw
In reply to jerome lacoste
Quoted 18 lines · jerome lacoste

[Sorry for the sensational title]

I have had this laptop for three years. It ran Linux (Debian unstable) from the start and its hardware has been very unreliable: I changed hard disks twice and the motherboard thrice. My DVD drive started failing some days ago (this one is 'original', 3 years old). But I don't mind as I am not under warranty anymore... This morning the machine booted with fsck errors on my hard disk. I am not sure if I did the right thing, but I said clear the inodes, and I ended up loosing some programs(*) (du, dircolors, etc..). The day starts well isn't it? Sounds like I will have to switch disks again...

I halted the machine correctly yesterday night. I never dropped the box in 3 years. Am I just being unlucky? Or could the fact that I am using Linux on the box affect the reliability in some ways on that particular hardware (Dell Inspiron 8100)? I run Linux on 3 other computers and never had single problems with them.

Quoted 4 lines

How can the file system (ext3) be messed up the way it was this morning after I stopped the machine correctly yesterday? Could a hardware failure look like bad sectors to fsck?

It can. I had a drive crash on my server a couple of months ago, and I had ext3 errors show up before the syslog filled up with the ide errors. The hard disk was only 1 1/2 years old.

If the bad sectors happen where directory inodes are written, your directory structure will be turned into swiss cheese. That will *definitely* cause ext3 errors, and dump you (in Red Hat systems, at least) to a shell on reboot.

Quoted 7 lines

Attached the output of smartctl -a /dev/hda, whatever that helps.

Jerome

(*) I accept tips on discovering and maybe recovering which files have been taken out of my system...

You might not have any luck. After fsck -f, I thought I had saved the drive, copied everything that was left onto another machine, and found that most of the larger files had holes in them - mp3's had skips, jpegs were completely corrupted, etc.

That's what made me get a backup FireWire drive... :)

#3 lore raw
In reply to jerome lacoste
Quoted 5 lines · In article <[email protected]> you wrote:

I halted the machine correctly yesterday night. I never dropped the box in 3 years. Am I just being unlucky? Or could the fact that I am using Linux on the box affect the reliability in some ways on that particular hardware (Dell Inspiron 8100)? I run Linux on 3 other computers and never had single problems with them.

There are a lot of possible problems with your actual hardware. Like Interrupt handling, power control, dma, ... Those are seldom but possible. Notebooks tend to require some special handling.

Quoted 1 line

Could a hardware failure look like bad sectors to fsck?

A failure of the bus or a former sporadic error can cause defective fs, but normally you have a read error in fsck no structure error.

Are you using hdparm? is the system perhaps overheating or overclocked?

Greetings
Bernd

#4 lore raw
Quoted 6 lines
Quoted 1 line

Could a hardware failure look like bad sectors to fsck?

A failure of the bus or a former sporadic error can cause defective fs, but normally you have a read error in fsck no structure error.

Are you using hdparm? is the system perhaps overheating or overclocked?

no overclock
hdparm is used but I cannot tell you exactly what the config is (now machine has been running memtest for 1.5 hour). I don't think I use special option: probably the defaults in my config file (mult_sect 16, dma on, write_cache off).

overheating: perhaps. The machine is hot and running many hours per day (usually 12-16). It s running the fans very often, but it's always been like that. I've tried to control the fan, but then the temperature goes high very quickly. So I let the fans run.

#5 lore raw
Quoted 6 lines · jerome lacoste
Quoted 5 lines · Bernd Eckenfels
Quoted 1 line

Could a hardware failure look like bad sectors to fsck?

A failure of the bus or a former sporadic error can cause defective fs, but normally you have a read error in fsck no structure error.

Quoted 7 lines
Quoted 1 line

Are you using hdparm? is the system perhaps overheating or overclocked?

no overclock
hdparm is used but I cannot tell you exactly what the config is (now machine has been running memtest for 1.5 hour). I don't think I use special option: probably the defaults in my config file (mult_sect 16, dma on, write_cache off).

There are combinations of IDE + disk that slowly corrupt filesystems with DMA on, if the default setting is DMA off _don't touch it_. Not all bad combinations are catched by the code in the kernel (intel + some Western Digital disk is what drove me up the wall until I disabled DMA).

