ipath patches for 2.6.17
PATCH 1/1 ipath patches for 2.6.17
Hi, Roland -
Here are some patches for 2.6.17. They all fix kernel or userspace crasher bugs. I may have a few more for you in a while, too.
Regards,
<b
PATCH 1/1 ipath - fix reporting of driver version to userspace
Fix the interface version that gets exported to userspace.
drivers/infiniband/hw/ipath/ipath_file_ops.c +1 -1
@@ -139,7 +139,7 @@ static int ipath_get_base_info(struct ip kinfo->spi_piosize = dd->ipath_ibmaxlen; kinfo->spi_mtu = dd->ipath_ibmaxlen;/* maxlen, not ibmtu */ kinfo->spi_port = pd->port_port; - kinfo->spi_sw_version =IPATH_USER_SWVERSION ; + kinfo->spi_sw_version =IPATH_KERN_SWVERSION ; kinfo->spi_hw_version = dd->ipath_revision;if (copy_to_user (ubase, kinfo,sizeof (*kinfo)))
PATCH 1/1 ipath - fix spinlock recursion bug
In reply to Bryan O'SullivanThe local loopback path for RC can lock the rkey table lock without blocking interrupts. The receive interrupt path can then call ipath_rkey_ok() and deadlock. Remove the redundant lock.
drivers/infiniband/hw/ipath/ipath_keys.c +0 -6
@@ -136,9 +136,7 @@ int ipath_lkey_ok(struct ipath_lkey_tabl ret =1 ; goto bail; } -spin_lock (&rkt->lock); mr = rkt->table[(sge->lkey >> (32 - ib_ipath_lkey_table_size))]; -spin_unlock (&rkt->lock);if (unlikely (mr ==NULL || mr->lkey != sge->lkey)) { ret =0 ; goto bail;
@@ -184,8 +182,6 @@ bail:* @acc: access flags * * Return 1 if successful, otherwise 0. -* -* The QP r_rq.lock should be held. */ int ipath_rkey_ok (struct ipath_ibdev *dev,struct ipath_sge_state *ss,u32 len,u64 vaddr,u32 rkey,int acc)
@@ -196,9 +192,7 @@ int ipath_rkey_ok(struct ipath_ibdev *desize_t off;int ret; -spin_lock (&rkt->lock); mr = rkt->table[(rkey >> (32 - ib_ipath_lkey_table_size))]; -spin_unlock (&rkt->lock);if (unlikely (mr ==NULL || mr->lkey != rkey)) { ret =0 ; goto bail;
Re: [PATCH 1 of 10] ipath - fix spinlock recursion bug
Thanks, I've put 1 through 10 into my git tree and asked Linus to pull.
BTW, I just tried SRP with 2.6.17-rc4 + my for-2.6.18 tree + all of these patches, and immediately after connecting to a storage target I get the following:
Kernel BUG at drivers/infiniband/hw/ipath/ipath_layer.c:761
invalid opcode: 0000 [1] SMP
CPU 0
Modules linked in: ib_srp ib_cm ib_sa ib_mad ib_ipath ib_core ipv6 thermal fan button processor ac battery nfs lockd nfs_acl sunrpc dm_mod ide_generic ide_disk ide_cd cdrom e1000 amd74xx shpchp generic pci_hotplug ipath_core parport_pc parport psmouse ohci_hcd ide_core ehci_hcd serio_raw pcspkr
Pid: 3623, comm: udevd Not tainted 2.6.17-rc4 #4
RIP: 0010:[<ffffffff880737d5>] <ffffffff880737d5>{:ipath_core:ipath_verbs_send+364}
RSP: 0000:ffffffff804e1e28 EFLAGS: 00010246
RAX: ffff8101a02b4148 RBX: 0000000000000000 RCX: 0000000000000000
RDX: ffff8101a02b4148 RSI: ffff8101a02b40b0 RDI: ffffc200001c8020
RBP: 0000000000000000 R08: ffff8101a02b4148 R09: 0000000000000002
R10: ffff8101a02b41b0 R11: 000000021e056480 R12: 0000000000000000
R13: ffffc200001c8020 R14: 0000000000000040 R15: 0000000000000010
FS: 00002b8024bbcae0(0000) GS:ffffffff80537000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b
CR2: 00002b8024513350 CR3: 00000001a0075000 CR4: 00000000000006e0
Process udevd (pid: 3623, threadinfo ffff81021cc8e000, task ffff8101a02b8770)
Stack: 0000000000000092 ffff8101a02b4148 ffff8101a02b4098 0000000016000003
ffff8101a02b4000 000000000000000a 0000000000000000 0000000000000014
ffff8101a02b40a0 ffffffff881e29ec
Call Trace: <IRQ> <ffffffff881e29ec>{:ib_ipath:ipath_do_rc_send+384}
