Collie battery status sensing code
Subsystems (2)
RFC 1/1 Collie battery status sensing code
Hi!
This is collie battery sensing code. It differs from sharpsl code a bit -- because it is dependend on ucb1x00, not on platform bus.
I guess I should reorganize #include's and remove #if 0-ed code. Anything else?
Pavel
arch/arm/mach-sa1100/collie_pm.c new file +324 -0
@@ -0,0 +1,324 @@ +/* +* Based on spitz_pm.c and sharp code. +* +* Copyright (C) 2001 SHARP +* Copyright 2005 Pavel Machek <[email protected]> +* +* Distribute under GPLv2. +*/ + +#include <linux/module.h> +#include <linux/stat.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/device.h> +#include <asm/apm.h> +#include <asm/irq.h> +#include <asm/mach-types.h> +#include <asm/hardware.h> +#include <asm/hardware/scoop.h> +#include <asm/dma.h> +#include <linux/platform_device.h> + +#include <asm/arch/collie.h> +#include "../mach-pxa/sharpsl.h" +#include "../drivers/mfd/ucb1x00.h" +#include <asm/mach/sharpsl_param.h> + +#ifdef CONFIG_MCP_UCB1200_TS +#error Battery interferes with touchscreen +#endif + +static struct ucb1x00 *ucb; + +#define ConvRevise (x) ( ( ad_revise * x ) / 652 ) +#define ADCtoPower (x) (( 330 * x * 2 ) / 1024 ) + +static int ad_revise =0 ; + +static void collie_charger_init (void ) +{ +int err; + +/* get ad revise */ +if (sharpsl_param.adadj !=-1 ) { + ad_revise = sharpsl_param.adadj; + }else { + ad_revise =0 ; + } + +/* Register interrupt handler. */ +if ((err =request_irq (COLLIE_IRQ_GPIO_AC_IN , sharpsl_ac_isr,SA_INTERRUPT , +"ACIN" , sharpsl_ac_isr))) { +printk ("Could not get irq %d.\n" ,COLLIE_IRQ_GPIO_AC_IN ); +return ; + } + +/* Register interrupt handler. */ +if ((err =request_irq (COLLIE_IRQ_GPIO_CO , sharpsl_chrg_full_isr,SA_INTERRUPT , +"CO" , sharpsl_chrg_full_isr))) { +free_irq (COLLIE_IRQ_GPIO_AC_IN , sharpsl_ac_isr); +printk ("Could not get irq %d.\n" ,COLLIE_IRQ_GPIO_CO ); +return ; + } + +if (!ucb) +printk (KERN_CRIT "ucb is null!\n" ); + +/* Set transition detect */ +ucb1x00_enable_irq (ucb,COLLIE_GPIO_AC_IN ,UCB_RISING ); +ucb1x00_enable_irq (ucb,COLLIE_GPIO_CO ,UCB_RISING ); + +ucb1x00_adc_enable (ucb); +ucb1x00_io_set_dir (ucb,0 ,COLLIE_TC35143_GPIO_MBAT_ON |COLLIE_TC35143_GPIO_TMP_ON | +COLLIE_TC35143_GPIO_BBAT_ON ); +return ; +} + +static void collie_charge_led (int val) +{ +if (val ==SHARPSL_LED_ERROR ) { +dev_dbg (sharpsl_pm.dev,"Charge LED Error\n" ); + }else if (val ==SHARPSL_LED_ON ) { +dev_dbg (sharpsl_pm.dev,"Charge LED On\n" ); + }else { +dev_dbg (sharpsl_pm.dev,"Charge LED Off\n" ); + } +} + +static void collie_measure_temp (int on) +{ +if (on) +ucb1x00_io_write (ucb,COLLIE_TC35143_GPIO_TMP_ON ,0 ); +else +ucb1x00_io_write (ucb,0 ,COLLIE_TC35143_GPIO_TMP_ON ); +} + +static void collie_charge (int on) +{ +if (on) { +printk ("Should start charger\n" ); + }else { +printk ("Should stop charger\n" ); + } +#ifdef I_AM_SURE +#define CF_BUF_CTRL_BASE 0xF0800000 +#define SCOOP_REG (adr) (*(volatile unsigned short*)(CF_BUF_CTRL_BASE+(adr))) +#define SCOOP_REG_GPWR SCOOP_REG(SCOOP_GPWR) + +if (on) { +SCOOP_REG_GPWR |=COLLIE_SCP_CHARGE_ON ; + }else { +SCOOP_REG_GPWR &= ~COLLIE_SCP_CHARGE_ON ; + } +#endif +} + +static void collie_discharge (int on) +{ +} + +static void collie_discharge1 (int on) +{ +} + +static void collie_presuspend (void ) +{ +} + +static void collie_postsuspend (void ) +{ +} + +static int collie_should_wakeup (unsigned int resume_on_alarm) +{ +return 0 ; +} + +static unsigned long collie_charger_wakeup (void ) +{ +return 0 ; +} + +static int collie_acin_status (void ) +{ +int ret =GPLR &COLLIE_GPIO_AC_IN ; +printk ("AC status = %d\n" , ret); +return ret; +} + +int collie_read_backup_battery (void ) +{ +int voltage; + +/* Gives 75..130 */ +ucb1x00_io_write (ucb,COLLIE_TC35143_GPIO_BBAT_ON ,0 ); + voltage =ucb1x00_adc_read (ucb,UCB_ADC_INP_AD1 ,UCB_SYNC ); + +ucb1x00_io_write (ucb,0 ,COLLIE_TC35143_GPIO_BBAT_ON ); + +printk ("Backup battery = %d(%d)\n" ,ADCtoPower (voltage), voltage); + +return ADCtoPower (voltage); +} + +int collie_read_main_battery (void ) +{ +int voltage; + +collie_read_temp (); +collie_read_backup_battery (); +ucb1x00_io_write (ucb,0 ,COLLIE_TC35143_GPIO_BBAT_ON ); +ucb1x00_io_write (ucb,COLLIE_TC35143_GPIO_MBAT_ON ,0 ); + voltage =ucb1x00_adc_read (ucb,UCB_ADC_INP_AD1 ,UCB_SYNC ); + +ucb1x00_io_write (ucb,0 ,COLLIE_TC35143_GPIO_MBAT_ON ); + +/* +gives values 160..255 with battery removed... and +145..255 with battery inserted. (on AC) + +On battery, it goes as low as 80. +*/ + +printk ("Main battery = %d(%d)\n" ,ADCtoPower ((voltage+ConvRevise (voltage))),voltage); + +if ( voltage !=-1 ) { +return ADCtoPower ((voltage+ConvRevise (voltage))); + }else { +return voltage; + } +} + +int collie_read_temp (void ) +{ +int voltage; + +/* temp must be > 973, main battery must be < 465 */ +/* FIXME sharpsl_pm.c has both conditions negated? */ + +ucb1x00_io_write (ucb,COLLIE_TC35143_GPIO_TMP_ON ,0 ); + voltage =ucb1x00_adc_read (ucb,UCB_ADC_INP_AD0 ,UCB_SYNC ); +ucb1x00_io_write (ucb,0 ,COLLIE_TC35143_GPIO_TMP_ON ); + +/* >1010 = battery removed. +460 = 22C ? +higer = lower temp ? +*/ + +printk ("Battery temp = %d\n" , voltage); +return voltage; +} + +static int collie_read_acin (void ) +{ +return 0x1 ; +} + +static unsigned long read_devdata (int which) +{ +switch (which) { +case SHARPSL_BATT_VOLT : +return collie_read_main_battery (); +case SHARPSL_BATT_TEMP : +return collie_read_temp (); +case SHARPSL_ACIN_VOLT : +return collie_read_acin (); +case SHARPSL_STATUS_ACIN : +case SHARPSL_STATUS_LOCK : +case SHARPSL_STATUS_CHRGFULL : +case SHARPSL_STATUS_FATAL : +default : +return ~0 ; + } +#if 0 +It should be okay. Nobody really needs those. + .gpio_batlock = COLLIE_GPIO_BAT_COVER, + .gpio_acin = COLLIE_GPIO_AC_IN, + .gpio_batfull = COLLIE_GPIO_CHRG_FULL, + .gpio_fatal = COLLIE_GPIO_FATAL_BAT, +#endif +} + +struct battery_thresh spitz_battery_levels_noac[] = { +#ifdef FOO_FRONTLIGHT + { 368, 100}, + { 358, 25}, + { 356, 5}, + { 0, 0}, +#else + { 378, 100}, + { 365, 25}, + { 363, 5}, + { 0, 0}, +#endif +}; + +struct battery_thresh spitz_battery_levels_acin[] = { +#ifdef FOO_FRONTLIGHT + { 368, 100}, + { 358, 25}, + { 356, 5}, + { 0, 0}, +#else + { 378, 100}, + { 365, 25}, + { 363, 5}, + { 0, 0}, +#endif +}; + +struct sharpsl_charger_machinfo collie_pm_machinfo = { + .init = collie_charger_init, + .read_devdata = read_devdata, + .discharge = collie_discharge, + .discharge1 = collie_discharge1, + .charge = collie_charge, + .measure_temp = collie_measure_temp, + .presuspend = collie_presuspend, + .postsuspend = collie_postsuspend, + .charger_wakeup = collie_charger_wakeup, + .should_wakeup = collie_should_wakeup, + .bat_levels = 3, + .bat_levels_noac = spitz_battery_levels_noac, + .bat_levels_acin = spitz_battery_levels_acin, + .status_high_acin = 368, + .status_low_acin = 358, + .status_high_noac = 368, + .status_low_noac = 358, +}; + +extern struct sharpsl_pm_status sharpsl_pm; + +static int __init collie_pm_add(struct ucb1x00_dev *pdev) +{ + sharpsl_pm.dev = NULL; + sharpsl_pm.machinfo = &collie_pm_machinfo; + ucb = pdev->ucb; + return sharpsl_pm_init(); +} + +static int collie_pm_remove(struct ucb1x00_dev *pdev) +{ + return sharpsl_pm_done(); +} + +static struct ucb1x00_driver collie_pm_driver = { + .add = collie_pm_add, + .remove = collie_pm_remove, +}; + +static int __init collie_pm_init(void) +{ + return ucb1x00_register_driver(&collie_pm_driver); +} + +static void __exit collie_pm_exit(void) +{ + ucb1x00_unregister_driver(&collie_pm_driver); +} + +late_initcall(collie_pm_init); +module_exit(collie_pm_exit);
Signature · 1 line
Web maintainer for suspend.sf.net (www.sf.net/projects/suspend) wanted...
