add TP560 data/fax/modem support
Subsystems (2)
PATCH 1/1 add TP560 data/fax/modem support
Claim Topic TP560 data/fax/voice modem. This device reports as class 0x0780, so we don't claim it by default:
00:0d.0 Class 0780: 151f:0000 Subsystem: 151f:0000 Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at a400 [size=8] 00: 1f 15 00 00 01 00 00 02 00 00 80 07 00 00 00 00 10: 01 a4 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 1f 15 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00
Some rc.serial scripts extract IRQ and I/O port information from /proc/pci and stuff it into an unused port using setserial. That doesn't work reliably anymore because pci_enable_device() is never called, so the IRQ may not be enabled.
Thanks to Evan Clarke for reporting and helping debug this problem.
===== drivers/serial/8250_pci.c 1.48 vs edited =====
drivers/serial/8250_pci.c +7 -0
@@ -2212,6 +2212,13 @@ 0, pbn_exar_XR17C158 },/* +* Topic TP560 Data/Fax/Voice 56k modem (reported by Evan Clarke) +*/ + {PCI_VENDOR_ID_TOPIC ,PCI_DEVICE_ID_TOPIC_TP560 , +PCI_ANY_ID ,PCI_ANY_ID ,0 ,0 , + pbn_b0_1_115200 }, + +/* * These entries match devices with class COMMUNICATION_SERIAL, * COMMUNICATION_MODEM or COMMUNICATION_MULTISERIAL */
===== include/linux/pci_ids.h 1.200 vs edited =====
include/linux/pci_ids.h +3 -0
@@ -1972,6 +1972,9 @@#define PCI_DEVICE_ID_BCM4401 0x4401#define PCI_DEVICE_ID_BCM4401B0 0x4402 +#define PCI_VENDOR_ID_TOPIC 0x151f +#define PCI_DEVICE_ID_TOPIC_TP560 0x0000 +#define PCI_VENDOR_ID_ENE 0x1524#define PCI_DEVICE_ID_ENE_1211 0x1211#define PCI_DEVICE_ID_ENE_1225 0x1225
I thought somebody promised to add a pci_route_irq(dev) or some such so that the device didn't have to be enabled before the IRQ was correct.
I first reported this bad IRQ problem back in December of 2004. Has the new function been added?
Quoted 54 lines · Bjorn Helgaas
Claim Topic TP560 data/fax/voice modem. This device reports as class
0x0780, so we don't claim it by default:00:0d.0 Class 0780: 151f:0000 Subsystem: 151f:0000 Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at a400 [size=8] 00: 1f 15 00 00 01 00 00 02 00 00 80 07 00 00 00 00 10: 01 a4 00 00 00 00 00 00 00 00 00 00 00 00 00 00 20: 00 00 00 00 00 00 00 00 00 00 00 00 1f 15 00 00 30: 00 00 00 00 00 00 00 00 00 00 00 00 0b 01 00 00Some rc.serial scripts extract IRQ and I/O port information from
/proc/pciand stuff it into an unused port using setserial. That doesn't work reliably anymore becausepci_enable_device()is never called, so the IRQ may not be enabled.Thanks to Evan Clarke for reporting and helping debug this problem.
Signed-off-by Bjorn Helgaas <[email protected]>=====
drivers/serial/8250_pci.c1.48 vs edited =====drivers/serial/8250_pci.c +7
-0@@ -2212,6 +2212,13 @@ 0, pbn_exar_XR17C158 },/* +* Topic TP560 Data/Fax/Voice 56k modem (reported by Evan Clarke) +*/ + {PCI_VENDOR_ID_TOPIC ,PCI_DEVICE_ID_TOPIC_TP560 , +PCI_ANY_ID ,PCI_ANY_ID ,0 ,0 , + pbn_b0_1_115200 }, + +/* * These entries match devices with class COMMUNICATION_SERIAL, * COMMUNICATION_MODEM or COMMUNICATION_MULTISERIAL */=====
include/linux/pci_ids.h1.200 vs edited =====include/linux/pci_ids.h +3
-1@@ -1972,6 +1972,9 @@#define PCI_DEVICE_ID_BCM4401 0x4401#define PCI_DEVICE_ID_BCM4401B0 0x4402 +#define PCI_VENDOR_ID_TOPIC 0x151f +#define PCI_DEVICE_ID_TOPIC_TP560 0x0000 +#define PCI_VENDOR_ID_ENE 0x1524#define PCI_DEVICE_ID_ENE_1211 0x1211#define PCI_DEVICE_ID_ENE_1225 0x1225 -
Quoted 5 lines
To unsubscribe from this list: send the line "unsubscribe linux-kernel" in the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
Cheers,
Dick Johnson
Penguin : Linux version 2.6.10 on an i686 machine (5537.79 BogoMips).
Notice : All mail here is now cached for review by Dictator Bush.
98.36% of all statistics are fiction.
Quoted 6 lines · linux-os
I thought somebody promised to add a
pci_route_irq(dev)or some such so that the device didn't have to be enabled before the IRQ was correct.I first reported this bad IRQ problem back in December of 2004. Has the new function been added?
That's a completely different problem. The point here is that the serial driver currently doesn't do anything with the TP560 (no pci_enable_device(), no pci_route_irq(), no nothing). Then when setserial comes along and force-feeds the driver with the IO and IRQ info, there's nothing at that point that does anything to enable the device or route its interrupt either.