<ffffffff8820aea9>{:ib_srp:srp_completion+631} <ffffffff8022e523>{tasklet_hi_action+96}
<ffffffff8022e5c3>{__do_softirq+86} <ffffffff8020a97a>{call_softirq+30}
<ffffffff8020c39a>{do_softirq+44} <ffffffff8020c3df>{do_IRQ+65}
<ffffffff80209cd8>{ret_from_intr+0} <EOI> <ffffffff80258d12>{__handle_mm_fault+1278}
<ffffffff80219024>{do_page_fault+796} <ffffffff80219007>{do_page_fault+767}
<ffffffff80391b6e>{datagram_poll+0} <ffffffff8020a471>{error_exit+0}
Code: 0f 0b 68 22 e9 07 88 c2 f9 02 eb 07 44 39 f5 41 0f 47 ee 48RIP <ffffffff880737d5>{:ipath_core:ipath_verbs_send+364} RSP <ffffffff804e1e28>
Re: [PATCH 1 of 10] ipath - fix spinlock recursion bug
Quoted 1 line · Roland Dreier
Thanks, I've put 1 through 10 into my git tree and asked Linus to pull.
Thanks.
Quoted 3 lines
BTW, I just tried SRP with 2.6.17-rc4 + my for-2.6.18 tree + all of these patches, and immediately after connecting to a storage target I get the following:
Yes, I have another large pile of fixes to sort out. Unfortunately, all of them depend on some "code motion" driver changes that, in an ideal world, should be deferred until 2.6.18. Regenerating and testing them against 2.6.17, without the code motion, is a big pain in the big painful body region.
How do you feel about taking one code motion patch for 2.6.17? :-)
<b
Re: [PATCH 1 of 10] ipath - fix spinlock recursion bug
Bryan> How do you feel about taking one code motion patch for Bryan> 2.6.17? :-)
It's probably OK as long as it's pure code motion. In other words separate the actual fixes from moving code around. What I want to avoid is the giant combo patch that does several different things, because if someone later bisects a regression back to that patch, we're kind of screwed...
- R.
Re: [PATCH 1 of 10] ipath - fix spinlock recursion bug
Quoted 1 line · Roland Dreier
It's probably OK as long as it's pure code motion.
I'll recheck and make sure that it is before I send you anything. Thanks.
Quoted 4 lines
What I want to
avoid is the giant combo patch that does several different things, because if someone later bisects a regression back to that patch, we're kind of screwed...
Yeah, I've been doing some educating lately about that :-)
<b
PATCH 1/1 ipath - enable PE800 receive interrupts on user ports
In reply to Bryan O'SullivanFixed so it works on the PE-800. It had not previously been updated to match PE-800 receive interrupt differences from HT-400.
drivers/infiniband/hw/ipath/ipath_file_ops.c +4 -0
@@ -1224,6 +1224,10 @@ static unsigned int ipath_poll(struct fiif (tail == head) {set_bit (IPATH_PORT_WAITING_RCV , &pd->port_flag); +if (dd->ipath_rhdrhead_intr_off)/* arm rcv interrupt */ + (void )ipath_write_ureg (dd, ur_rcvhdrhead, + dd->ipath_rhdrhead_intr_off + | head, pd->port_port);poll_wait (fp, &pd->port_wait, pt);if (test_bit (IPATH_PORT_WAITING_RCV , &pd->port_flag)) {
PATCH 1/1 ipath - fix null deref during rdma ops
In reply to Bryan O'SullivanThe problem was that node A's sending thread, which handles sending RDMA read response data, would write the trigger word, the last packet would be sent, node B would send a new RDMA read request, node A's interrupt handler would initialize s_rdma_sge, then node A's sending thread would update s_rdma_sge. This didn't happen very often naturally but was more frequent with 1 byte RDMA reads. Rather than adding more locking or increasing the QP structure size and copying sge data, I modified the copy routine to update the pointers before writing the trigger word to avoid the update race.