Hi!
Quoted 5 lines
This is collie battery sensing code. It differs from sharpsl code a bit -- because it is dependend on ucb1x00, not on platform bus.
I guess I should reorganize #include's and remove #if 0-ed code. Anything else?
I cleaned it up a bit more. Anything left?
Pavel
arch/arm/mach-sa1100/collie_pm.c new file +254 -0
@@ -0,0 +1,254 @@ +/* +* Based on spitz_pm.c and sharp code. +* +* Copyright (C) 2001 SHARP +* Copyright 2005 Pavel Machek <[email protected]> +* +* Distribute under GPLv2. +*/ + +#include <linux/module.h> +#include <linux/stat.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/device.h> + +#include <asm/irq.h> +#include <asm/mach-types.h> +#include <asm/hardware.h> +#include <asm/hardware/scoop.h> +#include <asm/dma.h> +#include <asm/arch/collie.h> +#include <asm/mach/sharpsl_param.h> + +#include "../mach-pxa/sharpsl.h" +#include "../drivers/mfd/ucb1x00.h" + +static struct ucb1x00 *ucb; +static int ad_revise; + +#define ADCtoPower (x) ((330 * x * 2) / 1024) + +static void collie_charger_init (void ) +{ +int err; + +if (sharpsl_param.adadj !=-1 ) { + ad_revise = sharpsl_param.adadj; + } + +/* Register interrupt handler. */ +if ((err =request_irq (COLLIE_IRQ_GPIO_AC_IN , sharpsl_ac_isr,SA_INTERRUPT , +"ACIN" , sharpsl_ac_isr))) { +printk ("Could not get irq %d.\n" ,COLLIE_IRQ_GPIO_AC_IN ); +return ; + } +if ((err =request_irq (COLLIE_IRQ_GPIO_CO , sharpsl_chrg_full_isr,SA_INTERRUPT , +"CO" , sharpsl_chrg_full_isr))) { +free_irq (COLLIE_IRQ_GPIO_AC_IN , sharpsl_ac_isr); +printk ("Could not get irq %d.\n" ,COLLIE_IRQ_GPIO_CO ); +return ; + } + +/* Set transition detect */ +ucb1x00_enable_irq (ucb,COLLIE_GPIO_AC_IN ,UCB_RISING ); +ucb1x00_enable_irq (ucb,COLLIE_GPIO_CO ,UCB_RISING ); + +ucb1x00_adc_enable (ucb); +ucb1x00_io_set_dir (ucb,0 ,COLLIE_TC35143_GPIO_MBAT_ON |COLLIE_TC35143_GPIO_TMP_ON | +COLLIE_TC35143_GPIO_BBAT_ON ); +return ; +} + +static void collie_measure_temp (int on) +{ +if (on) +ucb1x00_io_write (ucb,COLLIE_TC35143_GPIO_TMP_ON ,0 ); +else +ucb1x00_io_write (ucb,0 ,COLLIE_TC35143_GPIO_TMP_ON ); +} + +static void collie_charge (int on) +{ +#ifdef I_AM_SURE +#define CF_BUF_CTRL_BASE 0xF0800000 +#define SCOOP_REG (adr) (*(volatile unsigned short*)(CF_BUF_CTRL_BASE+(adr))) +#define SCOOP_REG_GPWR SCOOP_REG(SCOOP_GPWR) + +if (on) { +SCOOP_REG_GPWR |=COLLIE_SCP_CHARGE_ON ; + }else { +SCOOP_REG_GPWR &= ~COLLIE_SCP_CHARGE_ON ; + } +#endif +} + +static void collie_discharge (int on) +{ +} + +static void collie_discharge1 (int on) +{ +} + +static void collie_presuspend (void ) +{ +} + +static void collie_postsuspend (void ) +{ +} + +static int collie_should_wakeup (unsigned int resume_on_alarm) +{ +return 0 ; +} + +static unsigned long collie_charger_wakeup (void ) +{ +return 0 ; +} + +int collie_read_backup_battery (void ) +{ +int voltage; + +ucb1x00_io_write (ucb,COLLIE_TC35143_GPIO_BBAT_ON ,0 ); + voltage =ucb1x00_adc_read (ucb,UCB_ADC_INP_AD1 ,UCB_SYNC ); + +ucb1x00_io_write (ucb,0 ,COLLIE_TC35143_GPIO_BBAT_ON ); + +printk ("Backup battery = %d(%d)\n" ,ADCtoPower (voltage), voltage); + +return ADCtoPower (voltage); +} + +int collie_read_main_battery (void ) +{ +int voltage, voltage_rev, voltage_volts; + +ucb1x00_io_write (ucb,0 ,COLLIE_TC35143_GPIO_BBAT_ON ); +ucb1x00_io_write (ucb,COLLIE_TC35143_GPIO_MBAT_ON ,0 ); + voltage =ucb1x00_adc_read (ucb,UCB_ADC_INP_AD1 ,UCB_SYNC ); + +ucb1x00_io_write (ucb,0 ,COLLIE_TC35143_GPIO_MBAT_ON ); + + voltage_rev = voltage + ((ad_revise * voltage) /652 ); + voltage_volts =ADCtoPower (voltage_rev); + +printk ("Main battery = %d(%d)\n" , voltage_volts, voltage); + +if ( voltage !