What machine is this, what disk?

Quoted 4 lines

overheating: perhaps. The machine is hot and running many hours per day (usually 12-16). It s running the fans very often, but it's always been like that. I've tried to control the fan, but then the temperature goes high very quickly. So I let the fans run.

Wise decision.

Signature · 4 lines
Dr. Horst H. von Brand                   User #22616 counter.li.org
Departamento de Informatica                     Fono: +56 32 654431
Universidad Tecnica Federico Santa Maria              +56 32 654239
Casilla 110-V, Valparaiso, Chile                Fax:  +56 32 797513
#6 lore raw
In reply to jerome lacoste
Quoted 1 line · jerome lacoste

Attached the output of smartctl -a /dev/hda, whatever that helps.

Judging from the SMART output, this drive seems hosed. All firmware controlled extended off-line self-tests have failed on LBA 92491576, and it has a worrying amount of re-allocated sectors.

New laptop harddrives shouldn't be too hard to get hold of.

#7 lore raw
In reply to jerome lacoste

Hi Jerome :)

* jerome lacoste <[email protected]> dixit:

Quoted 1 line

[Sorry for the sensational title]

It catched my attention ;)))

Quoted 5 lines

I halted the machine correctly yesterday night. I never dropped the box in 3 years. Am I just being unlucky? Or could the fact that I am using Linux on the box affect the reliability in some ways on that particular hardware (Dell Inspiron 8100)? I run Linux on 3 other computers and never had single problems with them.

Well, Linux may stress the hardware more than other operating
systems because it tries to optimize usage and performance. But in this particular case I will think you are very unlucky O:) I've seen that before, unfortunately.

Quoted 1 line

Could a hardware failure look like bad sectors to fsck?

Yes, depending on the hardware failure.

Quoted 2 lines

(*) I accept tips on discovering and maybe recovering which files have been taken out of my system...

You should use 'integrit' (http://integrit.sourceforge.net). I
use it to know whether a file whose contents shouldn't change has changed, but it has more usages. And use memtest86 (there are two versions out there) to check your RAM, just in case. Bad RAM can cause 'apparent' hardware failures. A bad RAM chip can cause disk errors (if you write to disk from *bad* RAM, you'll write *bad* data) and other failures. Use 'integrit', read the documentation for details.

Good luck, you'll need it with that laptop :(

Raúl Núñez de Arenas Coronado

Signature · 3 lines
Linux Registered User 88736
http://www.dervishd.net & http://www.pleyades.net/
It's my PC and I'll cry if I want to...
#8 lore raw
In reply to jerome lacoste

Please keep me CCd

Quoted 1 line · jerome lacoste

particular hardware (Dell Inspiron 8100)? I run Linux on 3 other

I have this exact same laptop. It works perfectly for me with linux. Originally started with a 2.4 kernel and recently went to 2.6.10. The modem works well, the video card works well even with 3D accel. I replaced the original 30gb hdd with a 40gb (for space reasons). The only complaint about this thing I have is the fact they used an nvidia video chip. I have seen more than 4 months uptime on it (I used to use it as a desktop)

I did have a hardware mouse problem, but replacing the touchpad/palm rest fixed that. I'd give it a 4 star (out of five, mainly because of the video chipset and the keyboard layout)

Signature · 1 line
 Lab tests show that use of micro$oft causes cancer in lab animals
#9 lore raw
Quoted 12 lines · Wakko Warner

Please keep me CCd

Quoted 1 line · jerome lacoste

particular hardware (Dell Inspiron 8100)? I run Linux on 3 other

I have this exact same laptop. It works perfectly for me with linux. Originally started with a 2.4 kernel and recently went to 2.6.10. The modem works well, the video card works well even with 3D accel. I replaced the original 30gb hdd with a 40gb (for space reasons). The only complaint about this thing I have is the fact they used an nvidia video chip. I have seen more than 4 months uptime on it (I used to use it as a desktop)

Quoted 4 lines

I did have a hardware mouse problem, but replacing the touchpad/palm rest fixed that. I'd give it a 4 star (out of five, mainly because of the video chipset and the keyboard layout)

Hmm, I guess it's a hit and run. I had replaced:

1. Fan assembly (was making grinding sounds after 1.5 years)
2. DVD-CDRW combo (Samsung SN-308B could not really read pretty much anything but burns pretty well)
3. LCD (backlight burned out and I managed to tear connectors on the panel trying to see if I can replace the light and what part shoudl I order). Well, that helped to persuade my better half that I really need 1600x1200 ;)
4. Original Hitachi hard driver died horrible death - I returned home and heard it making grinding sounds and hitting heads against something.
5. Replacement IBM drive has developed a few bad sectors, need to arrange replacement.

