initramfs for /dev/console with udev?
Hi,
If I understand Documentation/early-userspace/README correctly it should be possible to solve the "unable to open an initial console" problem by using a file like
dir /dev 0755 0 0
nod /dev/console 0600 0 0 c 5 1
nod /dev/null 0600 0 0 c 1 3
dir /root 0700 0 0
and let CONFIG_INITRAMFS_SOURCE point to that file. The gpio archive is built correctly with that, but my kernel doesn't seem to use it.
Is anything else needed to use an initrd, like a command line argument? My kernel boots from a nfs partition, so it sets nfsroot=...
As I still get the "unable to open an initial console" message it looks like the initramfs is not extracted, mounted or however that works.
Robert
Signature · 5 lines
Dipl.-Ing. Robert Schwebel | http://www.pengutronix.de
Pengutronix - Linux Solutions for Science and Industry
Handelsregister: Amtsgericht Hildesheim, HRA 2686
Hannoversche Str. 2, 31134 Hildesheim, Germany
Phone: +49-5121-206917-0 | Fax: +49-5121-206917-9Quoted 6 lines · Robert Schwebel
Hi,
If I understand
Documentation/early-userspace/READMEcorrectly it should be possible to solve the "unable to open an initial console" problem by using a file like
Quoted 7 lines
dir /dev 0755 0 0
nod/dev/console0600 0 0 c 5 1
nod/dev/null0600 0 0 c 1 3
dir /root 0700 0 0and let
CONFIG_INITRAMFS_SOURCEpoint to that file. The gpio archive is built correctly with that, but my kernel doesn't seem to use it.
1) You have no init in initramfs, so it goes ahead and mounts whatever root= points to over it. I'm guessing that's where it's looking for /dev/console from.
2) What's the directory /root for?
Quoted 2 lines
Is anything else needed to use an initrd, like a command line argument? My kernel boots from a nfs partition, so it sets nfsroot=...
Note that initramfs and initrd and very different things.
Quoted 4 lines
As I still get the "unable to open an initial console" message it looks like the initramfs is not extracted, mounted or however that works.
Robert
Rob
Quoted 11 lines · Rob Landley
Quoted 7 lines
dir /dev 0755 0 0
nod/dev/console0600 0 0 c 5 1
nod/dev/null0600 0 0 c 1 3
dir /root 0700 0 0and let
CONFIG_INITRAMFS_SOURCEpoint to that file. The gpio archive is built correctly with that, but my kernel doesn't seem to use it.1) You have no init in initramfs, so it goes ahead and mounts whatever root= points to over it. I'm guessing that's where it's looking for
/dev/consolefrom.
Hmm, I thought something like that. That means that I do need a complete klibc based early userspace, just to get these two device nodes? Seems like I'll have to do some deeper investigation of klibc; last time I looked it didn't even compile for ARCH=um.
Quoted 1 line
2) What's the directory /root for?
Just a relict from the default script; the first three lines should be enought. But it shouldn't matter.
Quoted 4 lines
Quoted 2 lines
Is anything else needed to use an initrd, like a command line argument? My kernel boots from a nfs partition, so it sets nfsroot=...
Note that initramfs and initrd and very different things.
Is there any other known possibility to get just these two device nodes in an automatic way? I'm trying to get rid of devfs, and udev works just fine. The only thing not solved yet is how to get the beast started without /dev/console and /dev/null. I don't want to create the nodes statically, because that's only possible with root permissions.
Some background: I'm building root filesystems for embedded systems with PTXdist; the user is able to build the whole thing without root permissions; either with a cross compiler and mount it via NFS or build a JFFS2 image, or, with one switch, build and run it with an uml kernel.
I also tried ndevfs, just to get these two nodes, but I didn't find out how to automatically mount it on boot yet.
Robert
Signature · 5 lines
Dipl.-Ing. Robert Schwebel | http://www.pengutronix.de
Pengutronix - Linux Solutions for Science and Industry
Handelsregister: Amtsgericht Hildesheim, HRA 2686
Hannoversche Str. 2, 31134 Hildesheim, Germany
Phone: +49-5121-206917-0 | Fax: +49-5121-206917-9Quoted 9 lines · Robert Schwebel
Quoted 8 lines · Rob Landley
Quoted 7 lines
dir /dev 0755 0 0
nod/dev/console0600 0 0 c 5 1
nod/dev/null0600 0 0 c 1 3
dir /root 0700 0 0and let
CONFIG_INITRAMFS_SOURCEpoint to that file. The gpio archive is built correctly with that, but my kernel doesn't seem to use it.