drivers/infiniband/hw/ipath/ipath_layer.c +8 -6
@@ -872,12 +872,13 @@ static void copy_io(u32 __iomem *piobuf,update_sge (ss, len); length -= len; } +/* Update address before sending packet. */ +update_sge (ss, length);/* must flush early everything before trigger word */ ipath_flush_wc ();__raw_writel (last, piobuf);/* be sure trigger word is written */ ipath_flush_wc (); -update_sge (ss, length); }/**
@@ -943,17 +944,18 @@ int ipath_verbs_send(struct ipath_devdatif (likely (ss->num_sge ==1 && len <= ss->sge.length && !((unsigned long )ss->sge.vaddr & (sizeof (u32) -1 )))) {u32 w; - +u32 *addr = (u32 *) ss->sge.vaddr; + +/* Update address before sending packet. */ +update_sge (ss, len);/* Need to round up for the last dword in the packet. */ w = (len +3 ) >>2 ; -__iowrite32_copy (piobuf, ss->sge.vaddr, w -1 ); +__iowrite32_copy (piobuf, addr, w -1 );/* must flush early everything before trigger word */ ipath_flush_wc (); -__raw_writel (((u32 *) ss->sge.vaddr)[w -1 ], - piobuf + w -1 ); +__raw_writel (addr[w -1 ], piobuf + w -1 );/* be sure trigger word is written */ ipath_flush_wc (); -update_sge (ss, len); ret =0 ; goto bail; }
PATCH 1/1 ipath - enable GPIO interrupt on HT-460
In reply to Bryan O'SullivanThis is required for even semi-decent performance on OpenIB.
drivers/infiniband/hw/ipath/ipath_eeprom.c +4 -5
@@ -505,11 +505,10 @@ static u8 flash_csum(struct ipath_flash* ipath_get_guid - get the GUID from the i2c device * @dd: the infinipath device * -* When we add the multi-chip support, we will probably have to add -* the ability to use the number of guids field, and get the guid from -* the first chip's flash, to use for all of them. -*/ -void ipath_get_guid (struct ipath_devdata *dd) +* We have the capability to use the ipath_nguid field, and get +* the guid from the first chip's flash, to use for all of them. +*/ +void ipath_get_eeprom_info (struct ipath_devdata *dd) {void *buf;struct ipath_flash *ifp;
drivers/infiniband/hw/ipath/ipath_ht400.c +19 -2
@@ -607,7 +607,12 @@ static int ipath_ht_boardname(struct ipacase 4 :/* Ponderosa is one of the bringup boards */ n ="Ponderosa" ;break ; -case 5 :/* HT-460 original production board */ +case 5 : +/* +* HT-460 original production board; two production levels, with +* different serial number ranges. See ipath_ht_early_init() for +* case where we enable IPATH_GPIO_INTR for later serial # range. +*/ n ="InfiniPath_HT-460" ;break ;case 6 :
@@ -642,7 +647,7 @@ static int ipath_ht_boardname(struct ipaif (n)snprintf (name, namelen,"%s" , n); -if (dd->ipath_majrev !=3 || dd->ipath_minrev !=2 ) { +if (dd->ipath_majrev !=3 || (dd->ipath_minrev <2 || dd->ipath_minrev >3 )) {/* * This version of the driver only supports the HT-400 * Rev 3.2
@@ -1520,6 +1525,18 @@ static int ipath_ht_early_init(struct ip*/ ipath_write_kreg (dd, dd->ipath_kregs->kr_sendctrl,INFINIPATH_S_ABORT ); + +ipath_get_eeprom_info (dd); +if (dd->ipath_boardrev ==5 && dd->ipath_serial[0 ] =='1' && + dd->ipath_serial[1 ] =='2' && dd->ipath_serial[2 ] =='8' ) { +/* +* Later production HT-460 has same changes as HT-465, so +* can use GPIO interrupts. They have serial #'s starting +* with 128, rather than 112. +*/ + dd->ipath_flags |=IPATH_GPIO_INTR ; + dd->ipath_flags &= ~IPATH_POLL_RX_INTR ; + }return 0 ; }
drivers/infiniband/hw/ipath/ipath_init_chip.c +0 -1
@@ -879,7 +879,6 @@ int ipath_init_chip(struct ipath_devdata done:if (!ret) { -ipath_get_guid (dd); *dd->ipath_statusp |=IPATH_STATUS_CHIP_PRESENT ;if (!dd->ipath_f_intrsetup (dd)) {/* now we can enable all interrupts from the chip */
drivers/infiniband/hw/ipath/ipath_kernel.h +1 -1
@@ -650,7 +650,7 @@ void ipath_init_pe800_funcs(struct ipathvoid ipath_init_pe800_funcs (struct ipath_devdata *);/* init HT-400-specific func */ void ipath_init_ht400_funcs (struct ipath_devdata *); -void ipath_get_guid (struct ipath_devdata *); +void ipath_get_eeprom_info (struct ipath_devdata *);u64 ipath_snap_cntr (struct ipath_devdata *,ipath_creg );/*
drivers/infiniband/hw/ipath/ipath_pe800.c +2 -0
@@ -1180,6 +1180,8 @@ static int ipath_pe_early_init(struct ip*/ dd->ipath_rhdrhead_intr_off =1ULL <<32 ; +ipath_get_eeprom_info (dd); +return 0 ; }
PATCH 1/1 ipath - deref correct pointer when using kernel SMA
In reply to Bryan O'SullivanAt this point, the core QP structure hasn't been initialized, so what's in there isn't valid. Get the same information elsewhere.