=-1 ) { +return voltage_volts; + }else { +return voltage; + } +} + +int collie_read_temp (void ) +{ +int voltage; + +/* temp must be > 973, main battery must be < 465 */ +/* FIXME sharpsl_pm.c has both conditions negated? */ + +ucb1x00_io_write (ucb,COLLIE_TC35143_GPIO_TMP_ON ,0 ); + voltage =ucb1x00_adc_read (ucb,UCB_ADC_INP_AD0 ,UCB_SYNC ); +ucb1x00_io_write (ucb,0 ,COLLIE_TC35143_GPIO_TMP_ON ); + +printk ("Battery temp = %d\n" , voltage); +return voltage; +} + +static unsigned long read_devdata (int which) +{ +switch (which) { +case SHARPSL_BATT_VOLT : +return collie_read_main_battery (); +case SHARPSL_BATT_TEMP : +return collie_read_temp (); +case SHARPSL_ACIN_VOLT : +return 0x1 ; +case SHARPSL_STATUS_ACIN : { +int ret =GPLR &COLLIE_GPIO_AC_IN ; +printk ("AC status = %d\n" , ret); +return ret; + } +case SHARPSL_STATUS_FATAL : { +int ret =GPLR &COLLIE_GPIO_MAIN_BAT_LOW ; +printk ("Fatal bat = %d\n" , ret); +return ret; + } +default : +return ~0 ; + } +} + +struct battery_thresh spitz_battery_levels_noac[] = { + {368 ,100 }, + {358 ,25 }, + {356 ,5 }, + {0 ,0 }, +}; + +struct battery_thresh spitz_battery_levels_acin[] = { + {378 ,100 }, + {365 ,25 }, + {363 ,5 }, + {0 ,0 }, +}; + +struct sharpsl_charger_machinfo collie_pm_machinfo = { + .init = collie_charger_init, + .read_devdata = read_devdata, + .discharge = collie_discharge, + .discharge1 = collie_discharge1, + .charge = collie_charge, + .measure_temp = collie_measure_temp, + .presuspend = collie_presuspend, + .postsuspend = collie_postsuspend, + .charger_wakeup = collie_charger_wakeup, + .should_wakeup = collie_should_wakeup, + .bat_levels =3 , + .bat_levels_noac = spitz_battery_levels_noac, + .bat_levels_acin = spitz_battery_levels_acin, + .status_high_acin =368 , + .status_low_acin =358 , + .status_high_noac =368 , + .status_low_noac =358 , +}; + +extern struct sharpsl_pm_status sharpsl_pm; + +static int __init collie_pm_add (struct ucb1x00_dev *pdev) +{ + sharpsl_pm.dev =NULL ; + sharpsl_pm.machinfo = &collie_pm_machinfo; + ucb = pdev->ucb; +return sharpsl_pm_init (); +} + +static void collie_pm_remove (struct ucb1x00_dev *pdev) +{ +sharpsl_pm_done (); +} + +static struct ucb1x00_driver collie_pm_driver = { + .add = collie_pm_add, + .remove = collie_pm_remove, +}; + +static int __init collie_pm_init (void ) +{ +return ucb1x00_register_driver (&collie_pm_driver); +} + +static void __exit collie_pm_exit(void) +{ +ucb1x00_unregister_driver (&collie_pm_driver); +} + +late_initcall (collie_pm_init); +module_exit (collie_pm_exit);
Signature · 1 line
Web maintainer for suspend.sf.net (www.sf.net/projects/suspend) wanted...
Quoted 7 lines · Pavel Machek
Hi!
This is collie battery sensing code. It differs from sharpsl code a bit -- because it is dependend on ucb1x00, not on platform bus.
I guess I should reorganize #include's and remove #if 0-ed code. Anything else
Basically looks good. Could probably use a s/printk/dev_dbg(sharpsl_pm.dev, /. I've made a few other comments below.
Just for my interest, can you summarise the status of PM and charging on collie with this code?
Quoted 22 lines
arch/arm/mach-sa1100/collie_pm.c new file +16
-0@@ -0,0 +1,324 @@ +/* +* Based on spitz_pm.c and sharp code. +* +* Copyright (C) 2001 SHARP +* Copyright 2005 Pavel Machek <[email protected]> +* +* Distribute under GPLv2. +*/ + +#include <linux/module.h> +#include <linux/stat.h> +#include <linux/init.h> +#include <linux/kernel.h> +#include <linux/delay.h> +#include <linux/interrupt.h> +#include <linux/device.h>
arch/arm/mach-sa1100/collie_pm.c line 26
Quoted 10 lines
arch/arm/mach-sa1100/collie_pm.c new file +10
-0+#include <asm/apm.h> +#include <asm/irq.h> +#include <asm/mach-types.h> +#include <asm/hardware.h> +#include <asm/hardware/scoop.h> +#include <asm/dma.h> +#include <linux/platform_device.h> + +#include <asm/arch/collie.h> +#include "../mach-pxa/sharpsl.h"
Do you need anything in the above header? If so, it should probably be in asm/hardware/sharpsl_pm.h
arch/arm/mach-sa1100/collie_pm.c line 32
Quoted 6 lines
arch/arm/mach-sa1100/collie_pm.c new file +6
-0+#include "../drivers/mfd/ucb1x00.h" +#include <asm/mach/sharpsl_param.h> + +#ifdef CONFIG_MCP_UCB1200_TS +#error Battery interferes with touchscreen +#endif
Is this a case of bad locking or something more serious?