But I guess all of it has something to do with being on 24/7. I am not complaining, I like the box, especially the touchpad ;)

Signature · 1 line
Dmitry
#10 lore raw

Dell Inspiron sensors (was: Re: Huge unreliability - does Linux have something to do with it?)

Quoted 8 lines · Dmitry Torokhov
Quoted 1 line · Wakko Warner
Quoted 1 line

particular hardware (Dell Inspiron 8100)? I run Linux on 3 other

Hmm, I guess it's a hit and run. I had replaced:

4. Original Hitachi hard driver died horrible death - I returned home and heard it making grinding sounds and hitting heads against something.

I have a Dell Inspiron 8200, from March 2002. Since end of December 2004 I've started having system lockups which at first I couldn't identify, although they seemed to be overheating related. So I started monitoring the temperatures on all the components in my system (I can monitor CPU, GPU and HD temp; more on this later), and noticed that the lockups happen when the HD temp gets around 40 C. Indeed, they are 99% of the time preceded by a loud "click" coming from the HD wereabouts ... haven't lost any data yet but I've started backing up everything and getting ready to get a replacement HD.

Concerning sensors, though: under Windows I can use the i8kfangui applet to monitor all the sensors provided in the computer, but under Linux I only seem able to get the CPU temperature, using the i8k module, and no other sensor module seems to be loadable. Does anybody know how to access the other sensors on the Dell Inspiron? Or should I suggest Massimo to upgrade the i8k module to add the new sensors (i8kfangui has a GPL source code so it shouldn't be a problem) and possibly interface it all with the Linux sensors framework?

Signature · 7 lines
Giuseppe "Oblomov" Bilotta

Can't you see
It all makes perfect sense
Expressed in dollar and cents
Pounds shillings and pence
                  (Roger Waters)
#11 lore raw

Re: Dell Inspiron sensors (was: Re: Huge unreliability - does Linux have something to do with it?)

Quoted 10 lines · Giuseppe Bilotta

I have a Dell Inspiron 8200, from March 2002. Since end of December 2004 I've started having system lockups which at first I couldn't identify, although they seemed to be overheating related. So I started monitoring the temperatures on all the components in my system (I can monitor CPU, GPU and HD temp; more on this later), and noticed that the lockups happen when the HD temp gets around 40 C. Indeed, they are 99% of the time preceded by a loud "click" coming from the HD wereabouts ... haven't lost any data yet but I've started backing up everything and getting ready to get a replacement HD.

You might want to try this;

Remove the keyboard, remove the cover beneath. Take a can of air dust (or equivalent) and *carefully* blow out the inside of the laptop.

-then-

Look at the back side and the right side of the laptop. You'll see the intake for air and the A/C unit. Take that air dust and blow in such
that the plastic fan whirls away. Take a snapshot of the dust bunnies
and send them to Dell.

I have a 5150 Inspiron. In less than 1 year this thing started powering off (hard) on its own, no matter the OS installed (multi-boot). I dug around the 'net and found similar issues, all relating to OVERHEATING. Poorly designed was the culprit, but Dell has not yet admitted to this (but look at the Dell Linux forum or just Dell laptop forum and see Dell's techs replies) - think of the numbers sold and it makes sense.

Anyways, aside from that, I had a dust bunny the size of a U.S. quarter fly out. Since then I make certain to rest it on a flat surface (I cut some steel and carry it with me) and every couple of months take it apart as described and blow out the dust.

-fd

#12 lore raw

Re: Dell Inspiron sensors (was: Re: Huge unreliability - does Linux have something to do with it?)