I did raise the idea of adding a pci_route_irq() interface, but to be honest, I was never convinced of its general usefulness. I haven't heard of any driver in the tree that requires it, so it's not clear that it would be accepted even if I (or you) wrote it.
I think you mentioned a specific PCI interface chip that was susceptible to the problem; is there a public reference that would help explicate the situation?
Quoted 15 lines · Bjorn Helgaas
Quoted 6 lines · linux-os
I thought somebody promised to add a
pci_route_irq(dev)or some such so that the device didn't have to be enabled before the IRQ was correct.I first reported this bad IRQ problem back in December of 2004. Has the new function been added?
That's a completely different problem. The point here is that the serial driver currently doesn't do anything with the TP560 (no
pci_enable_device(), nopci_route_irq(), no nothing). Then when setserial comes along and force-feeds the driver with the IO and IRQ info, there's nothing at that point that does anything to enable the device or route its interrupt either.
Quoted 2 lines
I did raise the idea of adding a
pci_route_irq()interface, but to be honest, I was never convinced of its general usefulness.
There have been two PCI drivers in the past three days where users have reported that the IRQ was wrong. One patch was provided to enable the device before requesting the IRQ, this being inherently dangerous. So, if you are the one who re-wrote the PCI stuff so that the IRQ is wrong when the device is claimed, then I think you have a duty to fix the code that you have broken.
The correct way to fix the broken code is to make sure that the IRQ, reported in the structure, is correct. Alternate methods might be a pci_route_irq() function.
The existing PCI code is broken. The fact that an invalid IRQ is reported in the structure is PROOF that it is broken and requires no further discussion. Many of us have to use this stuff in a professional environment, we can't enable devices without an interrupt handler in place because it is not allowed in code that is subject to peer review. We also can't use code when such problems as invalid values in returned data are discovered.
Two months ago I discovered this problem and reported it, hoping that the person who broke existing code would fix it. It has not been fixed.
Cheers,
Dick Johnson
Penguin : Linux version 2.6.10 on an i686 machine (5537.79 BogoMips).
Notice : All mail here is now cached for review by Dictator Bush.
98.36% of all statistics are fiction.
This discussion has nothing to do with serial, so I'm going to respond more completely but remove Russell and linux-serial and add linux-pci. Just FYI.
Quoted 6 lines · linux-os
Quoted 4 lines · Bjorn Helgaas
Quoted 3 lines · linux-os
I thought somebody promised to add a
pci_route_irq(dev)or some such so that the device didn't have to be enabled before the IRQ was correct.
Quoted 17 lines · linux-os
Quoted 15 lines · Bjorn Helgaas
Quoted 6 lines · linux-os
I thought somebody promised to add a
pci_route_irq(dev)or some such so that the device didn't have to be enabled before the IRQ was correct.I first reported this bad IRQ problem back in December of 2004. Has the new function been added?
That's a completely different problem. The point here is that the serial driver currently doesn't do anything with the TP560 (no
pci_enable_device(), nopci_route_irq(), no nothing). Then when setserial comes along and force-feeds the driver with the IO and IRQ info, there's nothing at that point that does anything to enable the device or route its interrupt either.
Quoted 5 lines
Quoted 2 lines
I did raise the idea of adding a
pci_route_irq()interface, but to be honest, I was never convinced of its general usefulness.There have been two PCI drivers in the past three days where users have reported that the IRQ was wrong.
If you've got pointers to these two reports, please provide them.
Quoted 6 lines
One patch was
provided to enable the device before requesting the IRQ, this being inherently dangerous. So, if you are the one who re-wrote the PCI stuff so that the IRQ is wrong when the device is claimed, then I think you have a duty to fix the code that you have broken.
Most drivers in the tree call pci_enable_device() before request_irq(). That was the case even before my changes. Dangerous? Maybe, but I didn't make it more so.
Quoted 3 lines
The correct way to fix the broken code is to make sure that the IRQ, reported in the structure, is correct. Alternate methods might be a
pci_route_irq()function.
Or perhaps, the IRQ could be routed in pci_setup_device(). But, by the principle of "if you don't use it, don't touch it", there *is* something to be said for the fact that the current code doesn't touch IRQ routing unless a driver actually claims the device.
Quoted 3 lines
The existing PCI code is broken. The fact that an invalid IRQ is reported in the structure is PROOF that it is broken and requires no further discussion.
Then I'm sure your patch to fix it will be accepted without much dissent.
Quoted 6 lines
Many of us have to
use this stuff in a professional environment, we can't enable devices without an interrupt handler in place because it is not allowed in code that is subject to peer review. We also can't use code when such problems as invalid values in returned data are discovered.
Nobody's forcing you to use "this stuff."
Quoted 3 lines
Two months ago I discovered this problem and reported it, hoping that the person who broke existing code would fix it. It has not been fixed.
The fact is, yours is the only report of an issue with the structure of the new code. And it apparently only concerns an out-of-tree driver. Still, I agree that it might be good to do something about it. But you haven't provided pointers to the hardware specs or driver involved. So I'm not going to go too much out of my way to fix it.
Russell King
AppliedQuoted 2 lines · Bjorn Helgaas
Claim Topic TP560 data/fax/voice modem. This device reports as class
0x0780, so we don't claim it by default:
Applied, thanks.
Signature · 4 lines
Russell King
Linux kernel 2.6 ARM Linux - http://www.arm.linux.org.uk/
maintainer of: 2.6 PCMCIA - http://pcmcia.arm.linux.org.uk/
2.6 Serial core