drivers/infiniband/hw/ipath/ipath_qp.c +1 -1
@@ -734,7 +734,7 @@ struct ib_qp *ipath_create_qp(struct ib_ipath_reset_qp (qp);/* Tell the core driver that the kernel SMA is present. */ -if (qp->ibqp.qp_type ==IB_QPT_SMI ) +if (init_attr->qp_type ==IB_QPT_SMI )ipath_layer_set_verbs_flags (dev->dd,IPATH_VERBS_KERNEL_SMA );break ;
PATCH 1/1 ipath - register as IB device owner
In reply to Bryan O'SullivanThis fixes an oops.
drivers/infiniband/hw/ipath/ipath_verbs.c +1 -0
@@ -951,6 +951,7 @@ static void *ipath_register_ib_device(in idev->dd = dd;strlcpy (dev->name,"ipath%d" ,IB_DEVICE_NAME_MAX ); + dev->owner =THIS_MODULE ; dev->node_guid =ipath_layer_get_guid (dd); dev->uverbs_abi_ver =IPATH_UVERBS_ABI_VERSION ; dev->uverbs_cmd_mask =
PATCH 1/1 ipath - replace uses of LIST_POISON
In reply to Bryan O'SullivanPer Andrew's request.
drivers/infiniband/hw/ipath/ipath_qp.c +14 -16
@@ -375,10 +375,10 @@ static void ipath_error_qp(struct ipath_spin_lock (&dev->pending_lock);/* XXX What if its already removed by the timeout code? */ -if (qp->timerwait.next !=LIST_POISON1 ) -list_del (&qp->timerwait); -if (qp->piowait.next !=LIST_POISON1 ) -list_del (&qp->piowait); +if (!list_empty (&qp->timerwait)) +list_del_init (&qp->timerwait); +if (!list_empty (&qp->piowait)) +list_del_init (&qp->piowait);spin_unlock (&dev->pending_lock); wc.status =IB_WC_WR_FLUSH_ERR ;
@@ -712,10 +712,8 @@ struct ib_qp *ipath_create_qp(struct ib_ init_attr->qp_type ==IB_QPT_RC ? ipath_do_rc_send : ipath_do_uc_send, (unsigned long)qp); - qp->piowait.next =LIST_POISON1 ; - qp->piowait.prev =LIST_POISON2 ; - qp->timerwait.next =LIST_POISON1 ; - qp->timerwait.prev =LIST_POISON2 ; +INIT_LIST_HEAD (&qp->piowait); +INIT_LIST_HEAD (&qp->timerwait); qp->state =IB_QPS_RESET ; qp->s_wq = swq; qp->s_size = init_attr->cap.max_send_wr +1 ;
@@ -785,10 +783,10 @@ int ipath_destroy_qp(struct ib_qp *ibqp)/* Make sure the QP isn't on the timeout list. */ spin_lock_irqsave (&dev->pending_lock, flags); -if (qp->timerwait.next !=LIST_POISON1 ) -list_del (&qp->timerwait); -if (qp->piowait.next !=LIST_POISON1 ) -list_del (&qp->piowait); +if (!list_empty (&qp->timerwait)) +list_del_init (&qp->timerwait); +if (!list_empty (&qp->piowait)) +list_del_init (&qp->piowait);spin_unlock_irqrestore (&dev->pending_lock, flags);/*
@@ -857,10 +855,10 @@ void ipath_sqerror_qp(struct ipath_qp *qspin_lock (&dev->pending_lock);/* XXX What if its already removed by the timeout code? */ -if (qp->timerwait.next !=LIST_POISON1 ) -list_del (&qp->timerwait); -if (qp->piowait.next !=LIST_POISON1 ) -list_del (&qp->piowait); +if (!list_empty (&qp->timerwait)) +list_del_init (&qp->timerwait); +if (!list_empty (&qp->piowait)) +list_del_init (&qp->piowait);spin_unlock (&dev->pending_lock);ipath_cq_enter (to_icq (qp->ibqp.send_cq), wc,1 );
drivers/infiniband/hw/ipath/ipath_rc.c +7 -8
