Skip to contentSkip to conversation

at45 dataflash

U-Boot-Users Z.N. 3 participants 5 messages Feb 8, 2005 – Feb 12, 2005

lore
Share & tools
lore

Z.N.

author
#0 lore raw

Hi!

I'm running u-boot 1.1.2 on an AT91 compatible board, however I have no NAND flash, only serial dataflash.

As far as I've looked at the sources, there is a configuration option that I can store environment variables on the dataflash, however how can I load the kernel image & ramdisk image from dataflash into SDRAM? (I've found no commands to do this, maybe I overlooked it somewhere..)

If there is no way to do this, what if I load the kernel image together with u-boot into sdram on startup, can u-boot start this "pre-loaded" kernel image?

Thank you for you answers!

Best Regards,
Zoli

#1 lore raw
Quoted 5 lines · In message <1107905713.9293.9.camel@localhost> you wrote:

As far as I've looked at the sources, there is a configuration option that I can store environment variables on the dataflash, however how can I load the kernel image & ramdisk image from dataflash into SDRAM? (I've found no commands to do this, maybe I overlooked it somewhere..)

You use the same commands as for NOR flash. Dataflash support was intergrated transparently.

Quoted 3 lines

If there is no way to do this, what if I load the kernel image together with u-boot into sdram on startup, can u-boot start this "pre-loaded" kernel image?

In theory it can. [And actually it most probably will.]

However, you are aware that U-Boot expects to be started fresh out of reset on a completely uninitialized system, and on such a system you cannot have any SDRAM contents as the SDRAM has not been initialized yet. I guess you may want to read the FAQ at
http://www.denx.de/twiki/bin/view/DULG/CanUBootBeConfiguredSuchThatItCanBeStartedInRAM

Best regards,

Wolfgang Denk

Signature · 5 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
"And it should be the law: If you use  the  word  `paradigm'  without
knowing  what  the  dictionary  says  it  means,  you  go to jail. No
exceptions."                     - David Jones @ Megatest Corporation
author
#2 lore raw

Hi!

Thanks for the reply!

This is how u-boot boots for me:

U-Boot 1.1.2 (Feb 9 2005 - 16:43:51)

U-Boot code: 21F00000 -> 21F16F40 BSS: -> 21F1B5F8 RAM Configuration:
Bank #0: 20000000 32 MB
Atmel: Flash: 0 kB
Error Timeout
DataFlash:AT45DB161

Nb pages:   4096
Page Size:    528

Size= 2162688 bytes
Logical address: 0xC0000000
Area 0: C0000000 to C0007FFF (RO)
Area 1: C0008000 to C001FFFF (RO)
Area 2: C0020000 to C0027FFF
Area 3: C0028000 to C020FFFF
*** Warning - bad CRC, using default environment

In:    serial
Out:   serial
Err:   serial

U-Boot>

And if I display the contents of the Dataflash, the following happens:

U-Boot> md c0000000
c0000000:Error Timeout
Error Timeout
data abort

pc : [<21f08648>]    lr : [<21f12310>]

sp : 21eddc38 ip : 21edda28 fp : 21eddc7c
r10: c0000000 r9 : 00000100 r8 : 21eddfdc
r7 : 00000010 r6 : 00000000 r5 : 00000004 r4 : 21eddc48 r3 : 00000000 r2 : fffff200 r1 : 21edda5c r0 : ffffffff
Flags: nZCv IRQs off FIQs off Mode SVC_32 Resetting CPU ...

How come that the dataflash _gets detected_, however it is not _readable_?!

(I only have dataflash no NAND flash..)

I've tried to set CFG_MAX_FLASH_BANKS and CFG_MAX_NAND_DEVICE to 0, but this did not help (same as above). How can I remove NAND support from my config? (Maybe that is the cause of the dataflash errors..)

I hope Wolfgang or someone could give me a hint (or some pointers to the documentation..)

Best regards,
Zoli

PS:

In fact I've also tried to use the Atmel supplied loader.bin to load the u-boot image, with the following results:

When the loader.bin image is running on the board, and outputting the 'C' characters, waiting for the Xmodem transfer. Then, the following happens during the Xmodem transfer:

sx -X u-boot.bin </dev/ttyS0 >/dev/ttyS0
Sending u-boot.bin, 728 blocks: Give your local XMODEM receive command now.
Xmodem sectors/kbytes sent: 0/ 0kRetry 0: NAK on sector
Retry 0: NAK on sector
Retry 0: NAK on sector
Retry 0: NAK on sector
Retry 0: NAK on sector
Retry 0: NAK on sector
Retry 0: NAK on sector
Retry 0: NAK on sector
Retry 0: NAK on sector
Retry 0: NAK on sector
Retry 0: NAK on sector
Retry 0: Retry Count Exceeded

Transfer incomplete

Have anyone experienced such thing?

Quoted 25 lines · Wolfgang Denk
Quoted 5 lines · In message <1107905713.9293.9.camel@localhost> you wrote:

As far as I've looked at the sources, there is a configuration option that I can store environment variables on the dataflash, however how can I load the kernel image & ramdisk image from dataflash into SDRAM? (I've found no commands to do this, maybe I overlooked it somewhere..)

You use the same commands as for NOR flash. Dataflash support was intergrated transparently.

Quoted 3 lines

If there is no way to do this, what if I load the kernel image together with u-boot into sdram on startup, can u-boot start this "pre-loaded" kernel image?

In theory it can. [And actually it most probably will.]

However, you are aware that U-Boot expects to be started fresh out of reset on a completely uninitialized system, and on such a system you cannot have any SDRAM contents as the SDRAM has not been initialized yet. I guess you may want to read the FAQ at
http://www.denx.de/twiki/bin/view/DULG/CanUBootBeConfiguredSuchThatItCanBeStartedInRAM

Best regards,

Wolfgang Denk

#3 lore raw

Hello

Never worked with SPI flash in u-boot yet...but... are you sure it gets detected correctly?

Quoted 2 lines

Atmel: Flash: 0 kB
Error Timeout

For me a "Timeout" doesn't tell me that a device is recognized properly (o;

Quoted 4 lines

DataFlash:AT45DB161

Nb pages:   4096
Page Size:    528

Size= 2162688 bytes

rick

author
#4 lore raw

Hi!

Quoted 7 lines

Never worked with SPI flash in u-boot yet...but... are you sure it gets detected correctly?

Quoted 2 lines

Atmel: Flash: 0 kB
Error Timeout

For me a "Timeout" doesn't tell me that a device is recognized properly (o;

isnt this Timeout message refer to the parallel NAND flash? (since there is no NAND flash in the design, this would be natural)

Zoli