sungem: Make PM of PHYs more reliable
Subsystems (3)
PATCH 1/1 sungem: Make PM of PHYs more reliable
On my latest laptop, I've had occasional PHY dead on wakeup from sleep... the PHY would be totally unresponsive even to toggling the hard reset line until the machine is powered down... Looking closely at the code, I found some possible issues in the way we setup the MDIO lines during suspend along with slight divergences from what Darwin does when resetting it that may explain the problem. That patch change these and the problem appear to be gone for me at least... I also fixed an mdelay -> msleep while I was at it to the pmac feature code that is called when toggling the PHY reset line since sungem doesn't call it in an atomic context anymore.
---
Dave, please send to Linus if you are ok with it.
arch/powerpc/platforms/powermac/feature.c +2 -2
@@ -914,12 +914,12 @@MACIO_OUT8 (KL_GPIO_ETH_PHY_RESET ,KEYLARGO_GPIO_OUTPUT_ENABLE ); (void )MACIO_IN8 (KL_GPIO_ETH_PHY_RESET );UNLOCK (flags); -mdelay (10 ); +msleep (10 );LOCK (flags);MACIO_OUT8 (KL_GPIO_ETH_PHY_RESET ,/*KEYLARGO_GPIO_OUTPUT_ENABLE | */ KEYLARGO_GPIO_OUTOUT_DATA );UNLOCK (flags); -mdelay (10 ); +msleep (10 );return 0 ; }
drivers/net/sungem.c +17 -16
@@ -1662,27 +1662,28 @@if (gp->pdev->vendor ==PCI_VENDOR_ID_APPLE ) {int i; +u16 ctrl; -/* Those delay sucks, the HW seem to love them though, I'll -* serisouly consider breaking some locks here to be able -* to schedule instead -*/ -for (i =0 ; i <3 ; i++) {#ifdef CONFIG_PPC_PMAC -pmac_call_feature (PMAC_FTR_GMAC_PHY_RESET , gp->of_node,0 ,0 ); -msleep (20 ); +pmac_call_feature (PMAC_FTR_GMAC_PHY_RESET , gp->of_node,0 ,0 );#endif -/* Some PHYs used by apple have problem getting back to us, -* we do an additional reset here -*/ -phy_write (gp,MII_BMCR ,BMCR_RESET ); -msleep (20 ); -if (phy_read (gp,MII_BMCR ) !=0xffff ) + +/* Some PHYs used by apple have problem getting back +* to us, we do an additional reset here +*/ +phy_write (gp,MII_BMCR ,BMCR_RESET ); +for (i =0 ; i <10 ; i++) { +if ((phy_read (gp,MII_BMCR ) &BMCR_RESET ) ==0 )break ; -if (i ==2 ) -printk (KERN_WARNING "%s: GMAC PHY not responding !\n" , - gp->dev->name); +msleep (10 ); } +if (i ==10 ) +printk (KERN_WARNING "%s: GMAC PHY not responding !\n" , + gp->dev->name); +/* Make sure isolate is off */ + ctrl =phy_read (gp,MII_BMCR ); +if (ctrl &BMCR_ISOLATE ) +phy_write (gp,MII_BMCR , ctrl & ~BMCR_ISOLATE ); } if (gp->pdev->vendor == PCI_VENDOR_ID_SUN &&
Quoted 11 lines · Benjamin Herrenschmidt
On my latest laptop, I've had occasional PHY dead on wakeup from sleep... the PHY would be totally unresponsive even to toggling the hard reset line until the machine is powered down... Looking closely at the code, I found some possible issues in the way we setup the MDIO lines during suspend along with slight divergences from what Darwin does when resetting it that may explain the problem. That patch change these and the problem appear to be gone for me at least... I also fixed an mdelay -> msleep while I was at it to the pmac feature code that is called when toggling the PHY reset line since sungem doesn't call it in an atomic context anymore.
Quoted 2 lines
Signed-off-by Benjamin Herrenschmidt <[email protected]>---
Oops, -EWRONGPATCH... Sorry, please ignore it, I'll dig the right one...
Ben.