Quoted 6 lines
Quoted 3 lines
1) You have no init in initramfs, so it goes ahead and mounts whatever root= points to over it. I'm guessing that's where it's looking for
/dev/consolefrom.Hmm, I thought something like that. That means that I do need a complete klibc based early userspace, just to get these two device nodes?
No, you just need a statically linked init program. (Which can be a shell script using a statically linked shell. For testing purposes it can be statically linked against glibc, it'll just be a bloated pig.)
I have a /tools directory that builds uClibc executables. (Like Linux From Scratch Chapter 5: extract it as /tools, export PATH=/tools/bin:$PATH, and then build software as normal.) I can post that somewhere if you'd like, or you can extract it yourself out of my firmware linux build
(http://www.landley.net/code/firmware)...
The switch_root program in busybox is still being banged on (by me). I haven't quite worked out what to do about /dev/console yet. I'm thinking if it's not there, keep the one from initramfs, but haven't implemented that tweak yet...
You also have the option of putting a single static node (console) in the /dev directory you're going to overmount. It shouldn't hurt anything at present. And if nothing else, it'll confirm where it's trying to get the sucker from...
Quoted 3 lines
Seems
like I'll have to do some deeper investigation of klibc; last time I looked it didn't even compile for ARCH=um.
Klibc didn't, or the kernel didn't?
Quoted 8 lines
Quoted 1 line
2) What's the directory /root for?
Just a relict from the default script; the first three lines should be enought. But it shouldn't matter.
Quoted 3 lines
Quoted 2 lines
Is anything else needed to use an initrd, like a command line argument? My kernel boots from a nfs partition, so it sets nfsroot=...
Quoted 6 lines
Quoted 1 line
Note that initramfs and initrd and very different things.
Is there any other known possibility to get just these two device nodes in an automatic way?
From initramfs, you could try:
mount -t sysfs /sys /sys
CDEV=cat /sys/class/tty/console
mknod /dev/console c $(echo $CDEV | sed 's/:.*//') \
$(echo $CDEV | sed 's/.*://')
Bit of a chicken and egg problem if it refuses to run /init if it's not already there, though. We're heading towards fully dynamic devices, but not quite there yet...
Quoted 4 lines
I'm trying to get rid of devfs, and udev works just
fine. The only thing not solved yet is how to get the beast started without/dev/consoleand/dev/null. I don't want to create the nodes statically, because that's only possible with root permissions.
You don't need root access to make an initramfs configuration text file. :)
Quoted 4 lines
Some background: I'm building root filesystems for embedded systems with PTXdist; the user is able to build the whole thing without root permissions; either with a cross compiler and mount it via NFS or build a JFFS2 image, or, with one switch, build and run it with an uml kernel.
I did something like that, only from scratch:
http://www.landley.net/code/firmware
I'll probably release version 0.8.10 later today. (Still need to make an installer for the bootable version before I can call it 0.9...)
Quoted 2 lines
I also tried ndevfs, just to get these two nodes, but I didn't find out how to automatically mount it on boot yet.
Presumably, either via initramfs or from init/main.c
Quoted 1 line
Robert
Rob
Quoted 3 lines · Rob Landley
No, you just need a statically linked init program. (Which can be a shell script using a statically linked shell. For testing purposes it can be statically linked against glibc, it'll just be a bloated pig.)
I'll try that.
Quoted 4 lines
You also have the option of putting a single static node (console) in the /dev directory you're going to overmount. It shouldn't hurt anything at present. And if nothing else, it'll confirm where it's trying to get the sucker from...
Well, that only works with root permissions.
Quoted 5 lines
Quoted 3 lines
Seems
like I'll have to do some deeper investigation of klibc; last time I looked it didn't even compile for ARCH=um.Klibc didn't, or the kernel didn't?
The kernel works pretty good with 2.6.14; I can now do 'make world' in PTXdist and get a rootfs for the ARM and do 'make world NATIVE=1' and 'make run NATIVE=1' and the same thing builds for x86 and starts in a console. klibc didn't compile for ARCH=um.
Quoted 5 lines
Quoted 2 lines
Is there any other known possibility to get just these two device nodes in an automatic way?
From initramfs, you could try:
Quoted 8 lines
mount -t sysfs /sys /sys
CDEV=cat /sys/class/tty/console
mknod/dev/consolec $(echo $CDEV | sed 's/:.*//') \
$(echo $CDEV | sed 's/.*://')Bit of a chicken and egg problem if it refuses to run /init if it's not already there, though. We're heading towards fully dynamic devices, but not quite there yet...
