DriveStatusError BadCRC
I bought new Maxtor HD 80 GB but somthing Fedora Core 3 crashes giving this
message:
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: Error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: Error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
.
.
.
hda: dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda: dma_intr: Error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
ide0: reset: success
Kernel panic - not syncing: mm/mmap.c:534: spin_lock(mm/rmap.c:cb80cf08)
already locked by /0. (Not tainted)
[c0120445] panic+0x42/0x1c0
[c015e1e1] vma_prio_tree_insert+017/0x2a
[c01656d3] vma_adjust+0x322/0x556
[c0166f30] split_vma+0xdd/0xf5
[c0167c70] mprotect_fixup+0xf1/0x1ca
[c0167edb] sys_mprotect+0192/0x253
[c010392d] syscall_call+0x7/0xb
How can I solve it ?
__________________________________________________________________
TISCALI ADSL 1.25 MEGA
Solo con Tiscali Adsl navighi senza limiti e telefoni senza canone Telecom a partire da 19,95 Euro/mese.
Attivala entro il 28 luglio, il primo MESE è GRATIS! CLICCA QUI.
http://abbonati.tiscali.it/adsl/sa/1e25flat_tc/
Quoted 7 lines · On Fri, 22 Jul 2005, [email protected] wrote:
I bought new Maxtor HD 80 GB but somthing Fedora Core 3 crashes giving this message:
hda:
dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda:dma_intr: Error=0x84 { DriveStatusError BadCRC }How can I solve it ?
Check your hardware. ATA cables must not exceed 45 cm in length; for Ultra DMA 4, 5 or 6 (66 MByte/s and faster), you need to use 80-wire cables (they need extra ground lines for shielding), and check if all plugs are seated properly.
WRT the backtrace you showed, someone else will have to answer - which kernel version are you using? If it's a Fedora-patched kernel, report the problem to the Fedora project. If it's an older unmodified kernel, retry with a newer kernel (2.6.12.3) first and see if the problem is still present.
Signature · 1 line
Matthias Andree
I already used 80-wire cable and my Maxtor HD plugs are seated properly. My Kernel is 2.6.12-1.1372 on Fedora Core 3
HD is 80 GB Maxtor ATA/133
With hdparm command I can see hda is set in "udma5" mode, but why is'it not udma6 (133 Mhz) ? Can it be problem ?!
Sampei
Quoted 23 lines
-- Messaggio Originale --
Date: Fri, 22 Jul 2005 10:48:05 +0200
From: Matthias Andree <[email protected]>
To: [email protected]
Subject: Re: DriveStatusError BadCRCQuoted 1 line · On Fri, 22 Jul 2005, [email protected] wrote:
I bought new Maxtor HD 80 GB but somthing Fedora Core 3 crashes giving
this
Quoted 6 lines
message:
hda:
dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda:dma_intr: Error=0x84 { DriveStatusError BadCRC }How can I solve it ?
Check your hardware. ATA cables must not exceed 45 cm in length; for Ultra DMA 4, 5 or 6 (66 MByte/s and faster), you need to use 80-wire cables (they need extra ground lines for shielding), and check if all plugs are seated properly.
Quoted 10 lines
WRT the backtrace you showed, someone else will have to answer - which kernel version are you using? If it's a Fedora-patched kernel, report the problem to the Fedora project. If it's an older unmodified kernel, retry with a newer kernel (2.6.12.3) first and see if the problem is still present.
Signature · 3 lines
Matthias Andree - To unsubscribe from this list: send the line "unsubscribe linux-kernel"
in
Quoted 3 lines
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
__________________________________________________________________
TISCALI ADSL 1.25 MEGA
Solo con Tiscali Adsl navighi senza limiti e telefoni senza canone Telecom a partire da 19,95 Euro/mese.
Attivala entro il 28 luglio, il primo MESE è GRATIS! CLICCA QUI.
http://abbonati.tiscali.it/adsl/sa/1e25flat_tc/
Quoted 5 lines · On Gwe, 2005-07-22 at 11:16 +0200, [email protected] wrote:
I already used 80-wire cable and my Maxtor HD plugs are seated properly. My Kernel is 2.6.12-1.1372 on Fedora Core 3
HD is 80 GB Maxtor ATA/133
With hdparm command I can see hda is set in "udma5" mode, but why is'it not udma6 (133 Mhz) ? Can it be problem ?!
UDMA6 requires both the controller and drive can handle that speed. A lot of common controllers only handle UDMA5.