@@ -57,7 +57,7 @@ static void ipath_init_restart(struct ip qp->s_len = wqe->length - len; dev =to_idev (qp->ibqp.device);spin_lock (&dev->pending_lock); -if (qp->timerwait.next ==LIST_POISON1 ) +if (list_empty (&qp->timerwait))list_add_tail (&qp->timerwait, &dev->pending[dev->pending_index]);spin_unlock (&dev->pending_lock);
@@ -356,7 +356,7 @@ static inline int ipath_make_rc_req(struif ((int )(qp->s_psn - qp->s_next_psn) >0 ) qp->s_next_psn = qp->s_psn;spin_lock (&dev->pending_lock); -if (qp->timerwait.next ==LIST_POISON1 ) +if (list_empty (&qp->timerwait))list_add_tail (&qp->timerwait, &dev->pending[dev->pending_index]);spin_unlock (&dev->pending_lock);
@@ -726,8 +726,8 @@ void ipath_restart_rc(struct ipath_qp *q*/ dev =to_idev (qp->ibqp.device);spin_lock (&dev->pending_lock); -if (qp->timerwait.next !=LIST_POISON1 ) -list_del (&qp->timerwait); +if (!list_empty (&qp->timerwait)) +list_del_init (&qp->timerwait);spin_unlock (&dev->pending_lock);if (wqe->wr.opcode ==IB_WR_RDMA_READ )
@@ -886,8 +886,8 @@ static int do_rc_ack(struct ipath_qp *qp* just won't find anything to restart if we ACK everything. */ spin_lock (&dev->pending_lock); -if (qp->timerwait.next !=LIST_POISON1 ) -list_del (&qp->timerwait); +if (!list_empty (&qp->timerwait)) +list_del_init (&qp->timerwait);spin_unlock (&dev->pending_lock);/*
@@ -1194,8 +1194,7 @@ static inline void ipath_rc_rcv_resp(str IB_WR_RDMA_READ)) goto ack_done;spin_lock (&dev->pending_lock); -if (qp->s_rnr_timeout ==0 && - qp->timerwait.next !=LIST_POISON1 ) +if (qp->s_rnr_timeout ==0 && !list_empty (&qp->timerwait))list_move_tail (&qp->timerwait, &dev->pending[dev->pending_index]);spin_unlock (&dev->pending_lock);
drivers/infiniband/hw/ipath/ipath_ruc.c +1 -1
@@ -435,7 +435,7 @@ void ipath_no_bufs_available(struct ipatunsigned long flags;spin_lock_irqsave (&dev->pending_lock, flags); -if (qp->piowait.next ==LIST_POISON1 ) +if (list_empty (&qp->piowait))list_add_tail (&qp->piowait, &dev->piowait);spin_unlock_irqrestore (&dev->pending_lock, flags);/*
drivers/infiniband/hw/ipath/ipath_verbs.c +3 -3
@@ -464,7 +464,7 @@ static void ipath_ib_timer(void *arg) last = &dev->pending[dev->pending_index];while (!list_empty (last)) { qp = list_entry(last->next, struct ipath_qp, timerwait); -list_del (&qp->timerwait); +list_del_init (&qp->timerwait); qp->timer_next = resend; resend = qp;atomic_inc (&qp->refcount);
@@ -474,7 +474,7 @@ static void ipath_ib_timer(void *arg) qp = list_entry(last->next, struct ipath_qp, timerwait);if (--qp->s_rnr_timeout ==0 ) { do { - list_del(&qp->timerwait); + list_del_init(&qp->timerwait); tasklet_hi_schedule(&qp->s_task); if (list_empty(last)) break;
@@ -554,7 +554,7 @@ static int ipath_ib_piobufavail(void *arwhile (!list_empty (&dev->piowait)) { qp = list_entry(dev->piowait.next, struct ipath_qp, piowait); -list_del (&qp->piowait); +list_del_init (&qp->piowait);tasklet_hi_schedule (&qp->s_task); }spin_unlock_irqrestore (&dev->pending_lock, flags);
PATCH 1/1 ipath - fix NULL dereference during cleanup
In reply to Bryan O'SullivanFix NULL deref due to pcidev being clobbered before dd->ipath_f_cleanup() was called.
