Skip to contentSkip to conversation

smsc47m192: New hwmon driver for

PATCH New Greg KH 1 participant 1 message Jun 22, 2006

Subsystems (2)
lore
Share & tools
lore

Greg KH

author
#0 lore raw

PATCH 4/44 smsc47m192: New hwmon driver for

From: Hartmut Rick <linux at rick.claranet.de>

New driver (smsc47m192) which supports voltage and temperature measurement features of SMSC LPC47M192 and LPC47M997 chips.

Signed-off-by Hartmut Rick <linux at rick.claranet.de>
Signed-off-by Jean Delvare <khali at linux-fr.org>
Signed-off-by Greg Kroah-Hartman <gregkh at suse.de>
---
 Documentation/hwmon/smsc47m192      |  102 ++++++
 Documentation/hwmon/sysfs-interface |    6 
 drivers/hwmon/Kconfig               |   23 +
 drivers/hwmon/Makefile              |    1 
 drivers/hwmon/smsc47m192.c          |  648 +++++++++++++++++++++++++++++++++++
 5 files changed, 779 insertions(+), 1 deletions(-)
Documentation/hwmon/smsc47m192 new file +102 -0
new file mode 100644
index 0000000..45d6453
@@ -0,0 +1,102 @@
+Kernel driver smsc47m192
+============
+
+Supported chips:
+  * SMSC LPC47M192 and LPC47M997
+    Prefix: 'smsc47m192'
+    Addresses scanned: I2C 0x2c - 0x2d
+    Datasheet: The datasheet for LPC47M192 is publicly available from
+               http://www.smsc.com/
+               The LPC47M997 is compatible for hardware monitoring.
+
+Author: Hartmut Rick <linux at rick.claranet.de>
+        Special thanks to Jean Delvare for careful checking
+        of the code and many helpful comments and suggestions.
+
+
+Description
+-----------
+
+This driver implements support for the hardware sensor capabilities
+of the SMSC LPC47M192 and LPC47M997 Super-I/O chips.
+
+These chips support 3 temperature channels and 8 voltage inputs
+as well as CPU voltage VID input.
+
+They do also have fan monitoring and control capabilities, but the
+these features are accessed via ISA bus and are not supported by this
+driver. Use the 'smsc47m1' driver for fan monitoring and control.
+
+Voltages and temperatures are measured by an 8-bit ADC, the resolution
+of the temperatures is 1 bit per degree C.
+Voltages are scaled such that the nominal voltage corresponds to
+192 counts, i.e. 3/4 of the full range. Thus the available range for
+each voltage channel is 0V ... 255/192*(nominal voltage), the resolution
+is 1 bit per (nominal voltage)/192.
+Both voltage and temperature values are scaled by 1000, the sys files
+show voltages in mV and temperatures in units of 0.001 degC.
+
+The +12V analog voltage input channel (in4_input) is multiplexed with
+bit 4 of the encoded CPU voltage. This means that you either get
+a +12V voltage measurement or a 5 bit CPU VID, but not both.
+The default setting is to use the pin as 12V input, and use only 4 bit VID.
+This driver assumes that the information in the configuration register
+is correct, i.e. that the BIOS has updated the configuration if
+the motherboard has this input wired to VID4.
+
+The temperature and voltage readings are updated once every 1.5 seconds.
+Reading them more often repeats the same values.
+
+
+sysfs interface
+---------------
+
+in0_input	- +2.5V voltage input
+in1_input	- CPU voltage input (nominal 2.25V)
+in2_input	- +3.3V voltage input
+in3_input	- +5V voltage input
+in4_input	- +12V voltage input (may be missing if used as VID4)
+in5_input	- Vcc voltage input (nominal 3.3V)
+		  This is the supply voltage of the sensor chip itself.
+in6_input	- +1.5V voltage input
+in7_input	- +1.8V voltage input
+
+in[0-7]_min,
+in[0-7]_max	- lower and upper alarm thresholds for in[0-7]_input reading
+
+		  All voltages are read and written in mV.
+
+in[0-7]_alarm	- alarm flags for voltage inputs
+		  These files read '1' in case of alarm, '0' otherwise.
+
+temp1_input	- chip temperature measured by on-chip diode
+temp[2-3]_input	- temperature measured by external diodes (one of these would
+		  typically be wired to the diode inside the CPU)
+
+temp[1-3]_min,
+temp[1-3]_max	- lower and upper alarm thresholds for temperatures
+
+temp[1-3]_offset - temperature offset registers
+		  The chip adds the offsets stored in these registers to
+		  the corresponding temperature readings.
+		  Note that temp1 and temp2 offsets share the same register,
+		  they cannot both be different from zero at the same time.
+		  Writing a non-zero number to one of them will reset the other
+		  offset to zero.
+
+		  All temperatures and offsets are read and written in
+		  units of 0.001 degC.
+
+temp[1-3]_alarm - alarm flags for temperature inputs, '1' in case of alarm,
+		  '0' otherwise.
+temp[2-3]_input_fault - diode fault flags for temperature inputs 2 and 3.
+		  A fault is detected if the two pins for the corresponding
+		  sensor are open or shorted, or any of the two is shorted
+		  to ground or Vcc. '1' indicates a diode fault.
+
+cpu0_vid	- CPU voltage as received from the CPU
+
+vrm		- CPU VID standard used for decoding CPU voltage
+
+		  The *_min, *_max, *_offset and vrm files can be read and
+		  written, all others are read-only.
Documentation/hwmon/sysfs-interface +6 -0
index a0d0ab2..2d16e1e 100644
@@ -218,6 +218,12 @@ temp[1-2]_crit_hyst
 		from the critical value.
 		Read/Write value.
 