Quoted 8 lines
I bought new Maxtor HD 80 GB but somthing Fedora Core 3 crashes giving this message:
hda:dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda:dma_intr: Error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hda:dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda:dma_intr: Error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
Does this happen on boot?
Check your harddrive... smartctl -data -a /dev/hda and look for
199 UDMA_CRC_Error_Count 0x0008 198 193 000 Old_age Offline -
and
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 38 2f 8f 07 e4 08 43d+13:12:02.304 READ DMA
Jan Engelhardt
I run this command and I obtained:
smartctl version 5.33 [i386-redhat-linux-gnu] Copyright (C) 2002-4 Bruce Allen
Home page is http://smartmontools.sourceforge.net/
=== START OF INFORMATION SECTION ===
Device Model: Maxtor 6Y080L0 Serial Number: Y23TZR2C Firmware Version: YAR41BW0 User Capacity: 81,964,302,336 bytes Device is: In smartctl database [for details use: -P show] ATA Version is: 7 ATA Standard is: ATA/ATAPI-7 T13 1532D revision 0 Local Time is: Fri Jul 22 11:46:20 2005 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION ===
SMART overall-health self-assessment test result: PASSED
General SMART Values:
Offline data collection status: (0x80) Offline data collection activity
was never started.
Auto Offline Data Collection: Enabled.
Self-test execution status: ( 0) The previous self-test routine completed
without error or no self-test has ever been run.
Total time to complete Offline
data collection: ( 241) seconds.
Offline data collection
capabilities: (0x5b) SMART execute Offline immediate.
Auto Offline data collection on/off support. Suspend Offline collection upon new command.
Offline surface scan supported. Self-test supported.
No Conveyance Self-test supported. Selective Self-test supported.
SMART capabilities: (0x0003) Saves SMART data before entering
power-saving mode.
Supports SMART auto save timer.
Error logging capability: (0x01) Error logging supported.
No General Purpose Logging support.
Short self-test routine
recommended polling time: ( 2) minutes.
Extended self-test routine
recommended polling time: ( 37) minutes.
SMART Attributes Data Structure revision number: 16 Vendor Specific SMART Attributes with Thresholds:
ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED
WHEN_FAILED RAW_VALUE
3 Spin_Up_Time 0x0027 252 252 063 Pre-fail Always
- 323
4 Start_Stop_Count 0x0032 253 253 000 Old_age Always
- 3
5 Reallocated_Sector_Ct 0x0033 253 253 063 Pre-fail Always
- 1
6 Read_Channel_Margin 0x0001 253 253 100 Pre-fail Offline
- 0
7 Seek_Error_Rate 0x000a 253 252 000 Old_age Always
- 0
8 Seek_Time_Performance 0x0027 251 245 187 Pre-fail Always
- 37971
9 Power_On_Minutes 0x0032 253 253 000 Old_age Always
- 95h+25m
10 Spin_Retry_Count 0x002b 252 252 157 Pre-fail Always
- 0
11 Calibration_Retry_Count 0x002b 252 252 223 Pre-fail Always
- 0
12 Power_Cycle_Count 0x0032 253 253 000 Old_age Always
- 9
192 Power-Off_Retract_Count 0x0032 253 253 000 Old_age Always
- 0
193 Load_Cycle_Count 0x0032 253 253 000 Old_age Always
- 0
194 Temperature_Celsius 0x0032 253 253 000 Old_age Always
- 38
195 Hardware_ECC_Recovered 0x000a 253 252 000 Old_age Always
- 949
196 Reallocated_Event_Count 0x0008 253 253 000 Old_age Offline
- 0
197 Current_Pending_Sector 0x0008 253 253 000 Old_age Offline
- 0
198 Offline_Uncorrectable 0x0008 253 253 000 Old_age Offline
- 0
199 UDMA_CRC_Error_Count 0x0008 183 174 000 Old_age Offline
- 30
200 Multi_Zone_Error_Rate 0x000a 253 252 000 Old_age Always
- 0
201 Soft_Read_Error_Rate 0x000a 253 233 000 Old_age Always
- 75
202 TA_Increase_Count 0x000a 253 252 000 Old_age Always
- 0
203 Run_Out_Cancel 0x000b 253 252 180 Pre-fail Always
- 0
204 Shock_Count_Write_Opern 0x000a 253 252 000 Old_age Always
- 0
205 Shock_Rate_Write_Opern 0x000a 253 252 000 Old_age Always
- 0
207 Spin_High_Current 0x002a 252 252 000 Old_age Always
- 0
208 Spin_Buzz 0x002a 252 252 000 Old_age Always
- 0
209 Offline_Seek_Performnce 0x0024 196 196 000 Old_age Offline
- 0
99 Unknown_Attribute 0x0004 253 253 000 Old_age Offline
- 0
100 Unknown_Attribute 0x0004 253 253 000 Old_age Offline
- 0
101 Unknown_Attribute 0x0004 253 253 000 Old_age Offline
- 0
SMART Error Log Version: 1
Warning: ATA error count 46 inconsistent with error log pointer 5
ATA Error Count: 46 (device log contains only the most recent five errors)
CR = Command Register [HEX]
FR = Features Register [HEX]
SC = Sector Count Register [HEX]
SN = Sector Number Register [HEX]
CL = Cylinder Low Register [HEX]
CH = Cylinder High Register [HEX]
DH = Device/Head Register [HEX]
DC = Device Command Register [HEX]
ER = Error register [HEX]
ST = Status register [HEX]Powered_Up_Time is measured from power on, and printed as DDd+hh:mm:SS.sss where DD=days, hh=hours, mm=minutes,
SS=sec, and sss=millisec. It "wraps" after 49.710 days.
