Skip to contentSkip to conversation

PATCH: Simplex and other mode filtering logic

PATCH Applied Alan Cox 2 participants 2 messages Mar 27, 2006 – Mar 30, 2006

Subsystems (3)
lore
Share & tools
lore

Alan Cox

author
#0 lore raw

Add a field to the host_set called 'flags' (was host_set_flags changed to suit Jeff)
Add a simplex_claimed field so we can remember who owns the DMA channel Add a ->mode_filter() hook to allow drivers to filter modes Add docs for mode_filter and set_mode
Filter according to simplex state
Filter cable in core

This provides the needed framework to support all the mode rules found in the PATA world. The simplex filter deals with 'to spec' simplex DMA systems found in older chips. The cable filter avoids duplicating the same rules in each chip driver with PATA. Finally the mode filter is neccessary because drive/chip combinations have errata that forbid certain modes with some drives or types of ATA object.

Drive speed setup remains per channel for now and the filters now use the framework Tejun put into place which cleans them up a lot from the older libata-pata patches.

include/linux/libata.h +4 -0
index 9fcc061..26e0351 100644
@@ -290,6 +295,9 @@ struct ata_host_set {
 	unsigned int		n_ports;
 	void			*private_data;
 	const struct ata_port_operations *ops;
+	unsigned long		flags;
+	int			simplex_claimed;	/* Keep seperate in case we
+							   ever need to do this locked */
 	struct ata_port *	ports[0];
 };
 
@@ -419,6 +427,7 @@ struct ata_port_operations {
 
 	void (*set_piomode) (struct ata_port *, struct ata_device *);
 	void (*set_dmamode) (struct ata_port *, struct ata_device *);
+	unsigned long (*mode_filter) (const struct ata_port *, struct ata_device *, unsigned long);
 
 	void (*tf_load) (struct ata_port *ap, const struct ata_taskfile *tf);
 	void (*tf_read) (struct ata_port *ap, struct ata_taskfile *tf);
drivers/scsi/libata-core.c +29 -2
index 1cb9813..18d5239 100644
@@ -1814,7 +1824,7 @@ static void ata_host_set_dma(struct ata_
  */
 static void ata_set_mode(struct ata_port *ap)
 {
-	int i, rc;
+	int i, rc, used_dma = 0;
 
 	/* step 1: calculate xfer_mask */
 	for (i = 0; i < ATA_MAX_DEVICES; i++) {
@@ -1832,6 +1842,9 @@ static void ata_set_mode(struct ata_port
 		dma_mask = ata_pack_xfermask(0, dev->mwdma_mask, dev->udma_mask);
 		dev->pio_mode = ata_xfer_mask2mode(pio_mask);
 		dev->dma_mode = ata_xfer_mask2mode(dma_mask);
+
+		if (dev->dma_mode)
+			used_dma = 1;
 	}
 
 	/* step 2: always set host PIO timings */
@@ -1853,6 +1866,17 @@ static void ata_set_mode(struct ata_port
 			goto err_out;
 	}
 
+	/*
+	 *	Record simplex status. If we selected DMA then the other
+	 *	host channels are not permitted to do so.
+	 */
+
+	if (used_dma && (ap->host_set->flags & ATA_HOST_SIMPLEX))
+		ap->host_set->simplex_claimed = 1;
+
+	/*
+	 *	Chip specific finalisation
+	 */
 	if (ap->ops->post_set_mode)
 		ap->ops->post_set_mode(ap);
 
@@ -2642,13 +2666,14 @@ static int ata_dma_blacklisted(const str
  */
 static void ata_dev_xfermask(struct ata_port *ap, struct ata_device *dev)
 {
+	struct ata_host_set *hs = ap->host_set;
 	unsigned long xfer_mask;
 	int i;
 
 	xfer_mask = ata_pack_xfermask(ap->pio_mask, ap->mwdma_mask,
 				      ap->udma_mask);
 
-	/* use port-wide xfermask for now */
+	/* FIXME: Use port-wide xfermask for now */
 	for (i = 0; i < ATA_MAX_DEVICES; i++) {
 		struct ata_device *d = &ap->device[i];
 		if (!ata_dev_present(d))
@@ -2658,12 +2683,23 @@ static void ata_dev_xfermask(struct ata_
 		xfer_mask &= ata_id_xfermask(d->id);
 		if (ata_dma_blacklisted(d))
 			xfer_mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
+		/* Apply cable rule here. Don't apply it early because when
+		   we handle hot plug the cable type can itself change */
+		if (ap->cbl == ATA_CBL_PATA40)
+			xfer_mask &= ~(0xF8 << ATA_SHIFT_UDMA);
 	}
 
 	if (ata_dma_blacklisted(dev))
 		printk(KERN_WARNING "ata%u: dev %u is on DMA blacklist, "
 		       "disabling DMA\n", ap->id, dev->devno);
 
+	if (hs->flags & ATA_HOST_SIMPLEX) {
+		if (hs->simplex_claimed)
+			xfer_mask &= ~(ATA_MASK_MWDMA | ATA_MASK_UDMA);
+	}
+	if (ap->ops->mode_filter)
+		xfer_mask = ap->ops->mode_filter(ap, dev, xfer_mask);
+
 	ata_unpack_xfermask(xfer_mask, &dev->pio_mask, &dev->mwdma_mask,
 			    &dev->udma_mask);
 }
@@ -4527,6 +4539,7 @@ int ata_device_add(const struct ata_prob
 	host_set->mmio_base = ent->mmio_base;
 	host_set->private_data = ent->private_data;
 	host_set->ops = ent->port_ops;
+	host_set->flags = ent->host_set_flags;
 
 	/* register each port bound to this device */
 	for (i = 0; i < ent->n_ports; i++) {
Documentation/DocBook/libata.tmpl +43 -4

63 lines not on this page · raw message

Applied
#1 lore raw
Quoted 15 lines · Alan Cox

Add a field to the host_set called 'flags' (was host_set_flags changed to suit Jeff)
Add a simplex_claimed field so we can remember who owns the DMA channel Add a ->mode_filter() hook to allow drivers to filter modes Add docs for mode_filter and set_mode
Filter according to simplex state
Filter cable in core

This provides the needed framework to support all the mode rules found in the PATA world. The simplex filter deals with 'to spec' simplex DMA systems found in older chips. The cable filter avoids duplicating the same rules in each chip driver with PATA. Finally the mode filter is neccessary because drive/chip combinations have errata that forbid certain modes with some drives or types of ATA object.

Quoted 5 lines

Drive speed setup remains per channel for now and the filters now use the framework Tejun put into place which cleans them up a lot from the older libata-pata patches.

applied