Quoted 12 lines · kernel

You might want to try this;

Remove the keyboard, remove the cover beneath. Take a can of air dust (or equivalent) and *carefully* blow out the inside of the laptop.

-then-

Look at the back side and the right side of the laptop. You'll see the intake for air and the A/C unit. Take that air dust and blow in such
that the plastic fan whirls away. Take a snapshot of the dust bunnies
and send them to Dell.

Quoted 6 lines

I have a 5150 Inspiron. In less than 1 year this thing started powering off (hard) on its own, no matter the OS installed (multi-boot). I dug around the 'net and found similar issues, all relating to OVERHEATING. Poorly designed was the culprit, but Dell has not yet admitted to this (but look at the Dell Linux forum or just Dell laptop forum and see Dell's techs replies) - think of the numbers sold and it makes sense.

Thank you very much for the pointers. I had just reached the same conclusion this afternoon, when pissed off by finding the CPU was at 85 C despite the fans being on at the max I did exactly what you suggest; although I didn't find any dust bunny, a thorough cleanup and blowing plus some toothpicking of hair and whatnot, I find myself with a computer that is running finely --again :)

Too bad, I'll need another excuse to buy myself the new hard disk ...

What about the sensors?

Signature · 7 lines
Giuseppe "Oblomov" Bilotta

Can't you see
It all makes perfect sense
Expressed in dollar and cents
Pounds shillings and pence
                  (Roger Waters)
#13 lore raw
In reply to Wakko Warner

Took

Quoted 11 lines · Wakko Warner

Please keep me CCd

Quoted 1 line · jerome lacoste

particular hardware (Dell Inspiron 8100)? I run Linux on 3 other

I have this exact same laptop. It works perfectly for me with linux. Originally started with a 2.4 kernel and recently went to 2.6.10. The modem works well, the video card works well even with 3D accel. I replaced the original 30gb hdd with a 40gb (for space reasons). The only complaint about this thing I have is the fact they used an nvidia video chip. I have seen more than 4 months uptime on it (I used to use it as a desktop)

I sometimes use it as a desktop. Thing is as I never took the time to try to make work sw suspend, I'd rather have it running all the time than to restart it every now and then.

While looking for a replacement disk, I've seen that some new disks were "designed for continuous, 24/7 operation".

E.g. http://www6.tomshardware.com/storage/20030813/mini-harddisks-01.html

Not sure how good that is, but I will sure look into it...

Thanks for all who answered. If you want to further the talk, it maybe better to take this off lkml now.

J

#14 lore raw
In reply to Wakko Warner
Quoted 11 lines · Wakko Warner

Please keep me CCd

Quoted 1 line · jerome lacoste

particular hardware (Dell Inspiron 8100)? I run Linux on 3 other

I have this exact same laptop. It works perfectly for me with linux. Originally started with a 2.4 kernel and recently went to 2.6.10. The modem works well, the video card works well even with 3D accel. I replaced the original 30gb hdd with a 40gb (for space reasons). The only complaint about this thing I have is the fact they used an nvidia video chip. I have seen more than 4 months uptime on it (I used to use it as a desktop)

I think it does not like being moved. A friend of mine had his one repaired several times because of either hard disk failures, backlight failure and the machine refusing to boot at all. I've never seen such unreliable hardware!

Willy

#15 lore raw

Please keep me CCd

Quoted 11 lines · Willy Tarreau
Quoted 6 lines · Wakko Warner

I have this exact same laptop. It works perfectly for me with linux. Originally started with a 2.4 kernel and recently went to 2.6.10. The modem works well, the video card works well even with 3D accel. I replaced the original 30gb hdd with a 40gb (for space reasons). The only complaint about this thing I have is the fact they used an nvidia video chip. I have seen more than 4 months uptime on it (I used to use it as a desktop)

I think it does not like being moved. A friend of mine had his one repaired several times because of either hard disk failures, backlight failure and the machine refusing to boot at all. I've never seen such unreliable hardware!

Mine didn't have that problem. At the time it was the fastest machine I had. I got away from it though with my nice xeon box =)

I have never heard of a machine that if you move it it'd quit working. That's bad. I have heard of a machine quit working because someone looked at it the wrong way.

Signature · 1 line
 Lab tests show that use of micro$oft causes cancer in lab animals