Linux v2.6.16-rc6
Are these UDMA transfer rates normal?
libata version 1.20 loaded.sata_nv 0000:00:07.0: version 0.8
ACPI: PCI Interrupt Link [APSI] enabled at IRQ 22
ACPI: PCI Interrupt 0000:00: 07.0[A] -> Link [APSI] -> GSI 22 (level, low) -> IRQ 20
PCI: Setting latency timer of device 0000:00:07.0 to 64
ata1: SATA max UDMA/133 cmd 0x9F0 ctl 0xBF2 bmdma 0xD800 irq 20
ata2: SATA max UDMA/133 cmd 0x970 ctl 0xB72 bmdma 0xD808 irq 20
ata1: SATA link down (SStatus 0)
scsi1 : sata_nv
ata2: SATA link down (SStatus 0)
scsi2 : sata_nv
ACPI: PCI Interrupt Link [APSJ] enabled at IRQ 21
ACPI: PCI Interrupt 0000:00:08.0[A] -> Link [APSJ] -> GSI 21 (level, low) -=
Quoted 1 line
IRQ 21
PCI: Setting latency timer of device 0000:00:08.0 to 64
ata3: SATA max UDMA/133 cmd 0x9E0 ctl 0xBE2 bmdma 0xC400 irq 21
ata4: SATA max UDMA/133 cmd 0x960 ctl 0xB62 bmdma 0xC408 irq 21
eth0: link up.
ata3: SATA link up 1.5 Gbps (SStatus 113)
ieee1394: Host added: ID:BUS[0-00:1023] GUID[00023c0091065c55]
ata3: dev 0 cfg 49:2f00 82:306b 83:7e01 84:4003 85:3068 86:3c01 87:4003 88:203f
ata3: dev 0 ATA-6, max UDMA/100, 390721968 sectors: LBA48nv_sata: Primary device addednv_sata: Primary device removednv_sata: Secondary device addednv_sata: Secondary device removed
ata3: dev 0 configured for UDMA/100
scsi3 : sata_nv
ieee1394: Host added: ID:BUS[1-00:1023] GUID[0011d800004f6359]
ata4: SATA link up 1.5 Gbps (SStatus 113)
ata4: dev 0 cfg 49:2f00 82:346b 83:7f61 84:4003 85:3468 86:3c41 87:4003 88:407f
ata4: dev 0 ATA-6, max UDMA/133, 390721968 sectors: LBA48nv_sata: Primary device addednv_sata: Primary device removednv_sata: Secondary device addednv_sata: Secondary device removed
ata4: dev 0 configured for UDMA/133
scsi4 : sata_nv
Vendor: ATA Model: WDC WD2000JD-60K Rev: 08.0
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 390721968 512-byte hdwr sectors (200050 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
SCSI device sdb: 390721968 512-byte hdwr sectors (200050 MB)
sdb: Write Protect is off
sdb: Mode Sense: 00 3a 00 00
SCSI device sdb: drive cache: write back
sdb:<4>nv_sata: Primary device addednv_sata: Primary device removednv_sata: Secondary device addednv_sata: Secondary device removed
sdb1 sdb2 sdb3 sdb4
sd 3:0:0:0: Attached scsi disk sdb
Vendor: ATA Model: WDC WD2000JD-00H Rev: 08.0
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdc: 390721968 512-byte hdwr sectors (200050 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
SCSI device sdc: 390721968 512-byte hdwr sectors (200050 MB)
sdc: Write Protect is off
sdc: Mode Sense: 00 3a 00 00
SCSI device sdc: drive cache: write back
sdc:<4>nv_sata: Primary device addednv_sata: Primary device removednv_sata: Secondary device addednv_sata: Secondary device removed
sdc1 sdc2 sdc3 sdc4
sd 4:0:0:0: Attached scsi disk sdc
Cheers!
Paul B.
Quoted 3 lines · Paul Blazejowski
Are these UDMA transfer rates normal?
Please be less cryptic.
What behaviour are you expecting to see?
How does the current behaviour appear to be incorrect?
What was the behaviour in previous kernels? (Which version?)
What actual probelms are observable? Oops? Hang? Corruption? Nothing?
Quoted 2 lines
ata1: SATA link down (SStatus 0)
Just a little cosmetic-o: is it really "SStatus" or should it be "Status"?
Jan Engelhardt
Quoted 4 lines · On Mon, 13 Mar 2006 21:14:48 +0100 (MET) Jan Engelhardt wrote:
Quoted 2 lines
ata1: SATA link down (SStatus 0)
Just a little cosmetic-o: is it really "SStatus" or should it be "Status"?
it's not a typo.
---
~Randy
You can't do anything without having to do something else first. -- Belefant's Law