arch/arm/mach-sa1100/collie_pm.c line 39
Quoted 6 lines
arch/arm/mach-sa1100/collie_pm.c new file +6
-0+static struct ucb1x00 *ucb; + +#define ConvRevise (x) ( ( ad_revise * x ) / 652 ) +#define ADCtoPower (x) (( 330 * x * 2 ) / 1024 ) + +static int ad_revise =0 ;
The = 0 is unneeded.
arch/arm/mach-sa1100/collie_pm.c line 50
Quoted 10 lines
arch/arm/mach-sa1100/collie_pm.c new file +10
-0+static void collie_charger_init (void ) +{ +int err; + +/* get ad revise */ +if (sharpsl_param.adadj !=-1 ) { + ad_revise = sharpsl_param.adadj; + }else { + ad_revise =0 ; + }
ad_revise is already 0...
Quoted 8 lines
arch/arm/mach-sa1100/collie_pm.c new file +8
-0+ +/* Register interrupt handler. */ +if ((err =request_irq (COLLIE_IRQ_GPIO_AC_IN , sharpsl_ac_isr,SA_INTERRUPT , +"ACIN" , sharpsl_ac_isr))) { +printk ("Could not get irq %d.\n" ,COLLIE_IRQ_GPIO_AC_IN ); +return ; + } +
arch/arm/mach-sa1100/collie_pm.c line 68
Quoted 10 lines
arch/arm/mach-sa1100/collie_pm.c new file +10
-0+/* Register interrupt handler. */ +if ((err =request_irq (COLLIE_IRQ_GPIO_CO , sharpsl_chrg_full_isr,SA_INTERRUPT , +"CO" , sharpsl_chrg_full_isr))) { +free_irq (COLLIE_IRQ_GPIO_AC_IN , sharpsl_ac_isr); +printk ("Could not get irq %d.\n" ,COLLIE_IRQ_GPIO_CO ); +return ; + } + +if (!ucb) +printk (KERN_CRIT "ucb is null!\n" );
Should it return here? Given this, We might need to think about error handling in the init function.
Quoted 10 lines
arch/arm/mach-sa1100/collie_pm.c new file +10
-0+/* Set transition detect */ +ucb1x00_enable_irq (ucb,COLLIE_GPIO_AC_IN ,UCB_RISING ); +ucb1x00_enable_irq (ucb,COLLIE_GPIO_CO ,UCB_RISING ); + +ucb1x00_adc_enable (ucb); +ucb1x00_io_set_dir (ucb,0 ,COLLIE_TC35143_GPIO_MBAT_ON |COLLIE_TC35143_GPIO_TMP_ON | +COLLIE_TC35143_GPIO_BBAT_ON ); +return ; +} +
arch/arm/mach-sa1100/collie_pm.c line 89
Quoted 10 lines
arch/arm/mach-sa1100/collie_pm.c new file +10
-0+static void collie_charge_led (int val) +{ +if (val ==SHARPSL_LED_ERROR ) { +dev_dbg (sharpsl_pm.dev,"Charge LED Error\n" ); + }else if (val ==SHARPSL_LED_ON ) { +dev_dbg (sharpsl_pm.dev,"Charge LED On\n" ); + }else { +dev_dbg (sharpsl_pm.dev,"Charge LED Off\n" ); + } +}
For reference, we can move this into the core if the LED subsystem is accepted into mainline as we'll just need a platform independent trigger.
arch/arm/mach-sa1100/collie_pm.c line 105
Quoted 7 lines
arch/arm/mach-sa1100/collie_pm.c new file +7
-0+static void collie_charge (int on) +{ +if (on) { +printk ("Should start charger\n" ); + }else { +printk ("Should stop charger\n" ); + }
This can be removed before mainline?