All that means that I need some libc and tools linking against it (or static tools)...
Quoted 6 lines
Quoted 4 lines
I'm trying to get rid of devfs, and udev works just
fine. The only thing not solved yet is how to get the beast started without/dev/consoleand/dev/null. I don't want to create the nodes statically, because that's only possible with root permissions.You don't need root access to make an initramfs configuration text file. :)
That was the idea ;) But it seems that if I buy initramfs I'll have to buy doing the mknod and rootfs mounting stuff from early userspace as well...
Quoted 10 lines
Quoted 4 lines
Some background: I'm building root filesystems for embedded systems with PTXdist; the user is able to build the whole thing without root permissions; either with a cross compiler and mount it via NFS or build a JFFS2 image, or, with one switch, build and run it with an uml kernel.
I did something like that, only from scratch:
http://www.landley.net/code/firmwareI'll probably release version 0.8.10 later today. (Still need to make an installer for the bootable version before I can call it 0.9...)
I'll have a look :)
Thx,
Robert
Signature · 5 lines
Dipl.-Ing. Robert Schwebel | http://www.pengutronix.de
Pengutronix - Linux Solutions for Science and Industry
Handelsregister: Amtsgericht Hildesheim, HRA 2686
Hannoversche Str. 2, 31134 Hildesheim, Germany
Phone: +49-5121-206917-0 | Fax: +49-5121-206917-9Quoted 10 lines · Robert Schwebel
Quoted 5 lines
Quoted 3 lines
Seems
like I'll have to do some deeper investigation of klibc; last time I looked it didn't even compile for ARCH=um.Klibc didn't, or the kernel didn't?
The kernel works pretty good with 2.6.14; I can now do 'make world' in PTXdist and get a rootfs for the ARM and do 'make world NATIVE=1' and 'make run NATIVE=1' and the same thing builds for x86 and starts in a console. klibc didn't compile for ARCH=um.
I repeat my question: what is it that didn't compile, klibc or the kernel?
ARCH=um is an argument given to the kernel, yet because of an argument given
to the kernel build, klibc didn't compile? I'm confused. Were you
attempting to compile klibc under User Mode Linux, and the klibc build failed? Or do you mean the kernel is what didn't compile, when you attempted to link user mode linux kernel against klibc?
(Yes, I confuse easily sometimes...)
Quoted 10 lines
Quoted 10 lines
Quoted 2 lines
Is there any other known possibility to get just these two device nodes in an automatic way?
From initramfs, you could try:
mount -t sysfs /sys /sys
CDEV=cat /sys/class/tty/console
mknod/dev/consolec $(echo $CDEV | sed 's/:.*//') \
$(echo $CDEV | sed 's/.*://')
Quoted 6 lines
Quoted 3 lines
Bit of a chicken and egg problem if it refuses to run /init if it's not already there, though. We're heading towards fully dynamic devices, but not quite there yet...
All that means that I need some libc and tools linking against it (or static tools)...
Well, it means you have to work around the deficiency in glibc that "hello world" is 400k statically linked. This is a problem with glibc. That's why I use uClibc instead. (Full featured, you can build X and everything under it, and hello world is 7k statically linked, most of which is the iostream stuff. If you use write() instead, with -Os stripped and statically linked, it's 4.2k.)
Quoted 11 lines
Quoted 7 lines
Quoted 4 lines
I'm trying to get rid of devfs, and udev works just
fine. The only thing not solved yet is how to get the beast started without/dev/consoleand/dev/null. I don't want to create the nodes statically, because that's only possible with root permissions.You don't need root access to make an initramfs configuration text file. :)
That was the idea ;) But it seems that if I buy initramfs I'll have to buy doing the mknod and rootfs mounting stuff from early userspace as well...
I added switch_root to busybox, and I'm planning on adding a stripped down udev as well, since this is likely to be a common need. (Udev itself is already pretty small, but it requires fairly extensive configuration to get it to do anything, and wants to maintain a database.)
That said, for Firmware Linux, I'm working on a system that has the root partition (squashfs) appended to the kernel image. So the kernel command line will have an argument ala FIRMWARE=hda1:/path/to/firmware.img so it can find itself, and then chops out the "hda1" from the environment variable, finds that under /sys/block, does the appropriate mknod based on what that dev file says, and mounts the new root. This is a very small shell script. (The rest finds the firmware image, does an losetup -o $offset, mounts the loop device, and does the switch_root.)
