OOPS in raid10.c:1448 in vanilla 2.6.13.2

DISCUSSION Guus Houtzager 2 participants 3 messages Sep 20, 2005 – Sep 21, 2005 MD RAID

Share & tools

Guus Houtzager

author

2005-09-20 16:45 UTC #0 lore raw

Hi,

On a new server I've been playing with software raid10. It's a Supermicro 5014C-MT which has a P8SCT motherboard. It has a 4 port SATA backplane connected to the ICH6R southbridge.

Quoted 1 line

From Jeff Garzik's webpages I know that libata does not and will not

support hot swap on ICH6R, so if I trigger an OOPS while doing that, it's my problem. However, if I reset the machine after the oops, it oopses again when trying to resync the raiddevice with all disks present which I didn't expect and find very odd: I expected maybe an errormessage and at best a succesfull resync.

This is what I did (Debian Sarge install):

# mdadm --create /dev/md1 --level=10 --raid-devices=4 /dev/sd[abcd]2
(mdadm is version 1.9.0-4, new enough to support raid10)
And let it sync.
# mke2fs -j /dev/md1
# mount /dev/md1 /mnt
Then removed sdb from the server. It took a while, but sdb2 got marked
faulty. Gave messages like this in syslog (as I expected):
Sep 20 19:08:23 lorentz kernel: ata2: error occurred, port reset
Sep 20 19:08:23 lorentz kernel: ata2: status=0x01 { Error }
Sep 20 19:08:23 lorentz kernel: ata2: called with no error (01)!
Sep 20 19:08:23 lorentz kernel: SCSI error : <1 0 0 0> return code =
0x8000002
Sep 20 19:08:23 lorentz kernel: sdb: Current: sense key=0x3
Sep 20 19:08:23 lorentz kernel:     ASC=0xc ASCQ=0x2
Sep 20 19:08:23 lorentz kernel: end_request: I/O error, dev sdb, sector
3919610
Sep 20 19:08:23 lorentz kernel: raid10: Disk failure on sdb2, disabling
device.
Sep 20 19:08:23 lorentz kernel: ^IOperation continuing on 3 devices

Then removed sdc from the server. Also took a while, but sdc2 also got marked faulty.
Filesystem on /mnt stays usable during all this (slight hickup when a disk is removed, but keeps going)
Then reinserted sdc. To get it resynced I did:

# mdadm /dev/md1 -r /dev/sdc2
# mdadm /dev/md1 -a /dev/sdc2
And it happily resynced and made sdc2 healthy again.
Then removed sdd and sdd2 got marked faulty. Filesystem kept working.
So at that point I was happy. At that point I just wanted to readd both
disks and get on with installing the server. So I reinserted both disks
m, waited several minutes and did:
# mdadm /dev/md1 -r /dev/sdb2
# mdadm /dev/md1 -r /dev/sdd2
# mdadm /dev/md1 -a /dev/sdb2
# mdadm /dev/md1 -a /dev/sdd2
And then it OOPS-ed.
Sep 20 19:25:01 lorentz kernel: md: unbind<sdb2>
Sep 20 19:25:01 lorentz kernel: md: export_rdev(sdb2)
Sep 20 19:25:06 lorentz kernel: md: unbind<sdd2>
Sep 20 19:25:06 lorentz kernel: md: export_rdev(sdd2)
Sep 20 19:25:09 lorentz kernel: md: bind<sdb2>
Sep 20 19:25:09 lorentz kernel: RAID10 conf printout:
Sep 20 19:25:09 lorentz kernel:  --- wd:2 rd:4
Sep 20 19:25:09 lorentz kernel:  disk 0, wo:0, o:1, dev:sda2
Sep 20 19:25:09 lorentz kernel:  disk 1, wo:0, o:1, dev:sdc2
Sep 20 19:25:09 lorentz kernel:  disk 2, wo:1, o:1, dev:sdb2
Sep 20 19:25:09 lorentz kernel: md: syncing RAID array md1
Sep 20 19:25:09 lorentz kernel: md: minimum _guaranteed_ reconstruction
speed: 1000 KB/sec/disc.
Sep 20 19:25:09 lorentz kernel: md: using maximum available idle IO
bandwith (but not more than 200000 KB/sec) for reconstruction.
Sep 20 19:25:09 lorentz kernel: md: using 128k window, over a total of
979840 blocks.
Sep 20 19:25:09 lorentz kernel: ------------[ cut here ]------------
Sep 20 19:25:09 lorentz kernel: kernel BUG at drivers/md/raid10.c:1448!
Sep 20 19:25:09 lorentz kernel: invalid operand: 0000 [#1]
Sep 20 19:25:09 lorentz kernel: SMP
Sep 20 19:25:09 lorentz kernel: Modules linked in:
Sep 20 19:25:09 lorentz kernel: CPU:    1
Sep 20 19:25:09 lorentz kernel: EIP:    0060:[sync_request+780/2122]
Not tainted VLI
Sep 20 19:25:09 lorentz kernel: EFLAGS: 00010246   (2.6.13.2)
Sep 20 19:25:09 lorentz kernel: EIP is at sync_request+0x30c/0x84a
Sep 20 19:25:09 lorentz kernel: eax: 00000000   ebx: f75d9300   ecx:
00000018   edx: 00000002
Sep 20 19:25:09 lorentz kernel: esi: f7c63880   edi: f75d930c   ebp:
f7c5c120   esp: f4df5eb0
Sep 20 19:25:09 lorentz kernel: ds: 007b   es: 007b   ss: 0068
Sep 20 19:25:09 lorentz kernel: Process md1_resync (pid: 1479,
threadinfo=f4df5000 task=f74c2020)
Sep 20 19:25:09 lorentz kernel: Stack: f7c63880 f75d9300 00000002
00000000 00000010 00000000 00000080 00000000
Sep 20 19:25:09 lorentz kernel:        00000000 00000000 00000002
00000002 00000003 00000000 e3c2c626 f4df5f3c
Sep 20 19:25:09 lorentz kernel:        f4df5f64 00000000 00000000
00000000 00000000 00000000 f7c70000 c037e533
Sep 20 19:25:09 lorentz kernel: Call Trace:
Sep 20 19:25:09 lorentz kernel:  [md_do_sync+1370/1792] md_do_sync
+0x55a/0x700
Sep 20 19:25:09 lorentz kernel:  [complete+66/82] complete+0x42/0x52
Sep 20 19:25:09 lorentz kernel:  [md_thread+297/359] md_thread
+0x129/0x167
Sep 20 19:25:09 lorentz kernel:  [autoremove_wake_function+0/75]
autoremove_wake_function+0x0/0x4b
Sep 20 19:25:09 lorentz kernel:  [md_thread+0/359] md_thread+0x0/0x167
Sep 20 19:25:09 lorentz kernel:  [kernel_thread_helper+5/11]
kernel_thread_helper+0x5/0xb
Sep 20 19:25:09 lorentz kernel: Code: 00 8b 54 24 14 85 d2 0f 85 25 ff
ff ff 8b 44 24 18 2b 44 24 64 01 44 24 20 83 44 24 24 01 8b 4c 24 18 89
4c 24 64 e9 24 fd ff ff <0f> 0b a8 05 ff 19 46 c0 89 dd 8b 56 08 e9 b8
fe ff ff 8b 46 60
Sep 20 19:25:11 lorentz kernel:  <6>md: bind<sdd2>
Sep 20 19:25:41 lorentz kernel: md: unbind<sdd2>
Sep 20 19:25:41 lorentz kernel: md: export_rdev(sdd2)
Sep 20 19:25:56 lorentz kernel: md: cannot remove active disk sdb2 from
md1 ...

And then I resetted the machine with the reset switch.
But to my surprise it oopsed again on reboot when the machine tried to resync automatically. It looks like the same oops as above, but I included it just to be sure:

Sep 20 19:42:07 lorentz kernel: ------------[ cut here ]------------
Sep 20 19:42:07 lorentz kernel: kernel BUG at drivers/md/raid10.c:1448!
Sep 20 19:42:07 lorentz kernel: invalid operand: 0000 [#1]
Sep 20 19:42:07 lorentz kernel: SMP
Sep 20 19:42:07 lorentz kernel: Modules linked in:
Sep 20 19:42:07 lorentz kernel: CPU:    1
Sep 20 19:42:07 lorentz kernel: EIP:    0060:[sync_request+780/2122]
Not tainted VLI
Sep 20 19:42:07 lorentz kernel: EFLAGS: 00010246   (2.6.13.2)
Sep 20 19:42:07 lorentz kernel: EIP is at sync_request+0x30c/0x84a
Sep 20 19:42:07 lorentz kernel: eax: 00000000   ebx: f79bbc80   ecx:
00000018 edx: 00000002
Sep 20 19:42:07 lorentz kernel: esi: f7d13700   edi: f79bbc8c   ebp:
f7cd63a0 esp: c1a28eb0
Sep 20 19:42:07 lorentz kernel: ds: 007b   es: 007b   ss: 0068
Sep 20 19:42:07 lorentz kernel: Process md1_resync (pid: 883,
threadinfo=c1a28000 task=f7cdf020)
Sep 20 19:42:07 lorentz kernel: Stack: f7d13700 f79bbc80 00000002
00000000 00000010 00000000 00000080 00000000
Sep 20 19:42:07 lorentz kernel:        00000000 00000000 00000002
00000002 00000003 00000000 4335da26 c1a28f3c
Sep 20 19:42:07 lorentz kernel:        c1a28f64 00000000 00000000
00000000 00000000 00000000 f7ce2200 c037e533
Sep 20 19:42:07 lorentz kernel: Call Trace:
Sep 20 19:42:07 lorentz kernel:  [md_do_sync+1370/1792] md_do_sync
+0x55a/0x700
Sep 20 19:42:07 lorentz kernel:  [complete+66/82] complete+0x42/0x52
Sep 20 19:42:07 lorentz kernel:  [md_thread+297/359] md_thread
+0x129/0x167
Sep 20 19:42:07 lorentz kernel:  [autoremove_wake_function+0/75]
autoremove_wake_function+0x0/0x4b
Sep 20 19:42:07 lorentz kernel:  [md_thread+0/359] md_thread+0x0/0x167
Sep 20 19:42:07 lorentz kernel:  [kernel_thread_helper+5/11]
kernel_thread_helper+0x5/0xb
Sep 20 19:42:07 lorentz kernel: Code: 00 8b 54 24 14 85 d2 0f 85 25 ff

ff ff 8b
44 24 18 2b 44 24 64 01 44 24 20 83 44 24 24 01 8b 4c 24 18 89 4c 24 64 e9 24 fd ff ff <0f> 0b a8 05 ff 19 46 c0 89 dd 8b 56 08 e9 b8 fe ff ff 8b 46 60

So did I stumble on a bug here or did I just do something stupid? I haven't tried with a different kernel.
More information available on request.

Thanks!!

Regards,

Guus Houtzager

Signature · 3 lines

                              Luna.nl B.V.
                Puntegaalstraat 109 * 3024 EB Rotterdam
              T 010 7502000 * F 010 7502002 * www.luna.nl

Neil Brown

2005-09-21 08:30 UTC #1 lore raw

Quoted 3 lines · On Tuesday September 20, [email protected] wrote:

Hi,
On a new server I've been playing with software raid10.

...

Quoted 2 lines

Sep 20 19:25:09 lorentz kernel: ------------[ cut here ]------------
Sep 20 19:25:09 lorentz kernel: kernel BUG at drivers/md/raid10.c:1448!

This is fixed in 2.6.14-rc1. I've attached the two patches that resolves this and a related problem.

However I should point out that what you did was guaranteed to kill the array (though mdadm-2.1 should have been able to re-assemble it with --force):

Quoted 1 line

# mdadm --create /dev/md1 --level=10 --raid-devices=4 /dev/sd[abcd]2

Now the four slots are
sda2 sdb2 sdc2 sdd2

sda2 and sdb2 have the same data, as do sdc2 and sdd2

Quoted 3 lines

Sep 20 19:08:23 lorentz kernel: raid10: Disk failure on sdb2, disabling
device.
Sep 20 19:08:23 lorentz kernel: ^IOperation continuing on 3 devices

now you have
sda2 missing sdc2 sdd2

Quoted 3 lines

Then removed sdc from the server. Also took a while, but sdc2 also got marked faulty.

now
sda2 missing missing sdd2
all data is still safe.

Quoted 6 lines

Filesystem on /mnt stays usable during all this (slight hickup when a disk is removed, but keeps going)
Then reinserted sdc. To get it resynced I did:
# mdadm /dev/md1 -r /dev/sdc2
# mdadm /dev/md1 -a /dev/sdc2
And it happily resynced and made sdc2 healthy again.

now
sda2 sdc2 missing sdd2

note that sdc2 took the first empty slot.

Quoted 1 line

Then removed sdd and sdd2 got marked faulty.

Now
sda2 sdc2 missing missing

so you have lost half your data.

Quoted 1 line

Filesystem kept working.

This is a bit odd - it should have stopped working, but that depends on how hard you pushed the filesystem. It would have failed if you tried to read or write in the area covered by the 2 two devices.

Quoted 6 lines

So at that point I was happy. At that point I just wanted to readd both disks and get on with installing the server. So I reinserted both disks m, waited several minutes and did:
# mdadm /dev/md1 -r /dev/sdb2
# mdadm /dev/md1 -r /dev/sdd2
# mdadm /dev/md1 -a /dev/sdb2

now you have
sda2 sdc2 sdb2-not-sync missing

it tried to recover sdb2, but there was no-where to recover from. This caused the BUG. The patches cause this situation to simply abort the recovery rather than BUG.