arch/arm/mach-sa1100/collie_pm.c line 114
Quoted 9 lines
arch/arm/mach-sa1100/collie_pm.c new file +9
-0+#ifdef I_AM_SURE +#define CF_BUF_CTRL_BASE 0xF0800000 +#define SCOOP_REG (adr) (*(volatile unsigned short*)(CF_BUF_CTRL_BASE+(adr))) +#define SCOOP_REG_GPWR SCOOP_REG(SCOOP_GPWR) + +if (on) { +SCOOP_REG_GPWR |=COLLIE_SCP_CHARGE_ON ; + }else { +SCOOP_REG_GPWR &= ~COLLIE_SCP_CHARGE_ON ;
Ick. Use arch/arm/common/scoop.c to do this. Something like:
#include <asm/hardware/scoop.h>
if (on) {
set_scoop_gpio(&colliescoop_device.dev, COLLIE_SCP_CHARGE_ON);
} else {
reset_scoop_gpio(&colliescoop_device.dev, COLLIE_SCP_CHARGE_ON);
}Quoted 176 lines
arch/arm/mach-sa1100/collie_pm.c new file +176
-0+#endif +} + +static void collie_discharge (int on) +{ +} + +static void collie_discharge1 (int on) +{ +} + +static void collie_presuspend (void ) +{ +} + +static void collie_postsuspend (void ) +{ +} + +static int collie_should_wakeup (unsigned int resume_on_alarm) +{ +return 0 ; +} + +static unsigned long collie_charger_wakeup (void ) +{ +return 0 ; +} + +static int collie_acin_status (void ) +{ +int ret =GPLR &COLLIE_GPIO_AC_IN ; +printk ("AC status = %d\n" , ret); +return ret; +} + +int collie_read_backup_battery (void ) +{ +int voltage; + +/* Gives 75..130 */ +ucb1x00_io_write (ucb,COLLIE_TC35143_GPIO_BBAT_ON ,0 ); + voltage =ucb1x00_adc_read (ucb,UCB_ADC_INP_AD1 ,UCB_SYNC ); + +ucb1x00_io_write (ucb,0 ,COLLIE_TC35143_GPIO_BBAT_ON ); + +printk ("Backup battery = %d(%d)\n" ,ADCtoPower (voltage), voltage); + +return ADCtoPower (voltage); +} + +int collie_read_main_battery (void ) +{ +int voltage; + +collie_read_temp (); +collie_read_backup_battery (); +ucb1x00_io_write (ucb,0 ,COLLIE_TC35143_GPIO_BBAT_ON ); +ucb1x00_io_write (ucb,COLLIE_TC35143_GPIO_MBAT_ON ,0 ); + voltage =ucb1x00_adc_read (ucb,UCB_ADC_INP_AD1 ,UCB_SYNC ); + +ucb1x00_io_write (ucb,0 ,COLLIE_TC35143_GPIO_MBAT_ON ); + +/* +gives values 160..255 with battery removed... and +145..255 with battery inserted. (on AC) + +On battery, it goes as low as 80. +*/ + +printk ("Main battery = %d(%d)\n" ,ADCtoPower ((voltage+ConvRevise (voltage))),voltage); + +if ( voltage !=-1 ) { +return ADCtoPower ((voltage+ConvRevise (voltage))); + }else { +return voltage; + } +} + +int collie_read_temp (void ) +{ +int voltage; + +/* temp must be > 973, main battery must be < 465 */ +/* FIXME sharpsl_pm.c has both conditions negated? */ + +ucb1x00_io_write (ucb,COLLIE_TC35143_GPIO_TMP_ON ,0 ); + voltage =ucb1x00_adc_read (ucb,UCB_ADC_INP_AD0 ,UCB_SYNC ); +ucb1x00_io_write (ucb,0 ,COLLIE_TC35143_GPIO_TMP_ON ); + +/* >1010 = battery removed. +460 = 22C ? +higer = lower temp ? +*/ + +printk ("Battery temp = %d\n" , voltage); +return voltage; +} + +static int collie_read_acin (void ) +{ +return 0x1 ; +} + +static unsigned long read_devdata (int which) +{ +switch (which) { +case SHARPSL_BATT_VOLT : +return collie_read_main_battery (); +case SHARPSL_BATT_TEMP : +return collie_read_temp (); +case SHARPSL_ACIN_VOLT : +return collie_read_acin (); +case SHARPSL_STATUS_ACIN : +case SHARPSL_STATUS_LOCK : +case SHARPSL_STATUS_CHRGFULL : +case SHARPSL_STATUS_FATAL : +default : +return ~0 ; + } +#if 0 +It should be okay. Nobody really needs those. + .gpio_batlock = COLLIE_GPIO_BAT_COVER, + .gpio_acin = COLLIE_GPIO_AC_IN, + .gpio_batfull = COLLIE_GPIO_CHRG_FULL, + .gpio_fatal = COLLIE_GPIO_FATAL_BAT, +#endif +} + +struct battery_thresh spitz_battery_levels_noac[] = { +#ifdef FOO_FRONTLIGHT + { 368, 100}, + { 358, 25}, + { 356, 5}, + { 0, 0}, +#else + { 378, 100}, + { 365, 25}, + { 363, 5}, + { 0, 0}, +#endif +}; + +struct battery_thresh spitz_battery_levels_acin[] = { +#ifdef FOO_FRONTLIGHT + { 368, 100}, + { 358, 25}, + { 356, 5}, + { 0, 0}, +#else + { 378, 100}, + { 365, 25}, + { 363, 5}, + { 0, 0}, +#endif +}; + +struct sharpsl_charger_machinfo collie_pm_machinfo = { + .init = collie_charger_init, + .read_devdata = read_devdata, + .discharge = collie_discharge, + .discharge1 = collie_discharge1, + .charge = collie_charge, + .measure_temp = collie_measure_temp, + .presuspend = collie_presuspend, + .postsuspend = collie_postsuspend, + .charger_wakeup = collie_charger_wakeup, + .should_wakeup = collie_should_wakeup, + .bat_levels = 3, + .bat_levels_noac = spitz_battery_levels_noac, + .bat_levels_acin = spitz_battery_levels_acin, + .status_high_acin = 368, + .status_low_acin = 358, + .status_high_noac = 368, + .status_low_noac = 358, +};
arch/arm/mach-sa1100/collie_pm.c line 301
Quoted 10 lines
arch/arm/mach-sa1100/collie_pm.c new file +10
-0+ +extern struct sharpsl_pm_status sharpsl_pm; + +static int __init collie_pm_add (struct ucb1x00_dev *pdev) +{ + sharpsl_pm.dev =NULL ; + sharpsl_pm.machinfo = &collie_pm_machinfo; + ucb = pdev->ucb; +return sharpsl_pm_init (); +}
I don't understand how this is supposed to work at all. For a start, sharpsl_pm.c says "static int __devinit sharpsl_pm_init(void)" so that function isn't available. I've just noticed your further patches although I still don't like this.