drivers/infiniband/hw/ipath/ipath_driver.c +11 -11
@@ -1905,19 +1905,19 @@ static void __exit infinipath_cleanup(vo }else ipath_dbg ("irq is 0, not doing free_irq " "for unit %u\n" , dd->ipath_unit); + +/* +* we check for NULL here, because it's outside +* the kregbase check, and we need to call it +* after the free_irq. Thus it's possible that +* the function pointers were never initialized. +*/ +if (dd->ipath_f_cleanup) +/* clean up chip-specific stuff */ + dd->ipath_f_cleanup (dd); + dd->pcidev =NULL ; } - -/* -* we check for NULL here, because it's outside the kregbase -* check, and we need to call it after the free_irq. Thus -* it's possible that the function pointers were never -* initialized. -*/ -if (dd->ipath_f_cleanup) -/* clean up chip-specific stuff */ - dd->ipath_f_cleanup (dd); -spin_lock_irqsave (&ipath_devs_lock, flags); }
PATCH 1/1 ipath - don't modify QP if changes fail
In reply to Bryan O'SullivanMake sure modify_qp won't modify the QP if any of the changes failed.
drivers/infiniband/hw/ipath/ipath_qp.c +17 -15
@@ -427,6 +427,7 @@ int ipath_modify_qp(struct ib_qp *ibqp,int ipath_modify_qp (struct ib_qp *ibqp,struct ib_qp_attr *attr,int attr_mask) { +struct ipath_ibdev *dev =to_idev (ibqp->device);struct ipath_qp *qp =to_iqp (ibqp);enum ib_qp_state cur_state, new_state;unsigned long flags;
@@ -443,6 +444,19 @@ int ipath_modify_qp(struct ib_qp *ibqp, attr_mask)) goto inval; +if (attr_mask &IB_QP_AV ) +if (attr->ah_attr.dlid ==0 || + attr->ah_attr.dlid >=IPS_MULTICAST_LID_BASE ) + goto inval; + +if (attr_mask &IB_QP_PKEY_INDEX ) +if (attr->pkey_index >=ipath_layer_get_npkeys (dev->dd)) + goto inval; + +if (attr_mask &IB_QP_MIN_RNR_TIMER ) +if (attr->min_rnr_timer >31 ) + goto inval; +switch (new_state) {case IB_QPS_RESET :ipath_reset_qp (qp);
@@ -457,13 +471,8 @@ int ipath_modify_qp(struct ib_qp *ibqp, } -if (attr_mask &IB_QP_PKEY_INDEX ) { -struct ipath_ibdev *dev =to_idev (ibqp->device); - -if (attr->pkey_index >=ipath_layer_get_npkeys (dev->dd)) - goto inval; +if (attr_mask &IB_QP_PKEY_INDEX ) qp->s_pkey_index = attr->pkey_index; - }if (attr_mask &IB_QP_DEST_QPN ) qp->remote_qpn = attr->dest_qp_num;
@@ -479,12 +488,8 @@ int ipath_modify_qp(struct ib_qp *ibqp,if (attr_mask &IB_QP_ACCESS_FLAGS ) qp->qp_access_flags = attr->qp_access_flags; -if (attr_mask &IB_QP_AV ) { -if (attr->ah_attr.dlid ==0 || - attr->ah_attr.dlid >=IPS_MULTICAST_LID_BASE ) - goto inval; +if (attr_mask &IB_QP_AV ) qp->remote_ah_attr = attr->ah_attr; - }if (attr_mask &IB_QP_PATH_MTU ) qp->path_mtu = attr->path_mtu;
@@ -499,11 +504,8 @@ int ipath_modify_qp(struct ib_qp *ibqp, qp->s_rnr_retry_cnt = qp->s_rnr_retry; } -if (attr_mask &IB_QP_MIN_RNR_TIMER ) { -if (attr->min_rnr_timer >31 ) - goto inval; +if (attr_mask &IB_QP_MIN_RNR_TIMER ) qp->s_min_rnr_timer = attr->min_rnr_timer; - }if (attr_mask &IB_QP_QKEY ) qp->qkey = attr->qkey;