Error 46 occurred at disk power-on lifetime: 89 hours (3 days + 17 hours)
When the command that caused the error occurred, the device was in an unknown
state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 c1 80 c9 2c e3 Error: ICRC, ABRT at LBA = 0x032cc980 = 53266816
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ca 00 00 41 c9 2c e3 08 00:37:40.848 WRITE DMA ca 00 00 41 c8 2c e3 08 00:37:40.832 WRITE DMA ca 00 08 29 39 43 e3 08 00:37:40.832 WRITE DMA ca 00 08 d9 33 43 e3 08 00:37:40.832 WRITE DMA ca 00 08 c9 33 43 e3 08 00:37:40.832 WRITE DMA
Error 45 occurred at disk power-on lifetime: 89 hours (3 days + 17 hours)
When the command that caused the error occurred, the device was in an unknown
state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 00 39 8d 2c e3 Error: ICRC, ABRT at LBA = 0x032c8d39 = 53251385
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ca 00 00 39 8d 2c e3 08 00:33:07.648 WRITE DMA ca 00 00 39 8c 2c e3 08 00:33:07.648 WRITE DMA c8 00 80 80 30 c9 e6 08 00:33:07.632 READ DMA ca 00 18 89 bf 40 e3 08 00:33:07.632 WRITE DMA ca 00 60 21 bf 40 e3 08 00:33:07.632 WRITE DMA
Error 44 occurred at disk power-on lifetime: 87 hours (3 days + 15 hours)
When the command that caused the error occurred, the device was in an unknown
state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 78 79 b9 2c e3 Error: ICRC, ABRT at LBA = 0x032cb979 = 53262713
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ca 00 b8 39 b9 2c e3 08 2d+06:26:20.352 WRITE DMA ca 00 b8 39 b9 2c e3 08 2d+06:26:20.288 WRITE DMA 10 00 ff 00 00 00 e0 08 2d+06:26:20.272 RECALIBRATE [OBS-4] ca 00 b8 39 b9 2c e3 08 2d+06:26:20.208 WRITE DMA ca 00 b8 39 b9 2c e3 08 2d+06:26:19.952 WRITE DMA
Error 43 occurred at disk power-on lifetime: 87 hours (3 days + 15 hours)
When the command that caused the error occurred, the device was in an unknown
state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 78 79 b9 2c e3 Error: ICRC, ABRT at LBA = 0x032cb979 = 53262713
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ca 00 b8 39 b9 2c e3 08 2d+06:26:20.288 WRITE DMA 10 00 ff 00 00 00 e0 08 2d+06:26:20.272 RECALIBRATE [OBS-4] ca 00 b8 39 b9 2c e3 08 2d+06:26:20.208 WRITE DMA ca 00 b8 39 b9 2c e3 08 2d+06:26:19.952 WRITE DMA ca 00 10 81 a6 31 e3 08 2d+06:26:19.952 WRITE DMA
Error 42 occurred at disk power-on lifetime: 87 hours (3 days + 15 hours)
When the command that caused the error occurred, the device was in an unknown
state.