Quoted 6 lines
Quoted 6 lines
Quoted 5 lines
Some background: I'm building root filesystems for embedded systems with PTXdist; the user is able to build the whole thing without root permissions; either with a cross compiler and mount it via NFS or build a JFFS2 image, or, with one switch, build and run it with an uml kernel.
Quoted 7 lines
Quoted 5 lines
I did something like that, only from scratch:
http://www.landley.net/code/firmwareI'll probably release version 0.8.10 later today. (Still need to make an installer for the bootable version before I can call it 0.9...)
I'll have a look :)
This morning I had it pointed out to me that it doesn't build an x86-64 version yet. In my defense, I haven't got that hardware. (I have qemu though. It's on my todo list...)
Quoted 3 lines
Thx,
Robert
Rob
Quoted 4 lines · Robert Schwebel
Quoted 1 line
[...] klibc didn't compile for ARCH=um.
I repeat my question: what is it that didn't compile, klibc or the kernel?
come on, dude -- how much clearer can he be?
- R.
Quoted 7 lines · Roland Dreier
Quoted 5 lines · Robert Schwebel
Quoted 1 line
[...] klibc didn't compile for ARCH=um.
I repeat my question: what is it that didn't compile, klibc or the kernel?
come on, dude -- how much clearer can he be?
How do you feed ARCH=um to klibc?
Rob
Quoted 7 lines · Roland Dreier
Quoted 5 lines · Robert Schwebel
Quoted 1 line
[...] klibc didn't compile for ARCH=um.
I repeat my question: what is it that didn't compile, klibc or the kernel?
come on, dude -- how much clearer can he be?
Ah, I see. The linux kernel headers you feed it were from a kernel compiled with ARCH=um. Right. It's been a while since I tried feeding any libc actual kernel headers. (I build uClibc against the cleaned up userspace ones
here: http://ep09.pld-linux.org/~mmazur/linux-libc-headers/ .)
It's also been a while since I played with klibc, and I notice that it doesn't work with Maszur's headers. (It sort of works, with lots of warnings, until about halfway through when it wants to touch "asm/signal.h", when Maszur's just has linux/signal.h, and symlinking the two still isn't happy because sigset_t is never defined... In klibc there's definitions for ia64, sparc, and parisc. But nothing for x86...
Ok, checking 2.6.14/include/asm-i386 it's an unsigned long, so typedef that... Nope, still not happy, wants numerous other symbols now... Okay, try grabbing asm-i386/signal.h from libc... And asm-generic/signal.h which _that_ includes... And now there's a "previous declaration of 'wait3"' conflicting. Beautiful...)
Ok, I remember why I stopped playing with klibc now. It's still deep in alpha-test stage, requires way more incestuous knowledge of the kernel headers than anything not bundled with the kernel itself has any excuse for, and I'm still not sure what advantage it claims to have over uClibc except for being BSD licensed.
If you have to make it work, I'd suggest extracting a fresh kernel tarball, do "make allyesconfig" (without ARCH=um), and use _those_ headers. Or just accept that it doesn't work and try uClibc. :)
Rob
Quoted 27 lines · Rob Landley
Quoted 7 lines · Roland Dreier
Quoted 5 lines · Robert Schwebel
Quoted 1 line
[...] klibc didn't compile for ARCH=um.
I repeat my question: what is it that didn't compile, klibc or the kernel?
come on, dude -- how much clearer can he be?
Ah, I see. The linux kernel headers you feed it were from a kernel compiled with ARCH=um. Right. It's been a while since I tried feeding any libc actual kernel headers. (I build uClibc against the cleaned up userspace ones
here: http://ep09.pld-linux.org/~mmazur/linux-libc-headers/ .)It's also been a while since I played with klibc, and I notice that it doesn't work with Maszur's headers. (It sort of works, with lots of warnings, until about halfway through when it wants to touch "
asm/signal.h", when Maszur's just haslinux/signal.h, and symlinking the two still isn't happy becausesigset_tis never defined... In klibc there's definitions for ia64, sparc, and parisc. But nothing for x86...Ok, checking 2.6.14/include/asm-i386 it's an unsigned long, so typedef that... Nope, still not happy, wants numerous other symbols now... Okay, try grabbing
asm-i386/signal.hfrom libc... Andasm-generic/signal.hwhich _that_ includes... And now there's a "previous declaration of 'wait3"' conflicting. Beautiful...)