+temp[1-4]_offset
+		Temperature offset which is added to the temperature reading
+		by the chip.
+		Unit: millidegree Celsius
+		Read/Write value.
+
 		If there are multiple temperature sensors, temp1_* is
 		generally the sensor inside the chip itself,
 		reported as "motherboard temperature".  temp2_* to
drivers/hwmon/Kconfig +22 -1
index a6a8d66..9cf3d9c 100644
@@ -333,11 +333,32 @@ config SENSORS_SMSC47M1
 	help
 	  If you say yes here you get support for the integrated fan
 	  monitoring and control capabilities of the SMSC LPC47B27x,
-	  LPC47M10x, LPC47M13x, LPC47M14x, LPC47M15x and LPC47M192 chips.
+	  LPC47M10x, LPC47M13x, LPC47M14x, LPC47M15x, LPC47M192 and
+	  LPC47M997 chips.
+
+	  The temperature and voltage sensor features of the LPC47M192
+	  and LPC47M997 are supported by another driver, select also
+	  "SMSC LPC47M192 and compatibles" below for those.
 
 	  This driver can also be built as a module.  If so, the module
 	  will be called smsc47m1.
 
+config SENSORS_SMSC47M192
+	tristate "SMSC LPC47M192 and compatibles"
+	depends on HWMON && I2C && EXPERIMENTAL
+	select HWMON_VID
+	help
+	  If you say yes here you get support for the temperature and
+	  voltage sensors of the SMSC LPC47M192 and LPC47M997 chips.
+
+	  The fan monitoring and control capabilities of these chips
+	  are supported by another driver, select
+	  "SMSC LPC47M10x and compatibles" above. You need both drivers
+	  if you want fan control and voltage/temperature sensor support.
+
+	  This driver can also be built as a module.  If so, the module
+	  will be called smsc47m192.
+
 config SENSORS_SMSC47B397
 	tristate "SMSC LPC47B397-NC"
 	depends on HWMON && I2C && EXPERIMENTAL
drivers/hwmon/Makefile +1 -0
index fbdb8d9..d090459 100644
@@ -40,6 +40,7 @@ obj-$(CONFIG_SENSORS_PC87360)	+= pc87360
 obj-$(CONFIG_SENSORS_SIS5595)	+= sis5595.o
 obj-$(CONFIG_SENSORS_SMSC47B397)+= smsc47b397.o
 obj-$(CONFIG_SENSORS_SMSC47M1)	+= smsc47m1.o
+obj-$(CONFIG_SENSORS_SMSC47M192)+= smsc47m192.o
 obj-$(CONFIG_SENSORS_VIA686A)	+= via686a.o
 obj-$(CONFIG_SENSORS_VT8231)	+= vt8231.o
 obj-$(CONFIG_SENSORS_W83627EHF)	+= w83627ehf.o
drivers/hwmon/smsc47m192.c new file +648 -0

648 lines not on this page · raw message

Signature · 1 line
1.4.0