After command completion occurred, registers were:
ER ST SC SN CL CH DH
-- -- -- -- -- -- --
84 51 78 79 b9 2c e3 Error: ICRC, ABRT at LBA = 0x032cb979 = 53262713
Commands leading to the command that caused the error were:
CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- ca 00 b8 39 b9 2c e3 08 2d+06:26:20.208 WRITE DMA ca 00 b8 39 b9 2c e3 08 2d+06:26:19.952 WRITE DMA ca 00 10 81 a6 31 e3 08 2d+06:26:19.952 WRITE DMA ca 00 08 91 a5 31 e3 08 2d+06:26:19.952 WRITE DMA ca 00 10 b1 a3 31 e3 08 2d+06:26:19.952 WRITE DMA
SMART Self-test log structure revision number 1
No self-tests have been logged. [To run self-tests, use: smartctl -t]
SMART Selective self-test log data structure revision number 1
SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS
1 0 0 Not_testing
2 0 0 Not_testing
3 0 0 Not_testing
4 0 0 Not_testing
5 0 0 Not_testingSelective self-test flags (0x0):
After scanning selected spans, do NOT read-scan remainder of disk.
If Selective self-test is pending on power-up, resume after 0 minute delay.
thanks
Quoted 9 lines
-- Messaggio Originale --
Date: Fri, 22 Jul 2005 11:34:55 +0200 (MEST)
From: Jan Engelhardt <[email protected]>
To: [email protected]
cc: [email protected]
Subject: Re: DriveStatusError BadCRCQuoted 1 line
I bought new Maxtor HD 80 GB but somthing Fedora Core 3 crashes giving
this
Quoted 21 lines
Quoted 7 lines
message:
hda:dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda:dma_intr: Error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hda:dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda:dma_intr: Error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknownDoes this happen on boot?
Check your harddrive... smartctl -data -a
/dev/hdaand look for
199UDMA_CRC_Error_Count0x0008198 193 000Old_ageOffline- and Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 38 2f 8f 07 e4 08 43d+13:12:02.304 READ DMA
Quoted 4 lines
Jan Engelhardt
Signature · 2 lines
- To unsubscribe from this list: send the line "unsubscribe linux-kernel"
in
Quoted 3 lines
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
__________________________________________________________________
TISCALI ADSL 1.25 MEGA
Solo con Tiscali Adsl navighi senza limiti e telefoni senza canone Telecom a partire da 19,95 Euro/mese.
Attivala entro il 28 luglio, il primo MESE è GRATIS! CLICCA QUI.
http://abbonati.tiscali.it/adsl/sa/1e25flat_tc/
This problem occurs in a variable time after boot. After few hours that pc is turned on.
Quoted 9 lines
-- Messaggio Originale --
Date: Fri, 22 Jul 2005 11:34:55 +0200 (MEST)
From: Jan Engelhardt <[email protected]>
To: [email protected]
cc: [email protected]
Subject: Re: DriveStatusError BadCRCQuoted 1 line
I bought new Maxtor HD 80 GB but somthing Fedora Core 3 crashes giving
this
Quoted 21 lines
Quoted 7 lines
message:
hda:dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda:dma_intr: Error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknown
hda:dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda:dma_intr: Error=0x84 { DriveStatusError BadCRC }
ide: failed opcode was: unknownDoes this happen on boot?
Check your harddrive... smartctl -data -a
/dev/hdaand look for
199UDMA_CRC_Error_Count0x0008198 193 000Old_ageOffline- and Commands leading to the command that caused the error were: CR FR SC SN CL CH DH DC Powered_Up_Time Command/Feature_Name -- -- -- -- -- -- -- -- ---------------- -------------------- c8 00 38 2f 8f 07 e4 08 43d+13:12:02.304 READ DMA
Quoted 4 lines
Jan Engelhardt
Signature · 2 lines
- To unsubscribe from this list: send the line "unsubscribe linux-kernel"
in
Quoted 3 lines
the body of a message to [email protected]
More majordomo info at http://vger.kernel.org/majordomo-info.html
Please read the FAQ at http://www.tux.org/lkml/
__________________________________________________________________
TISCALI ADSL 1.25 MEGA
Solo con Tiscali Adsl navighi senza limiti e telefoni senza canone Telecom a partire da 19,95 Euro/mese.
Attivala entro il 28 luglio, il primo MESE è GRATIS! CLICCA QUI.
http://abbonati.tiscali.it/adsl/sa/1e25flat_tc/
Quoted 8 lines · On Fri, 2005-07-22 at 10:27 +0200, [email protected] wrote:
I bought new Maxtor HD 80 GB but somthing Fedora Core 3 crashes giving this
message:
hda:
dma_intr: status=0x51 { DriveReady SeekComplete Error }
hda:dma_intr: Error=0x84 { DriveStatusError BadCRC }
BadCRC tells you that there was a transmission error over the cable between the disk and the controller. I'd recommend either trying a different cable or reseating the existing one (and making sure it isn't right over the cpu where it could overheat etc)