The correct approach is to register a platform device called "sharpsl-pm" in collie_pm_add() which the driver will then see and attach to. I'd also not register the platform device if ucb is NULL for whatever reason.
By setting sharpsl_pm.dev = NULL you're also going to miss out on suspend/resume calls and risk breaking things like dev_dbg(sharpsl_pm.dev, xxx).
Richard
Quoted 23 lines
arch/arm/mach-sa1100/collie_pm.c new file +22
-0+static int collie_pm_remove (struct ucb1x00_dev *pdev) +{ +return sharpsl_pm_done (); +} + +static struct ucb1x00_driver collie_pm_driver = { + .add = collie_pm_add, + .remove = collie_pm_remove, +}; + +static int __init collie_pm_init (void ) +{ +return ucb1x00_register_driver (&collie_pm_driver); +} + +static void __exit collie_pm_exit(void) +{ +ucb1x00_unregister_driver (&collie_pm_driver); +} + +late_initcall (collie_pm_init); +module_exit (collie_pm_exit);
Hi!
Quoted 9 lines
Quoted 5 lines
This is collie battery sensing code. It differs from sharpsl code a bit -- because it is dependend on ucb1x00, not on platform bus.
I guess I should reorganize #include's and remove #if 0-ed code. Anything else
Basically looks good. Could probably use a s/printk/dev_dbg(sharpsl_pm.dev, /. I've made a few other comments below.
I'll just remove most printks before next merge attempt, I guess.
Quoted 2 lines
Just for my interest, can you summarise the status of PM and charging on collie with this code?
Well, with heavy ifdefs into sharpsl_pm, it can correctly sense AC/battery. Voltmeters seem to return *some* values. Temperature is probably okay, battery level is *extremely* noisy, and outside range where sharp code expects it, but seems to correlate with actual battery levels.
Now... something does charge my battery, but it is definitely not my code. I don't dare enabling charging yet.
(More detailed reply will come later today, when I'm close to collie).
Quoted 8 lines
arch/arm/mach-sa1100/collie_pm.c line 32
Quoted 6 lines
arch/arm/mach-sa1100/collie_pm.c new file +6
-0+#include "../drivers/mfd/ucb1x00.h" +#include <asm/mach/sharpsl_param.h> + +#ifdef CONFIG_MCP_UCB1200_TS +#error Battery interferes with touchscreen +#endif Is this a case of bad locking or something more serious?
Original sharp code does some magic between TS and battery reading. It seems AD0 is used by both, or something similary ugly. I'll have to decipher sharp code and figure out how to do it properly.
Quoted 13 lines
arch/arm/mach-sa1100/collie_pm.c line 301
Quoted 7 lines
arch/arm/mach-sa1100/collie_pm.c new file +7
-0+static int __init collie_pm_add (struct ucb1x00_dev *pdev) +{ + sharpsl_pm.dev =NULL ; + sharpsl_pm.machinfo = &collie_pm_machinfo; + ucb = pdev->ucb; +return sharpsl_pm_init (); +}I don't understand how this is supposed to work at all. For a start,
sharpsl_pm.csays "static int__devinitsharpsl_pm_init(void)" so that function isn't available. I've just noticed your further patches although I still don't like this.
Quoted 4 lines
The correct approach is to register a platform device called "sharpsl-pm" in
collie_pm_add()which the driver will then see and attach to. I'd also not register the platform device if ucb is NULL for whatever reason.
I thought about it, and considered it quite ugly. Result would be all data on the platform bus with half-empty device on ucb1x00 "bus". It would bring me some problems with registering order: if platform device is registered too soon, ucb will be NULL and it will crash and burn. OTOH I already have static *ucb, so it is doable, and I can do it if you prefer it that way...
Signature · 1 line
Thanks, Sharp!
Quoted 8 lines · Pavel Machek
Quoted 2 lines
Just for my interest, can you summarise the status of PM and charging on collie with this code?
Well, with heavy ifdefs into
sharpsl_pm, it can correctly sense AC/battery. Voltmeters seem to return *some* values. Temperature is probably okay, battery level is *extremely* noisy, and outside range where sharp code expects it, but seems to correlate with actual battery levels.
The sharp code often had delays in it to allow voltages to stablise etc. I still see noise issues on one of the devices. A particularly puzzling spitz noise issue is when I make the battery reading whilst suspended without loading the power supply line with an LED :-/. (the sharp code didn't do this but I can find now other way to make it work).
Quoted 9 lines
Quoted 8 lines
arch/arm/mach-sa1100/collie_pm.c line 32
Quoted 6 lines
arch/arm/mach-sa1100/collie_pm.c new file +6
-0+#include "../drivers/mfd/ucb1x00.h" +#include <asm/mach/sharpsl_param.h> + +#ifdef CONFIG_MCP_UCB1200_TS +#error Battery interferes with touchscreen +#endif Is this a case of bad locking or something more serious?
Quoted 3 lines
Original sharp code does some magic between TS and battery reading. It seems AD0 is used by both, or something similary ugly. I'll have to decipher sharp code and figure out how to do it properly.
ok.