Quoted 6 lines
Ok, I remember why I stopped playing with klibc now. It's still deep in alpha-test stage, requires way more incestuous knowledge of the kernel headers than anything not bundled with the kernel itself has any excuse for, and I'm still not sure what advantage it claims to have over uClibc except for being BSD licensed.
Well, apparently the plan is to eventually bundle it with the kernel if not mistaken. Also, it have seen a stable release, and it works well for what it was intended for, and still have a less footprint than uClibc if space is really an issue.
Quoted 4 lines
If you have to make it work, I'd suggest extracting a fresh kernel tarball, do "make allyesconfig" (without ARCH=um), and use _those_ headers. Or just accept that it doesn't work and try uClibc. :)
It does work, just need to be fixed up for ARCH=um compiled kernel. I did a quick hack to do this, but HPA don't like it (and I do not blame him). Can be found here:
http://bugs.gentoo.org/attachment.cgi?id=67478
Signature · 1 line
Martin Schlemmer
Quoted 10 lines · Martin Schlemmer
Quoted 5 lines
Ok, I remember why I stopped playing with klibc now. It's still deep in alpha-test stage, requires way more incestuous knowledge of the kernel headers than anything not bundled with the kernel itself has any excuse for, and I'm still not sure what advantage it claims to have over uClibc except for being BSD licensed.
Well, apparently the plan is to eventually bundle it with the kernel if not mistaken. Also, it have seen a stable release, and it works well for what it was intended for, and still have a less footprint than uClibc if space is really an issue.
*shrug*. It only does static linking and uClibc can static link too. But there are no plans to bundle uClibc with the kernel. :)
Quoted 9 lines
Quoted 3 lines
If you have to make it work, I'd suggest extracting a fresh kernel tarball, do "make allyesconfig" (without ARCH=um), and use _those_ headers. Or just accept that it doesn't work and try uClibc. :)
It does work, just need to be fixed up for ARCH=um compiled kernel. I did a quick hack to do this, but HPA don't like it (and I do not blame him). Can be found here:
And apparently one of the goals of the 2.6.14 release (or one of the dot releases after it) is working with klibc, so I'll wander back to playing with uClibc...
Rob
Quoted 1 line · Rob Landley
And apparently one of the goals of the 2.6.14 release (or one of the dot
Of Mazur's header files...
Rob
Quoted 7 lines · Rob Landley
Quoted 6 lines · Martin Schlemmer
Quoted 5 lines
Ok, I remember why I stopped playing with klibc now. It's still deep in alpha-test stage, requires way more incestuous knowledge of the kernel headers than anything not bundled with the kernel itself has any excuse for, and I'm still not sure what advantage it claims to have over uClibc except for being BSD licensed.
Quoted 8 lines
Quoted 4 lines
Well, apparently the plan is to eventually bundle it with the kernel if not mistaken. Also, it have seen a stable release, and it works well for what it was intended for, and still have a less footprint than uClibc if space is really an issue.
*shrug*. It only does static linking and uClibc can static link too. But there are no plans to bundle uClibc with the kernel. :)
It can link dynamic ...
-----
$ readelf -a /usr/lib64/klibc/bin/sh | grep -2 INTERP | tail -n 3
INTERP 0x0000000000000190 0x0000000000400190 0x0000000000400190
0x000000000000002a 0x000000000000002a R 1
[Requesting program interpreter: /lib/klibc-zbHWOqxodx0Aind6t75AzMTNE9c.so]
-----Signature · 1 line
Martin Schlemmer
Quoted 4 lines · Martin Schlemmer
Quoted 2 lines
*shrug*. It only does static linking and uClibc can static link too. But there are no plans to bundle uClibc with the kernel. :)
It can link dynamic ...
Cool. As I said, been a while...
Rob
Quoted 7 lines · Roland Dreier
Quoted 5 lines · Robert Schwebel
Quoted 1 line
[...] klibc didn't compile for ARCH=um.
I repeat my question: what is it that didn't compile, klibc or the kernel?
come on, dude -- how much clearer can he be?
And confirming:
cd ~
tar xvjf linux-2.6.14.tar.bz2
cd linux-2.6.14
make allyesconfig
cd ~
tar xvzf klibc-1.1.tar.gz
cd klibc-1.1
ln -s ~/linux-2.6.14/include/asm-i386 include/asm ln -s ~/linux-2.6.14/include/asm-generic/ include/asm-generic ln -s ~/linux-2.6.14/include/linux include/linux make
Does indeed build klibc.
I get the strong feeling klibc-1.1 should be called klibc-2.6.14, but oh well...
Rob