NeilBrown

Status: ok

Fix raid10 assembly when too many devices are missing.

if you try to assemble an array with too many missing devices, raid10 will now reject the attempt, instead of allowing it.

Also check when hot-adding a drive and refuse the hot-add if the array is beyond hope.

Signed-off-by Neil Brown <[email protected]>

### Diffstat output

 ./drivers/md/raid10.c |   30 +++++++++++++++++++++++++++---
 1 file changed, 27 insertions(+), 3 deletions(-)

drivers/md/raid10.c~current~ renamed from drivers/md/raid10.c +27 -3

diff ./drivers/md/raid10.c~current~ ./drivers/md/raid10.c
@@ -906,6 +906,27 @@ static void close_sync(conf_t *conf)
 	conf->r10buf_pool = NULL;
 }
 
+/* check if there are enough drives for
+ * every block to appear on atleast one
+ */
+static int enough(conf_t *conf)
+{
+	int first = 0;
+
+	do {
+		int n = conf->copies;
+		int cnt = 0;
+		while (n--) {
+			if (conf->mirrors[first].rdev)
+				cnt++;
+			first = (first+1) % conf->raid_disks;
+		}
+		if (cnt == 0)
+			return 0;
+	} while (first != 0);
+	return 1;
+}
+
 static int raid10_spare_active(mddev_t *mddev)
 {
 	int i;

@@ -944,6 +965,8 @@ static int raid10_add_disk(mddev_t *mdde
 		 * very different from resync
 		 */
 		return 0;
+	if (!enough(conf))
+		return 0;
 
 	for (mirror=0; mirror < mddev->raid_disks; mirror++)
 		if ( !(p=conf->mirrors+mirror)->rdev) {

@@ -1684,9 +1707,10 @@ static int run(mddev_t *mddev)
 	init_waitqueue_head(&conf->wait_idle);
 	init_waitqueue_head(&conf->wait_resume);
 
-	if (!conf->working_disks) {
-		printk(KERN_ERR "raid10: no operational mirrors for %s\n",
-			mdname(mddev));
+	/* need to check that every block has at least one working mirror */
+	if (!enough(conf)) {
+		printk(KERN_ERR "raid10: not enough operational mirrors for %s\n",
+		       mdname(mddev));
 		goto out_free_conf;
 	}

Status: ok

Fix BUG when raid10 rebuilds without enough drives.

This shouldn't be a BUG. We should cope.

Signed-off-by Neil Brown <[email protected]>

### Diffstat output

 ./drivers/md/raid10.c |    8 +++++++-
 1 file changed, 7 insertions(+), 1 deletion(-)

drivers/md/raid10.c~current~ renamed from drivers/md/raid10.c +7 -1

diff ./drivers/md/raid10.c~current~ ./drivers/md/raid10.c
@@ -1474,7 +1474,13 @@ static sector_t sync_request(mddev_t *md
 					}
 				}
 				if (j == conf->copies) {
-					BUG();
+					/* Cannot recover, so abort the recovery */
+					put_buf(r10_bio);
+					r10_bio = rb2;
+					if (!test_and_set_bit(MD_RECOVERY_ERR, &mddev->recovery))
+						printk(KERN_INFO "raid10: %s: insufficient working devices for recovery.\n",
+						       mdname(mddev));
+					break;
 				}
 			}
 		if (biolist == NULL) {

Guus Houtzager

author

2005-09-21 09:42 UTC #2 lore raw

Hi,

First of all: thanks for the speedy reply! Both patches applied cleanly to 2.6.13.2 and work as expected. No more oops :) I hope these patches make it into the next stable release of the 2.6.13 branch.

On Wed, 2005-09-21 at 10:30 +0200, Neil Brown wrote:

<snip>

Quoted 11 lines

Quoted 6 lines
Filesystem on /mnt stays usable during all this (slight hickup when a disk is removed, but keeps going)
Then reinserted sdc. To get it resynced I did:
# mdadm /dev/md1 -r /dev/sdc2
# mdadm /dev/md1 -a /dev/sdc2
And it happily resynced and made sdc2 healthy again.
now
sda2 sdc2 missing sdd2
note that sdc2 took the first empty slot.

That's where I went wrong. I thought it would take it's "old" place again at the second empty slot.

Thanks again!

Regards,

Guus Houtzager

Signature · 3 lines

                              Luna.nl B.V.
                Puntegaalstraat 109 * 3024 EB Rotterdam
              T 010 7502000 * F 010 7502002 * www.luna.nl