Quoted 18 lines
Quoted 13 lines
arch/arm/mach-sa1100/collie_pm.c line 301
Quoted 7 lines
arch/arm/mach-sa1100/collie_pm.c new file +7
-0+static int __init collie_pm_add (struct ucb1x00_dev *pdev) +{ + sharpsl_pm.dev =NULL ; + sharpsl_pm.machinfo = &collie_pm_machinfo; + ucb = pdev->ucb; +return sharpsl_pm_init (); +}I don't understand how this is supposed to work at all. For a start,
sharpsl_pm.csays "static int__devinitsharpsl_pm_init(void)" so that function isn't available. I've just noticed your further patches although I still don't like this.Quoted 4 lines
The correct approach is to register a platform device called "sharpsl-pm" in
collie_pm_add()which the driver will then see and attach to. I'd also not register the platform device if ucb is NULL for whatever reason.
Quoted 6 lines
I thought about it, and considered it quite ugly. Result would be all data on the platform bus with half-empty device on ucb1x00 "bus". It would bring me some problems with registering order: if platform device is registered too soon, ucb will be NULL and it will crash and burn. OTOH I already have static *ucb, so it is doable, and I can do it if you prefer it that way...
If you register the sharpsl-pm device in the collie_pm_add() function, ucb should always have registered by that point? As you say, you already have the static *ucb and I'm hoping using the platform device will mean less invasive changes in sharpsl_pm itself in the future?
For the record, this patch from Dirk Opfer also exists. He's working on using sharpsl-pm on tosa.
http://www.rpsys.net/openzaurus/patches/archive/sharpsl_pm-do-r2.patch
Richard
Hi!
Quoted 11 lines
Quoted 6 lines
I thought about it, and considered it quite ugly. Result would be all data on the platform bus with half-empty device on ucb1x00 "bus". It would bring me some problems with registering order: if platform device is registered too soon, ucb will be NULL and it will crash and burn. OTOH I already have static *ucb, so it is doable, and I can do it if you prefer it that way...
If you register the sharpsl-pm device in the
collie_pm_add()function, ucb should always have registered by that point? As you say, you already have the static *ucb and I'm hoping using the platform device will mean less invasive changes insharpsl_pmitself in the future?
Well, difference is not going to be
Quoted 4 lines
For the record, this patch from Dirk Opfer also exists. He's working on using sharpsl-pm on tosa.
http://www.rpsys.net/openzaurus/patches/archive/sharpsl_pm-do-r2.patch
Yep, looks nice, and will be useful for collie, too.
Pavel
Signature · 1 line
68: byte [] adUSER = GetAtomData( GetAtomPos( AtomUSER ), true );
Hi!
Quoted 9 lines
Quoted 5 lines
This is collie battery sensing code. It differs from sharpsl code a bit -- because it is dependend on ucb1x00, not on platform bus.
I guess I should reorganize #include's and remove #if 0-ed code. Anything else
Basically looks good. Could probably use a s/printk/dev_dbg(sharpsl_pm.dev, /. I've made a few other comments below.
Ok, comments below.
Quoted 5 lines
arch/arm/mach-sa1100/collie_pm.c line 26
Quoted 2 lines
arch/arm/mach-sa1100/collie_pm.c new file +2
-0+#include <asm/arch/collie.h> +#include "../mach-pxa/sharpsl.h" Do you need anything in the above header? If so, it should probably be in
asm/hardware/sharpsl_pm.h
Thanks, fixed.
Quoted 11 lines
arch/arm/mach-sa1100/collie_pm.c line 114
Quoted 9 lines
arch/arm/mach-sa1100/collie_pm.c new file +9
-0+#ifdef I_AM_SURE +#define CF_BUF_CTRL_BASE 0xF0800000 +#define SCOOP_REG (adr) (*(volatile unsigned short*)(CF_BUF_CTRL_BASE+(adr))) +#define SCOOP_REG_GPWR SCOOP_REG(SCOOP_GPWR) + +if (on) { +SCOOP_REG_GPWR |=COLLIE_SCP_CHARGE_ON ; + }else { +SCOOP_REG_GPWR &= ~COLLIE_SCP_CHARGE_ON ;Ick. Use
arch/arm/common/scoop.cto do this. Something like:
Thanks, fixed.
Quoted 15 lines
arch/arm/mach-sa1100/collie_pm.c line 301
Quoted 9 lines
arch/arm/mach-sa1100/collie_pm.c new file +9
-0+extern struct sharpsl_pm_status sharpsl_pm; + +static int __init collie_pm_add (struct ucb1x00_dev *pdev) +{ + sharpsl_pm.dev =NULL ; + sharpsl_pm.machinfo = &collie_pm_machinfo; + ucb = pdev->ucb; +return sharpsl_pm_init (); +}I don't understand how this is supposed to work at all. For a start,
sharpsl_pm.csays "static int__devinitsharpsl_pm_init(void)" so that function isn't available. I've just noticed your further patches although I still don't like this.
Quoted 8 lines
The correct approach is to register a platform device called "sharpsl-pm" in
collie_pm_add()which the driver will then see and attach to. I'd also not register the platform device if ucb is NULL for whatever reason.By setting sharpsl_pm.dev = NULL you're also going to miss out on suspend/resume calls and risk breaking things like
dev_dbg(sharpsl_pm.dev, xxx).
Ok, I'll try to switch it to two-device config.
Pavel
Signature · 1 line
28:class DeDRMS