Skip to contentSkip to conversation

Enabling both SMC ports

U-Boot-Users Kamesh K S 2 participants 4 messages Apr 12, 2006

lore
Share & tools
lore

Kamesh K S

author
#0 lore raw

Hi All, Our product ( MPC860 arch with Mvista Kernel) has one serial port connected to the console & is interfaced thru' SMC1.The second serial port needs to be connected to the printer thru' SMC2. The u-boot does not allow enabling SMC1 & SMC2 both togather.
How do I go about achieving this ?

Rgds

Kamesh
Member, Software Group
Signal Networks PVT. LTD

#1 lore raw
Quoted 4 lines · In message <[email protected]> you wrote:

Hi All, Our product ( MPC860 arch with Mvista Kernel) has one serial port connected to the console & is interfaced thru' SMC1.The second serial port needs to be connected to the printer thru' SMC2. The u-boot does not allow enabling SMC1 & SMC2 both togather.

You porbably don't want to control your printer by U-Boot anyway, or do you?

And Linux has no such limitations.

How do I go about achieving this ?

If you really want to use both SMC ports in U-Boot you have to extend the existing driver. But I don't see why you would want to do this.

Best regards,

Wolfgang Denk

Signature · 4 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
If you can't beat it or corrupt it, you pretend it was your  idea  in
the first place.                 - Terry Pratchett, _Guards! Guards!_
author
#2 lore raw

Hi WD,
First of all Thanks for your prompt reply.
I needed further info on this issue.
I have already tried enabling the SMC2 in the kernel. This is what I tried:

$ make menuconfig 

1) Selected MPC8xx CPM Options and Enabled the Foll.
i) Use SMC2 for UART
ii) Use SMC2 for Console

Then Compiled the kernel & ported it to the board (MPC860) Connected the serial printer to SMC2.
Tried printing using 'cat' command

$ cat <file-name> > /dev/ttyS1  (since /dev/ttyS0 is for console) 
Command gets executed but printer does not print anything.

Have I missed anything or not tried enough ?
Is there any other workaround ?

Your suggestions would be valuable.

Rgds
Kamesh

Quoted 26 lines · Wolfgang Denk
Quoted 4 lines · In message <[email protected]> you wrote:

Hi All, Our product ( MPC860 arch with Mvista Kernel) has one serial port connected to the console & is interfaced thru' SMC1.The second serial port needs to be connected to the printer thru' SMC2. The u-boot does not allow enabling SMC1 & SMC2 both togather.

You porbably don't want to control your printer by U-Boot anyway, or do you?

And Linux has no such limitations.

How do I go about achieving this ?

If you really want to use both SMC ports in U-Boot you have to extend the existing driver. But I don't see why you would want to do this.

Best regards,

Wolfgang Denk

Signature · 4 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
If you can't beat it or corrupt it, you pretend it was your  idea  in
the first place.                 - Terry Pratchett, _Guards! Guards!_
#3 lore raw
Quoted 2 lines · In message <[email protected]> you wrote:

I have already tried enabling the SMC2 in the kernel.

This is off topic here.

[And without further information about your hardware, your kernel version and how it was ported to your hardware you should not expect much help from any other mailing list, either.]

Best regards,

Wolfgang Denk

Signature · 4 lines
Software Engineering:  Embedded and Realtime Systems,  Embedded Linux
Phone: (+49)-8142-66989-10 Fax: (+49)-8142-66989-80 Email: wd at denx.de
You can love it, change it, or leave it.    There is NO other option.
But do not complain - it is your own choice...                  -- wd